Paint & conservation

Swedish brown wood tar. Made by the dry distillation of coniferous wood.Works well as a natural preservation for wood and natural-fiber rope.May be thinned with turpentine, linseed oil or petroleum.For wood protection, we recommend up to 5% Sikkativ (check "Suitable items") as a supplementary drying agent.

Blown (at 120íC) linseed oil, with a cobalt proportion of 0.006%,that deeply and thoroughly seeps into the wood and air-dries in approximately 24 to 36 hours.

Made from flaxseed oil; intended for treating wood and making paints.Pure, natural product, without chemical additives.

Labsale (tar) is a special mixture of wood tar and boiled linseed oil.Traditionally, this product was used to protect natural-fiber rope and standing rigging on board.Our Labsale is mixed especially for us according to a proven (secret) recipe.

Pure Chinese wood oil for the conservation of wood and for the making of inartificial impregnations (e.g. Danish Oil).

Additive for linseed oil and Swedish tar, to ensure quicker drying of each coat.Max. 1% is required for linseed oil varnishes; max. 5% for Swedish tar.

Technical white oil is a highly purified mineral oil. It's odorless, durable and without synthetic additives. This product is exceptionally proven for protecting woods in the interior and protecting varnish outside.

OWATROL DEKS OLJE D1 is a low-viscosity, transparent oil that is ideal for saturating wood, especially hardwoods and tropical woods. Due to its enormous penetrating capacity, it penetrates deep into the wood and displaces any moisture and air present. On the one hand, complete saturation prevents solid wood from working so that it no longer swells. On the other hand, the oil provides preventative protection against fungal and mold infestation. In the case of porous wood, treatment with D1 facilitates subsequent painting, as saturated wood absorbs less varnish or paint.OWATROL D1 can be applied to new, untreated wood or to wood that has already been weathered (with appropriate preparation). As a sole preservative, a permanently elastic, breathable, silky matt surface is achieved (e.g. for non-slip decks). OWATROL DEKS OLJE D2 is recommended as a film-forming further treatment. OWATROL D1 can also be painted over with 1-component primers and alkyd paints.Application: The product is applied in several coats until the wood is saturated. Then wait 15-20 minutes to allow the oil to soak in. Do not allow the oil to dry between coats, but work wet on wet. After the last coat, the surface should be wiped with a clean cloth after the waiting time to avoid the formation of a film.Important: To saturate wood in underwater areas, ensure that the wood is coated with a waterproof blocking primer (silver primer, CR primer). A recoating interval of at least one week (at 20°C) should be maintained between OWATROL D1 and primer, and correspondingly longer at cooler temperatures. It is also important to ensure that after the last coat of OWATROL&nbspTechnical DataSubstrate: All wood types, including dense and oily hardwoods (e.g. teak, mahogany),Application area: interior and exteriorSurface preparation:Remove old coatings completelySand wood dry with 120 grit and clean (e.g. with denatured alcohol)For decks: sand with 40 grit, brush in grain direction using brass brush for slip resistanceTopcoat: Above water: OWATROL DEKS OLJE D2, 1component-PUR varnishes, alkyd-based coatings (test first); Below water: chlorinated rubber primer + antifoulingCoverage: 1–4 m²/l (initial saturation), 8–12 m²/l (maintenance)Thinner: None Application method: Flat brush, mohair roller, spray deviceDrying times at 20 °C: Fully cured after 3 daysFurther information on applying this product can be found in the technical data sheet under "Downloads".

IMP IMPREGNATING OIL is a transparent wood priming oil made from a drying alkyd resin oil. It is used for the care and preservation of dimensionally stable wooden components above the waterline in indoor and outdoor areas.Thanks to its excellent penetration properties, it acts preventively against rot and fungal infestation when saturating the wood, as air and moisture are displaced. It dries quickly, is vapor-permeable and water-repellent. Suitable as a saturating primer for further coatings such as BENAR oils and other single-component paints. For sole treatment (matte surface) of spars and masts, the "wet-on-wet" application is recommended until the wood is fully saturated. Suitable for all types of wood.Application: The product is ready to use and should not be diluted. Stir well before use. Application can be done with a brush or roller. The oil is applied wet-on-wet until the wood pores are fully saturated. Material that has not penetrated must be removed immediately with a clean, lint-free cloth. Clean tools with white spirit.Technical DataField of application: Care and preservation agent for wood above the waterline (indoor and outdoor)Substrate: Clean, dry, free of grease and dust; for new tropical woodsCoverage: approx. 3–6 m²/l (theoretical, depending on absorbency)Thinning: No spray dilution intendedApplication method: Brush, rollerDrying times (at 20 °C): Dust-dry after 5 hrs, re-coatable after at least 24 hrs (max. 3 months), fully loadable after 2 days

OWATROL DEKS OLJE D2 is a film-forming, high-gloss oil varnish that is applied as a top coat to wood surfaces treated with OWATROL DEKS OLJE D1.The coating forms a resistant, elastic varnish film that does not crack or flake off. Highly effective UV protection pigments ensure long-lasting protection. Particularly suitable for use on tropical hardwoods that are difficult to paint. Only use above water on all wooden surfaces that are not constantly exposed to water.Application: Apply three to six coats at intervals of at least 12 hours at 20° C. Do not sand between coats. Wipe up drips and runs immediately after application, as dried D2 oil is very difficult to remove completely. Allow to dry for at least three to four days, better a week before putting any load or stress on the surface. Technical DataApplication area: Wooden surfaces above waterline, interior/exteriorSubstrate: soft and hard woodsPre-treatment: Prime with OWATROL DEKS OLJE D.1; sand and degrease surfaceApplication: brush, rollerCoverage: approx. 12 m²/lThinner: noneDrying (20 °C): dust dry: 6 hrs, recoatable: 12 hrs, Loadable: 1 weekIngredients: alkyd-urethane resinsApplication temperature: 8°C to 35°CFurther information can be found in the technical data sheet under “Downloads”. 

A highly effective pre-coating oil that protects, beautifies and hardens wood. LE TONKINOIS BIO IMPRESSION is ideal for pre-treatment before varnishing, as it penetrates deep into the wood and, due to its saturation, unifies the absorption behavior of the wood surface. Made from pure natural oils (linseed oil, castor oil, palm oil) and free from harmful substances and solvents. The oil dries quickly, is abrasion-resistant after drying and provides a good base for further surface coating with varnishes such as LE TONKINOIS Vernis or Marine No.1.Technical DataApplication area: Interior/exterior wood: windows, doors, fences, cladding, floorsSubstrate: sanded, clean, dry, max. 15% moistureApplication: brush, flat brushCoverage: avg. 20 m²/l; 30–50 ml/m² eepending on materialThinner: noneDrying (20 °C): dust dry 6–8 hrs, recoatable after 12 hrsIngredients: linseed oil, tung oil, natural resins, isoaliphaticsFurther information can be found in the technical data sheet under "Downloads".

OWATROL OIL, which is based on natural oils and has exceptionally good penetration properties, is the basic product for many applications.It is three times wetter than water, i.e. it even creeps upwards. On rusty metal, it creeps deep into the rust pores and displaces the air and moisture (i.e. the actual cause of corrosion) even from inaccessible areas. After drying (24 hours at 20°C), the leaf rust can be removed more easily and the soaked residual rust is consolidated, preserved, sealed and can be painted with all turpentine substitute thinnable paints.OWATROL-OIL is also ideal as an additive (color additive) for 1-component paints. Instead of using turpentine substitute as a thinner, it significantly improves the coating and flow properties and ensures optimized adhesion without compromising the quality of the paint. On the contrary, the addition of 10-15% OWATROL OIL makes paints and varnishes even more porous and durable on the surface.OWATROL spray is suitable for minor touch-ups.Technical dataSubstrates: Rusty and bare metals (iron, steel, aluminum), new and weathered woodPre-treatment: depending on the material: remove loose rust, non-adherent old paint, oil and grease

Penetrating oil based on natural oils, which is used as an additive to improve the flow properties of conventional and semi-synthetic paints. It reduces visible brush strokes, impregnates wood and has a rust-inhibiting effect on steel by penetrating deep into the substrate. This means that a favorable result can be achieved even under difficult conditions.

Deep-penetrating wood protection oil for pre-treatment of raw wood. RYLARD IMPREGNANTE serves both as a natural final treatment with an open-pored appearance and as a primer for further coatings with RYLARD varnishes. The product effectively protects the wood from natural damage such as fungi, mold, or insect infestation and is suitable for both indoor and outdoor use.Application: The surface should be clean, dry, and free of dust; old varnish layers must be removed beforehand. Two coats are required, at intervals of at least 12 hours. Application is done with a brush or spray gun. After the final coat, the desired topcoat can be applied after another 12 hours. Also suitable for wooden surfaces that have been stripped by sanding or hot air.RYLARD VarnishesThe Italian ship and yacht paint manufacturer BRAVA from Genoa offers with its RYLARD brand a range of traditional yacht varnishes, whose original formula was developed for the emerging yachting sport in the 19th century and is referred to on many classic yachts as the “Yachtman's Mirror.”Technical DataApplication area: Protection and priming for raw wood indoors and outdoorsSurface: Clean, dry, untreated woodCoverage: 15–20 m²/lThinning: White spirit substituteApplication method: Brushing or sprayingDrying times (at 20 °C): Dust-dry after 6 h, recoatable after 12 hFor more information on application, please refer to the technical data sheet under 'Downloads'.

OWATROL OIL, which is based on natural oils and has exceptionally good penetration properties, is the basic product for many applications.It is three times wetter than water, i.e. it even creeps upwards. On rusty metal, it creeps deep into the rust pores and displaces the air and moisture (i.e. the actual cause of corrosion) even from inaccessible areas. After drying, the leaf rust can be removed more easily and the soaked residual rust is consolidated, preserved and sealed for the long term and can be painted with all turpentine-substitute thinnable paints.For use on larger surfaces or as a paint additive, OWATROL is suitable for painting from the can.Technical dataSubstrates: Rusty and bare metals (iron, steel, aluminum), new and weathered woodPre-treatment: depending on the material: remove loose rust, non-adherent old paint, oil and grease

Universal surface impregnation for many absorbent surfaces such as sails, tarpaulins or boat cushions, as well as transparent protection for natural stone and wood surfaces. The product does not build up, but is absorbed into the surface, is invisible and does not change the color of the treated surfaces. OMNISIDE INNOPERL is highly water, oil and dirt repellent (hydrophobic and oleophobic) and the treatment creates surfaces that are easy to clean.Made on the basis of fluoropolymers, solvent- and silicone-free, therefore suitable for indoor use. NOT SUITABLE for: Application on lime putty techniques in the facade area, leather.Application: The product can be applied with a brush, fur roller, cloth or pressure pump sprayer. After drying, there must be a pronounced water-repellent effect, otherwise repeat the application.Technical DataApplication area: absorbent and low-absorbent substrates, natural stone, plaster, exposed concrete, textiles (e.g. awnings, covers, cushions)Substrate: clean, dry, grease-free, not for constant water exposureApplication: brush, roller, cloth, pump sprayer, immersion methodCoverage: approx. 10 m²/lThinner: water, up to 1:2 dilution possibleApplication temperature: +10 °C to max. +25 °C (avoid direct sunlight)Drying (20 °C): dry after approx. 2 hrs, fully resistant after 24 hrsFurther information on application can be found in the Technical Data Sheet under "Downloads".

OWATROL AQUADECKS is a water-based wood oil for indoor and outdoor use, used for impregnating and protecting soft and hardwoods. It penetrates deeply into the wood and provides a matte, open-pored surface that preserves the natural appearance. The oil is particularly suitable for decks, gangways, walkways, and similar applications on or onboard. It protects the wood from moisture and UV radiation and can be used on new, weathered, or already grayed wood.Application: For untreated wood, sand the wood surface if necessary, dust off, degrease or clean (see data sheet). Treat weathered wood with OWATROL NET-TROL (Art.No. 2508-001). Old coatings - except AQUADECKS coatings - must be removed. Application is done in two wet-on-wet coats without intermediate sanding. Wait 15-20 minutes between coats until the product is absorbed by the wood. After the second application, distribute or wipe off any excess product with a clean cloth after 20 minutes to avoid film formation and associated weakening of the properties. It can be applied with a brush, roller, or spray device. Tools can be cleaned afterwards with water and soap.Technical DataApplication area: Indoors and outdoors, e.g. terraces, teak decks, garden furnitureSubstrate: Hard and soft wood, tropical woods such as teak, ipe, bangkirai, merantiApplication: Brush, roller, spray deviceCoverage: approx. 10-12 m²/l (depending on wood type and absorbency)Thinning: noneApplication temperature: +10 °C to +30 °CDrying (20 °C): recoatable after 15–30 min., fully dried after 24–48 hrs.Further information on application can be found in the Technical Data Sheet under "Downloads".

Preventive, open-pored wood preservative against fungal decay and insect attacks of timber in the interior and outdoors as well as wood in humidors.Also suited for the restoration (solidification) of old timberPermeable for water vapour .Effective by obfuscation of the wood for vermin. Rubber gloves should be carried when applying.A recognised respiratory equipment should be carried when using a spray diffuser.Do not sand with steel wool, since the sanding dust can lead to black staining. The biopin Vertriebs GmbH produces innovative natural paints already in the fourth generation with the technical facilities of the present. The company manufactures wholesome products on the basis of natural raw materials.

HEMPEL'S WOOD IMPREG is a clear alkyd oil with great penetration properties. It serves as a primer for hardwoods indoors and outdoors above the waterline. The oil penetrates deeply into the wood and ensures an even saturation of the substrate.Application: The surface must be clean, dry, and free of grease; the wood moisture content must not exceed 16%. HEMPEL'S WOOD IMPREG is applied with a brush in 2–4 wet-on-wet coats. Excess oil should be removed with a lint-free cloth to avoid film formation. Once dry, it can be overcoated with suitable Hempel paints. Thinning and cleaning should be done with HEMPEL'S THINNER 811 (Item No. 2577-026).Technical DataArea of application: Primer for wood saturation, indoors and outdoors above the waterlineSubstrate: Clean, dry, grease-freeCoverage: approx. 13 m²/l (depending on the porosity of the wood)Thinning: HEMPEL'S THINNER 811Application method: BrushDrying times (at 20 °C): Touch dry after approx. 6 h, re-coatable after full penetrationDurability: Until overcoated with paint; not a standalone topcoatFurther processing information can be found in the Technical Data Sheet under 'Downloads'.

"TONKI" - the classic! Glossy, clear varnish oil for wood and metal. The formulation of LE TONKINOIS varnish oil is based on a special formula in which high-quality linseed oil and Chinese wood oil (tung oil) are cooked together. This creates a natural product without chemical additives. The varnish oil is suitable for indoor and outdoor use as well as for application under extreme weather conditions. It forms a resistant, elastic protective film with high UV resistance and highlights the natural grain of the wood.Application: LE TONKINOIS VARNISH is applied to untreated or cleanly sanded wood. Application is done with a brush or roller; for spray application, it can be diluted up to max. 10% with the appropriate LE TONKINOIS thinner. Only one thin coat should be applied per day. Stir well before use, do not apply below 12 °C.Technical DataArea of application: Wood and degreased metals indoors and outdoors, also under extreme weather conditionsSubstrate: Untreated wood, wood-based materials, limited use on corkCoverage: 20 m²/l Thinning: Max. 5–10% with LE TONKINOIS thinnerApplication method: Brush, flat brush, sprayingDrying times (at 20 °C): Dust dry after 6–8 h, reworkable after approx. 24 h, walkable after 3 days (with 2–3 coats)Further information on application can be found in the technical data sheet under 'Downloads'.

"TONKI No.1" - the classic for sunny sailing areas. LE TONKINOIS MARINE NO.1 is a glossy, clear oil varnish specially developed for wooden surfaces in maritime environments. It is approved by the French Navy as a ship varnish and is suitable for both interior and exterior use. When applied properly, the product offers high weather and UV resistance, and is abrasion and impact resistant. Made from TONKINOIS varnish oil, but slightly thinner and faster-drying. The formulation is free from chemical additives, considered child-safe (according to DIN EN 71-3), and enables long-lasting surface protection with multiple applications.ApplicationMarine No. 1 is applied to untreated or appropriately pretreated wood. Application is done using a brush, flat brush, or by spraying. The coats are applied thinly, with only one layer per day. For exterior areas, six to ten coats are recommended; for interior areas, half is sufficient. A primer with Bio Impression is recommended for untreated or highly absorbent wood. The application temperature should be at least 12 °C.Technical DataApplication area: Wooden surfaces indoors and outdoors, seawater and UV resistantSubstrate: Untreated wood, wood-based materials, conditionally corkPrimer: Bio ImpressionCoverage: 20 m²/l per coatThinning: Use undiluted; when spraying max. 10% Le Tonkinois thinnerApplication method: Brushing, rolling, sprayingDrying times (at 20 °C): Dust-dry after 5–8 h, recoatable after at least 24 hFurther information on application can be found in the Technical Data Sheet under 'Downloads'.

Traditional oil varnish based on wood oil and alkyd resin for coating oily hardwoods such as teak and American softwoods. EPIFANES hardwood varnish oil serves as an alternative to pure oil systems and forms a grease and oil regulating clear varnish system in up to five coats.With a layer structure of less than five layers, the varnish oil still remains breathable. With more coats, the wood is completely sealed. Can be used for coating solid wood and plywood indoors and outdoors above the waterline, as well as for reworking existing one- and two-component lacquer systems.Application: Do not use the product below 8°C and avoid direct sunlight or strong wind. Apply the hardwood varnish oil with a brush. Do not apply wet on wet and avoid too thick layers to prevent drying problems, runs or craters. Intermediate sanding after the first coat after 24 hours by hand with a 280-320 grit paper, no intermediate sanding is necessary between subsequent coats as long as the drying times are observed. For oily woods, the manufacturer recommends a layer build-up of 5 coats, for other woods a layer build-up of 7 coats.&nbsp

Deeply penetrating natural oil, boiled from linseed oil, wood oil and hard spruce resin. Isoparaffinic serves as a solvent. BIO PIN boat oil dries to a high gloss and because of its composition is very long lasting, as well as water-, UV- and weather-resistant. It possesses a long-lasting elasticity, won't crack and no water can creep under. It is recommended as a base for BIO PIN.Coverage: approx. 12 m.sq./l.

Clear varnish oil with a satin finish, specially suited for tropical woods, made from wood oil, phenol, and alkyd resin. EPIFANES Woodfinish Matte is suitable as a matte topcoat over a varnish build-up of EPIFANES Hardwood Varnish Oil Gloss or EPIFANES Clear Varnish. The varnish oil has very good resistance to solvents, alcohol, and household cleaners, as well as built-in UV protection.Application: The product can be applied with a high-quality brush to a previously sanded, clean surface. 1-2 coats are recommended, and no sanding between coats is necessary within 24-72 hours.Technical DataApplication area: Matte varnish oil finishSubstrate: clean, sanded clear coat systems such as EPIFANES Clear Varnish (Art.No. 2050-001) or Hardwood Varnish Oil Gloss (Art.No. 2051-001)Coverage: Approx. 13 m²/L at 35 µm dry film thicknessColor: clear, amberThinning: Brush: Epifanes Paint Thinner (Art.No. 2059-001), Spray: Epifanes 1-C Spray Thinner (Art.No. 2059-110)Application method: Brush, roller or spray gun (professional users)Drying times (at 20 °C): Dust dry after 3 hrs, sandable after 24 hrs, recoatable after 24 hrsFurther information on application can be found in the Technical Data Sheet under 'Downloads'.

BENAR UVR is a high-gloss wood oil based on long oil alkyd resin with an additional red-brown pigmented UV filter for outdoor use. It was specially developed for tropical and European hardwoods such as teak, mahogany or oak and forms an elastic, breathable protective film with very good weather resistance. The high vapor permeability prevents moisture from being trapped under the varnish film and thus prevents rotting. The high elasticity &nbsp

LE TONKINOIS Yacht Oil Stain is a plant oil-based, intensely colored wood pre-treatment for hardwood surfaces indoors and outdoors. The stain penetrates deeply into the wood and creates a uniform coloration with a pleasant feel. It is resistant to dirt and water-repellent, and the pigmentation increases UV protection. In boatbuilding it is suitable for matching the color of wooden surfaces on decks, superstructures and other heavily used surfaces. For adequate protection, a subsequent protective coating with LE TONKINOIS Vernis or Marine No.1 is recommended.Application: The surface must be dust- and grease-free and clean; the wood moisture should not exceed 15%. The stain is applied undiluted with a brush or roller to untreated wood. After a short exposure time, the excess is evenly distributed and removed with a lint-free cloth. It is recommended to create a test area beforehand. The processing temperature should be at least 12 °C. Walkability is achieved after three days with 2–3 coats.Technical DataField of application: Indoor and outdoor, e.g., boat decks, superstructures, wooden floorsSubstrate: Untreated wood, wood-based materialsCoverage: 35–50 ml/m² (depending on type of wood)Application method: Brushing with brush or rollerDrying times (at 20 °C): Dust-dry after 6–8 h, re-coatable after 12 h, walkable after 3 daysFor more information on processing, please refer to the technical data sheet under 'Downloads'.

Transparent protective and maintenance oil with UV protection for all exterior wood, particularly suitable for teak decks. OWATROL DECK SEALER is an air-drying natural oil with properties similar to OWATROL TEXTROL Transparent. Due to its excellent penetration properties, it penetrates deep into the wood and thus protects against weathering from the inside out. It is non-film-forming and open to diffusion, so that moisture exchange is guaranteed. The transparent oil does not change the original shade of the wood, but intensifies the shade as if the surface were wet.The product is leached out by weathering over time, so regular reworking in combination with DECK CLEANER is recommended, depending on the weather conditions.Technical dataArea of application: Exterior wood, e.g. decks, furniture, masts, walkwaysSurface: clean, dry, grease-free, sand if necessaryApplication: cloth, brush, fur roller, sprayerCoverage: approx. 5 m²/l (initial treatment), approx. 10 m²/l (maintenance)Dilution: noneApplication temperature: 5 °C to max. 35 °C (not in direct sunlight)Drying time (20 °C): 24-48 hoursFurther information on processing can be found in the technical data sheet under "Downloads".

Current delivery notice: BENAR OIL CLEAR is currently not available. Please switch to alternative products such as BENAR UVR (2092-750) or varnish oils from OWATROL, LE TONKINOIS or EPIFANES.BENAR GLOSS is a high-gloss wood oil based on long-oil alkyd resin for the care and preservation of tropical and domestic hardwoods. The product forms an elastic, breathable protective film with good water vapor permeability and is suitable for use on surfaces with low UV exposure indoors and outdoors. The amber-colored varnish oil penetrates deeply into the wood and provides long-lasting protection against weathering. The high elasticity of the varnish oil additionally prevents flaking or chipping. This makes BENAR oil also very well suited for "working" solid woods. Application: Apply with a brush to clean, dry, grease-free surfaces. For highly absorbent and fungus-prone woods, a prior impregnation with IMP Impregnation Oil (Art.No. 2090-001) is recommended. Apply the first coat thinned (max. 15% white spirit substitute), further coats unthinned. Then apply at least three more unthinned coats outdoors (three coats are sufficient indoors). If a matte surface is desired, BENAR OIL MATT (Art.No. 2094-750) must be applied as the final coat. For soft and light-sensitive woods and for horizontal surfaces exposed to strong sunlight outdoors, we recommend BENAR OIL UVR (Art.No. 2092-003).Technical DataApplication area: Wood protection oil for indoor and outdoor useSubstrate: Clean, dry, load-bearing; max. 18% wood moisturePrimer: IMP Impregnation OilCoverage: 14–16 m²/l per coatThinning: White spirit substitute (only for first coat)Application method: Brush or airless (professional users)Drying times (at 23 °C): Dust-dry after approx. 6 hrs, recoatable after 24 hrsSafety note: Always use personal protective equipment during application. Further information on application can be found in the Technical Data Sheet under 'Downloads'.The shipping of this product is only possible in accordance with the Chemicals Prohibition Ordinance to resellers, professional users and public research and educational institutions.Do you belong to this customer group? Then send us your request here. We will gladly prepare a delivery offer for you.For private users, delivery is only possible in our Hamburg store against proof of use.

BENAR MATT is a clear wood oil based on long-oil alkyd resin for achieving a matte finish as a final coat on other BENAR products such as BENAR GLOSS (Art.No.2091-003). The product forms a matte, breathable protective film with good water vapor permeability and is suitable for use on surfaces with little UV exposure, both indoors and outdoors. Application: Apply with a brush on clean, dry, grease-free surfaces. Technical DataArea of application: matte wood protection oil for indoor and outdoor useSubstrate: surfaces coated with BENARCoverage: 14-16 m²/l per coatThinning: noneApplication method: brush or airless (professional users)Drying times (at 23 °C): dust-dry after approx. 6 hrs, recoatable after 24 hrsSafety Note: Always use personal protective equipment during application. For more information on application, please refer to the Technical Data Sheet under 'Downloads'.The shipment of this product is only possible to resellers, professional users, and public research and educational institutions in accordance with the Chemicals Prohibition Ordinance.Are you part of this customer group? Then send us your inquiry here. We will be happy to provide you with a delivery offer.For private users, sale is only possible in our retail store in Hamburg upon proof of intended use.

Protective and maintenance oil with high penetration capacity for all interior wood. OWATROL INTERIÖL is colourless and produces a silky matt surface that emphasizes the natural grain of the wood. A glossy finish can be achieved by applying a further coat 24 hours after the wood is saturated.Stabilizes raw, untreated wood from the inside out and reduces swelling and shrinkage due to saturation. Protects physically (moisture cannot penetrate) and thus prevents the infestation of mold and fungal infestation, completely without chemical fungal protection or pesticides. Application: Apply the oil wet-on-wet without intermediate drying (interval approx. 30 to 60 minutes) until the wood is saturated. Do not allow to dry between coats. According to the manufacturer, 4-6 coats are recommended when treating wooden floors. One hour after the last coat, the surface should be wiped with a clean, lint-free cloth to distribute and absorb excess material. Otherwise the surface may remain sticky. If this interval is exceeded, excess product can be removed mechanically by sanding or with a suitable paint remover (OWATROL DILUNETT, Art. No. 2511-001). Very absorbent woods should be treated again after 12 hours at the earliest. To achieve a perfect finish, the surface can be sanded with 120 grit sandpaper and INTERIÖL as a sanding liquid.Technical DataApplication area: Interior wood, e.g. furniture, floors, panels, kitchen countertopsSubstrate: bare, clean, dry, grease-free, soundApplication: soft flat brush, mohair roller, fine spray deviceCoverage: approx. 8-12 m²/l Thinner: noneApplication temperature: +8 °C to max. +35 °CDrying (20 °C): dust dry after 4–5 hrs, fully dry after 12–72 hrs.Further information on application can be found in the Technical Data Sheet under "Downloads".

Transparent protective and maintenance oil with UV protection for all exterior wood.OWATROL TEXTROL RUSTIC is an air-drying wood oil that penetrates deep into the wood and protects it from the inside out. It does not form a layer on the surface of the wood and therefore cannot flake off. Provides long-lasting protection against moisture, weathering and UV radiation and can be used on both horizontal and vertical surfaces. The oak color pigmentation provides additional protection against UV rays and graying.Application: Waxed or varnished wood should be treated with OWATROL NET-TROL (2508-001) before application. Also wood containing tannic acid such as oak should be cleaned beforehand and treated with NET-TROL. Apply two coats wet-on-wet on the bare wood at intervals of 15-30 minutes. A third coat is recommended for particularly dry or porous wood surfaces. Wait 30-60 minutes after applying the last coat and then wipe off any excess material with a clean cotton cloth to prevent a film from forming. Otherwise the surface may remain sticky or stained. Technical DataApplication area: Exterior wood, e.g. decking, cladding, furniture, fencesSubstrate: bare, clean, grease-free, dryApplication: brush, rollerCoverage: approx. 10–12 m²/lThinner: noneApplication temperature: min. +5 °C to max. +25 °C (avoid direct sunlight)Drying (20 °C): 24–48 hrsFurther information on application can be found in the Technical Data Sheet under "Downloads".

The proven classic among one-component clear coats: EPIFANES boat varnish . High gloss, easy to apply and very durable. This air-drying varnish based on wood oil, phenolic resin and alkyd resin is suitable for use on solid wood and plywood indoors and outdoors above the waterline. The varnish forms a transparent amber-colored, gloss-stable protective film with very good weather and UV resistance. Its high elasticity prevents cracking on working wood. Suitable for coating raw wood (mahogany, meranti, Oregon pine) and plywood above the waterline&nbsp

EPIFANES PP Varnish EXTRA is a fast-drying, two-component clear varnish based on alkyd resin and isocyanate with a high solids content and excellent chemical and mechanical resistance. The high-gloss varnish is suitable for interior and exterior use above the waterline and can also be used as a sealer on oily woods such as teak, iroko, or Oregon pine. It forms an elastic, filling protective film with high impact resistance, good gloss retention, and excellent adhesion to solid wood, veneer, and plywood. For optimal UV protection, a finishing coat is recommended.Application: The substrate should be sanded, dust- and grease-free, with a maximum wood moisture content of 15%. Mix both components at a 1:1 volume ratio and apply with a brush or spray gun after a 15-minute induction time. The first coat can be thinned with 5–10% EPIFANES THINNER FOR 2-C VARNISH PP. For exterior use, at least four coats are required. For optimal UV protection, a final topcoat with a 1-C varnish such as EPIFANES Clear Varnish (Art.No. 2050-001) or a 2-C PU varnish such as EPIFANES DD Varnish (2063-900) is recommended.Technical DataApplication area: 2-C clear varnish for wood above the waterline, interior and exteriorSubstrate: solid wood and plywood, suitable for teak, iroko, Oregon pinePrimer: Not requiredCoverage: approx. 14 m²/l at 30 µm dry film thicknessThinning: EPIFANES Thinner for PP Varnish Extra (Art.No. 2059-501)Mixing ratio: 1:1 by volumeApplication method: Brush or spray gun (professional users)Drying times (at 20 °C): Dust dry: 1 hr, sandable: 20 hrs, recoatable wet-on-wet: 5 hrs (brush), 2.5 hrs (spray gun)Further information on application can be found in the Technical Data Sheet under 'Downloads'.Safety note: Contains isocyanates. May cause allergic reactions. 

Extremely hard, high-gloss 2-component clear coat with UV filter. EPIFANES POLYURETHANE CLEAR COAT is suitable for interior and exterior use above the waterline in fresh and saltwater environments. The varnish offers very good UV protection, is resistant to water, alcoholic beverages, and mild chemicals, and forms a particularly hard, impact-resistant surface with excellent adhesion to solid wood, plywood, and veneers. Due to its excellent flow properties, it is also suitable for high-gloss finishes with a brush. Application: The two components are mixed in a ratio of 2:1 (base:hardener, by weight) and left to stand for 30 minutes (induction time). Application is done with a brush or spray gun at temperatures from 10 °C and a maximum of 75% relative humidity. A “mist coat” is recommended for the first spray pass. Thinning with EPIFANES PU Brush Thinner (Art.No. 2059-301) or PU SPRAY THINNER (Art.No. 2059-310) is possible. An intermediate sanding is not required if the next coat is applied within 24 hours.Technical DataApplication area: High-gloss 2-C clear coat for wood in above-water areas Substrate: Solid wood, plywood, veneer – clean, dry, sandedPrimer: none, optionally EPIFANES Vernis Extra for fast layer buildupCoverage: approx. 12 m²/kg at 30 µm dry film thicknessThinning: EPIFANES PU Brush Thinner, PU Spray Thinner Application method: Brush or spray gun Drying times (at 20 °C): Dust-dry: 2 hrs, tack-free: 4 hrs, sandable and recoatable: 24 hrsFurther processing information can be found in the Technical Data Sheet under 'Downloads'.Safety Note: Contains isocyanates. may cause allergic reactions. 

EPIFANES RAPIDCLEAR is a fast-drying, satin gloss clear varnish based on urethane/alkyd resin with integrated UV filter. The varnish forms a transparent, amber-colored protective film that preserves the natural appearance of the wood grain. RAPIDCLEAR is suitable for interior and exterior applications above the waterline – especially for oily woods such as teak – and can also be used as a quick base coat before high-gloss systems like EPIFANES Yacht Varnish (Art.No. 2050-001) or Hardwood Varnish Oil (Art.No. 2051-050).Application: The surface must be clean, dry, grease-free, and sanded (max. wood moisture: 15%). Application is done with a brush or spray gun at temperatures between 12 °C and 28 °C. No sanding is required between coats if recoated within 72 hours. For a high-gloss finish, EPIFANES YACHT VARNISH CLEAR can be applied to the sanded surface. Technical DataArea of application: UV-resistant clear varnish for wood above the waterline, interior and exteriorSubstrate: Clean, dry, sanded, max. 15% wood moisturePrimer: Not requiredCoverage: approx. 13 m²/l at 30 µm dry film thicknessThinner: Epifanes Paint Thinner (brush), Epifanes 1K Spray Thinner (spray gun)Application method: Brush or spray gun (not airless)Drying times (at 20 °C): Dust dry: 1 h, sandable: 2 h, recoatable: 5–8 hDurability: For long-lasting UV protection, at least 5–6 coats recommendedFurther information on application can be found in the Technical Data Sheet under 'Downloads'.

A transparent, high-gloss clear varnish based on modified oleophenolic (oil-compatible) resins with linseed oil and tung oil. It contains UV filters and is characterized by high elasticity, long-lasting gloss retention, and reliable protection against weather influences, sunlight, and temperature fluctuations. RYLARD VG 66 PREMIUM is particularly suitable for high-quality varnishing of wood on and on classic boats.Application: The surface must be clean, grease-free, and dry. On untreated or stripped wood, first apply two coats of diluted RYLARD VG 66 PREMIUM (1:1 with white spirit). Then apply four to six coats of undiluted varnish at intervals of at least 24 hours. A light intermediate sanding is recommended before the final coat.Technical DataApplication area: High-gloss protective varnish for wood in maritime outdoor areasSubstrate: Untreated or stripped, clean and dry woodPrimer: none, optional RYLARD VG 61Coverage: 18 m²/lThinner: white spiritApplication method: Brushing or spraying Drying times (at 20 °C): Dust dry after 8 h, reworkable after 24 hFurther information on application can be found in the Technical Data Sheet under 'Downloads'.

EPIFANES RUBBED EFFECT VARNISH is a fast-drying, scratch-resistant 1-component clear varnish based on urethane/alkyd resin with a satin finish. The varnish is suitable exclusively for interior areas and creates a warm, silky surface with good resistance to alcohol and common household cleaners. Application: On bare wood, it is recommended to first build up with several coats of high-gloss varnish such as EPIFANES CLEAR VARNISH (Art.No. 2050-001). Then, apply two coats of EPIFANES RUBBED EFFECT VARNISH. Best results are achieved with a soft long-hair brush. Alternatively, spray application is also possible. Wet sanding between coats with P400 is recommended. Technical DataApplication area: Satin finish topcoat for interior surfacesSubstrate: existing paint systems; clean, dry, sandedPrimer: High-gloss clear varnish (e.g. EPIFANES CLEAR VARNISH) recommended as base build-upCoverage: approx. 15 m²/l at 30 µm dry film thicknessThinner: EPIFANES PAINT THINNER (Art.No. 2059-001), EPIFANES SPRAY THINNER (Art.No. 2059-110)Application method: Brush, spray equipment (professional users)Drying times (at 20 °C): Dust dry: 1 hr, sandable: 12 hrs, recoatable: 12 hrsFurther information on application can be found in the Technical Data Sheet under 'Downloads'.

HEMPEL'S DURA-GLOSS VARNISH is a fast-drying, high-gloss clear varnish with a balanced ratio of hardness and flexibility. The formulation with optimized UV filters offers long-lasting protection and a professional appearance. The varnish is resistant to abrasion and wear and is suitable for new and maintenance coatings on wooden surfaces indoors and outdoors above the waterline.Application: For untreated wood, a primer with HEMPEL'S WOOD IMPREG (Item No. 2577-016) is recommended as a first coat. This is followed by two thinned coats of DURA-GLOSS VARNISH (first coat max. 20%, second max. 10% thinned with HEMPEL'S THINNER 811 (Item No. 2577-900)), then three unthinned coats. Sanding between coats is recommended. For maintaining existing coatings, sand an clean the surface and apply three unthinned coats.Technical DataApplication area: High-gloss clear varnish for wood indoors and outdoors above the waterlineSubstrate: Dry, clean, grease-free, max. 16% wood moisturePrimer: HEMPEL'S WOOD IMPREG for untreated woodCoverage: approx. 19 m²/l at 25 µm dry film thicknessThinner: HEMPEL'S THINNER 811Application method: Brush, varnish pad, spraying (professional users)Drying times (at 20 °C): Touch dry: 3 hrs, sandable: 24 hrs, recoatable: 4–48 hrs (depending on number of coats and temperature)Further information on application can be found in the Technical Data Sheet under 'Downloads'.

EPIFANES POLY-URETHANE DD-Yacht Varnish satin gloss is a scratch-resistant two-component clear varnish based on saturated polyester resins and isocyanate with integrated UV filter. The varnish is water-resistant, impact-resistant, and resistant to alcohol as well as mild chemicals. It is suitable for wooden surfaces indoors and outdoors above the waterline, especially for dimensionally stable woods such as marine plywood, solid wood, and wood veneer. It is particularly suitable as a satin gloss finish on EPIFANES POLY-URETHANE DD Yacht Varnish clear (Art.No. 2063-900), PP-VERNIS EXTRA Clear Varnish (Art.No. 2063-901), epoxy resins, and existing two-component satin varnishes.Application: Stir the components well and mix in a ratio of 2:1 (base:hardener) by weight and let stand for 15-30 minutes (induction time). If necessary, adjust to application viscosity with thinner. The varnish can be applied with a brush or spray gun. Application should be done at a minimum of 10 °C, with relative humidity not exceeding 75%. An intermediate sanding is not necessary if overcoated within 24 h. After 48 h, intermediate sanding with P360 is necessary. For optimal layer build-up, priming with EPIFANES PP VARNISH EXTRA is recommended.Technical DataApplication area: Satin-gloss 2-C clear varnish for indoor and outdoor areas above the waterlineSubstrate: Dimensionally stable wood (plywood, solid wood, veneer)Primer: EPIFANES PP VARNISH EXTRA recommended for base build-upCoverage: approx. 12 m²/kg at 30 µm dry film thicknessThinner: EPIFANES PU Brush Thinner, PU Spray ThinnerApplication method: Brush or spray gun (professional users)Drying times (at 20 °C, 65% rel. hum.): Dust dry: 2 hrs, tack-free: 4 hrs, sandable: 24 hrs, recoatable: 24 hrsFor more information on application, see the Technical Data Sheet under 'Downloads'.Safety notice: Contains isocyanates. may cause allergic reactions. 

EPIFANES AQUA MARINE SATIN VARNISH is a water-based, satin-finish interior clear varnish based on polyurethane/acrylic resin. It is characterized by high scratch resistance, fast drying, and high resistance to alcohol and common household cleaners. Suitable for all types of wood in interior areas and results in a clear, even surface after drying. The product is VOC-reduced and low-odor, ideal for interiors with high demands on application and environmental compatibility.Application: For bare wood, a multi-layer build-up with EPIFANES CLEAR BOAT VARNISH (Art. No. 2050-001) is recommended, which is then finished with two coats of EPIFANES AQUA MARINE SATIN VARNISH. Alternatively, the varnish can be applied directly to clean and sanded old coatings. Application is done with a brush or spray gun at temperatures above 8 °C and max. 85% relative humidity. An intermediate sanding with P220 is required between coats. Thinning with water up to a maximum of 15% is possible. Note: The varnish appears milky during application but dries clear.Technical DataApplication area: Satin-finish clear varnish for all wooden surfaces indoorsSubstrate: Clean, dry, grease-free; suitable for all types of woodPrimer: Multi-layer base with EPIFANES CLEAR BOAT VARNISH (Art. No. 2050-001) recommendedCoverage: approx. 12 m²/l at 25 µm dry film thicknessThinning: Water, 0–15%Application method: Brush or spray gun (1.5–1.8 mm, 2–3 bar)Drying times (at 20 °C, 65% r.h.): Dust-dry: 1 hr, sandable: 4 hrs, recoatable: 6 hrsFor more information on application, please refer to the Technical Data Sheet under 'Downloads'.

BIOPIN BOOTSLACK is a traditional, high-gloss wood oil clear varnish with good elasticity and excellent flow. It is weatherproof, seawater-resistant, and abrasion-resistant. The product has good penetration and adhesion properties and offers long-term protection against UV radiation. Application Apply on a dry, dust- and grease-free surface using a brush, roller, or spray device at temperatures above 8 °C. For new wood, a primer with BIOPIN BOOTSLACK (diluted 10–20%) or BIOPIN BOAT OIL (Art.No. 2631-140) is recommended. Then apply one to three undiluted coats, sanding between coats. For old coatings in poor condition, complete removal may be necessary. For old coatings in good condition, sanding and 1–2 new coats are sufficient. Do not crumple contaminated cloths due to risk of spontaneous ignition; instead, allow them to dry spread out.Technical DataApplication area: Clear varnish for wood indoors and outdoors, especially for boats and damp areasSubstrate: Clean, dry, dust- and grease-free; also suitable for wood-based materialsPrimer: BIOPIN BOOTSLACK diluted or BIOPIN BOAT OILCoverage: approx. 12 m²/l Thinner: BIOPIN THINNER or turpentine oilApplication method: Brush, roller, spray device (professional use)Drying times (at 20 °C): Dust-dry: 4–6 hrs, recoatable: after 8–12 hrs (depending on temperature fluctuations)Further information on application can be found in the technical data sheet under 'Downloads'.

High-gloss, fast-drying polyurethane clear coat with an especially hard surface and very good weather and UV resistance. The amber-colored varnish enhances the natural wood grain and is suitable for all common types of wood in outdoor areas above the waterline. INTERNATIONAL COMPASS clear varnish is resistant to oil, mild acids, alkalis, and alcohol splashes and can also be applied directly to oily woods such as teak or iroko.Application: The surface must be clean, dry, and free of grease. For raw wood, the first coat should be applied thinned, followed by 3–5 unthinned coats with sanding between every 2nd to 3rd coat (P320–400). For oily woods, pretreatment with INTERNATIONAL Thinner No. 1 (Art.No. 2550-006) is recommended. Application is done with a brush, roller, or spray device at temperatures between 5 °C and 35 °C. Technical DataArea of application: High-gloss clear coat for outdoor areas above the waterlineSurface: Clean, dry, sanded, max. 18% wood moisture; also suitable for teak and irokoPrimer: none, thin the first coatCoverage: approx. 14.3 m²/l (theoretical)Thinner: Brush: Thinner No. 1 , Spraying: Thinner 910 or 920Application method: Brush, foam roller, or professional spray deviceDrying times (at 15 °C): Dust dry: 45 min, recoat: after 8 hrs.For further information on application, please refer to the Technical Data Sheet under 'Downloads'.

Traditional, high-gloss clear varnish based on wood oil with excellent UV protection. INTERNATIONAL SCHOONER is suitable for interior and exterior areas above the waterline and can also be applied directly to oily woods such as teak and iroko. SCHOONER offers excellent water resistance, good flow properties, and a warm, golden tone.Application: On bare wood, the first coat is applied thinned with 10% INTERNATIONAL Thinner No. 1 (2550-006). This is followed by 4–6 unthinned coats with intermediate sanding (grit P320–P400). Previously varnished surfaces are cleaned with Super Cleaner, sanded, and refinished with 2–4 coats. Application is done with a brush, roller, or spray equipment at 10–29 °C. Good ventilation and a dry environment are required for drying.Technical DataApplication area: High-gloss clear varnish for wood in above-water areas, interior and exteriorSubstrate: Wood, especially oily woods such as teak and iroko Primer: Not required; priming through 10% thinned first coatCoverage: approx. 14 m²/l (brush), approx. 12 m²/l (spraying)Thinner: Thinner No. 1 (brush), No. 1 or No. 910 (spraying)Application method: Brush, roller, conventional or airless spray application (professional use only)Drying times (at 15 °C): Dust dry: 2.5 hrs, recoatable: 14 hrs–1 monthFor more information on application, refer to the Technical Data Sheet under 'Downloads'.

LE TONKINOIS PARQUETS is an open-pore parquet varnish based on oil for wooden floors in indoor areas. The formulation with linseed oil, tung oil, and alkyd resins allows deep penetration into the wood capillaries, thereby reducing swelling and shrinking. The varnish offers long-lasting protection against abrasion and wear and is also UV-resistant. The natural wood grain is preserved and visually enhanced.Application: Wooden surfaces to be treated should be sanded, free of grease and dust. For soft woods, a prior primer coat with LE TONKINOIS Bio Impression is recommended. Stir well before use, do not dilute. LE TONKINOIS PARQUETS is applied in thin layers with a brush, roller, or floor varnish roller. Depending on the type of wood, apply at least two to three coats. Apply only one coat per day. Sand between layers with max 180 grit.Technical DataApplication area: Protective varnish for indoor wooden floorsSubstrate: Untreated wood, wood-based materialsPrimer: Bio Impression for soft woods (optional)Coverage: 20 m²/l per coat (depending on the absorbency of the wood)Application method: Brushing, rolling, sprayingDrying times (at 20 °C): Dust-dry after 6–8 h, re-coatable after 24 hFor more information on application, see the Technical Data Sheet under 'Downloads'.

Quick-drying, teak-tinted, semi-matt clear varnish with integrated UV filter for all types of wood above the waterline. The varnish combines easy application with good flow and even coloration - even on oily woods such as teak. EPIFANES RAPIDCOAT can be used both indoors and outdoors and is suitable as the sole protective coating or as a base for EPIFANES RAPIDCLEAR (Art.No. 2051-075), boat varnish (Art.No. 2050-001) or WOODFINISH GLOSS/MATTE (Art.No. 2051-001/2051-002).Application: The surface must be dry, clean and degreased. Apply with a soft brush or by spraying at 8-30 °C. Stir the container well and apply 5-6 coats. For a high-gloss finish, finish with RAPIDCLEAR or a high-gloss lacquer. Intermediate sanding is not necessary within 72 h. If the interval is exceeded, sand the surface lightly (P280-320).Technical dataArea of application: Pigmented wood protection for interior and exterior areas above the waterlineSubstrate: All common types of wood, incl. teak

HEMPEL'S CLASSIC VARNISH is a traditional, transparent clear varnish based on alkyd resin and tung oil (chinese wood oil). It forms a flexible and weather-resistant high-gloss film with good resistance to seawater, UV radiation, and fluctuating weather conditions. The varnish is suitable for new and renovation coatings on wood surfaces indoors and outdoors above the waterline.Application On new untreated wood, a priming coat with HEMPEL'S WOOD IMPREG (Art.No 2577-016) is recommended. This is followed by two thinned coats with HEMPEL'S THINNER 811 (Art.No 2577-900) (first coat max. 20%, second max. 10%), then three unthinned coats. Sanding between coats is recommended. For maintaining existing varnished surfaces, a light sanding is recommendede followed by three unthinned coats. Technical DataField of application: Clear varnish for wood surfaces above the waterline (indoor and outdoor)Substrate: Dry, clean, grease-free, sanded; max. 16% wood moisturePrimer: HEMPEL'S WOOD IMPREG (Art.No 2577-016) recommended for new woodCoverage: approx. 17 m²/l at 30 µm dry film thicknessThinner: HEMPEL'S THINNER 811 (Art.No 2577-900), max. 20%Application method: Brush, varnish pad, spraying (professional use)Drying times (at 20 °C): Touch dry: 6 hrs, sandable: 24 hrs, recoatable: 8–48 hrsFurther information on application can be found in the Technical Data Sheet under 'Downloads'.

A traditional clear varnish that is highly elastic, has great penetrating properties, and does not peel. Traditionally manufactured by gently cooking linseed and tung oil. RYLARD VG63 dries very slowly compared to synthetic resin varnishes, which accounts for the elasticity and durability required for solid wood boats. The varnish is particularly suitable for use on wood in marine environments or other highly demanding conditions.Application: Apply two coats of RYLARD IMPREGNANTE (Art. No. 6080-701) or thinned VG 63 to dry, clean wood. Then apply at least four to six coats undiluted – each coat thin and with a 24-hour interval. The first coat should be diluted by 30–40%, with dilution gradually reduced thereafter. No dilution is intended for the final two coats. Intermediate sanding with fine sandpaper is recommended. Do not apply in damp weather, below 15 °C, or on wet wood.RYLARD VarnishesThe Italian marine and yacht paint manufacturer BRAVA from Genoa offers with its RYLARD brand a range of traditional yacht varnishes, whose original formulation was developed for the emerging yachting sport in the 19th century and is referred to on many classic yachts as the "Yachtman‘s Mirror".Technical DataApplication area: Clear varnish for wooden surfaces in maritime and demanding environmentsSubstrate: Clean, dry, untreated or stripped woodPrimer: RYLARD IMPREGNANTE (optional)Coverage: 20 m²/lThinner: Turpentine substituteApplication method: Brushing or sprayingDrying times (at 20 °C): Dust-dry after 12 h, re-coatable after 24 hFor more information on application, see the technical data sheet under 'Downloads'.

INTERNATIONAL ORIGINAL is a traditional, high-gloss clear varnish based on wood oil with excellent UV protection. The product is suitable for all common types of wood above the waterline and impresses with good flexibility, long-lasting gloss retention, and a clear, warm appearance – especially on light woods. The varnish is water-resistant, non-chalking, and suitable for both interior and exterior use.Application: The surface must be dry, free of grease, and sanded (bare wood: P80–180, old coatings: P280–320). Stir well before use. The first coat should be thinned with 10–15% INTERNATIONAL Thinner No. 1 (Art.No. 2550-006). Then apply at least three undiluted coats. An intermediate sanding with P320–400 is recommended between coats. Application is done with a brush, roller, or spray device at temperatures from 10–35 °C.Technical DataArea of application: High-gloss clear varnish for wood above the waterline (interior and exterior)Substrate: All types of wood with appropriate preparation, max. 18% wood moisturePrimer: noneCoverage: approx. 12.5 m²/l (theoretical)Thinner: Brush: Thinner No. 1, Spraying: Thinner 910 or 920Application method: Brush, roller, conventional spraying, airless or airmix (professionals only)Drying times (at 15 °C): Dust dry: 10 hrs, recoatable: 24 hrs to 4 daysFor more information on application, please refer to the Technical Data Sheet under 'Downloads'.

VOSSCHEMIE G8 SUPER is a one-component polyurethane clear coat with high resistance to chemicals, cleaners, and weathering. The solvent-based coating cures through humidity, remains nearly non-yellowing, and is suitable for many absorbent substrates such as wood, metal, and solvent-resistant plastics. Due to its formulation, the product does not contain additional UV absorbers and is not suitable for use in living areas.Application: G8 SUPER is applied with a brush or spray gun. The substrate must be clean, dry, and free of grease; solid wood must not exceed a maximum wood moisture content of 15%. For priming on porous substrates, dilution with a maximum of 50% polyurethane thinner is recommended. The application amount per layer should not exceed 250 ml/m². For a durable surface film, at least three undiluted coats are required. Recoating can be done after 2–4 h or alternatively after intermediate sanding.Technical DataApplication area: Clear coat for wood, metal, plastics, and epoxy laminatesSubstrate: Clean, dry, grease-free; solid wood max. 15% wood moistureCoverage: approx. 200–300 ml/m² per coatThinning: Max. 50% polyurethane thinner recommended for primingApplication method: Brushing or sprayingDrying times (at 20 °C): Dust dry after 2–4 h, recoatable within 24 hCuring time: Fully cured after at least 7 daysNote: Product contains hazardous chemicals according to the REACH regulation. We recommend use only by professional users. Contains isocyanates. May cause allergic reactions. As of August 24, 2023, appropriate training must be completed before industrial or professional use (EU REACH regulation). Further information can be found in the technical or safety data sheet under 'Downloads'. 

LACQ YACHTLACK is a traditionally cooked clear varnish based on wood oil and phenolic resin with a high solids content and integrated UV filter. It forms a high-gloss, elastic protective layer with excellent weather and water resistance. The varnish is suitable for new builds on solid, raw wood (e.g. mahogany, meranti, Oregon pine) as well as for renovation coats on intact 1K or 2K varnish systems in the above-water area. Also suitable for doors, window frames, and garden furniture.Application: The varnish is applied with a brush or by spraying. For new builds, seven coats are recommended: the first coat diluted 50%, the second 25%, the third 15%, coats 4 to 7 only 0–5%. Intermediate sanding is done with P220 (dry), P280 (dry), and P400 (wet). Dilution is done with turpentine (brush) or petrol (spray gun). Technical DataApplication area: High-gloss clear varnish for wood surfaces in the above-water area Substrate: Solid wood (e.g. mahogany, meranti, Oregon pine), plywood; clean, dry, sandedPrimer: Not required Coverage: approx. 14 m²/l (depending on substrate and application)Thinning: Turpentine (brush), petrol (spraying)Application method: Brush or spray gun (1.2–1.5 mm nozzle, 2–3 bar, 20–24 sec. DIN 4)Drying times (at 18 °C): Dust dry: approx. 24 hrs, recoatable: approx. 24 hrsFurther information on application can be found in the Technical Data Sheet under 'Downloads'.

Extremely hard, high-gloss 2-component clear varnish with UV filter. EPIFANES POLY-URETHANE Yacht Varnish Karaat Mahogany has the same properties as EPIFANES POLY-URETHANE Clear Varnish (Art.No. 2063-900). Due to its mahogany-colored pigmentation, it is suitable for tinting existing varnish systems or for a reddish-pigmented new build on bare wood. Suitable for interior and exterior use above the waterline in fresh and saltwater environments. The varnish offers very good UV protection, is resistant to water, alcoholic beverages, and mild chemicals, and forms an especially hard, impact-resistant surface with excellent adhesion to solid wood, plywood, and veneers. Due to its excellent flow properties, it is also suitable for high-gloss finishes with a brush.Application: The two components are mixed in a ratio of 2:1 (base:hardener, by weight) and left to stand for 30 minutes (induction time). Application is done with a brush or spray gun at temperatures from 10 °C and a maximum of 75% relative humidity. A "mist coat" is recommended for the first spray application. Dilution with EPIFANES PU Brush Thinner (Art.No. 2059-301) or PU SPRAY THINNER (Art.No. 2059-310) is possible. An intermediate sanding is not required if the next coat is applied within 24 hours.Technical DataApplication area: High-gloss 2-component clear varnish for wood above the waterlineSubstrate: Solid wood, plywood, veneer – clean, dry, sandedPrimer: none, optionally EPIFANES Vernis Extra for quick build-upCoverage: approx. 12 m²/kg at 30 µm dry film thicknessThinning: EPIFANES PU Brush Thinner, PU Spray ThinnerApplication method: Brush or spray gunDrying times (at 20 °C): Dust-dry: 2 hrs, tack-free: 4 hrs, sandable and recoatable: 24 hrsFurther information on application can be found in the Technical Data Sheet under 'Downloads'.Safety note: Contains isocyanates. May cause allergic reactions.

EPIFANES POLY-URETHANE DD-YACHT VARNISH COLORED is a high-gloss, extremely hard 2-component colored varnish based on saturated polyester resins and isocyanate with integrated UV filter. The product is particularly scratch-, impact-, and abrasion-resistant and offers very good weather and water resistance even in tropical climates. Suitable for wood, steel, aluminum, and GRP in interior and exterior areas above the waterline. Can be applied directly to thoroughly degreased and sanded polyester surfaces and is compatible with common epoxy and polyurethane primers.Application: The two components are mixed in a ratio of 2:1 (base:hardener, by weight) and ideally left to stand for 30 minutes (induction time). Application is carried out with a brush, roller, or spray gun at temperatures of 10–30 °C and relative humidity between 50% and 75%. Do not apply wet-on-wet. Between coats, intermediate sanding with P360–P400 is required unless the next coat is applied within 24 hrs. Dilution possible with EPIFANES PU BRUSH THINNER (Art. No. 2059-301) or PU SPRAY THINNER (Art. No. 2059-310).Note on the color chart: The colors shown correspond as closely as possible to the original colors, but deviations cannot be ruled out.Technical DataApplication area: Wood, steel, aluminum, and GRP above the waterlineSubstrate: Clean, dry, grease-free, sanded; GRP at least 14 days oldPrimer: EPIFANES EPOXY PRIMER or EPOXY HB COAT depending on materialCoverage: approx. 12–14 m²/l at 35–40 µm dry film thicknessThinning: EPIFANES PU BRUSH THINNER, PU SPRAY THINNER Application method: Brush, roller, or spray gun (professional users)Drying times (at 20 °C): Dust dry: 2 hrs, tack-free: 4 hrs, sandable and recoatable: 24 hrsFurther information on application can be found in the Technical Data Sheet under 'Downloads'.Safety Note: Contains isocyanates. may cause allergic reactions. 

High-gloss, single-component varnish based on urethane oil with very good color stability. EPIFANES MONO-URETHANE Yacht Varnish combines the easy application of traditional 1-component systems with the approximate hardness and weather resistance of a 2-component varnish. The product is suitable for new and renovation coatings on primed wood, steel, aluminum, and fiberglass above the waterline for interior and exterior use. On carefully degreased and sanded fiberglass, direct application without primer is possible.Application: For optimal adhesion, appropriate priming with EPIFANES MULTI MARINE PRIMER (Art.No 2066-102) is required, and for aluminum surfaces additionally with WASHPPRIMER AQ (Art.No 2062-005). Application is done with brush, roller, or spray gun at temperatures between 8 °C and 30 °C and relative humidity between 50% and 85%. Do not apply wet-on-wet. An intermediate sanding with P400 or Scotch-Brite is recommended between coats.Note on the color chart: The colors shown correspond as closely as possible to the original colors, but deviations cannot be ruled out.Technical DataApplication area: High-gloss varnish for wood, steel, aluminum, and fiberglass above the waterlineSubstrate: Clean, dry, grease-free, sandedPrimer: EPIFANES MULTI MARINE PRIMER, WASHPPRIMER AQ (aluminum)Coverage: approx. 14–15 m²/l at 40 µm dry film thicknessThinner: EPIFANES BRUSH THINNER, 1-C SPRAY THINNER Application method: Brush, roller, or spray gun (professional users)Drying times (at 20 °C): Dust-dry: 1 hr, sandable: 24 hrs, recoatable: 24 hrsFurther information on application can be found in the technical datasheet under 'Downloads'.

Classic, high-gloss yacht varnish based on alkyd resin for applications above the waterline. EPIFANES YACHT ENAMEL is suitable for primed surfaces made of wood, steel, aluminum, and fiberglass for interior and exterior use and is resistant to salt and fresh water. It is known for its optimal flow properties, long-lasting gloss, and good weather resistance. Compatible with many existing 1-component and 2-component systems and can also be overcoated with EPIFANES MONO-URETHANE (Art.No. 2055-101) or EPIFANES NAUTIFORTE (Art.No. 2054-102).Application The surface must be clean, dry, dust- and grease-free. Sand old coatings, remove loose or non-adhering layers. Application is done with brush, roller, or spray gun at temperatures above 8 °C and relative humidity below 85%. Do not apply wet-on-wet. For even gloss, intermediate sanding is required. The recommended wet film thickness is 70–80 µm, corresponding to 35–40 µm dry. As a primer, use EPIFANES MULTI MARINE PRIMER (Art.No 2062-102), additionally WASHPRIMER AQ (Art.No 2062-005) for aluminum surfaces.Note on the color chart: The colors shown correspond as closely as possible to the original colors, but deviations cannot be ruled out.Technical DataApplication area: High-gloss varnish for wood, steel, aluminum, and fiberglass above the waterlineSubstrate: Clean, dry, grease-free, sanded; fiberglass at least 14 days oldPrimer: EPIFANES MULTI MARINE PRIMER, WASHPRIMER AQ Coverage: approx. 14 m²/l at 40 µm dry film thicknessThinner: EPIFANES COLOR THINNER, 1-C SPRAY THINNERApplication method: Brush, roller, spray gun (professional application)Drying times (at 20 °C): Dust-dry: 2 hrs, sandable: 24 hrs, recoatable: 24 hrsFurther information on application can be found in the technical datasheet under 'Downloads'.

EPIFANES BILGENFARBE is a one-component, air-drying protective coating based on oil-modified alkyd resins with a semi-gloss finish. It is intended for use in bilges, engine rooms and other areas where a hard and resistant coating is required. Suitable for applications on steel, GRP, wood and aluminum in conjunction with the appropriate primer system.Application: The substrate must be clean, grease-free, well sanded and dust-free. Apply with a brush, roller or sprayer at temperatures from 5 °C and a maximum relative humidity of 85 %. Stir well before use.Recommended wet film thickness: 70-80 µm (35-40 µm dry) or 100-200 µm (50-100 µm dry).Technical dataArea of application: Protective coating for bilges, engine rooms and other heavily used areasSubstrate: Steel, GRP, wood, aluminum

Classic, high-gloss yacht varnish based on alkyd resin for applications above the waterline. EPIFANES BOOTSLACK colored is suitable for primed surfaces made of wood, steel, aluminium and GRP indoors and outdoors and is resistant to salt and fresh water. It is characterized by optimum flow properties, long-lasting gloss and good weather resistance. Compatible with many existing 1-component and 2-component systems and can also be recoated with EPIFANES MONO-URETHANE (Art. No. 2055-101) or EPIFANES NAUTIFORTE (Art. No. 2054-102).Application The substrate must be clean, dry and free of dust and grease. Sand old coats, remove loose or non-adherent layers. Apply with a brush, roller or sprayer at temperatures above 8 °C and relative humidity below 85 %. Do not apply wet-on-wet. Intermediate sanding is required for a uniform gloss. The recommended wet film thickness is 70-80 µm, corresponding to 35-40 µm dry. Use EPIFANES MULTI MARINE PRIMER (Art. No. 2062-102) as a primer, for aluminum surfaces additionally&nbsp

Classic, high-gloss yacht varnish based on alkyd resin for applications above the waterline. EPIFANES BOAT VARNISH pure white is suitable for primed surfaces made of wood, steel, aluminum, and GRP for interior and exterior use and is resistant to salt and fresh water. It is characterized by optimal flow properties, long-lasting gloss, and good weather resistance. Compatible with many existing 1-component and 2-component systems and can also be overcoated with EPIFANES MONO-URETHANE (Art.No. 2055-101) or EPIFANES NAUTIFORTE (Art.No. 2054-102).Application: The surface must be clean, dry, dust- and grease-free. Sand old coatings, remove loose or non-adhering layers. Application is carried out with brush, roller, or spray gun at temperatures above 8 °C and relative humidity below 85 %. Do not apply wet-on-wet. For an even gloss, intermediate sanding is required. The recommended wet film thickness is 70–80 µm, corresponding to 35–40 µm dry. As a primer, use EPIFANES MULTI MARINE PRIMER (Art.No. 2062-102); for aluminum surfaces additionally use WASHPRIMER AQ (Art.No. 2062-005).Technical dataApplication area: High-gloss varnish for wood, steel, aluminum, and GRP above the waterlineSubstrate: Clean, dry, grease-free, sanded; GRP at least 14 days oldPrimer: EPIFANES MULTI MARINE PRIMER, WASHPRIMER AQCoverage: approx. 14 m²/l at 40 µm dry film thicknessThinner: EPIFANES PAINT THINNER, 1-C SPRAY THINNERApplication method: Brush, roller, spray gun (professional use)Drying times (at 20 °C): Dust dry: 2 hrs, sandable: 24 hrs, re-coatable: 24 hrsFor further information on application, please refer to the Technical Data Sheet under 'Downloads'.

“Pure Gold in a tin” - EPIFANES GOLD SPECIAL contains a very high proportion of metallic, pure gold dust pigments. This gold paint was developed on an acrylic copolymer basis for decorative stripes, ship names, and lettering on classic yachts, where traditionally gold leaf was laboriously applied. In contrast, EPIFANES GOLD SPECIAL is easier to apply than gold leaf and allows the included gold dust to shine in its typical gloss and color tone. Application: The surface must be dry, well degreased, and sanded. On GRP, steel, wood, and zinc, an adhesion-promoting primer with EPIFANES MULTI MARINE PRIMER (Art.No 2066-175) is recommended, which should be sanded with P180–P220 after drying. Stir well before use and stir occasionally during application to prevent the gold pigments from settling. Do not apply wet-on-wet and do not apply excessively thick wet coats. Preferably apply with a soft, long-bristled brush in a single, even stroke. For an even gold effect, apply at least two coats.Outdoors, to stabilize against UV rays, after complete curing (48 hrs) it can be overcoated with EPIFANES POLY-URETHANE CLEAR VARNISH (Art.No 2063-900) or EPIFANES CLEAR BOAT VARNISH (Art.No 2050-001); when using Clear Boat Varnish, the color tone appears slightly darker.Safety note: Contains solvents; wearing personal protective equipment (safety goggles, mask, gloves) is recommended.Technical DataArea of application: Gold paint for decorative coating of lettering, trim, ornamentsSurface: Dry, degreased, sanded; on GRP, steel, wood with primerPrimer: depending on surface, e.g., EPIFANES MULTI MARINE PRIMER, WASHPRIMER AQCoverage: approx. 2.0–2.5 m²/250 ml at approx. 45–55 µm dry film thicknessThinner: EPIFANES PAINT THINNER (Art.No. 2059-001)Application method: BrushDrying times (at 20 °C): Dust dry: 2 hrs, sandable: 24 hrs, recoat with itself: 9–12 hrs; recoat with clear varnish: approx. 48 hrs.

SIGMARINE 49 is a high-gloss alkyd topcoat for interior and exterior areas above the waterline. It is easy to apply with a brush and shows very good flow, high weather resistance, opacity and color stability. The paint is also resistant to sulphur dioxide (occurs in areas with high levels of air pollution). Not suitable for permanent exposure to water or continuous exposure to spray water.

EPIFANES BLACK BOTTOM flexible bitumen-based protective coating for the area above and below the waterline.This modern version of the so-called black varnish adheres well to raw steel and wood surfaces as well as existing tar and bitumen layers and synthetic primers. It is easy to apply, offers high UV resistance, elasticity and protection against the changing influences of water and air.Note: It is recommended to apply the first layer with 15-25% with EPIFANES 1K-Spraythinner and use a stiff brush to work the paint onto the surface. For effective corrosion protection on new hulls, apply at least 250-300 μm to the raw substrate in the underwater area. Technical DataSubstrate: Steel, wood, existing tar coatings (repair/maintenance)Surface preparation:Clean, dry, degreased, well-sanded surface, free of rust, dust and adhesionDegrease with EPIFANES 1K Spray Thinner; rinse off water-soluble residues with fresh waterFollow-up coat: Overcoatable with EPIFANES Copper-Free AntifoulingCoverage: approx. 10 m²/l at 50 µm dry film thicknessThinner:Brush: EPIFANES Brush ThinnerSpray: EPIFANES Spray Thinner for 1C lacquers and primersAirless: EPIFANES D-100Application method: Brush, roller, conventional spray gun, airless sprayDrying times at 20 °C: Dust dry after 2 hrs, recoatable after 12 hrsFurther information on applying this product can be found in the technical data sheet under “Downloads”.

EPIFANES WATERLINE PAINT is a high-gloss, 1-component enamel based on urethane/alkyd resin, specially formulated for the waterline area. It is suitable for fresh and saltwater areas and offers increased protection against weathering to maintain gloss and color stability in the transition area between water and air. Applicable to GRP/gelcoat, steel, wood, and aluminum above the waterline. Application It is recommended to apply with a long-haired, soft brush, a mohair roller, or spray gun at temperatures between 10 °C and 28 °C and relative humidity between 50% and 75%. Before application, stir the can well. Do not work wet-on-wet. For a new build, at least two coats of EPIFANES WATERLINE PAINT are recommended. Between coats, sand lightly with P400. Thinning with EPIFANES PAINT THINNER (Art.No 2059-001) or 1-C SPRAY THINNER (Art.No 2059-110) is possible.TIP: It is recommended to paint the waterline 5–10 cm above the water (at full load) so that the paint does not have constant water exposure later.  Note on the color chart: The colors shown correspond as closely as possible to the original colors, but deviations cannot be ruled out.Technical DataApplication area: Waterline, on already coated surfacesSubstrate: Intact, clean, degreased, and sandedPrimer: EPIFANES MULTI MARINE PRIMER (Art.No 2055-301)Coverage: approx. 3–4 m²/250 ml at 40 µm dry film thicknessThinning: EPIFANES PAINT THINNER, 1-C SPRAY THINNER Application method: Brush, roller, spray (professional users)Drying times (at 20 °C): Dust-dry: 3 hrs, sandable: 24 hrs, overcoatable: 24 hrsFurther processing information can be found in the Technical Data Sheet under 'Downloads'.

Extremely fast-drying, robust yacht enamel that dries only semi-gloss, resulting in a certain degree of slip resistance. Suitable for applications above the waterline, especially for heavily used areas such as walking decks and hatch coamings.The paint offers very good adhesion, is mechanically durable, and is suitable for areas subject to heavy use. By adding up to 25% EPIFANES Clear Varnish (Art.No. 2050-001), the gloss level can be increased; by adding EPIFANES Anti-Slip Additive (Art.No. 2059-002), the slip resistance of the paint on walking decks can be increased.Can be applied to wood, steel, and aluminum above the waterline, as well as for refurbishing already existing, intact paint systems.Application The surface must be clean, dry, dust- and grease-free. Before application on smooth surfaces, sanding is required. Application is done with brush, roller, or spray gun at temperatures between 5 °C and 25 °C and relative humidity below 85%. Between coats, intermediate sanding with P220–P280 is required. For steel and wood outdoors, a suitable EPIFANES primer such as MULTI MARINE PRIMER (Art.No. 2066-175) or WERDOL Primer (Art.No. 2052-175) is recommended.Technical DataApplication area: Semi-gloss enamel paint for decks, walking decks, and heavily used areasSurface: Steel, wood, concrete; primed, dry, sanded, cleanPrimer: Suitable EPIFANES primer depending on the surfaceCoverage: approx. 8–10 m²/l at 60 µm dry film thicknessThinner: EPIFANES PAINT THINNER (Art.No 2059-001) or 1-K SPRAY THINNER (Art.No 2059-110)Application method: Brush, roller, spray gun (professional users)Drying times (at 15°C): Dust dry: 2 hrs, re-coatable: 10 hrsFurther information on application can be found in the Technical Data Sheet under 'Downloads'.

High-gloss, one-component urethane oil-based varnish with very good color fastness. EPIFANES MONO-URETHANE Yacht Varnish combines the ease of application of classic 1-component systems with the approximate hardness and weather resistance of a 2-component varnish. The product is suitable for new and renovation coatings on primed wood, steel, aluminum and GRP in interior and exterior areas above the waterline. Direct application without primer is possible on carefully degreased and sanded GRP.Application: For optimum adhesion, priming with EPIFANES MULTI MARINE PRIMER (Art. No. 2066-102) is required, for aluminum surfaces additionally with WASHPPRIMER AQ (Art. No. 2062-005). Apply with a brush, roller or sprayer at temperatures between 8 °C and 30 °C and relative humidity between 50 % and 85 %. Do not apply wet-on-wet. Intermediate sanding with P400 or Scotch-Brite is recommended between coats.Ordering the desired color: The EPIFANES MONO-URETHANE yacht varnish can be mixed in all RAL colors except metallics and luminous colors, and in all colors of the common maritime color manufacturers of EPIFANES. The varnish is also available in silk gloss. The delivery time is approx. 10 days. Please specify the exact color at the end of the order process under "Remarks".Technical dataArea of application: High-gloss paint for wood, steel, aluminum and GRP above the waterlineSurface: Clean, dry, grease-free, sandedPrimer: EPIFANES MULTI MARINE PRIMER, WASHPPRIMER AQ (aluminum)Coverage: approx. 14-15 m²/l at 40 µm dry film thicknessThinner: EPIFANES PINSELVERDÜNNER, 1-K SPRITZVERDÜNNUNG&nbsp

EPIFANES FLAT BLACK is a one-component, black matte finish based on urethane resin for interior and exterior areas. With a gloss rate of only 5–10%, it gives surfaces a modern, matte appearance. The product is resistant to alcohol and common household cleaners and has high scratch resistance.Application: The substrate must be clean, dry, grease-free, and sanded; application is done with a brush, roller, or spray gun. On GRP, steel, wood, or aluminum, a suitable primer such as EPIFANES MULTI MARINE PRIMER (Art.No. 2066-175) is recommended, depending on the material. Indoors, up to three coats are applied directly to the previously primed surface. Outdoors, a build-up with a high-gloss varnish such as EPIFANES MONO-URETHANE (Art.No. 2055-101) is recommended, followed by a final coating with 1–2 coats of EPIFANES FLAT BLACK.Technical DataApplication area: Matte finish for wood, steel, aluminum, GRP in interior and exterior areas above the waterlineSubstrate: Clean, dry, grease-free, sandedPrimer: Compatible with most EPIFANES paints and primersCoverage: approx. 15 m²/l at 35 µm dry film thicknessThinner: EPIFANES BRUSH THINNER FOR PAINTS & LACQUERS (Art.No. 2059-001); EPIFANES 1-C SPRAY THINNER (Art.No. 2059-110)Application method: Brush, roller, spray equipment (professional users)Drying times (at 15 °C): Dust dry: 3 hrs, sandable and re-coatable: 48 hrsFurther information on application can be found in the Technical Data Sheet under 'Downloads'.

Classic, high-gloss yacht enamel based on alkyd resin for applications above the waterline. EPIFANES YACHT ENAMEL Black is suitable for primed surfaces made of wood, steel, aluminum, and GRP for both interior and exterior use, and is resistant to salt and fresh water. It is characterized by optimal flow properties, long-lasting gloss, and good weather resistance. Compatible with many existing 1-component and 2-component systems.Application The substrate must be clean, dry, free of dust and grease. Sand old coatings, remove loose or non-adherent layers. Application is done with a brush, roller, or spray gun at temperatures above 8 °C and relative humidity below 85 %. Do not apply wet-on-wet. For uniform gloss, intermediate sanding is required. The recommended wet film thickness is 70–80 µm, corresponding to 35–40 µm dry. As a primer, use EPIFANES MULTI MARINE PRIMER (Art.No. 2062-102), for aluminum surfaces additionally use WASHPRIMER AQ (Art.No. 2062-005).Technical dataApplication area: High-gloss varnish for wood, steel, aluminum, and GRP above the waterlineSubstrate: Clean, dry, grease-free, sanded; GRP at least 14 days oldPrimer: EPIFANES MULTI MARINE PRIMER, WASHPRIMER AQCoverage: approx. 14 m²/l at 40 µm dry film thicknessThinner: EPIFANES PAINT THINNER, 1-C SPRAY THINNERApplication method: Brush, roller, spray gun (professional use)Drying times (at 20 °C): Dust dry: 2 hrs, sandable: 24 hrs, recoatable: 24 hrsFurther information on application can be found in the technical data sheet under 'Downloads'.

EPIFANES SATIN FINISH WHITE is a single-component satin gloss varnish based on urethane/alkyd resin for interior and exterior areas above the waterline. It is characterized by optimal flow, high coverage, and resistance to weathering as well as common household cleaning agents. The product is suitable for use on wood, steel, GRP, and aluminum in combination with the appropriate primer system. Suitable as a satin-matt finish over a high-gloss paint system.Application Application is carried out with a brush, roller, or spray gun at temperatures of 8–30 °C and relative humidity between 50% and 85%. In interior areas, 2–3 coats are applied to the previously primed surface. Intermediate sanding with P320–P400 is required between coats. Thinning with EPIFANES PAINT THINNER (Art.No. 2059-001) or 1-C SPRAY THINNER (Art.No. 2059-110) is possible.Technical dataApplication area: Satin-matt varnish for wood, steel, GRP, and aluminum above the waterlineSubstrate: Clean, dry, grease-free, sandedPrimer: EPIFANES MULTI MARINE PRIMER, MONO-URETHANE or WASHPRIMER AQ depending on substrateCoverage: approx. 13–15 m²/l at 40 µm dry film thicknessThinner: EPIFANES BRUSH THINNER, 1-C SPRAY THINNERApplication method: Brush, roller, spray gun (professional users)Drying times (at 20 °C): Dust dry: 2 hrs, sandable: 24 hrs, recoatable: 24 hrsFurther information on application can be found in the Technical Data Sheet under 'Downloads'.

A high-gloss, single-component yacht paint based on a non-yellowing, siliconized alkyd resin. The binder ensures long-lasting gloss retention, minimal dirt adhesion, and high color stability. EPIFANES NAUTIFORTE Yacht Paint is easy to apply and offers high coverage due to high-quality pigments. Suitable for new coatings on wood, steel, and aluminum in combination with a suitable primer, as well as for GRP surfaces. Also suitable for maintaining existing, intact 1- and 2-component coatings above the waterline, regardless of the manufacturer.Application: The substrate must be clean, dry, free of grease, and sanded. Application is done with a roller, soft long-haired brush, or spray gun at temperatures from 8–30 °C and relative humidity between 50–85%. Do not apply wet-on-wet and avoid excessively thick wet coats to prevent runs and drying problems. Recommended primers for substrate preparation are EPIFANES MULTI MARINE PRIMER (Art.No. 2066-175), for new aluminum EPIFANES WASHPRIMER AQ (Art.No. 2062-005). For a new coating, three coats are recommended, each with intermediate sanding (P400 or sanding fleece) by hand. Note on the color chart: The colors shown correspond as closely as possible to the original colors, but deviations cannot be ruled out.Technical dataApplication area: High-gloss, non-yellowing yacht varnish for wood, steel, aluminum, GRP above the waterlineSubstrate: Clean, dry, grease-free, sanded; in combination with suitable primerPrimer: EPIFANES MULTI MARINE PRIMER, EPIFANES WASHPRIMER AQ Coverage: approx. 14 m²/l at 40 µm dry film thicknessThinner: EPIFANES Paint Thinner (Art.No 2059-001), EPIFANES 1-K Spray Thinner (Art.No 2059-110) Application method: Brush, roller, spray gun (professional users)Drying times (at 20 °C): Dust dry: 1 hr, sandable and recoatable: 18 hrsFurther information on application can be found in the Technical Data Sheet under 'Downloads'.

EPIFANES MULTILUX is a high-gloss, non-yellowing 1-component white enamel based on siliconized alkyd resins. It is characterized by very good weather resistance, long-lasting gloss, fast drying, and good flow properties. Suitable as a topcoat for areas such as the bulwark or superstructures. Can be applied to gelcoat/GRP, steel, wood, and aluminum in interior and exterior areas above the waterline, as well as for repainting existing 1-C and 2-C coatings. On gelcoat, the paint can also be applied without primer if the surface is properly prepared.Application Apply with a long-haired, soft brush, roller, or spray gun at temperatures between 10 °C and 28 °C and relative humidity between 50 % and 75 %. Do not apply wet-on-wet, observe overcoating intervals. An intermediate sanding with P220 is recommended between coats. For long-term outdoor protection, at least 100–120 µm dry film thickness (approx. 3 brush coats or 4 roller coats) should be applied.Technical dataApplication area: Interior and exterior areas above the waterline Substrate: Intact, clean, degreased, and sanded 1-C or 2-C paints or primers; new gelcoat degreased and sandedPrimer: Common 1-C and 2-C primers such as EPIFANES MULTIMARINE PRIMER (Art.No. 2066-175)Coverage: approx. 13 m²/l at 40 µm dry film thicknessThinner: EPIFANES PAINT THINNER (Art.No. 2059-001), 1-C SPRAY THINNER (Art.No. 2059-110)Application method: Brush, roller, air spray (1.3–1.8 mm, 3 bar) or airless (0.013–0.015”, 140–160 bar)Drying times (at 20 °C): Dust dry: 1 h, sandable: 18 h, recoatable: 18 hFurther information on application can be found in the technical data sheet under 'Downloads'.

Classic, high-gloss graphite paint based on alkyd and urethane resins, e.g. for the hatch coaming and numerous other applications for interior and exterior use above the waterline. The coating is suitable for steel surfaces above the waterline and creates a smooth, dark metallic glossy surface. Due to the smooth and non-porous surface, dirt does not stick to it and the paint is easy to clean.Application: The surface must be clean, dry, grease-free, and sanded. For steel, a primer with a suitable primer such as EPIFANES MULTI MARINE PRIMER is recommended. Stir well before use. Apply with brush, roller, or spray gun at temperatures from 10 °C. Thinning is possible with EPIFANES PAINT THINNER or white spirit. Intermediate sanding between coats is recommended. Recoatable after approx. 18 hours at 18 °C.Technical DataArea of application: Glossy graphite paint for applications on steel surfaces above the waterlineSurface: Steel, clean, dry, grease-free, and sandedPrimer: EPIFANES MULTI MARINE PRIMER (Art.No. 2066-175) Coverage: approx. 12 m²/lThinner: EPIFANES PAINT THINNER (Art.No. 2059-001) or white spiritApplication method: Brush, roller, or spray gunDrying times (at 18 °C): Recoatable after approx. 18 hrsFurther information on application can be found on the product packaging.

A high-gloss, extremely hard 2-component finish coat based on saturated polyester resins and isocyanate with integrated UV filter. EPIFANES POLY-URETHANE YACHT COATING is particularly scratch-, impact-, and abrasion-resistant and offers very good weather and water resistance even in tropical climates. Suitable for wood, steel, aluminum, and GRP in interior and exterior areas above the waterline. Can be applied directly to thoroughly degreased and sanded polyester surfaces and is compatible with common epoxy and polyurethane primers.Application: The two components are mixed in a ratio of 2:1 (base:hardener, by weight) and ideally left to stand for 30 minutes (induction time). Application is done with brush, roller, or spray gun at temperatures from 10–30 °C and relative humidity between 50% and 75%. Do not apply wet-on-wet. Between coats, an intermediate sanding with P360–P400 is required if the next coat is not applied within 24 hours. Thinning is possible with EPIFANES PU BRUSH THINNER (Art.No. 2059-301) or PU SPRAY THINNER (Art.No. 2059-310).Custom color order: POLY-URETHANE YACHT COATING can be mixed in all RAL colors except metallics and fluorescent colors, and in all colors of the common maritime paint manufacturers from EPIFANES. The varnish is also available in satin gloss. Delivery time is approx. 10 days. Please specify the exact color shade at the very end of the ordering process under "Remarks".Technical dataApplication area: Non-working solid wood, plywood, steel, aluminum, and GRP above the waterlineSubstrate: Clean, dry, grease-free, sanded; GRP at least 14 days oldPrimer: EPIFANES EPOXY PRIMER or EPOXY HB COAT depending on materialCoverage: approx. 12–14 m²/l at 35–40 µm dry film thicknessThinner: EPIFANES PU BRUSH THINNER, PU SPRAY THINNER Application method: Brush, roller, or spray gun (professional users)Drying times (at 20 °C): Dust dry: 2 hrs, tack-free: 4 hrs, sandable and re-coatable: 24 hrsFurther information on application can be found in the technical data sheet under 'Downloads'.Safety note: Contains isocyanates. May cause allergic reactions. 

EPIFANES MULTIGUARD+ is a tar-free, semi-gloss black marine paint suitable for bare steel surfaces as well as for the maintenance of existing tar and bitumen coatings. The coating has excellent adhesion to steel as well as to pretreated tar and bitumen layers. The paint is colorfast and resistant to alternating influences of water and air. Application is by brush, roller, or spray gun. Application: Stir well prior to application. Make sure to apply the product only in well ventilated areas. The temperature should be above 8°C while applying and during drying times. The first coat is applied to bare steel or to roughened or softened tar layers thinned with 20–25% EPIFANES 1K Spray Thinner (Art. No. 2059-110) or white spirit and applied with a stiff bristle brush. Subsequent coats are applied with a short-haired lambskin roller. The substrate must be clean, grease-free, and dust-free. Existing tar layers should be prepared by high-pressure cleaning, degreasing, and roughening with grit 60 or a suitable solvent.Technical DataApplication area: Above and below the waterline on steel and woodSubstrate: Bare steel, wood, existing tar/bitumen coatingsPrimer: Not required if surface preparation is adequateCoverage: Approx. 5 m²/l at 100 μm dry film thicknessThinning: EPIFANES Paint Thinner; EPIFANES 1K Spray Thinner; EPIFANES D-100Application method: Brush, roller, spray application (professional users)Drying times (at 20 °C): Dust dry after approx. 15 minutes, tack-free after approx. 45 minutes, recoatable after approx. 12 hoursFurther information on application can be found in the Technical Data Sheet under 'Downloads'.

Transparent, glossy 1-component coating based on polyurethane resin for wood, plastic, and metal surfaces. COELAN Boat Coating Glossy is suitable for boat decks and all areas above the waterline.The product is UV-resistant, highly elastic, and remains breathable: water vapor can still diffuse from the coated material. Due to its extremely good weather resistance, long renovation intervals result. As a final coat (last layer), COELAN Boat Coating SILK MATT (matching articles) can also be applied. The boat coating can also be colored with COELAN color pastes (e.g., white, Art. No. 2622-1013).Application: The processing temperature should be between +5 °C and +30 °C. During processing and curing, ensure even ventilation, and personal protective equipment (gloves, respiratory mask) should be worn for safety. Depending on the substrate, pre-treatment with a suitable COELAN boat primer is required. Application is done in several even, generous layers with a brush or foam roller. For vertical surfaces, dilution with 10–30 % COELAN thinner is recommended. Depending on the area of use (walkable decks, masts, superstructures), 6-8 layers are required.Contains isocyanates. May cause allergic reactions. From August 24, 2023, appropriate training must be completed before industrial or commercial use (REACH Regulation Annex XVII)Technical DataArea of application: Transparent high-gloss coating for wood, plastic, and metal surfaces above the waterlineSubstrate: Requires COELAN boat primer depending on materialPrimer: COELAN boat primer (Art. No. 2620-001 or -101)Coverage: 1 l/m² Thinner: max. 30 % COELAN thinnerApplication method: Brush or foam rollerDrying times (at 23 °C, 50 % r.h.): Skin formation: approx. 2 hrs, walkable and recoatable: approx. 6 hrs, normally loadable: approx. 2 days, fully loadable: approx. 7 daysFurther information on processing can be found in the technical data sheet under 'Downloads'.

A transparent, semi-matt 1-component coating based on polyurethane. COELAN Boat Coating Silk Matt serves as a satin finishing coat on surfaces that have previously been coated with COELAN Boat Coating Gloss. The product is characterized by its durability, UV and weather resistance, high elasticity and abrasion resistance as well as easy cleaning.Application: Ideally, the product should be stored at room temperature for 24 hours before application and applied at temperatures between 5 °C and 30 °C. The coating is applied evenly with a foam roller or brush. Personal protective equipment such as gloves and a respirator must be worn during application. The product is ready to use, but can be adjusted with max. 30 % COELAN thinner if necessary.

COELAN Boat Primer is a 1-component polyurethane primer for the pretreatment of hardwood and softwood surfaces in conjunction with the transparent COELAN boat coating system. The pigmented glaze improves adhesion, provides a color match to the wood, and ensures a light-resistant base tint. It is slightly thixotropic (less dripping), quick-drying, and contains no biocides or fungicides. Available color shades:- yellowish translucent for softwoods and hardwoods such as teak, pine, fir, larch, spruce- reddish translucent for light-sensitive woods such as mahoganyApplication: The wood surface must be clean, dry, and free from separating substances. The processing temperature should be between +5 °C and +30 °C and a maximum of 80% relative humidity. The product is ready to use and should be stored at room temperature for approx. 24 hours before use.The primer is applied with a foam roller or brush to the sanded wood surface (grit 80). Tools can be cleaned with COELAN thinner (Art.No. 2629-001). During application and curing, ensure even ventilation, and personal protective equipment (gloves, respirator mask) should be worn for safety. Contains isocyanates. May cause allergic reactions. As of August 24, 2023, appropriate training must be completed before industrial or commercial use (according to REACH).Technical DataApplication area: Primer for hardwood and softwood in conjunction with COELAN boat coatingSubstrate: Clean, dry, sanded woodCoverage: min. 200 ml/m² (depending on absorbency, in several steps)Thinning: not recommendedApplication method: Foam roller, ring or flat brushDrying times (at 23 °C): Recoatable after approx. 2–3 hoursFor more information on application, please refer to the Technical Data Sheet under 'Downloads'.

Transparent adhesion promoter based on polyurethane resin for various interior and exterior plastic surfaces. COELAN Flexo Adhesion Primer is particularly suitable for reworking already hardened COELAN products based on polyurethane or epoxy resin, if these are to be further coated in color. Not suitable for substrates made of polyethylene (PE) or polypropylene (PP).Application: Existing COELAN polyurethane coatings must be cured for at least 7 days, epoxy resin coatings for at least 24 hours. Store the container at room temperature for approx. 24 hours before use. Apply the product evenly, thinly and over the entire surface using a cloth.

Thinner and cleaner for COELAN Boat Coating (e.g. Art. No. 2624-075). COELAN Thinner is added directly to COELAN Boat Coating as required to improve the application properties at lower temperatures or on vertical surfaces, for example. It is also suitable for cleaning tools immediately after application.

COELAN Color Pastes are suitable for coloring transparent, glossy COELAN Polyurethane Boat Coating (Art.No. 2621-075). The color pastes are ready to use and available in seven color shades. The opacity may vary depending on the color shade.Application: The color paste is stirred directly into the transparent COELAN Boat Coating in a maximum quantity of 10 %. Mix in the paste with a stirring rod or by machine with a slow-running agitator (max. 300 rpm). Once opened, tubes should be sealed airtight and used up promptly.Note on the color chart: The colors shown correspond as closely as possible to the original colors, but deviations cannot be ruled out.Technical dataArea of application: Coloring of COELAN polyurethane oatingsMixing ratio: max. 10 % addition to the coating quantityFurther information on processing can be found in the technical data sheet under 'Downloads'.

Transparent glass powder for full or partial scattering on COELAN coating systems to increase slip resistance. The product is suitable for all areas where increased slip resistance is required on coated surfaces. It is applied in combination with a fresh adhesive layer and is compatible with transparent and pigmented COELAN systems as well as all common 1- and 2-component coatings.Application: The product is sprinkled into the still tacky coating surface after painting &nbsp

Acrylic-based anti-slip coating from New Zealand: KIWI GRIP is excellently suited for creating slip-resistant and non-skid surfaces. The product is water-dilutable, single-component, and still resistant to environmental influences such as saltwater and UV radiation. The coating is available in four colors and comes in a resealable plastic pouch that allows for economical application. The color can also be tinted with water-based color pastes. Application:  Application should not be carried out in direct sunlight and high temperatures above 30°C to prevent unevenly fast drying. On non-absorbent substrates such as steel and fiberglass, a suitable primer is recommended. KIWI GRIP has a thick, yogurt-like consistency when undiluted, which, in combination with the texture roller, creates a coarse surface. By diluting the paint with water (up to 10%) or using, for example, fur rollers, the intensity and texture of the product can be individually adjusted.Before application, tape off the surface to be painted to create a clean edge. KIWI GRIP can be applied with a toothed spatula. Then work over with the included texture roller to create the rough surface. Remove the tape while the paint is still wet. The paint dries within a few hours but is only fully loadable after complete curing. Clean tools with water.The product is delivered in a practical plastic pouch including texture roller and application instructions. Technical DataApplication area: Non-skid acrylic-based deck coatingSubstrate: Fiberglass, wood, aluminum, and steel, clean, dry, grease-freePrimer: recommended for non-absorbent substrates (e.g. epoxy primer or EPIFANES MULTI MARINE PRIMER Art.No. 2066-175)Coverage: approx. 2 m²/l (undiluted)Thinning: Water (max. 10%)Application method: Texture roller or short-pile rollerDrying times (at 20 °C): dry after approx. 1 hr, re-coatable after approx. 4–6 hrs, fully loadable after approx. 2–3 daysFurther information on application can be found in the user brochure under 'Downloads'.

Single-component, semi-gloss deck paint based on urethane/alkyd resin. EPIFANES Non-Skid Deckcoating contains tiny polypropylene beads that form a non-slip surface after drying. Suitable as a non-skid topcoat on single-component paint systems on wood, steel, aluminum, or gelcoat/GRP.Application: Stir the paint thoroughly before and during use to ensure the beads are evenly distributed in the coating. Apply two coats with a short-haired velour roller without wet-on-wet application. Allow at least three days to dry before the first use. Color chart note: The displayed colors correspond as closely as possible to the original shades, but deviations cannot be ruled out for technical reasons. The color numbers of the non-skid deck paint are comparable to the color codes of EPIFANES MONO-URETHANE or EPIFANES Yacht Enamel, but color deviations may also occur due to the separate manufacturing process of the products.Technical DataApplication area: Non-slip deck coating for GRP, wood, steel, and aluminumSubstrate: existing single-component systems or after priming with EPIFANES coating build-upCompatible with: 1K paint systems, e.g. EPIFANES MONO-URETHANE (e.g. Art. No. 2055-175)Coverage: approx. 4–8 m²/l at 50 µm dry film thicknessThinner: EPIFANES Paint Thinner (Art. No. 2059-001) or EPIFANES 1-K Spray Thinner (Art. No. 2059-110)Application method: short-nap velour rollerDrying times (at 15 °C): dust-dry: 2 hrs, recoatable: 36 hrs, loadable: after at least 3 daysFurther information on application can be found in the Technical Data Sheet under 'Downloads'.

A silk-matt, one-component polyurethane resin-based coating that can be used as an anti-slip top coat indoors and outdoors.The coating has a double anti-slip effect due to the granules it contains and the rough texture when it dries. OWAGRIP was specially developed for the extreme weather conditions in the maritime sector, is abrasion-resistant, UV-resistant and anti-corrosive. Can be applied to existing polyurethane, epoxy, alkyd and acrylic-based paint systems.Application: Clean the substrate well before painting, sand the surface if necessary and repair any damage accordingly. For recoating untreated wooden surfaces or slightly rusting metal surfaces, 5-10% Owatrol oil can be added for the first coat. Stir well before use. Technical DataApplication area: anti-slip coating for decks, walkways, stairs, rampsSubstrate: clean, dry, sound; suitable for wood, GRP, aluminium, steel, old coatingsApplication: short nap roller (6–8 mm), airless spray, conventional spray gunCoverage: approx. 7–8 m²/l (undiluted), approx. 10 m²/l (with max. 10% thinner)Thinner: max. 10% OWATROL OilApplication temperature: +10 °C to +30 °CDrying (20 °C): dust dry after 2 hrs, touch dry after 6 hrs, recoatable after 24 hrsFurther information on application can be found in the Technical Data Sheet under "Downloads".

The Antislip Additive from PPG SIGMA is a finely ground natural granulate made from coconut shells for producing slip-resistant coatings for decks and walkways. The powder consists of coconut shell fibers and is compatible with all top coat from PPG SIGMA and other manufacturers. It is especially suitable for applications where increased slip resistance is required.Application: The powder can be stirred directly into the topcoat and applied with a short-pile roller. Alternatively, it can be sprinkled onto the fresh paint layer – ideally using a fine sieve. The exact dosage depends on the desired slip resistance and the amount of paint used.Technical DataApplication area: Production of slip-resistant deck paintsSubstrate: depends on the paint system usedCoverage: approx. 50 g per liter of paintApplication method: Mixing into the paint or sprinkling onto the fresh coatingGranule size: irregular, fibers up to approx. 3 mm in lengthFor more information on application, refer to the product packaging or contact the manufacturer.

Transparent glass powder for full or partial scattering on COELAN coating systems to increase slip resistance. The product is suitable for all areas where increased slip resistance is required on coated surfaces. It is applied in combination with a fresh adhesive layer and is compatible with transparent and pigmented COELAN systems as well as all common 1- and 2-component coatings.Application: The product is sprinkled into the still tacky coating surface after painting &nbsp

Powdered additive made from high-quality polypropylene beads for creating non-slip surfaces in combination with one- and two-component paints from EPIFANES (e.g., EPIFANES Mono-Urethane Art.Nr. 2055-175 or Poly-Urethane Paint Art.Nr. 2063-800). The grain size of approx. 130 µm ensures an even distribution in the coating. The white powder takes on the color of the paint used after stirring in.Application: The anti-slip additive is stirred into the paint and then left to rest for 10-15 minutes. One can of 20 g anti-slip additive is sufficient for 750 ml of paint. During application, the paint should be stirred regularly to ensure an even distribution of the additive. Application is best done with a short-pile velour roller or a paint roller. The treated surface should then dry for at least 72 hours before being subjected to load.Technical DataApplication area: Additive for creating non-slip paint surfaces Compatible with: all common 1K and 2K paints (clear and colored paints)Coverage: 20 g per 750 ml of paintGranule size: 130 µmApplication method: short-pile velour roller, paint smoothing rollerDrying times (at 20 °C): min. 72 hrs before initial load

The self-adhesive DECKSTRIP anti-slip strips from PSP Marine offer good grip on decks, stairs, jetties, and other smooth surfaces even when wet, thanks to their textured surface. The strips are made from a polymer-coated, textured backing material. The back is coated with a strongly adhesive acrylic glue, allowing for easy installation without additional tools or adhesives. The adhesive strips are UV-resistant, waterproof, and suitable for both indoor and outdoor use. The DECK STRIP is available in black or white  and is suitable for GRP, wood, aluminum, or steel. Each package contains two sheets, each with five pre-cut strips with rounded corners.Application: The surface must be clean, dry, smooth, and free of grease. The strips are pre-cut but can be individually trimmed with scissors or a knife. After removing the protective film, the strip is pressed down evenly. Final adhesion is achieved after 24 hours. The strip can be removed without leaving any residue. Technical DataApplication area: Slip resistance on smooth surfaces indoors and outdoorsSurface: GRP, wood, metal; smooth, dry, grease-freePrimer: not requiredCoverage: 10 strips per packageInstallation: self-adhesive, can be applied by handDrying times: tack-free immediately, final strength after approx. 24 hrs

Fine-grained polypropylene-based additive for the production of anti-slip deck coatings. HEMPEL ANTI-SLIP PEARLS&nbsp

"TONKI" - the classic! Glossy, clear varnish oil for wood and metal. The formulation of LE TONKINOIS varnish oil is based on a special formula in which high-quality linseed oil and Chinese wood oil (tung oil) are cooked together. This creates a natural product without chemical additives. The varnish oil is suitable for indoor and outdoor use as well as for application under extreme weather conditions. It forms a resistant, elastic protective film with high UV resistance and highlights the natural grain of the wood.Application: LE TONKINOIS VARNISH is applied to untreated or cleanly sanded wood. Application is done with a brush or roller; for spray application, it can be diluted up to max. 10% with the appropriate LE TONKINOIS thinner. Only one thin coat should be applied per day. Stir well before use, do not apply below 12 °C.Technical DataArea of application: Wood and degreased metals indoors and outdoors, also under extreme weather conditionsSubstrate: Untreated wood, wood-based materials, limited use on corkCoverage: 20 m²/l Thinning: Max. 5–10% with LE TONKINOIS thinnerApplication method: Brush, flat brush, sprayingDrying times (at 20 °C): Dust dry after 6–8 h, reworkable after approx. 24 h, walkable after 3 days (with 2–3 coats)Further information on application can be found in the technical data sheet under 'Downloads'.

Zinc dust-containing (67%), surface-tolerant 2-component epoxy primer with high penetration properties, even on steel surfaces that have only been derusted by hand or water-blasted. The pigment-rich formulation results in a very well adhering and robust cathodic corrosion protection layer for use above and below water.HANSAZINC ST tolerates residual moisture (no wetness) and slight flash rust formation. Can be painted over with two-component paints as well as with bitumen, vinyl and chlorinated rubber primers, but not with alkyd resin-based paints and paints containing zinc phosphate. Not suitable for use on galvanized, stainless, light or non-ferrous metals, wood, mineral substrates or plastics.Application: The mixing ratio is 93:7 (base:hardener) by volume. The pot life is 3-4 hours. Depending on the substrate, the product can be applied by spraying, brushing or rolling. On hand-rusted surfaces, the coating must be worked in intensively; a bristle brush is best suited for this. Ideal processing and surface temperatures are between 15 °C and 25 °C and at least 5 °C above the dew point.&nbsp

Premium primer that combines the properties of a rust protection primer and an air-drying natural oil with high solids content and exceptional penetrating properties. Thanks to the formulation with OWATROL oil, OWATROL CIP has a low surface tension and is three times "wetter" than water. This allows it to optimally wet surfaces and penetrate even hard-to-reach corners that may not be mechanically derusted. It penetrates thick rust layers down to the "sound" metal and displaces moisture and air.The oil dries completely, even in thick layers given sufficient drying time. After drying, it remains elastic but is hard enough due to the added primer to be coated with a subsequent one- or two-component system such as an epoxy or chlorinated rubber primer. Suitable for all areas exposed to extreme climatic conditions, such as ballast tanks. Active ingredients: water-displacing penetrating oil and iron oxide.Technical DataSubstrate: Iron, steel, cast iron, stainless steel, light metals (bare or rusted)Surface preparation:Remove loose paint and rustFirm rust may remainSurface must be dry, grease-free and cleanFor chemically exposed surfaces: thorough cleaning with water or steamTopcoat: All one- or two-component systems including epoxy, polyurethane, chlorinated rubber etc.Coverage: up to 15 m²/l (depending on substrate and rust depth)Thinner: noneApplication method: Brush, lambskin roller, spray gun (professional use)Drying times at 20 °C: Touch dry after approx. 6 hrs; recoatable after 48 hrs.Further information on applying this product can be found in the technical data sheet under “Downloads”.Safety note: Cloths soaked with drying oils can self-ignite, therefore always spread out to dry before disposal or collect in sealed metal containers.

Classic metal preservation from the commercial shipping industry. HANSALUX U SCHIFFSBODENÖL is an aromatic-free, high-solids coating based on linseed oil and a special alkyd resin. It is suitable for wooden substrates and hand-rusted steel surfaces above water.This aromatic-free preservative is primarily used where sandblasting and the use of a rust machine are out of the question, such as on inboard walls, in the bilge or in the anchor locker.&nbsp

OWATROL OIL, which is based on natural oils and has exceptionally good penetration properties, is the basic product for many applications.It is three times wetter than water, i.e. it even creeps upwards. On rusty metal, it creeps deep into the rust pores and displaces the air and moisture (i.e. the actual cause of corrosion) even from inaccessible areas. After drying (24 hours at 20°C), the leaf rust can be removed more easily and the soaked residual rust is consolidated, preserved, sealed and can be painted with all turpentine substitute thinnable paints.OWATROL-OIL is also ideal as an additive (color additive) for 1-component paints. Instead of using turpentine substitute as a thinner, it significantly improves the coating and flow properties and ensures optimized adhesion without compromising the quality of the paint. On the contrary, the addition of 10-15% OWATROL OIL makes paints and varnishes even more porous and durable on the surface.OWATROL spray is suitable for minor touch-ups.Technical dataSubstrates: Rusty and bare metals (iron, steel, aluminum), new and weathered woodPre-treatment: depending on the material: remove loose rust, non-adherent old paint, oil and grease

Thixotropes Rostschutzmittel auf Lanolin-Basis in der Sprühdose, das zugleich als Rostlöser und Gleitmittel wirkt. FLUID FILM AS-R SPRAY bildet einen klaren, glänzenden Schutzfilm und eignet sich zur Konservierung und Pflege von Metalloberflächen in Fahrzeugen, Booten, Maschinen und Haushaltsgeräten.Das Produkt wird durch Regen und Seewasser weder abgewaschen oder verändert, außerdem verhält es sich temperaturstabil und ist äußerst widerstandsfest gegen alle Witterungseinflüsse, auch Schnee.  Im Gegensatz zu herkömmlichen Produkten ist FLUID FILM AS-R durch seine lösungsmittelfreie Zusammensetzung umweltfreundlicher und sparsamer im Gebrauch. Die Sprühflasche enthält FLUID FILM NAS mit Propan-Butan als Treibgas.Anwendung: Untergründe von losen Verschmutzungen befreien, Flächen können trocken oder feucht sein, jedoch ohne Oberflächenwasser. Gleichmäßig aufsprühen, auch in schwer zugänglichen Bereichen mit Sprühröhrchen. Dose sprüht in jeder Lage. Anwendung bei Bedarf wiederholen. Sicherheitsvorschriften beachten: Dose steht unter Druck, nicht über 50 °C erhitzen, nicht ins Feuer sprühen, brennbar.Technische DatenAnwendungsbereich: Fahrzeuge, Boote, Industrieanlagen, Werkzeuge, Maschinen, Waffen, Freizeit- und HaushaltsgeräteUntergrund: Trockene oder feuchte Oberflächen, frei von losen VerschmutzungenViskosität: niedrig (wie Sirup)Ergiebigkeit: Abhängig von Objektgröße und AnwendungApplikationsmethode: Sprühen mit Standarddüse oder SprühröhrchenTrocknungszeiten (bei 20 °C): Kriechend und haftend, bildet nach kurzer Zeit einen beständigen SchutzfilmWeitere Informationen zur Verarbeitung finden Sie im Technischen Datenblatt unter 'Downloads'.

OWATROL GELCOAT RESTORER, also known as POLYTROL, is a tried and tested color refresher for metals, plastics, paints and gelcoats.The product refreshes faded colors of plastic or gelcoat surfaces, regenerates faded surfaces of marble, tiles or slate and restores shine to dull surfaces without leaving a greasy or oily film.The product is acid- and silicone-free, extremely penetrating and penetrates deep and sealing into microporous surfaces.Also suitable for the care of brass, bronze and stainless steel fittings.Application: Apply and spread evenly with a brush or clean cloth, spray from a distance of approx. 30 cm. After a maximum of 10 minutes, rub the surface dry with a absorbent, lint-free cloth, removing any excess product.Technical DataApplication area: Restores color and gloss on weathered plastic, gelcoat, paint, metal, plastic partsSubstrate: dry, clean, grease-freeApplication: cloth or lint-free rag; remove excess within 20 minCoverage: approx. 18 m²/l (depending on porosity and surface)Thinner: noneApplication temperature: +5 °C to +35 °CDrying (20 °C): fully dry after 24 hrs; no buffing requiredFurther information on application can be found in the Technical Data Sheet under "Downloads".

Penetrating oil based on natural oils, which is used as an additive to improve the flow properties of conventional and semi-synthetic paints. It reduces visible brush strokes, impregnates wood and has a rust-inhibiting effect on steel by penetrating deep into the substrate. This means that a favorable result can be achieved even under difficult conditions.

WICHINOX PASSIVATION GEL from french manufacturer WICHARD is a cleaning and passivation agent for the maintenance of stainless steel parts in maritime and industrial environments. The gel formulation makes application easier even in hard-to-reach areas and ensures effective restoration of the protective passive layer on stainless steel.The product helps to remove tarnished surfaces and light corrosion marks on stainless steel fittings from Wichard, as well as other stainless steel components such as stanchions, handrails, or fenders. Application: Dismantle the parts to be treated if possible to avoid damaging adjacent surfaces. Ensure adequate ventilation and appropriate protective measures (e.g. gloves, safety goggles) during use. Stir before use. Apply the gel to the stainless steel surfaces to be treated with a brush and allow to act for 5–15 minutes. After the exposure time, rinse thoroughly. Do not apply to galvanized, painted, or anodized surfaces. Safety Note: Contains phosphoric acid. Harmful if swallowed. Causes severe skin burns and serious eye damage.Further information can be found in the Technical Data Sheet under 'Downloads'.

FLUID FILM LIQUID A is a transparent, solvent-free, oil-based corrosion protection based on lanolin (wool grease) for soft coating of steel surfaces in above and underwater areas.The product displaces water, penetrates existing rust, and forms an elastic, adhesive protective film. It was originally intended for flooding repair-needed ballast water tanks on ships, floating docks, offshore units, for flooding coating of cavities, ballast water tanks, offshore structures, and hard-to-reach areas. The protective film lasts up to two years in enclosed cavities. Additionally, it is suitable for loosening seized rust or making rusted metal parts movable. Application on damp or slightly corroded surfaces is also possible.The product contains no solvents, is environmentally friendly, and easy to apply. Available as spray (type AS-R), in cans or containers (for dipping, spraying, or brushing).Application: Application is carried out depending on the area of use by flooding, brushing, rolling, or spraying. The material should be homogenized before use. After application, the gel time when flooding is about 3–4 hours. Application is possible at any temperature. Ensure adequate ventilation and personal protective equipment.Technical DataField of application: Single-layer corrosion protection on steel surfacesSubstrate: Steel (bare, rusty or damp); no special pretreatment necessaryPrimer: not requiredCoverage: approx. 12 m²/l at 80 µm wet film (roller, brush application)Thinning: not necessaryApplication method: Brush, roller, spraygun, flooding (professional users)Drying times: none; forms a non-drying, oily protective filmFor more information on application, refer to the technical data sheet under 'Downloads'.

OWATROL OIL, which is based on natural oils and has exceptionally good penetration properties, is the basic product for many applications.It is three times wetter than water, i.e. it even creeps upwards. On rusty metal, it creeps deep into the rust pores and displaces the air and moisture (i.e. the actual cause of corrosion) even from inaccessible areas. After drying, the leaf rust can be removed more easily and the soaked residual rust is consolidated, preserved and sealed for the long term and can be painted with all turpentine-substitute thinnable paints.For use on larger surfaces or as a paint additive, OWATROL is suitable for painting from the can.Technical dataSubstrates: Rusty and bare metals (iron, steel, aluminum), new and weathered woodPre-treatment: depending on the material: remove loose rust, non-adherent old paint, oil and grease

Highly penetrating, acid-free universal oil in a practical spray bottle for precise dosing.OWATROL TRANSYL is an excellent screw remover, displaces moisture, breaks down rust and prevents new rust formation. A good lubricant that does not attack substrates such as metals, plastics and paints.Application: Shake spray thoroughly before use. Do not spray on hot surfaces. Cover adjacent areas. Spray the product onto the areas to be treated, either selectively or over the entire surface &nbspTechnical DataApplication area: Metal connections, bolts, hinges, bearings, guidesSubstrate: rusty or bare metal, plastics, paintApplication: spray canCoverage: depends on usage (spot or area-wide)Thinner: noneApplication temperature: –30 °C to +50 °CDrying (20 °C): very slow evaporation, leaves lasting lubricating filmFurther information on application can be found in the Technical Data Sheet under "Downloads".

Solvent-free, soft coating material based on lanolin (wool fat). FLUID FILM Gel BN is a physiologically safe and environmentally friendly corrosion protection agent. It serves as a single-layer long-term protective coating for ships, docks, offshore units, and similar objects when surface preparation is limited to high-pressure washing. The viscous gel can be used as a lubricant for machines, equipment, winches, and for wire rope preservation. The product offers excellent corrosion protection, lasting up to 20 years in enclosed spaces. It penetrates residual rust, and promotes the self-healing effect in case of damage to existing coatings. FLUID FILM Gel BN is temperature stable from -45 °C to +70 °C. Complies with MIL-Spec C-23050 guidelines. Preparation: Loose components, dirt, rust, and standing water must be removed before application. Surfaces must be dry.Application: FLUID FILM Gel BN can be applied using a brush, roller, spatula, or airless spray. The greater the layer thickness, the better the corrosion protection. Due to its gel-like consistency, thicker layers up to 1000 µm can be applied. The material can be used directly from the container. For areas with strong water turbulence, it is recommended to subsequently apply an additional layer of PERMA FILM (Art.No. 2718-501). Technical DataApplication area: Long-term protection for ballast tanks, voids, offshore structures, and metal partsSubstrate: Clean, dry, free from loose components; high-pressure cleaning recommendedLayer thickness: 600–1000 µm (airless spraying), 80 µm (brush/roller)Coverage: approx. 1.6 m²/l (at 600 µm), approx. 12 m²/l (at 80 µm)Application temperature: -10 °C to +40 °CApplication methods: Brush, roller, spatula, airless sprayingColor: Transparent (Gel BN)Temperature resistance: -45 °C to +70 °CFurther information on application can be found in the Technical Data Sheet under 'Downloads'.

The BALLISTOL PTFE Dry Lubrication Spray is suitable for clean dry lubrication of sensitive areas. It is free from oil, grease, and silicone. Finest PTFE particles adhere even to microscopically small surface irregularities, thereby reducing adhesion, sliding, and rolling friction, and protecting against dirt and dust deposits. The spray is highly compatible with materials and suitable for all common materials.The spray is suitable for consistent and long-lasting lubrication of rollers and bearings, sliding guides and rails, cable pulls and telescopic guides, gears and cogs, as well as plastics of all kinds.Application: Shake well before use. Spray the product onto the cleaned surface from a distance of 10–25 cm and allow it to dry for a few minutes. A barely visible, dry film remains.Hazard information: Extremely flammable aerosol. Container is under pressure: it may burst when heated above 50°C. Causes serious eye irritation. Further information can be found below under "Downloads & Information".Technical dataApplication area: Dry lubrication in guides, bearings, gears, cable pulls, plastic and metal jointsSurface: Metal, plastic, rubber – clean, grease-free, dryPrimer: not requiredYield: dependent on application area (spray application)Thinning: not requiredApplication method: Aerosol sprayDrying times: short, depending on ambient temperatureFurther processing information can be found in the technical data sheet under 'Downloads'.

BALLISTOL UNIVERSAL OIL is a biodegradable, skin-friendly multifunctional oil for cleaning, maintenance, lubrication, and corrosion protection. The oil has been manufactured since 1904 using an unchanged formula and is based on a mildly alkaline composition with lanolin and is free of silicone, PTFE, and acid. It does not resinify and is emulsifiable in water.Usable in industry, shipping, agriculture, household, outdoor activities as well as for machines, tools, leather, wood, rubber, and even for use on humans and animals.Application: BALLISTOL Universal Oil can be used as a rust protection, lubricant, penetrating or contact oil. It dissolves tar, grease, adhesive residues, and other unsuitable oils, neutralizes weak acids (e.g. hand sweat), and is suitable for the care of leather, natural wood, and oil-resistant plastics. Application is done with a cloth or brush. Technical DataApplication area: Corrosion protection, lubrication, cleaning, maintenanceSubstrate: Steel, iron, leather (except suede), natural wood, rubber, plasticCoverage: depends on application method Thinning: not requiredApplication method: cloth, brushDrying times: not applicable; remains active and does not resinifyFor more information on application, please refer to the Technical Data Sheet under 'Downloads'.

Universal marine grease for the many lubricating points on board, water-repellent, saltwater resistant and stable to ageing and liquefying.

Permanently elastic, slow-drying, single-component thick grey film paint that can be applied to surfaces preserved with FLUID FILM Liquid A and prevents washout. This calcium phosphate compound dissolved in resin provides effective corrosion protection for all bare, rusted, or previously painted ferrous metals. PERMA FILM AL is suitable for ballast water tanks, offshore structures, machine components, and hard-to-derust areas such as the bilge.The lamellar pigment structure forms a barrier against water and oxygen, even on incompletely derusted or damp substrates. The paint can also be applied at low temperatures and is particularly resistant to saltwater.Surface preparation: Clean the surface (high-pressure wash) and remove loose particles with a wire brush. Surfaces may be surface damp but without water droplets. A thin coat of FLUID FILM LIQUID A is recommended as a primer. This combination keeps the system flexible, cures on the surface, and combines the positive properties of FLUID FILM’s penetration capability with those of a solid protective layer.Application: The product can be applied by airless spraying, brush, or roller. PERMA FILM can be processed directly from the container; thinning is not necessary at temperatures above 15 °C. For a new coating, apply two layers; the first with 150, the second with 250 µm wet film thickness (equivalent to 100 and 150 µm dry film thickness).During application and drying, sufficient ventilation must be ensured to guarantee uniform drying. A respirator must be worn when spraying. The drying process can be accelerated by using warm air.Technical DataApplication area: Coating of ballast water tanks, offshore installations, machines, equipment, steel surfacesSubstrate: Steel, also hand-derusted (St 2/St 3) or HD-cleaned (Wa 2); dry or damp surfacesPretreatment: optional: FLUID FILM LIQUID A (Art.No. 2717-001) Coverage: approx. 2.5 m²/l at 250 µm dry film thicknessThinning: optional, at temperatures below +15 °C: Special cable cleaner PF-SolventApplication method: Brush, roller, airless (professional users)Drying times (at 20 °C): water-resistant after approx. 30 hrs at 200 µm film thicknessFurther information on application can be found in the Technical Data Sheet under 'Downloads'.

The Zinc Spray from EURO LOCK offers a fast-drying corrosion protection with excellent long-term effect for all metals. It is suitable for use on thermally stressed parts such as intake manifolds, heat exchangers, oil coolers, etc. It is electrically conductive and heat resistant up to 500 °C.Additionally, it is suitable for reworking or repairing defects on hot-dip galvanized parts, and for touching up damaged zinc coatings.Also suitable for refreshing galvanized anchors, anchor chains, and for repairing welding and sheet metal work. Prevents rust and provides good protection against extreme weather conditions. Zinc content approx. 95% in the dry film. Can be overpainted with most one- and two-component primers and paints.Technical DataSubstrates: All metalsPretreatment:Surface must be clean, dry, free of grease and oilShake can well for approx. 2 minutes before useTest spraying recommendedSubsequent coating: Can be overpainted with many paint systems (own testing recommended)Coverage: No informationApplication method: Spray from approx. 20–30 cm distance in a crisscross patternDrying times at 20 °C: Dust-dry after approx. 8 min; tack-free after 20–30 min; fully dry after 48 hrsFurther information on application can be found in the technical data sheet under "Downloads".

BALLISTOL UNIVERSAL OIL is a biodegradable, skin-friendly multifunctional oil for cleaning, care, lubrication and corrosion protection. The oil has been produced according to the same recipe since 1904 and is based on a slightly alkaline formula with lanolin and is free from silicone, PTFE and acids. It does not resinify and can be emulsified in water.Can be used in industry, shipping, agriculture, household, outdoor activities as well as for machines, tools, leather, wood, rubber and even for use on humans and animals.Application: BALLISTOL Universal Oil can be used as a rust protection, lubricating, penetrating or contact oil. It dissolves tar, grease, adhesive residues and other unsuitable oils, neutralizes weak acids (e.g. hand perspiration) and is suitable for the care of leather, natural wood and oil-resistant plastics. It is applied by spraying &nbsp

Quick-drying, solvent-based stain for coloring and tinting wood, available in reddish mahogany and reddish-brown teak.The stain is characterized by very long-lasting colour stability and can be painted over with most 1- and 2-component paint systems.Application: Shake can very well before use. Do not dilute. Apply the stain thinly and evenly in the direction of the grain. Up to three coats can be applied to increase the color intensity. After drying, the stain can be coated with all common clear coats, e.g. EPIFANES boat varnish or DD-POLY-URETHANE varnish.To conceal or even out color differences in existing clear coat systems, the stain can be mixed with up to 10 % of a clear coat to achieve uniform pigmentation. Can also be used for coloring WEST SYSTEM Epoxy &nbsp

LE TONKINOIS Yacht Oil Stain is a plant oil-based, intensely colored wood pre-treatment for hardwood surfaces indoors and outdoors. The stain penetrates deeply into the wood and creates a uniform coloration with a pleasant feel. It is resistant to dirt and water-repellent, and the pigmentation increases UV protection. In boatbuilding it is suitable for matching the color of wooden surfaces on decks, superstructures and other heavily used surfaces. For adequate protection, a subsequent protective coating with LE TONKINOIS Vernis or Marine No.1 is recommended.Application: The surface must be dust- and grease-free and clean; the wood moisture should not exceed 15%. The stain is applied undiluted with a brush or roller to untreated wood. After a short exposure time, the excess is evenly distributed and removed with a lint-free cloth. It is recommended to create a test area beforehand. The processing temperature should be at least 12 °C. Walkability is achieved after three days with 2–3 coats.Technical DataField of application: Indoor and outdoor, e.g., boat decks, superstructures, wooden floorsSubstrate: Untreated wood, wood-based materialsCoverage: 35–50 ml/m² (depending on type of wood)Application method: Brushing with brush or rollerDrying times (at 20 °C): Dust-dry after 6–8 h, re-coatable after 12 h, walkable after 3 daysFor more information on processing, please refer to the technical data sheet under 'Downloads'.

HENSOTHERM fire protection paint is an insulating coating for wood according to DIN 4102 Part1. When exposed to heat, it forms a heat-insulating foam layer on endangered wooden surfaces such as in the engine room or galley of wooden yachts and traditional ships. HENSOTHERM is already approved as a fire protection system on numerous traditional ships.HENSOTHERM 1KS is colorless and is only suitable for basically dry interior areas. For a colorless, transparent coating in these areas, the wood is first primed with wood primer AQ to minimize absorbency. Then the insulating HENSOTHERM 1KS is applied and finally sealed with the topcoat HENSOTOP 84AF to achieve a certain abrasion resistance.In areas on board where high humidity or condensation can occur, the waterproof, gray, exterior paint HENSOTHERM 2KS must be used and afterwards sealed with the waterproof, white topcoat HENSOTOP SB. HENSOTOP SB is available in a wide range of colors on request and at extra cost. Unfortunately, transparent fire protection in areas subject to moisture is not possible.

Heat-resistant, single-component paint for the protection and enhancement of steel and iron surfaces exposed to temperatures of 400-1000°C, such as exhaust systems. Application: The surface should be dry, clean, and free of grease. Remove rust and loose parts. The paint is applied in a thin layer directly onto bare steel. After the paint has dried, the surface must be heated to at least 400°C to cure the binder.Safety note: Do not touch the surface (even when cold), the paint has a caustic effect.Technical dataApplication area: Heat-resistant paint for metal surfacesSubstrate: Steel, (cast) iron exposed to high temperaturesCoverage: approx. 12 m2/l.Thinner: EPIFANES paint thinner (Art.No. 2059-001)Application method: Brush, rollerDrying times (at 20°C): dust-dry after 15 min., tack-free after 1 hr., re-coatable after 12 hrs.

A solvent-free, two-component insulating coating based on epoxy resin for use on cooling and ice containers as well as water tanks. VENEZIANI ECOPLAST is approved for food use and therefore suitable for contact with drinking water, fresh and frozen fish, mussels, crustaceans, etc.The product can be applied to all boat building materials with appropriate preparation and has high chemical resistance. It complies with standards D.M. 21/3/1973 (relating to the hygiene of packaging, containers and equipment in contact with food) and DM 06/04/2004 n.174 (concerning materials and equipment used in plants for the collection, treatment, supply and distribution of drinking water for human consumption).Application: Clean, degrease and if necessary sand the substrate. Stir base and hardener separately, then mix in a volume ratio of 3:2 (or by weight 2:1). Apply with a brush or short-haired roller. For new coating, two coats are recommended. When working indoors, ensure adequate ventilation. Use personal protective equipment (work clothing, safety glasses, gloves, mask).Application on aluminum tanks: Direct application on aluminum with VENEZIANI ECOPLAST is not possible. A non-binding recommendation for applications on aluminum is apply an adhesion primer like the epoxy high-build primer VENEZIANI ADHERPOX (Art.No.2519-152). First, thoroughly degrease the surface. Then apply several coats of VENEZIANI ADHERPOX with a roller or brush until a dry film thickness of at least 300 µm is achieved. Afterwards, VENEZIANI ECOPLAST can be applied.Technical DataApplication areas: Cooling and ice containers, water tanks, food-safe surfacesSurface preparation: Wood: Prime with FibrodurGelcoat: degrease, rinse, sand, cleanSteel: sandblast to Sa 2½ or machine sand to grade 3Primer: For new wood use Fibrodur primerMixing ratio: 3:2 (by volume)Coverage: Approx. 6.7 m²/L at 150 µm dry film thicknessThinning: No thinning; clean tools with thinner 6610Application method: Brush or short-haired rollerPot life (at 20°C): approx. 50 min.Drying times (at 20 °C): Recoatable after 8–24 hrs; fully cured in 7 days; For further processing information, please refer to the Technical Data Sheet under 'Downloads'.

Aromatic-free brush thinner with high dilution power for most single-component primers, paints, and varnishes; very pure due to double distillation.Application: only stir the paint thinner into the varnish or paint in small amounts if necessary and mix thoroughly. Do not dilute more than necessary; excessive addition can cause runs and reduce the dry film thickness. Use only the thinners recommended by the manufacturer. Read the label/product information or safety data sheet before use.Technical DataApplication area: Dilution of 1K primers, paints, and varnishes; designed for brush/roller applicationApplication method: Add to the respective 1K coating, designed for brush/roller processing

Balsam turpentine oil is a high-quality, pure natural product with strong dissolving power, obtained by distillation from the turpentine (balsam) of coniferous trees such as pinetrees. It is transparent, mildly scented, and suitable as a thinner for paints and varnishes based on oil and oil-alkyd resins. It can also be used to dissolve natural resins and oils. Application: The balsam turpentine oil can be added according to the paint manufacturer's instructions. Storage should be cool but frost-free. The container must always be tightly sealed.Safety instructions: The product is highly flammable and harmful if swallowed, in contact with skin, or if inhaled. Ensure good ventilation during use, avoid aerosol formation, and keep away from sources of ignition. Technical dataApplication area: Thinner for oil and oil-alkyd resin paintsSubstrate: depending on the paint system usedCoverage: depending on the type of paint and desired viscosityDrying times: depending on the paint usedFor further information on application, please refer to the technical data sheet under 'Downloads'.

LE TONKINOIS GELOMAT is a matting agent for combination with all LE TONKINOIS lacquers. It is added to the last coat of lacquer to achieve a satin to matt surface. Depending on the mixing ratio, different gloss levels such as matt, silk matt or silk gloss can be achieved.Application For a matt surface, mix LE TONKINOIS GELOMAT and lacquer in a ratio of 1:1. For silk matt results, use a ratio of 1:2, for silk glossy surfaces, use a ratio of 1:3. Ensure good ventilation during application. The drying time corresponds to that of the paint product used.Further information can be found in the technical data sheet under 'Downloads'.

LE TONKINOIS Thinner is a universally applicable thinner for all solvent-based LE TONKINOIS products, linseed oil varnish (Art.No. 2691-001), as well as for cleaning brushes and tools, degreasing surfaces, and removing resin or wax contaminants. Application: Always ensure good ventilation during use. LE TONKINOIS Thinner can be used both for targeted thinning during application and for cleaning purposes. Ingredients: IsoaliphaticsFurther information on application can be found in the technical data sheet under 'Downloads'.

A fast evaporating thinner for spray applications of EPIFANES POLY-URETHANE Yacht paints and varnishes.

INTERNATIONAL THINNER No.1. is a universal thinner for one-component products (except Primocon and antifoulings) and for varnishes.Technical dataArea of application: Thinning of INTERNATIONAL 1K productsCompatible with: INTERNATIONAL ORIGINAL Art.No. 2550-001), COMPASS (Art.No. 2550-076), SCHOONER (Art.No. 2550-073)

Special thinner for Epifanes 2-component polyurethane paints. Developed for use at higher ambient temperatures to delay drying speed and ensure even flow of the coating.Application: Use only for Epifanes 2-C-PU products. Add to the paint in small amounts to achieve the desired viscosity. Especially suitable for high temperatures or large-area coatings. Observe safety and handling instructions on the container and safety data sheet.Technical DataApplication area: Thinning Epifanes 2-C polyurethane paints at high temperaturesApplication method: Add to the paint mixture in the dosage recommended by the manufacturer

Colorless, aromatic-free special thinner for spray application of Epifanes 1-component varnishes, primers, and paints. Developed to achieve the correct spray viscosity.Application: Use only for spray application of Epifanes 1-C products. Add thinner in small amounts until the recommended spray viscosity is achieved. Do not overdose, as this can negatively affect drying and film thickness. Observe the safety and processing instructions on the product packaging.Technical DataApplication area: Thinner for spray application of Epifanes 1-C varnishes, primers, and paintsApplication method: Add to Epifanes 1-C products to adjust spray viscosity

Penetrating oil based on natural oils, which is used as an additive to improve the flow properties of conventional and semi-synthetic paints. It reduces visible brush strokes, impregnates wood and has a rust-inhibiting effect on steel by penetrating deep into the substrate. This means that a favorable result can be achieved even under difficult conditions.

Special thinner based on aromatic hydrocarbons for the application of polyurethane coatings, single-component paints, and epoxy resin systems. THINNER 21-06 is also suitable for cleaning tools and equipment before and after application.Application: Use only in conjunction with the designated PPG coatings. Add thinner according to manufacturer instructions to achieve the desired viscosity. Observe safety and application instructions on the container and safety data sheet, and wear personal protective equipment.Technical DataApplication area: Thinning of PPG polyurethane, epoxy, and 1-component coatings; cleaning of toolsCompatible products: SIGMA VIKOTE 18 (Art. 2580-125), SIGMA ECOFLEET 290S (Art. No. 2584-003)Shelf life: At least 60 months when stored in a cool, dry placeFor more information on application, refer to the technical data sheet under 'Downloads'.

Special thinner for Epifanes Poly-Propoxides (PP) 2-component products. Developed to adjust processing viscosity and to clean the tools used after working with these systems.Application: Use only for thinning Epifanes PP-2C products in the quantities specified by the manufacturer. Do not overdose, as this may negatively affect drying and layer formation. Also suitable for cleaning brushes, rollers, and spray equipment after processing PP systems. Observe safety and handling instructions on the container and safety data sheet.Technical DataApplication area: Thinning and cleaning with Epifanes Poly-Propoxides (PP) 2-component productsApplication method: Add to paint or primer mixture according to manufacturer's instructions; clean tools by rinsing

Special cleaner for degreasing polyester and gelcoat surfaces before sanding and painting. EPIFANES Polyester Degreaser removes oil, grease, wax, silicone, and other contaminants that can affect the adhesion of subsequent coatings.Application: Thoroughly wipe the surface with Epifanes Polyester Degreaser. Use a clean, lint-free cloth and change it regularly during use. Apply only to dry surfaces. Observe safety and handling instructions on the container and safety data sheet.Technical DataApplication area: Cleaning and degreasing of polyester and gelcoat surfaces before further treatmentApplication method: Apply with a lint-free cloth and wipe thoroughly

Solvent-based cleaner for cleaning tools and equipment after using Epifanes 1-component varnishes, primers, and paints. Reliably removes fresh varnish and paint residues.Application: Rinse brushes, rollers, or spray equipment with Epifanes cleaning thinner immediately after use. Use only outdoors or in well-ventilated areas. Do not use for thinning varnishes. Observe safety instructions on the container and in the safety data sheet.Important: Not suitable for GRP surfaces; for this purpose, EPIFANES Polyester Degreaser (Art.No. 2059-401) is recommended.Technical DataArea of application: Cleaning of work equipment after processing Epifanes 1-C productsApplication method: Dip or rinse tools in thinner

HEMPEL Thinner No. 808 is suitable for thinning single-component HEMPEL antifoulings and for cleaning tools such as brushes or rollers.

The EPIFANES hardener is suitable for all semi-synthetic single-component varnishes and paints from EPIFANES. Especially in interior areas (e.g. on furniture, work surfaces), where an abrasion-resistant coating system is desired, the hardener can be mixed into the varnish.By adding a maximum of 5 - 7%, the curing time of the varnishes is already significantly reduced without the varnishes losing their essential qualities. By adding up to 50% of the hardener, the varnishes become significantly harder and more abrasion-resistant, but also lose their elasticity.

White Spirit is a turpentine substitute and a mineral oil-based thinner. The product is used to thin paints based on oil and oil-alkyd resin, as well as a cleaning agent for parquet, linoleum, and brushes. It is characterized by consistent quality and good material compatibility.Application: The product is added to the respective paint and mixed. The maximum amount depends on the manufacturer's specifications of the respective paint. In addition, white spirit can be used to clean used painting tools such as brushes. Always close tightly after use and store in a cool, but frost-free place.Technical DataField of application: Thinner for paints based on oil and oil-alkyd resin; cleaning agent Substrate: Painted surfaces, used toolsCoverage: depends on the paint system and desired viscosityDrying times: depends on the paint system usedFurther information on processing can be found in the technical data sheet under 'Downloads'.

Thinner for all Epifanes epoxybased products, like EPIFANES EPOXY PRIMER or EPIFANES INTERIMCOAT. Also suited for soften existing epoxy to allow better bonding for fresh layers.

Color additive for the underwater coating LeFANT T-COAT. Mix the color additive with the primer, then add the hardener and stir thoroughly. One paint pot is sufficient for a 750 ml can.

Type A thinner can be used for many SEAJET products, such as antifoulings and the primer SEAJET Type 015. 5% thinner is usually sufficient as an additive for paint. Can also be used for cleaning painting tools.&nbsp

Orange terpene thinner/solvent.Especially intended for use with BIO PIN varnishes and oils.