- Rigg & sail
- Rope & cordage
- Anchoring & mooring
- Hull & deck
-
Cabin & comfort
- Lamps, lights & lanterns
- Clocks, barometers & instruments
- Stoves & heaters
- Cooker, oven & barbecue
- Interior fittings
- Cabinet fittings
- Hinges & strap hinges
- Flush handles
- Locks
- Bolts & fasteners
- Hooks
- Clothing
- Life on board
- Store nets & bags
- Bags & duffel bags
- Cushions & mattress
- Maritime decoration
- Key rings
- Paint & boatbuilding
- Electrics & engine
- Pumps & sanitation
- Safety & VHF radio
- Navigation & books
- Commercial shipping
Diesel heaters & stoves
Small, compact cabin stove for operation with diesel oil or heating oil.The oil regulator, which is easily accessible at the front of the stove behind a stainless steel cladding, is easy to operate.The stove door has a viewing window through which the flame can be observed.The NEWPORT is equipped with a 6" stainless steel airflow burner bowl and a 12 volt or 24 volt support fan.Heat output and oil consumption (min / max) 1.9 / 4.75 kW - 0.24 / 0.60 l/h.The required exhaust accessories can be found further down on this page under "Accessories & spare parts".The matching flue gas pipe system has a diameter of 3" / 75 mm.This NEWPORT version is equipped with a stainless steel hot water coil, which is used to heat the domestic hot water directly in a boiler. The coil can run dry without any problems.It is also possible to connect the RADEX heater, which allows a second room to be supplied with hot air.DICKINSON marine oil stoves and oil heaters from Canada have been built since 1932. Originally designed for fishing and commercial shipping, all stoves are characterized by a simple but well thought-out design and solid construction.As far as possible, all stoves are made of stainless steel.Mode of operation: All stoves work according to the simple principle of the pan burner. Either diesel oil or heating oil can be used.The oil runs from a tank, which must be installed at least 30 cm higher than the stove, with a natural gradient to the stove regulator. If no tank can be installed, it is also possible to use an electric oil feed pump.The adjustable oil regulator - developed and manufactured by DICKINSON - regulates the correct oil supply to the burner bowl and ensures a safety shutdown via a float if the flame should go out unintentionally.It functions reliably as it works without any electrical or electronic components that are susceptible to faults. The regulator has a safety cut-out integrated into the control knob, which permanently interrupts the oil supply at temperatures above 75°C. The stoves work very quietly and give off a pleasant, dry heat!To support combustion - especially when lighting the stove or in difficult draught conditions - the adjustable fan under the burner bowl can be switched on.For optimum combustion, all stoves are equipped with a removable flame catalyst (“Superheater”).Under the following link, DICKINSON offers various interesting videos to assist with the maintenance, repair and installation of stoves and ranges:https://www.youtube.com/@DickinsonMarine-since1932
Small, compact cabin stove for operation with diesel oil or heating oil.The oil regulator is easily accessible behind a stainless steel casing.Stove door with viewing window through which the flame can be observed.Equipped with 6" stainless steel airflow burner bowl.Support fan 12 Volt, also available in 24V.Heat output (min/max) 1.9 / 4.75 kW Oil consumption (min/max) 0.24 / 0.60 l/h.Exhaust accessories required: 3" / 75 mm (see accessories & spare parts).Also available with stainless steel hot water coil (pipe diameter 16 mm) for heating service water in an external hot water tank.DICKINSON marine oil stoves and oil stoves from Canada, built since 1932, originally designed for fishing and commercial shipping, all stoves are characterized by a simple but well thought-out design and solid construction. All ovens are made of stainless steel wherever possible.Mode of operation: All ovens work according to the simple principle of the pan burner. Either diesel oil or heating oil can be used. The oil runs from a tank, which must be installed at least 30 cm higher than the stove, with a natural gradient to the stove regulator. If no tank can be installed, it is also possible to use an electric oil feed pump. The adjustable oil regulator - developed and manufactured by DICKINSON - regulates the correct oil supply to the burner bowl and ensures a safety shutdown via a float if the flame should go out unintentionally.Reliable operation, as there are no electrical or electronic components that are susceptible to faults. The regulator has a safety cut-out integrated into the control knob, which permanently interrupts the oil supply at temperatures above 75°C. The stoves work very quietly and give off a pleasant, dry heat!To support combustion - especially when lighting the stove or in difficult draught conditions - the adjustable fan under the burner bowl can be switched on. For optimum combustion, all stoves are equipped with a removable flame catalyst ("superheater").Dickinson offers a variety of interesting videos at the following link to help with the maintenance, repair and installation of stoves and ranges:https://www.youtube.com/@DickinsonMarine-since1932As a Dickinson importer and wholesaler, we carry just about every original spare part and accessory.
Small compact cabin stove as a floor model, diesel oil or heating oil is used as fuel. The oil regulator is easily accessible behind a stainless steel casing. The stove door has a viewing window through which the flame can be observed. The stove is equipped with a 6" stainless steel airflow burner bowl.The support fan is available for both 12 volts and 24 volts.The version with stainless steel hot water coil is designed to heat the domestic hot water directly in a boiler. The coil can run dry without any problems. It is also possible to connect the RADEX heater.Heating capacity and oil consumption: (min/max) 1.9/4.75 kW - 0.24/0.60 l/h.Required exhaust accessories: 3" / 75 mm (see accessories & spare parts). DICKINSON marine oil stoves and oil heaters from Canada, built since 1932. Originally designed for fishing and commercial shipping, all stoves are characterized by a simple but well thought-out design and solid construction. All stoves are, as far as possible, made of stainless steel. The hotplates are made of surface-ground cast iron.How they work: All ovens work according to the simple principle of the bowl burner. Either diesel oil or heating oil can be used. The oil runs from a tank, which must be installed at least 30 cm higher than the stove, with a natural gradient to the stove regulator. If no tank can be installed, it is also possible to use an electric oil feed pump. The adjustable oil regulator - developed and manufactured by DICKINSON - regulates the correct oil supply to the burner bowl and ensures a safety shutdown via a float if the flame should go out unintentionally. The operation is very reliable as there are no electrical or electronic components that are susceptible to faults. The regulator has a safety cut-out integrated into the control knob, which permanently interrupts the oil supply at temperatures above 75°C. The stoves work very quietly and give off a pleasant, dry heat! To support combustion - especially when lighting the stove or in difficult draught conditions - the adjustable fan under the burner bowl can be switched on. For optimum combustion, all stoves are equipped with a removable flame catalyst ("superheater").
Small, compact freestanding cabin stove. Fuel: diesel or heating oil. Fuel regulator easily accessible behind a stainless steel cover. Door with window, through which the flames can be observed. Equipped with 6" Airflow burner shell of rust-free steel.12 volt support ventilator, also available in 24 volt.Heat production (min/max) 1.9 / 4.75 kWFuel consumption (min/max) 0.24 / 0.60 l/h.Required exhaust accessories: 3" / 75 mm (see accessories).Also available with stainless steel hot water coil (pipe diameter 16 mm) for heating domestic hot water in an external hot water tank.DICKINSON ship's stoves of Canada, made since 1932. Originally conceptualized for fishermen and professional mariners, these stoves stand out for their simple, but well-thought-out, design and solid construction. All stoves are, as far as is possible, made of stainless steel. The stove plates are made of ground cast iron.Functionality: All stoves work on the simple shell-burner principle. They can be used with either diesel or heating oil. The oil runs from a tank, which must be installed at least 30 cm higher than the stove, with natural filling serving as regulator. If no tank can be integrated, the use of an electric fuel pump is also possible. The installable regulator - developed and made by DICKINSON - keeps the correct fuel feed to the burner shell and, using a float switch, ensures the feed, in case the flame goes out unnoticed. Reliable functionality, because it runs without failure-prone electronics and electrical systems. The regulator has a safety shutdown integrated in the adjustment knob that breaks the fuel flow when the temperature remains over 75°C. The stoves work very quietly and give off a comfortable, dry warmth! To support the burning - exceptionally when lighting the stove or in difficult circumstances - the adjustable ventilator under that burner shell can be set. For optimal burning, all stoves come equipped with a removable superheater.Dickinson offers a variety of interesting videos at the following link to help with the maintenance, repair and installation of stoves and ranges:https://www.youtube.com/@DickinsonMarine-since1932As a Dickinson importer and wholesaler, we carry just about every original spare part and accessory.
Combination model suitable for heating and cooking. The rectangular cabin oven has a height of just 455 mm and, with its compact dimensions of 275 x 435 mm (width x depth), also fits into a small niche.As is usual with DICKINSON, the stove is made entirely of stainless steel, with a black burnished perforated plate fitted around the perimeter to protect against contact and scuffing.Required exhaust accessories: 4" / 102 mm (see accessories & spare parts).The diesel oil regulator is easily accessible at the front of the stove.A viewing window allows the flame to be checked from the outside.The stove quickly reaches operating temperature thanks to the built-in support fan; the switch and speed regulator are located in a box that can be mounted separately.The stove is equipped with the tried and tested 6" airflow burner.Heat output and oil consumption (min/max): 1.9/4.75 kW - 0.24/0.6 l/h.Weight of the stove: 11 kg.The exhaust outlet leaves enough space for a kettle or a pot on the removable cast iron hotplate.DICKINSON marine oil stoves and ovens from Canada, built since 1932. Originally designed for fishing and commercial shipping, all stoves are characterized by a simple but well thought-out design and solid construction. All stoves are, as far as possible, made of stainless steel. The hotplates are made of surface-ground cast iron.How they work: All ovens work according to the simple principle of the bowl burner. Either diesel oil or heating oil can be used. The oil runs from a tank, which must be installed at least 30 cm higher than the stove, with a natural gradient to the stove regulator. If no tank can be installed, it is also possible to use an electric oil feed pump. The adjustable oil regulator - developed and manufactured by DICKINSON - regulates the correct oil supply to the burner bowl and ensures a safety shutdown via a float if the flame should go out unintentionally.Reliable operation, as there are no electrical or electronic components that are susceptible to faults. The regulator has a safety cut-out integrated into the control knob, which permanently interrupts the oil supply at temperatures above 75°C. The stoves work very quietly and give off a pleasant, dry heat!To support combustion - especially when lighting the stove or in difficult draught conditions - the adjustable fan under the burner bowl can be switched on. For optimum combustion, all stoves are equipped with a removable flame catalyst ("superheater").
Round, compact cabin stove as a floor model, fuel: diesel oil or heating oil. The oil regulator is easily accessible from the front behind a stainless steel cover.This size of stove produces a higher heat output than smaller models, although the fuel consumption remains the same.The stove is characterized by a round design, with a large door and a viewing window through which the flame can be easily observed.Flue accessories required: 3" / 75 mm (see accessories & spare parts).Equipped with 6" stainless steel airflow burner bowl.Support fan 12 volt, also available in 24 volt.Heat output and oil consumption (min/max) 1.9/4.75 kW - 0.24/0.60 l/h.Dimensions W x D x H: 330 x 355 x 635 mm, weight 12.25 kg. DICKINSON marine oil stoves and oil stoves from Canada, built since 1932. Originally designed for fishing and commercial shipping, all stoves are characterized by a simple but well thought-out design and solid construction. All stoves are, as far as possible, made of stainless steel. The hotplates are made of surface-ground cast iron.How they work: All ovens work according to the simple principle of the bowl burner. Either diesel oil or heating oil can be used. The oil runs from a tank, which must be installed at least 30 cm higher than the stove, with a natural gradient to the stove regulator. If no tank can be installed, it is also possible to use an electric oil feed pump. The adjustable oil regulator - developed and manufactured by DICKINSON - regulates the correct oil supply to the burner bowl and ensures a safety shutdown via a float if the flame should go out unintentionally.Reliable operation, as there are no electrical or electronic components that are susceptible to faults. The regulator has a safety cut-out integrated into the control knob, which permanently interrupts the oil supply at temperatures above 75°C. The stoves work very quietly and give off a pleasant, dry heat!To support combustion - especially when lighting the stove or in difficult draught conditions - the adjustable fan under the burner bowl can be switched on. For optimum combustion, all stoves are equipped with a removable flame catalyst ("superheater").
In response to popular demand, REFLEKS offers a viewing window made of special coated glass to monitor the flame. The stove, with its pan-suitable simmering rim and surface-ground cast iron hotplate, fills a gap in the medium heat output range. This compact stove is fitted with a stainless steel burner pot.Exhaust pipe diameter: 90 mm.Total heat output: 4.2 KW (3675 kcal/h).Air output: 4.2 kW.Oil consumption min. / max.: 0.18 / 0.54 l/h.Weight: 10 kg.For insulated rooms: approx. 40-70 cubic meters.For boat sizes up to approx. 15 meters. Model 2000 K: with stainless steel jacketModel 2000 K-Cu: Supplied with a copper jacket.Vehicle version model 2000 K-C:A special version for installation in rooms with problematic supply air conditions (e.g. control stands, camping vehicles). The combustion chamber is therefore encapsulated in such a way that fresh air can only be supplied via the lower pipe without consuming the room air. The scope of delivery includes a stainless steel inlet pipe with fixing lugs that can be permanently installed in the floor. The stove can still be removed.REFLEKS marine ovens and stoves have been specially developed for marine applications. Like the accessories, they are made of stainless steel, with the exhaust area made of acid-resistant stainless steel. The burner bowls are made of precision steel. All furnaces are equipped with a tried-and-tested marine oil regulator, which ensures that the furnace functions perfectly at angles of up to 15° and guarantees a high level of operational safety. More than 100,000 REFLEKS oil stoves have been delivered and have proven themselves for decades on fishing and other vessels in Scandinavia and worldwide. The oil stoves and ranges require no electrical connection, are easy to install, operate completely noiselessly and give off a comfortable heat. Detailed installation and operating instructions are included.
The smallest REFLEKS stove in a simple design with a chimney outlet at the rear. Surface-ground cast iron hotplate with a chimney edge. Available in stainless steel (also with a viewing window or as a vehicle version) or with a copper or brass casing.Suitable for small cabins.Total heating capacity 1.6 kW (1400 kcal/h)Oil consumption min. 0.12 l/hOil consumption max. 0.30 l/hWeight 4.5 kgFor room sizes approx. 14-23 cbm.Vehicle version 66MK-C:A special version for installation in rooms with problematic supply air conditions (e.g. control stands, camping vehicles). For this reason, the combustion chamber is encapsulated in such a way that fresh air can only be supplied via the lower pipe without consuming the room air. The scope of delivery includes a stainless steel inlet pipe with fixing lugs that can be permanently installed in the floor. The stove can still be removed.REFLEKS marine ovens and stoves have been specially developed for marine applications. Like the accessories, they are made of stainless steel, with the exhaust area made of acid-resistant stainless steel.The burner bowls are made of precision steel. All furnaces are equipped with a tried-and-tested marine oil regulator, which ensures that the furnace functions perfectly at angles of up to 15° and guarantees a high level of operational safety. More than 100,000 REFLEKS oil stoves have been delivered and have proven themselves for decades on fishing and other vessels in Scandinavia and worldwide. The oil stoves and ranges require no electrical connection, are easy to install, operate completely noiselessly and give off a comfortable heat. Detailed installation and operating instructions are included.
The smallest REFLEKS stove. Simple design with direct venting above.Available in stainless steel (also with viewing window or as vehicle version) or with copper jacket. Intended for small cabins.Model 66 M:Total heat output: 1.6 kW (1400 kcal/h)Fuel consumption: min. 0.12 l/hFuel consumption: max. 0.30 l/hWeight: 4.5 kgFor room sizes of approx. 14 - 23 m.sq.Motor vehicle version 66M-C:A version of the REFLEKS stove specially designed for the placement in spaces with a problematic air supply situation (i. e. comand stations, campers, etc.). The burner chamber is capsulated in such a way, that fresh air is solely sucked in through a tube from the outside without using up the oxygen in the room. Shipping with a stainless steel inlet tube with fixing clamps for mounting permanently in the floor. The stove is still removable. REFLEKS boat heaters and stoves have been developed specially for voyaging at sea. They and all their accessories are made of rust-free stainless steel; in the exhaust region, of acid-resistant stainless steel. The burner bowls are made of precision steel.All heaters are fitted with a proven marine oil regulator,which ensures faultless performance to 15°of heel and a high level of safety.REFLEKS ships' ovens and stoves have been developed specially for shipping. They and their accessories are made of rust-free stainless steel; in exhaust areas, acid-proof stainless steel.The burner shells are made of precision steel.All stoves are equipped with a proven ship's fuel regulator, that ensures the trouble-free function of the stove at heeling angles of up to 15° and a high level of reliability.More than 100,000 REFLEKS stoves have proven themselves worldwide for decades aboard fishing and other vessels in Scandinavia. They require no electrical connection, are easy to install, work totally odor-free and give off a cozy warmth. Extensive installation and instruction manuals are included.
Tried and tested oil stove for smaller rooms. This small stove is equipped with a hotplate and sling rail as well as a viewing window: this allows you to keep the kettle warm with a cozy firelight.Model 62 MKG. Total heat output 2.4 kW (2100 kcal/h) Oil consumption min. / max. 0.12 / 0.36 l/h Weight 7 kg For room sizes approx. 21 cbm (poorly insulated room) to 35 cbm (with good insulation) REFLEKS marine ovens and stoves have been specially developed for maritime shipping. Like the accessories, they are made of stainless steel, with the flue gas area made of acid-resistant stainless steel. The burner bowls are made of precision steel. All furnaces are equipped with a tried-and-tested marine oil regulator, which ensures that the furnace functions perfectly at angles of up to 15° and guarantees a high level of operational safety. More than 100,000 REFLEKS oil stoves have been delivered and have proven themselves for decades on fishing and other vessels in Scandinavia and worldwide. The oil stoves and ranges require no electrical connection, are easy to install, operate completely silently and give off a comfortable heat. Detailed installation and operating instructions are included.
Tried-and-tested medium-sized oil stove in an inexpensive standard design, with a surface-ground cast iron hotplate and slinger rim. Model 60MK.Total heating capacity 5.8 kW (5000 kcal/h) Oil consumption min. / max. 0.18 / 0.8 l/h Weight 10 kg For room sizes approx. 50 cbm (poorly insulated room) to 83 cbm (with good insulation). RELFLEKS marine oil stoves and ranges have been specially developed for maritime shipping. Like the accessories, they are made of stainless steel, with the flue gas area made of acid-resistant stainless steel. The burner bowls are made of precision steel. All furnaces are equipped with a tried-and-tested marine oil regulator, which ensures that the furnace functions perfectly at angles of up to 15° and guarantees a high level of operational safety. More than 100,000 REFLEKS oil stoves have been delivered and have proven themselves for decades on fishing and other vessels in Scandinavia and worldwide. The oil stoves and ranges do not require an electrical connection, are easy to install, operate completely silently and give off a comfortable heat. Detailed installation and operating instructions are included.
Central oil heater with copper heating coil for connecting radiators and a water heater. Supplied with a slip rim.Model 61 MS: Total heat output 5.8 kW (5000 kcal/h) Heat output water 3.9 kW (3400 kcal/h) Heat output air 1.9 kW (1600 kcal/h) Oil consumption min. / max. 0.18 / 0.8 l/h Weight 14 kg For room sizes approx. 50 cbm (poorly insulated room) to 83 cbm (with good insulation)REFLEKS marine ovens and stoves have been specially developed for maritime shipping. Like the accessories, they are made of stainless steel, with the flue gas area made of acid-resistant stainless steel. The burner bowls are made of precision steel. All furnaces are equipped with a tried-and-tested marine oil regulator, which ensures that the furnace functions perfectly at angles of up to 15° and guarantees a high level of operational safety. More than 100,000 REFLEKS oil stoves have been delivered and have proven themselves for decades on fishing and other vessels in Scandinavia and worldwide. The oil stoves and ranges require no electrical connection, are easy to install, operate completely noiselessly and give off a comfortable heat. Detailed installation and operating instructions are included.
Central oil stove with copper heating coil for connecting radiators and a water heater. Additionally equipped with a surface-ground cast iron hotplate and a slinger rim.Model 61 MKS Total heat output 5.8 kW (5000 kcal/h) Heat output water 3.9 kW (3400 kcal/h) Heat output air 1.9 kW (1600 kcal/h) Oil consumption min. / max. 0.18 / 0.8 l/h Weight 14 kg For room sizes approx. 50 cbm (poorly insulated room) to 83 cbm (with good insulation)Marine oil stoves and ranges are specially developed for maritime shipping. Like the accessories, they are made of stainless steel, with the flue gas area made of acid-resistant stainless steel. The burner bowls are made of precision steel. All furnaces are equipped with a tried-and-tested marine oil regulator, which ensures that the furnace functions perfectly at angles of up to 15° and guarantees a high level of operational safety.More than 100,000 REFLEKS oil stoves have been delivered and have proven themselves for decades on fishing and other vessels in Scandinavia and worldwide.The oil stoves and ranges require no electrical connection, are easy to install, operate completely silently and give off a comfortable heat. Detailed installation and operating instructions are included.
In response to popular demand, REFLEKS offers a viewing window made of special coated glass to monitor the flame. This stove has a pan-suitable simmering rim and a surface-ground cast iron hotplate.The stove is equipped with a boiler developed by REFLEKS made of stainless steel sheet (1.5 mm wall thickness) for connecting radiators or hot water boilers. The connections for the hot water circuit of the stove have a 1/2" internal thread.The stove can also be used without water without any problems (suitable for dry running).Flue pipe diameter: 90 mm.Hot water circuit connections: 1/2" internal threadTotal output: 4.2 kW (3675 kcal/h).Water output: 2.7 kW (2375 kcal/h).Air output: 1.5 kW (1300 kcal/h).Oil consumption min. / max.: 0.18 / 0.54 l/h.Weight: 11.5 kg.For insulated rooms approx.: 40-70 cubic meters.For boat sizes up to approx. 15 meters.Model 2000 K:Standard version with stainless steel jacketModel 2000 K-Cu:As standard version but with a copper sheath.Model 2000 KV-C:Vehicle version - A special version for installation in rooms with problematic air supply conditions (e.g. control stands, camping vehicles). The combustion chamber is therefore encapsulated in such a way that fresh air can only be supplied via the lower pipe without consuming the room air. The scope of delivery includes a stainless steel inlet pipe with fixing lugs that can be permanently installed in the floor. The stove can still be removed.REFLEKS marine ovens and stoves have been specially developed for marine applications. Like the accessories, they are made of stainless steel, with the exhaust area made of acid-resistant stainless steel. The burner bowls are made of precision steel.All furnaces are equipped with a tried-and-tested marine oil regulator, which ensures that the furnace functions perfectly at angles of up to 15° and guarantees a high level of operational safety. More than 100,000 REFLEKS oil stoves have been delivered and have proven themselves for decades on fishing and other vessels in Scandinavia and worldwide. The oil stoves and ranges require no electrical connection, are easy to install, operate completely noiselessly and give off a comfortable heat.Detailed installation and operating instructions are included.
Tried and tested medium-sized stainless steel oil stove in an inexpensive standard version with a slinger rim, but without a hotplate.Model: 60 M Total heating capacity: 5.8 kW (5000 kcal/h)Oil consumption min. / max.: 0.18 / 0.8 l/hWeight: 10 kgFor room sizes approx. 50 cbm (poorly insulated room) to 83 cbm (with good insulation). The REFLEKS marine oil stoves and ranges have been specially developed for maritime shipping. Like the accessories, they are made of stainless steel, with the exhaust area made of acid-resistant stainless steel. The burner bowls are made of precision steel. All furnaces are equipped with a tried and tested marine oil regulator, which ensures that the furnace functions perfectly at an angle of up to 15° and guarantees a high level of operational safety. More than 100,000 REFLEKS oil stoves have been delivered and have proven themselves for decades on fishing boats and other vessels in Scandinavia and worldwide. The oil stoves and ranges do not require an electrical connection, are easy to install, operate completely silently and give off a comfortable heat. Detailed installation and operating instructions are included.Please download the REFLEKS brochure under "Downloads & Information" or request the brochure (INFO No. 12) from us.
Proven oil stove for smaller ships or cabins.Model 62 M. Total heat output 2.4 kW (2100 kcal/h) Oil consumption min. / max. 0.12 / 0.36 l/h Weight 7 kg For room sizes approx. 21 cbm (poorly insulated room) to 35 cbm (with good insulation)Vehicle version 62M-C A special version for installation in rooms with problematic supply air conditions (e.g. control stands, camping vehicles). The combustion chamber is therefore encapsulated in such a way that fresh air can only be supplied via the lower pipe without consuming the room air. The scope of delivery includes a stainless steel inlet pipe with fixing lugs that can be permanently installed in the floor. The stove can still be removed. REFLEKS marine ovens and stoves have been specially developed for marine applications. Like the accessories, they are made of stainless steel, with the exhaust area made of acid-resistant stainless steel. The burner bowls are made of precision steel. All furnaces are equipped with a tried-and-tested marine oil regulator, which ensures that the furnace functions perfectly at angles of up to 15° and guarantees a high level of operational safety. More than 100,000 REFLEKS oil stoves have been delivered and have proven themselves for decades on fishing and other vessels in Scandinavia and worldwide. The oil stoves and ranges require no electrical connection, are easy to install, operate completely silently and give off a comfortable heat. Detailed installation and operating instructions are included.
Proven fuel stove for small boats or cabins. Design with copper heating coil for attachment to heatersModel 62 MS. Total heat output: 2.4 kW (2100 kcal/h) Warm-water output: 1.6 kW Warm-air output: 0.8 kW Fuel consumption: min. / max. 0.12 / 0.36 l/h Weight: 8 kg For room sizes of approx. 21 - 35 m.sq.REFLEKS ships' ovens and stoves have been developed specially for shipping. They and their accessories are made of rust-free stainless steel; in exhaust areas, acid-proof stainless steel.The burner shells are made of precision steel.All stoves are equipped with a proven ship's fuel regulator, that ensures the trouble-free function of the stove at heeling angles of up to 15° and a high level of reliability.More than 100,000 REFLEKS stoves have proven themselves worldwide for decades aboard fishing and other vessels in Scandinavia. They require no electrical connection, are easy to install, work totally odor-free and give off a cozy warmth. Extensive installation and instruction manuals are included.
Tried-and-tested oil stove with ground cast iron hotplate and a 70 mm-high rim. For smaller ships or cabins.Model 62 MK.Total heat output 2.4 kW (2100 kcal/h)Oil consumption min./max. 0.12 / 0.36 l/hWeight 7 kgFor room sizes approx. 21 cbm (poorly insulated room) to 35 cbm (with good insulation).Vehicle version 62MK-CA special version for installation in rooms with problematic supply air conditions (e.g. control stands, camping vehicles). The combustion chamber is therefore encapsulated in such a way that fresh air can only be supplied via the lower pipe without consuming the room air. The scope of delivery includes a stainless steel inlet pipe with fixing lugs that can be permanently installed in the floor. The stove can still be removed.REFLEKS marine ovens and stoves have been specially developed for marine applications. Like the accessories, they are made of stainless steel, with the exhaust area made of acid-resistant stainless steel.The burner bowls are made of precision steel. All furnaces are equipped with a tried-and-tested marine oil regulator, which ensures that the furnace functions perfectly at angles of up to 15° and guarantees a high level of operational safety. More than 100,000 REFLEKS oil stoves have been delivered and have proven themselves for decades on fishing and other vessels in Scandinavia and worldwide. The oil stoves and ranges require no electrical connection, are easy to install, operate completely silently and give off a comfortable heat. Detailed installation and operating instructions are included.
Tried and tested oil stove with copper heating coil for connecting radiators, also with surface-ground cast-iron hotplate and sloped edge (70 mm). For smaller ships or cabins.Model 62 MKS.Total heat output 2.4 kW (2100 kcal/h)Heat output water 1.6 kWHeat output air 0.8 kWOil consumption min./max.0.12/0.36 l/hWeight 8 kgFor room sizes approx. 21-35 cbmREFLEKS marine oil stoves and ranges have been specially developed for maritime shipping. Like the accessories, they are made of stainless steel, with the flue gas area made of acid-resistant stainless steel. The burner bowls are made of precision steel. All furnaces are equipped with a tried-and-tested marine oil regulator, which ensures that the furnace functions perfectly at angles of up to 15° and guarantees a high level of operational safety. More than 100,000 REFLEKS oil stoves have been delivered and have proven themselves for decades on fishing and other vessels in Scandinavia and worldwide. The oil stoves and ranges do not require an electrical connection, are easy to install, operate completely silently and give off a comfortable heat. Detailed installation and operating instructions are included.
Proven oil stove with viewing window for smaller ships or cabins.Model 62 MG. Total heating capacity 2.4 kW (2100 kcal/h) Oil consumption min. / max. 0.12 / 0.36 l/h Weight 7 kg For room sizes approx. 21 cbm (poorly insulated room) to 35 cbm (with good insulation) REFLEKS marine ovens and stoves have been specially developed for maritime shipping. Like the accessories, they are made of stainless steel, with the flue gas area made of acid-resistant stainless steel. The burner bowls are made of precision steel. All furnaces are equipped with a tried-and-tested marine oil regulator, which ensures that the furnace functions perfectly at angles of up to 15° and guarantees a high level of operational safety. More than 100,000 REFLEKS oil stoves have been delivered and have proven themselves for decades on fishing and other vessels in Scandinavia and worldwide. The oil stoves and ranges do not require an electrical connection, are easy to install, operate completely silently and give off a comfortable heat. Detailed installation and operating instructions are included.
The smallest stove in a simple design with direct flue gas outlet to the top. Equipped with an additional heating coil made of copper pipe for operating an external heater. Suitable for small cabins.Model 66 MS. Total heat output 1.6 kW (1400 kcal/h) Heat output water 0.9 kW (800 kcal/h) Heat output air 0.7 kW (600 kcal/h) For room sizes approx. 14-23 cbmVehicle version 66MS-C A special version for installation in rooms with problematic supply air conditions (e.g. control stands, camping vehicles). For this reason, the combustion chamber is encapsulated in such a way that fresh air can only be supplied via the lower pipe without consuming the room air. The scope of delivery includes a stainless steel inlet pipe with fixing lugs that can be permanently installed in the floor. The stove can still be removed. REFLEKS marine ovens and stoves have been specially developed for marine applications. Like the accessories, they are made of stainless steel, with the exhaust area made of acid-resistant stainless steel. The burner bowls are made of precision steel. All furnaces are equipped with a tried-and-tested marine oil regulator, which ensures that the furnace functions perfectly at angles of up to 15° and guarantees a high level of operational safety. More than 100,000 REFLEKS oil stoves have been delivered and have proven themselves for decades on fishing and other vessels in Scandinavia and worldwide. The oil stoves and ranges require no electrical connection, are easy to install, operate completely noiselessly and give off a comfortable heat. Detailed installation and operating instructions are included.
In this version, the REFLEKS 66 stove is equipped with a surface-ground cast iron hotplate and an additional heating coil made of copper pipe for connecting radiators or a water heater.Model 66 MKS: Total heat output 1.6 kW (1400kcal/h) Heat output water 0.9 kW (800kcal/h) Heat output air 0.8 kW (600kcal/h) For room sizes approx. 14-23 cbm A specially refined version 66MKS-Cu of this stove is supplied with a copper jacket instead of the stainless steel jacket. Vehicle version 66MKS-C A special version for installation in rooms with problematic air supply conditions (e.g. control stands, camping vehicles). The combustion chamber is therefore encapsulated in such a way that fresh air can only be supplied via the lower pipe without consuming the room air. The scope of delivery includes a stainless steel inlet pipe with fixing lugs that can be permanently installed in the floor. The stove can still be removed. REFLEKS marine ovens and stoves have been specially developed for marine applications. Like the accessories, they are made of stainless steel, with the exhaust area made of acid-resistant stainless steel. The burner bowls are made of precision steel. All furnaces are equipped with a tried-and-tested marine oil regulator, which ensures that the furnace functions perfectly at angles of up to 15° and guarantees a high level of operational safety. More than 100,000 REFLEKS oil stoves have been delivered and have proven themselves for decades on fishing and other vessels in Scandinavia and worldwide. The oil stoves and ranges do not require an electrical connection, are easy to install, operate completely silently and give off a comfortable heat. Detailed installation and operating instructions are included.
A fully insulated version of the REFLEKS stove, based on the proven "cold stove principle". Water is heated inside the stove in a boiler room and delivered to the radiator or water heater. This oven is therefore well suited for installation in machine rooms, cupboards or narrow niches. A fresh air supply is required.Model 66 MV. Total heating output 1.6 kW (1400kcal/h) Oil consumption min. 0.12 l/h Oil consumption max. 0.36 l/h Weight 8.0 kg For room sizes approx. 14-23 cbm REFLEKS marine oil stoves and ranges have been specially developed for maritime shipping. Like the accessories, they are made of stainless steel, with the flue gas area made of acid-resistant stainless steel. The burner bowls are made of precision steel. All furnaces are equipped with a tried-and-tested marine oil regulator, which ensures that the furnace functions perfectly at angles of up to 15° and guarantees a high level of operational safety. More than 100,000 REFLEKS oil stoves have been delivered and have proven themselves for decades on fishing and other vessels in Scandinavia and worldwide. The oil stoves and ranges require no electrical connection, are easy to install, operate completely silently and give off a comfortable heat. Detailed installation and operating instructions are included.
The small REFLEKS stove as an elegant wall-mounted model. In this model, the oil regulator is integrated in the housing and the flue gas outlet is directly at the top. The stove is also available with a viewing window.Model 66 MW (wall).Total heat output 1.6 kW (1400 kcal/h)Oil consumption min. 0.12 l/hOil consumption max. 0.36 l/hWidth: only slim 170 mm. Weight 5.5 kgFor room sizes approx. 14 - 23 cbmREFLEKS marine oil stoves and ranges have been specially developed for maritime shipping. Like the accessories, they are made of stainless steel, with the exhaust area made of acid-resistant stainless steel. The burner bowls are made of precision steel. All furnaces are equipped with a tried-and-tested marine oil regulator, which ensures that the furnace functions perfectly at angles of up to 15° and guarantees a high level of operational safety. More than 100,000 REFLEKS oil stoves have been delivered and have proven themselves for decades on fishing and other vessels in Scandinavia and worldwide. The oil stoves and ranges require no electrical connection, are easy to install, operate completely noiselessly and give off a comfortable heat. Detailed installation and operating instructions are included.
Oil stove for workshops, construction trailers, vacation homes.Made of stainless steel sheet, based on the REFLEKS 60M model. In contrast to the REFLEKS ship's stoves, this functional oil stove is only intended for stationary heating purposes.The stove is equipped with the proven TOBY oil regulator for shore operation. Unlike the marine regulator, the TOBY oil regulator for shore operation is not sealed and is therefore not suitable for operation in an inclined position.
Small wall-mounted stove with bowl burner principle: The diesel oil (heating oil) flows from the vat tank through a copper pipe to the stove.The heat output is set manually at the so-called "drip regulator"; the fuel supply must be readjusted during operation. The exhaust gases, and thus also the moisture in the cabin, are led outside through the exhaust pipe (diameter 56 mm). Supplied ready for installation with 3 pieces of 460 mm exhaust pipe, deck duct, exhaust hood, 7-liter stainless steel gravity tank with level indicator (or 12V electric pump, a 24 V DC conversion resistor is included)Automatic ignition fuse and copper piping. Available versions: Completely made of stainless steel or stainless steel with brass front.Both versions are also available in a version without a retractable tank, but with a 12 V electric pump (a 24 V DC conversion resistor is included in the scope of delivery) and a connection pipe to the diesel tank. Dimensions of the reeled tank: 180 x 340 x 290 mm (DxLxH).Heating capacity 2.0 kW, fuel consumption max. approx. 0.25 l/h.
Further development of the proven WALLAS DT diesel hot-air heater, produced in Finland.Laminar flow burner technology and brushless radial fan ensure high warm air output with minimal noise emission, even without a silencer. Pleasant operation for the crew and freedom from disturbance for adjacent berths in the port.The future-oriented Greenboost burners are suitable for automotive diesel (EN 590) and fuels with a higher proportion of renewable fuels and guarantee low diesel consumption with low-emission combustion.Very low power consumption. Effective fresh air circulation for ventilation without heating is possible.Uncomplicated installation of the heaters in the engine room.Long service life, in corrosion-resistant metal housing, 3-year guarantee, worldwide service network. All devices are designed for 12 V on-board voltage.The heater is controlled via an external wired control panel with integrated room thermostat. Functions: stepless manual control, intelligent processor-controlled thermostat control, two-stage boost function, sun switch (switches off automatically on warm days), child lock, LED backlighting.With built-in fuel pump.For 12 V on-board voltage, 0.55-1.0 A .Two air inlets, two hot air outlets - each 75 mm in diameter.See table for dimensions. As the dimensions and connections correspond to the proven heaters of the WALLAS DT series, the replacement of old systems is extremely simple.Scope of delivery: heater, wall bracket with fixing screws, control panel (with 6.0 m connection cable), 4.0 m fuel line with filter, 4.0 m connection cable with 15 A fuse. Material for exhaust, supply and hot air installation is not included.Heating and on-board voltage can be controlled and monitored with the optional remote control type 4430 via SIM card using an app on a smartphone, tablet or PC.To put together the installation material for your heating system, you can also use the online support on the manufacturer's website:https://www.wallas.fi/accessories/units/22gb/index.php
Further development of the proven WALLAS DT diesel hot air heater, produced in Finland.Laminar flow burner technology and brushless radial fan ensure high warm air output with minimal noise emission, even without a silencer. Pleasant operation for the crew and freedom from disturbance for adjacent berths in the harbor.The future-oriented Greenboost burners are suitable for automotive diesel (EN 590) and fuels with a higher proportion of renewable fuels and guarantee low diesel consumption with low-emission combustion.Very low power consumption. Can also be started with very low on-board voltage (from 9.6 V). Effective fresh air circulation for ventilation without heating is possible.Uncomplicated installation of the heaters in the engine room.Long service life, in corrosion-resistant metal housing, 3-year warranty, worldwide service network. The heating is controlled via the wired Advanced control panel, which has Bluetooth and WLAN connectivity (wireless system update and control via smartphone app also possible). The separate wireless Bluetooth room thermostat (extremely simple and flexible installation, multiple thermostats possible) can be placed where the temperature is actually to be measured.Functions: stepless manual control, intelligent processor-controlled thermostat control, two-stage boost function, sun switch (switches off automatically on warm days), child lock, LED backlight.With built-in fuel pump.For 12 V on-board voltage, 0.5-2.2 A .Two air inlets, two hot air outlets D=75mm.See table for dimensions. As the dimensions and connections correspond to the proven heaters of the WALLAS DT series, the replacement of old systems is extremely simple.Scope of delivery: heater, wall bracket with fixing screws, control panel (with 6.0 m connection cable), 4.0 m fuel line with filter, 4.0 m connection cable with 15 A fuse. Material for flue gas, supply and hot air installation is not included.To assemble the installation material for your heating system, please also use the online support on the manufacturer's website: WALLASVIKING AIR installation accessories
New development from the Finnish heating specialist WALLAS: The combined air/water heater VIKING COMBI makes it possible to use 10% to 40% of the heating output to heat domestic hot water (with an optional external boiler), to operate external radiators or underfloor heating. Up to 90% of the heating output can be used to heat air.Laminar flow burner technology and brushless radial fan ensure high warm air output with minimal noise, even without a silencer. Pleasant operation for the crew and freedom from disturbance for adjacent berths in the port.The future-oriented Greenboost burners are suitable for automotive diesel (EN 590) and fuels with a higher proportion of renewable fuels and guarantee low diesel consumption with low-emission combustion.Very low power consumption. Can also be started with very low on-board voltage (from 9.6 V). Effective fresh air circulation for ventilation without heating is possible.Uncomplicated installation of the heaters in the engine room.Long service life, in corrosion-resistant metal housing, 3-year warranty, worldwide service network. The heating is controlled via the wired Advanced control panel, which has Bluetooth and WLAN connectivity (wireless system update and control via smartphone app also possible). The separate wireless Bluetooth room thermostat (extremely simple and flexible installation, multiple thermostats possible) can be placed where the temperature is actually to be measured.Functions: stepless manual control, intelligent processor-controlled thermostat control, two-stage boost function, sun switch (switches off automatically on warm days), child lock, LED backlight.With built-in fuel pump.For 12 V on-board voltage, 0.55-1.0 A .Two air inlets, one hot air outlet D=75mm, connections for water circuit D 19mm.See table for dimensions. As the dimensions and connections correspond to the proven heaters of the WALLAS DT series, replacing old systems is extremely easy.Scope of delivery: heater, wall bracket with fixing screws, control panel (with 6.0 m connection cable), 4.0 m fuel line with filter, 4.0 m connection cable with 15 A fuse.Material for flue gas, supply and hot air installation as well as circulation pump for the hot water circuit are not included.
Powerful 12 V diesel heater.The SPARTAN AIR model offers the latest remote control functions on the market for marine heaters, making operation convenient for everyone. The heater's control panel can be accessed remotely via a mobile app. This makes it easy to switch on and operate the heater from home.A wireless sensor monitors the indoor temperature with high accuracy and ensures an even temperature in the boat.SPARTAN AIR has three inlet openings. In comparison, SPARTAN TWIN has two and many other heaters on the market have only one. Multiple inlet hoses ensure better efficiency and fresher air in the interior. Both models in the SPARTAN series are energy-efficient 4.5 kW heaters - a good choice for medium-sized boats up to 12 m/40 ft.Heating output 1.4 - 4.5 kW3 fresh air inlets3 hot air outletsIntegrated fuel pump12 volts, 0.7-4.5 ampsLaminar flow burner technology and brushless radial fan ensure high warm air output with minimal noise, even without a silencer. Pleasant operation for the crew and freedom from disturbance for adjacent berths in the harbor.The future-oriented Greenboost burners are suitable for automotive diesel (EN 590) and fuels with a higher proportion of renewable fuels and guarantee low diesel consumption with low-emission combustion.Very low power consumption. Can also be started with very low on-board voltage (from 9.6 V).Effective fresh air circulation for ventilation without heating is possibleUncomplicated installation of the heaters in the engine roomLong service life, in corrosion-resistant metal housing3-year guaranteeWorldwide service networkThe heating is controlled via the wired Advanced control panel, which has Bluetooth and WLAN connectivity (wireless system update and control via smartphone app also possible). The separate wireless Bluetooth room thermostat (extremely simple and flexible installation, multiple thermostats possible) can be placed where the temperature is actually to be measured.Functions:stepless manual controlintelligent processor-controlled thermostat controltwo-stage boost functionSun switch (switches off automatically on warm days)Child safety lockLED backlighting.See table for dimensions. As the dimensions and connections correspond to the proven heaters of the WALLAS DT series, replacing old systems is very easy.Scope of delivery:(Material for the installation of flue gas, supply air and hot air pipes is not included, as this must be adapted individually for each ship)HeaterWall bracket with fixing screwsControl panel (with 6.0 m connection cable)Wireless Bluetooth room thermostat4.0 m fuel line with fuel filter4.0 m connection cable with 15 A fuse
The most powerful WALLAS diesel heaterAs one of the most powerful models, the WALLAS SPARTAN TWIN offers the most advanced control functions on the market for marine heaters, ensuring maximum comfort and versatility.The heating control panel can be accessed remotely via the WALLAS app. This makes it easy to switch on and operate the heating from anywhere.The wireless sensor monitors the room temperature with high accuracy and ensures even temperature stability and maximum comfort.An important feature of the SPARTAN TWIN, which contributes to the optimal use of its application, are the two fresh air inlets and two hot air outlets. In comparison, the Spartan Air has three inlets and three outlets.Multiple supply air sources ensure better efficiency and fresher air in the interior. Both the SPARTAN TWIN and SPARTAN AIR heaters have a rated output of 4.5 kW and are an excellent choice for boats from 9 to 12 meters (29-40 ft).Heating output 1.4 - 4.5 kW2 fresh air inlets2 hot air outletsIntegrated fuel pump12 volts, 0.7-4.5 ampsLaminar flow burner technology and brushless radial fan ensure high warm air output with minimal noise, even without a silencer. Pleasant operation for the crew and freedom from disturbance for adjacent berths in the harbor.The future-oriented Greenboost burners are suitable for automotive diesel (EN 590) and fuels with a higher proportion of renewable fuels and guarantee low diesel consumption with low-emission combustion.Very low power consumption. Can also be started with very low on-board voltage (from 9.6 V).Effective fresh air circulation for ventilation without heating is possibleUncomplicated installation of the heaters in the engine roomLong service life, in corrosion-resistant metal housing3-year guaranteeWorldwide service networkThe heating is controlled via the wired control panel, which has Bluetooth and WLAN connectivity (wireless system update and control via WALLAS app also possible). The separate wireless Bluetooth room thermostat (extremely simple and flexible installation, multiple thermostats possible) can be placed where the temperature is actually to be measured.Functions:stepless manual controlintelligent processor-controlled thermostat controltwo-stage boost functionSun switch (switches off automatically on warm days)Child safety lockLED backlighting.See table for dimensions. As the dimensions and connections correspond to the proven heaters of the WALLAS DT series, replacing old systems is very easy.Scope of delivery:(Material for the installation of flue gas, supply air and hot air pipes is not included, as this must be adapted individually for each ship)HeaterWall bracket with fixing screwsControl panel (with 6.0 m connection cable)Wireless Bluetooth room thermostat4.0 m fuel line with fuel filter4.0 m connection cable with 15 A fuse
REFLEKS modifies this beautiful cast iron stove type 1010 from the Danish stove foundry MORSOE with its proven bowl burner and the TOBY oil regulator into a ship's stove that is operated with diesel oil.With sling rail made of polished brass tube.The flame can be easily observed through the large window, pleasantly dry radiant heat due to the fireclay lining of the combustion chamber. The surface is matt black.Model REFO 6000.Exhaust pipe outlet 120 mm, optionally at the top or rear. Heat output 1.4-6.0 kW,consumption 0.2-0.9 l/h,for room sizes from 50-80 m³.
