High-performance bilge pump, available in various sizes for 12V or 24V systems. Discharge head up to 3 m.The snap-off plastic housing can be opened easily for maintenance and cleaning. Low power requirements.Stainless-steel shaft with a high-quality seal.Built in Italy by MARCO.
Powerful submersible pump from RULE. The pump is made of sturdy plastic and is ideal for smaller boats due to its light and compact nature.The motor is fully enclosed and runs very quietly. The shafts can not rust and are specially sealed against water penetration.The inlet strainer of the pump can be easily removed to clean the pump. The check valve prevents water from flowing back into the bilge, and the ventilated housing optimally prevents air pockets.A thermal shutdown prevents overheating and protects the pump.Also available as RULE AUTOMATIC (RA) automatic pumps. See under similar products.
The proven bilgepump from the US manufacturer RULE. Plastic housing with easily removable sieve baseplate. Quiet-running and fully encapsulated motor. Also made as an automatic pump: Type: RULE-AUTOMATIC (RA) works through an automatic microprocessor that checks if there is water in the bilge by briefly running the pump every 150 seconds (without a mechanical switch). Limited power requirements for the test runs: Only approx. 0.2-0.5 Ah per day.
WHALE GULPER type 220: Electric membrane pump for pumping the bilge or emptying the head or holding tank (grey water pump). Self-priming. Suction lift max. 3 m, dicharge head max. 3 m, combined suction lift / discharge head max. 4m.Odorless running, vibration absorbing rubber feet.Universal installation due to swiveling pump heads.For tube 19mm. Weight 1.5 kg. Dimensions: L x W x H = 273 x 111 x 117 mm. Spare-parts sets available.
The proven automatic bilge pump, from US manufacturer RULE.Plastic housing with easily removable sieve baseplate.Quiet and fully encapsulated motor, stainless axis.Can be used as an automatic pump:Type RULE-MATE (RM) is controlled with an integrated electronic switch. Supplied with straight hose nozzles for 25 and 28 mm.
Flat, powerful bilge pump for tight spaces with freely adjustable hose outlet (vertical/horizontal) for 3 different hose diameters (19, 25 and 28 mm). All hose nozzles have lip check valves, the motor unit is removable for cleaning, maximum pumping height is 3.4 m.Pumping capacity: 3373 l/h at the same level.2400 l/h at 1 m height difference (1 mWS).Available as standard pump (type LP900D) or as automatic pump (type LP900S) with integrated sensor switch.The sensor has 3 switching modes: in mode "L" the pump switches on at a water height of 33 mm, in mode "H" at 50 mm, in mode "Time" the pump checks every 150 seconds by a short start if water is present and then pumps until the bilge is empty.
Very powerful, self-priming electrical diaphragm pump with reliable industrial motor.This Rheinstrom diaphragm pump has been found to be very reliable over many years. It can be used as a bilge pump, a grey water pump and a delivery pump.Constant delivery rate, high safety against clogging, very good cleaning possibilities.Made of hard-wearing materials, the body is made of seawater-proof cast bronze.Fast and easy cleaning and maintenance and direct access to the valves are obtained by simply opening the lid of the pump. The discharge and suction side may be altered.Technical dataPump performance: 40 l/minDelivery head: 10 mSuction height: 3,5 mConnection: 38 mm hose connectionMotor: 110 WWeight: 9,5 kgA repair kit is available.
Submersible bilgepump with strong permanent magnet motor and special shaft seals.The outer cover can be removed for inspection.Shaft of rust-free steel.These pumps are only partially protected against dry-running, so the installation of the optional floating or sensor switch is recommended.
WHALE GULPER type 320: Electric membrane pump for pumping the bilge or pumping out the head or holding tank (grey water pump). Self-priming. Suction lift max. 3m, dicharge head max. 3 m, combined suction lift / discharge head max. 4m.Odorless running, vibration absorbing rubber feet.Universal installation due to swiveling pump heads.A variable tube adaptor connects the GULPER 320 to 19mm or 25mm tube. Weight 1.6 kg. Dimensions: L x W x H = 273 x 111 x 117 mm. Spare-parts sets available.
Extremely low-profile, submersible pump with good power, by the renowned pump manufacturer WHALE, which can also be placed between frames and floor boards.Equipped with a built in, maintenance free 'electric field sensor' as integrated float switch, removable sieve and non-return valve.Outflow hose adjustable from horizontal to vertical.Versions: SUPERSUB SMART 5212 has a max. pump output of 40 l/min and 34 l/min at 1 meter height. SUPERSUB SMART 1212 and 1224 have a pump output of 66 l/min and 47 l/min at 1 meter height.
Extremely low-profile, submersible pump with good power, by the renowned pump manufacturer WHALE, which can also be placed between frames and floor boards.Removable sieve, outflow hose adjustable from horizontal to vertical.Article 1441-111 comes with a non-return valve. Versions:SUPERSUB 5012 has a max. pump output of 32 l/min and 25 l/min at 1 meter height. , SUPERSUB 1012 has a max. pump output of 66 l/min and 47 l/min at 1 meter height.Also available in the WHALE SUPERSUB SMART version with automatic sensor switch.
Powerful impeller pump with bronze pump head and impeller made of nitrile rubber (oil-resistant), dry self-priming up to 1.20 m. Developed for pumping bilge water. Dry-running protection up to 20 minutes. Capacity 32 l/min at 3 m (0.3 bar) or 27 l/m at 5 m (0.5 bar), suitable for continuous operation.Dimensions 190x120x80 mm.Versions for 12V or 24V on-board voltage are available. Connection 3/4" (inside).