Products from VERATRON Marine
VERATRON VMH 35 D multifunction display
€349.90 *
Attractive, very versatile digital round instrument from the Swiss quality supplier Veratron (formerly VDO), which can display up to 30 digital data sets from the on-board system. Both NMEA 2000 data and analog measured values can be used. TFT display made of mineral glass with brushed stainless steel bezel, waterproof to IPX7, therefore also suitable for the cockpit.Speed, heading, course, rpm, tank levels, depth, etc. can be displayed on 20 screen surfaces. It is also possible to set alarm thresholds, for example for engine monitoring or depth. A total of 10 via warning icons (e.g. fuel/water tank level, cooling water temperature, oil pressure, oil level, battery voltage, GPS signal loss).Operation via two softkeys, which is easy even when wearing gloves. A GPS chip is integrated in the device, which calculates speed and course. It has an NMEA 2000 input as well as four additional analog inputs, two frequency inputs (engine rpm, logger) and two resistance inputs. The VMH 35 can also be used as the main unit for controlling up to 14 VMH 14 daughter displays via the Veratron EasyLink standard.The menu can be used to set whether the speed should be displayed up to 3000 or 4000 revolutions.Technical dataAnalog inputs: 2x resistance/2X frequencyDigital inputs: 1x NMEA 2000, 1x SAE J193912/24 Volt (9-32 V)Position: GPS, GLONASS, GallileoDiameter: Outside 100mmMounting hole: 85 mmDisplay 1.44 inch TFTEasy-Link output for VMH 16The 100mm display 12 or 24 V, 4 analog inputs. As a main device, the device can supply up to 14 smaller VMH 14 daughter displays with data wirelessly.Power consumption ≤ 170 mA/12V
VERATRON VMH 14 multifunction display
€71.90 *
Daughter display for the main display VMH 35-D from the Swiss quality manufacturer Veratron (formerly VDO). A VMH 35-D must be installed for the VMH 14 to function; it does not work as a stand-alone solution. The compact 56 mm display made of mineral glass with a brushed stainless steel frame can display one of the following 8 measured values: Fuel level, trim, battery voltage, cooling water temperature, oil temperature and oil pressure in the engine or gearbox. The power supply and the necessary measurement data are provided via the VMH 35 main display.The measured values are shown via a round graphic display as well as icons and digits. Alarm thresholds can be set; when these are reached, the values and graphics on the display start to flash.The VMH 14 is suitable for all of the above data on delivery and is simply programmed once for the desired function on board using the Veratron smartphone app (Android or Apple). This works via the NFC function (near field communication) of your own smartphone. The device does not even need to be connected to the on-board power supply. Simply hold your smartphone to the back of the display, start the app and make the settings. The app can also be used to enter units, tank numbers or desired alarm thresholds.Up to 16 additional VMH 14s can be connected to one VMH 35-D. The display is suitable for the cockpit and is waterproof to protection class IPX 7 (30 minutes in 1 m of water). A 52 mm hole in the bulkhead/instrument carrier is required for mounting the display.The scope of delivery includes display, mounting plastic nut, wiring harness and rubber seal.Technical data VMH 14Operating voltage : 12/24 V via main displayPower consumption: ≤ 15 mA/12Display: Optically bonded IBN segment display. Mineral glass.Diameter: 56 mm (display), 52 mm (mounting hole)Installation depth: 40 mmPlug/connection: AMP SuperSeal 1.5 Male: 282105-1 / Female: 282087-1Operating temperature: -20°C to + 60 °C
VERATRON VMH Flex multifunction display NMEA
€146.91 *
Extremely versatile multifunctional circular instrument from the Swiss quality supplier Veratron (formerly VDO). Can display one or two pieces of boat data each on five scrollable screens with digits, icons and bar charts. A total of up to 30 digital data from the on-board system (e.g. speed, course, engine speed, tank levels, depth, cooling water temperature) can be processed.You can scroll by touching the glass display. The screens and desired data are simply selected and configured via the app. The device can process data from the NMEA 2000 network and also has two analog sensor inputs (resistance 0-400 Ohm and 0-1500 Ohm).On delivery, the VMH Flex is suitable for all measured values listed in the technical data below and is simply programmed once for the desired function on board using the Veratron smartphone app (Android or Apple). This works via the NFC function (Near Field Communication) of your own smartphone. The device does not even need to be connected to the on-board power supply. Simply hold your smartphone to the back of the display, start the app and make the settings. The app can also be used to enter units, tank numbers or desired alarm thresholds.Operation via 2 softkeys. Integrated GPS chip, 12 or 24 V, 4 analog inputs. As the main device, the device can supply up to 14 smaller VMH 14 slave displays with data. NMEA 2000 connection.Mineral glass with brushed stainless steel bezel, waterproof to IPX7 (min. 30 minutes 1 m under water), therefore also suitable for the cockpit. The 1.44 inch TFT display, 14 programmable alarmsTechnical dataOperating voltage 12/24 VPower consumption 65mAScreen: 1.44 inch TFT display, 125x125 pixelsInstallation dimensions: 52mm hole, depth: 45 mmConnection: Tyco / Hirschmann MQS connector 8 pin / Micro-C M12 5PinDigital ports: NMEA 2000, LIN busAnalog inputs: 2x resistorWaterproof according to IPx7Wireless interface: AirWave (NFC)Supported data: Battery (volt-ampere meter), RPM, engine operating hours, SOG, COG, depth, trim, engine coolant, boost pressure, engine oil temperature and pressure, transmission oil temperature and pressure, fuel level, fresh water level, holding tank level, rudder position, time, exhaust gas temperature,
