- Rigg & sail
- Rope & cordage
- Anchoring & mooring
- Hull & deck
- Cabin & comfort
- Paint & boatbuilding
- Electrics & engine
- Pumps & sanitation
- Safety & VHF radio
- Navigation & books
- Commercial shipping
Carbine hooks
Stainless-steel carabiner, material 1.4401 (AISI316).The joint on the closure is somewhat offset to create a larger opening.With closed eye and Key-Lock System.
Carabiner hook with fixed eye made from seawater-resistant manganese bronze, spring made from stainless steel.Model 1574-555: nickel-plated bronze.Also available with swivel eye (see similar products).
Quality WICHARD snap hook, made from forged stainless steel. With clip springs. and swivel eye.A beautifully polished and rounded form makes these high-strength fittings into "hand-flatterers".
Fire department carabiner hook made from A4 stainless steel with closed eye.The eye can be removed so that the hook can be used without it.
Stainless steel hook with swivel eye and safety latch, also qualified as a hook for the boat trailer.
Carbine hook from stainless steel with round eye, asymetric shape and coulter clip.
Patented stainless steel WICHARD model. The asymmetric shape allows an exceptionally high breaking strength.Very well suited for harness tethers, because these hooks have no sharp edges.The size 1232-170 is well suited for catching mooring balls, due to it's large 30mm opening.The safe working load (WLL) when lifting loads is â…• of the specified breaking load .
Small carabiner with swivel eye made of seawater-resistant manganese bronze or stainless steel.For light loads. Stainless steel spring.Also makes a good keychain.
Cast stainless steel snap-shackles, polished.With safety latch.Inexpensive design.
Simple carabiner hook (fireman's carabiner).Made from galvanized steel.
Snap hook made of forged stainless steel (material 1.4401, V4A) with high strength and guaranteed breaking load. Thanks to the special torsion spring clasp, a WICHARD design, the hook has no sharp edges!The safe working load (WLL) for lifting loads is â…• of the specified breaking load.
Quality WICHARD snap hook, made from forged stainless steel. With clip springs.A beautifully polished and rounded form makes these high-strength fittings into "hand-flatterers". Also available with swivel eye.
High-quality stainless steel (1.4401 V4A) snap hook.Closed eye and patented closure with no catching edges.
High-quality snap hook with screw closure to prevent unexpected openingMade from 1.4401 (V4A) stainless steel.Closed eye and patented closure with no catching edges.
High-quality stainless steel (1.4401 V4A) snap hook, asymmetric shape, for harness tethers.With screw closure to prevent unexpected opening.Closed eye and patented closure with no catching edges.
High-quality stainless steel snap hook, which, with 35 kN carbines, belongs to the strongest, that are approved according to EN 362.04B of the fall protection clause.Especially the large width inside and the wide opening at the muzzle with at the same time compact size make this snap hook ideal for climbing and securing in the rigging. Also this enables the crew to hook to wires or shackles without any problems.Each carbines is tested and certified individually as well as equipped with non catching KEY LOCK and a screw closure to prevent an unexpected opening.A safety ring prevents a unintended release of the climbing harness, but must be ordered separately as an accessory.
Small carabiner with brass or stainless steel swivel eye.Also makes a good keychain.
Small carabiner with brass or stainless steel swivel eye.Also makes a good keychain.
Forged version made from strong, seawater-resistant manganese bronze. Spring-loaded flap made from stainless steel (AISI 316).
Made of 1.4401 stainless steel (AISI 316), with a safety latch and spring also made of stainless steel.
Aluminum carabiner with double gate safety system. To open the carabiner push the rear gate with your palm while pulling the front gate with your fingers. The rear gate is protected in order to prevent accidental opening. The grommet fits for a belt strap up to 20 mm or for rope with a diameter up to 14 mm. Main axis load: 33 kN Minor axis load: 12 kN Open gate load: 15 kN Lenght: 136 mm Width: 70 mm Opening width: 26 mm Weight: 130 g
A snap hook forged from high-strength stainless steel (17.4 PH AISI 630) in a classic design, yet with an exceptionally high breaking load. A high-performance product from the French quality manufacturer WICHARD.
