When choosing a sound signalling device, marine equipment for pleasure boats and yachts offers a wide range of pneumatic and electrical systems. Signal whistle, Bosun's whistle or life jacket whistle are small acoustic aids in on-board and rescue communication. A sought-after classic nautical instrument is the TYFON, formerly used aboard tall ships. It is a large brass pump fog horn operated by a manual pump. The traditional mouth-operated fog horn can still be found on most boats today. For boats using a compressor or compressed air, a compressor horn is suitable. For smaller boats, we offer not only portable air horns, as often used by football fans, but also built-in electro-pneumatic horns with an integrated compressor. These do not require air tubing. Electric horns or unpressurized electric horns with electromagnetic sound generation are frequently found on motorboats. Sometimes they are called boat trumpet horns or truck horns. In traditional shipping and commercial shipping certified electronic sound signalling systems are mandatory. The acoustic signal systems can also be combined with an intercom system for onboard communication. In addition, these ships must be equipped with a certified ship's bell and a signal gong for emitting fog signals.
- Rigg & sail
- Rope & cordage
- Anchoring & mooring
- Hull & deck
- Cabin & comfort
- Paint & boatbuilding
- Electrics & engine
- Pumps & sanitation
- Safety & VHF radio
- Navigation & books
- Commercial shipping
Sound & visual signals
Heavy ship's bell made of polished brass. The bell is manufactured using the traditional sand casting process. It is cleanly turned and polished on the outside and cast-grey on the inside. The surface is unlacquered.Type-tested and approved by the BSH (Federal Maritime and Hydrographic Agency - Bundesamt für Seeschifffahrt und Hydrographie). You will find the National Approval as a pdf file under "Downloads".Equipment regulation according to KVR/COLREG, rule 33a:All ships over 20 m (ship class I, II, III) carry a bell with a diameter of at least 300 mm.Ships under 20 m (ship class IV) are not required to be equipped in accordance with COLREG/COLREG. However, a bell with a diameter of 200 mm is recommended.Delivery includes test certificate for the bell.
BSH approval. Hand-cast brass bell with moulded lettering (e.g. ship's name) in raised letters.Font: Helvetica in capital letters. The letters are approx. 15 mm high and protrude approx. 3 mm. The text is set in such a way that it can be read in full when looking at the bell. You will receive a design proposal for approval. Only then will the bell be cast as an individual item. Delivery time: approx. eight weeks.As the bell cannot be turned in the area of the letters, this strip remains raw in the surface. The rest of the bell body is polished by hand. Irregularities in the lettering are unavoidable with this traditional production method (and therefore no reason for complaint). The clapper is made of grey cast iron.The price for the letters is added to the basic price of the bell according to the bell size and number of letters.When ordering, please specify the exact text you require under ‘Comments’.The bell is type-tested. The DHI certificate can be found under ‘Downloads’. The DHI stamp can be stamped into the spigot on request.Equipment requirement according to KVR/COLREG:All ships over 20 metres in length (ship class I, II, III) must carry a bell with a diameter of at least 300 mm.Ships under 20 metres in length (ship class IV) are not required to be equipped in accordance with KVR/COLREG: We recommend a bell with a diameter of 200 mm.
For large ship's and fog bells. Made from sand-cast brass. Finish either rolled and polished (unvarnished) or chromed. The "A" measurement should be at least 0.6 x the bell's diameter.
Ships bell made from brass with wall bracket. The bell is manufactured in the traditional casting method and has a high gloss finish.The wall bracket is supplied with a mounting wedge: only this piece is screwed on. Thus the bell can simply be dismounted from the wedge and put away.These bells are die-cast from brass and therefore have a clear, high sound. The bell with diameter 300 mm is RINA approved as signal bell of ships over 20 m with carriage requirements. Shipment: bell, bracket, mounting wedge. Available with polished or chromed finish.
Traditional bell rope, also suitable for larger bells in the longer lengths.The rope is cleanly handcrafted from rot-proof, natural-coloured polyhemp cordage.A Turkish knot is woven into the crown plating. With a brass thimble.
Holder for ship's and fog bells. Made from sand-cast brass. Finish either rolled and polished (unlacquered) or chromed.The "A" measurement should be at least 0.6 x the bell's diameter.
Heavy ship's bell with exceptionally canorous sound made from brass. Handmade in Germany, using a traditional sand-casting technique. Every bell is cleanly dressed to size and polished after casting, the top and suspension bracket are left unpolished. The bells are not varnished.
These bells are die-cast from brass, the surface is brass polished or chrome plated. The sound is clear and very bright. They are lighter than sand cast bells.Supplied complete with bell holder and white ribbon.
Straight wall bracket for ship's bells. Made from sand-cast brass. Finish either rolled and polished (unlacquered) or chromed. This straight holder is also well suited for lamps, etc. When used for a bell, the holder measurement "A" should be at least 0.6 x the bell's diameter.
Traditional bell cord made of rot-proof polyhemp rope, natural colour.Neatly handcrafted as a crown plating, with a brass ferrule.
On request, we can engrave all bells with a diameter of 200 mm or more for you. The bell must be ordered separately. The delivery time is approx. 3 weeks.When ordering, please specify the exact text, the desired spelling (in upper/lower case) and the font (many standard PC fonts are possible, font samples can be downloaded under "Downloads" on this page) under "Comments". The engraver determines the letter size depending on the desired text and the size of the bell.The price of the engraving is made up of the basic price (this includes 12 letters) and, if applicable, the surcharge for additional letters according to the number of letters and bell size.
Large gong made of polished brass.Type-tested and approved by the BSH (Federal Maritime and Hydrographic Agency Germany).Equipment regulation according to KVR/COLREG, regulation 33a:All vessels over 100 m carry a gong in addition to the bell (with a diameter of at least 300 mm).The gong is used to give fog signals at anchor. Diameter 500 mm, total weight 4.2 kg.Delivery includes striker and test certificate.
Marco EW3 electronic sound signaling system with pressure chamber loudspeaker.The system is approved for ships < 75 m (IMO Class IV) by RINA, Bureau Veritas, Lloyd's Register and BSH as a sound signaling system ("whistle") in accordance with KVR (COLREG 1972). You will find the relevant certificates at the end of the user manual (see "Downloads").Technical featuresSound frequency 675 HzLoudness 122 dB(A) at 1 mIntegrated ultrasonic preheating of the membrane for improved sound quality at low temperaturesFor 24 VDimensions: see photo 2Weight: 3.8 kglisten to the sound here.OperationThe control panel can be used to start fog signals or individual tone sequences (up to eight tones) with a repetition of 60 or 90 secondsThe horn can be activated as required using a separate push button (not included) - with absolute priority, e.g. before a fog signal that has already been startedScope of deliveryWaterproof (IP67), heatable horn (loudspeaker) with bracket for mounting on the mastA factory-fitted, one meter long, tin-plated power cable with a cross-section of 2 x 1.5 mm² is attached to the acoustic horn. To ensure watertightness, the cable gland is sealed (opening the seal will invalidate the warranty). The required cable length to the control unit must be connected to this cableControl unit with sound generator for below-deck installationControl panel for bulkhead mounting5 meter RJ45 cable for connecting the control panel and control unit. Note: The watertight cable gland in the control unit is unfortunately too small for the plug size of this cable and must therefore be adapted. In the control panel, the plug of the cable ensures that the box cannot be closed again. Therefore, use the control panel for bulkhead mounting.
A replacement part of the electronic horn MARCO EW3 is also the acoustic horn (loudspeaker) for mounting in the mast..Fitting also as bull horn loudspeaker for outside montage.
Horn for use with compressed air.Pleasant deep tone: approx. 315 Hz, volume 123 dB(A) (1 m).For ships up to 20 metres in accordance with the international COLREG 1972 regulations.EU approval for IMO Class IV from RINA, Lloyd's Register, BureauVeritas, MCA, BSH and NMMA.Comes complete with compressor MARCO M1, air tube (5,0 m long, 8mm) and assembly materials.The distance between horn and compressor should not exceed 5,0 m in order to avoid pressure loss.Brass horn, painted white or chromed.Frequency approx. 315 Hz, 123 dB(A) (1m). Listen to the sound here.The matching compressor MARCO M1 is available as a spare part.
Electronic sound signaling system with pressure chamber loudspeaker and microphone for audio announcements. The system has an approval for ships up to 20 m as a signal system and fog horn, according to COLREG 1972, IMO Class III, approved by BSH, RINA, Lloyd's Register, MCA, BureauVeritas.The EW2M sound signaling system consists of the waterproof (IP67) sound horn (loudspeaker) for mounting on the mast, the control box with sound generator (200 x 150 x 80 mm), the control panel and a microphone with talk button.The sound frequency is 675 Hz, the loudness 122 dB(A) at 1 m. A signal of up to 8 tones can be programmed, with a repeat frequency of 60 or 90 seconds.The integrated ultrasonic preheating of the membrane improves the sound quality under cold conditions. Listen to the sound here.Available for an on-board voltage of 12 volt or 24 volt.Operation:either via the supplied control panel, which is connected via an RJ45 cable (also supplied) (length 5.0 m),or via a pressure switch (not included).
Compact M1 compressor from the Italian manufacturer MARCO. This oil-free compressor, with a pressure of 2 bar, is suitable for intermittent operation in audible warning systems.Available in 12 V or 24 V versions.Air flow rate: 60 l/minMotor power: 180 WThreaded connection: BSP 1/8". A hose nipple for an 8x10 mm compressed air line is screwed in as standard. If a 6x8 mm compressed air line is to be used, an additional hose nipple (Part No. 1964-003, see "Accessories & spare parts") is required.Splash-proof: in accordance with IP67
Compact, lightweight, quiet compressor with an 8-liter storage tank.Stays stable thanks to four rubber feet and features a convenient carrying handle on the motor. The compressor is equipped with a pressure gauge and a condensate drain valve.It is suitable for audible warning systems and other compressed air applications on board. According to the manufacturer, however, it is not designed for continuous operation.Technical SpecificationsAvailable for 12 V or 24 V onboard power systemsMotor power: 240 wattsOperating pressure up to 8 barAir delivery: approx. 47 liters of air per minuteConnection: 1/4" screw fitting with hose nozzle and union nut for 8 mm plastic tubing (6 mm inner diameter). You can find this compressed air hose further down on this page under "Accessories & Replacement Parts."
The horn complies with the KVR (COLREG) requirements for audible signaling systems on seagoing vessels less than 75 meters in length. Furthermore, it may be used on inland waterway vessels (< 75 meters) operating on European waterways and German maritime waterways, where the same acoustic signaling regulations apply as for seagoing vessels of the same length.The H400 Maritone compressed-air horn from Den Haan Rotterdam has an audible range of more than one nautical mile.The diaphragm housing is made of 316L stainless steel, and the diaphragm is made of phosphor bronze. The bell is made of brass and painted white (with a red interior). These high-quality materials ensure a long service life.Operation requires an 8x10 mm compressed air line with a connector, a solenoid valve, and a pushbutton or control panel. You can find all of these under “Accessories & spare parts” further down on this page. The connected compressor must deliver an air flow rate of at least 8–12 l/s at a pressure of 7 bar. Technical SpecificationsSound pressure: 130 dB at 1/3 octave or 140 dB(A)Frequency: 440 HzRequired compressed air: 7 barAir consumption: 8 to 12 l/sConnection: ¼" with coupling for plastic hose (⌀ 10 mm).Materials: Stainless steel (1.4401) diaphragm housing and a brass horn with a white (red on the inside) powder coatingApproval: Seagoing vessels and inland waterway vessels on German inland waterways (each < 75 meters in length)
Horn PW2-B for use with compressed air. For ships up to 20 metres in accordance with the international COLREG 1972 regulations.EU approval for IMO Class IV from RINA, Lloyd's Register, BureauVeritas, MCA, BSH and NMMA.Comes complete with compressor MARCO M1, air tube (5,0 m long, 8mm) and assembly materials.The distance between horn and compressor should not exceed 5,0 m in order to avoid pressure loss.Brass horn, painted black or chromed.Frequency approx. 315 Hz, >120 dB(A) (1m). Listen to the sound here.The matching compressor MARCO M1 is available as a spare part.
Compact electro-pneumatic signal horn for installation. The horn with a very loud, amazingly low tone (volume 120 dB(A), frequency 300 Hz) is suitable for ships under 12 m in length or as a secondary system.The powerful compressor is integrated in the housing. This means that no compressed air line is required and installation is very simple.The body and the visible panel are made of plastic, the bracket is made of stainless steel.The cover is available in white (HR1), black (HR1/B) or chrome-plated (HR1/C). Optionally for 12 or 24 volt on-board voltage.The horn is supplied ready for installation with switching relay. A switch is not included in the scope of delivery. NMMA type-tested.DimensionsPanel 185 x 125 mmInstallation depth behind bulkhead 130 mm
Electromagnetic double horn with funnels, bracket and diaphragm made of stainless steel.The design of the bracket ensures that the cable remains hidden.Complete with mounting kit.122dB(A). Frequency 370 / 340 Hz. Weight 1.8 kg. Listen to the sound here.
Unpressurized electric horn with electromagnetic sound generation. Stainless steel horn.Volume 118 dB (A), frequency 370 Hz. Listen to the sound here.
The control panel SB-UV for the electronic horns MARCO EW2 and EW3 has been designed to operate the electronic whistles from the cabin.The installation time of the whistle is reduced thanks to the integrated microprocessor electronic card which transmits through only one RJ45 cable all the available functions to the whistle: horn, fog signal and aux input. The electronic card is contained in a waterproof (IP67) box with built-in option.Can be used for 12 and 24 volt power supply.
Compressed air signal horn with horn of chromed brass.Comes with compressor, relay and assembly materials.Frequency 228 Hz. Volume 108 dB (A). Listen to the sound here.A spare compressor is also available.
MARCO TC1/P small electropneumatic horn (250 x 100 mm) with high sound output. Works with an acoustic pressure of 116 dB(A) and a frequency of 420 Hz. Listen to the sound here.Body made of white ABS plastic.Comes complete with electric compressor, tubing (120 cm) and mounting kit.Available for 12 Volt or 24 Volt.
Compressed-air double hornDeep tone 177 / 218 Hz,105 db(A). Listen to the sound here.Made of chromed brass.Comes with compressor, relay and assembly materials.Available for 12 Volt or 24 Volt systems.
MARCO TCE electromagnetic horn with reduced dimensions but with high sound output. Runs with an acoustic pressure of 114 dB(A) and a frequency of 350 Hz. Listen to the sound here.A robust construction of trumpet - made of white enamel brass - and body - made of stainless steel.Little energy consumption. Available in 12 Volt or 24 Volt.Dimensions L x D: 250 x 100 mm.
Electric horn of all brass construction, with spun body and trumpet.Brass bracket.Surface polished brass or chrome plated.Volume 114 dB(A), frequenzy 340 Hz,.Available for 12V or 24V.
Simple electromagnetic horn made of chrome-plated brass.The electromagnetic sound group is carefully protected, made of anti-corrosive material and the chrome plating is resistant to salt. Complete with mounting bracket.Volume 114 dB(A).Optionally with low tone (bass, MT1-L), frequency 410 Hz, orwith high tone (treble, MT1-H), frequency 490 Hz.Can be used as a single horn.Alternatively, the high-frequency horn and the low-frequency horn can be combined to form a double horn.Available for 12 V or 24 V. Listen to the bass sound here.
MARCO acoustic funnel for operation with compressed air.In accordance with COLREG 1972, IMO Class III approved by RINA, Lloyd's Register, BureauVeritas for ships up to 75 m in length.Sound funnel made of brass, surface painted white.Compressed air supply of 6-12 bar (6 l/sec) is required on board. The electromagnetic control valve is supplied. It must therefore be ordered to match your on-board voltage (12 volt or 24 volt).The scope of delivery also includes: 10 meter plastic compressed air line 6x8 mm and connection material.Frequency 315 Hz, 132 dB(A) (1 m). listen to the sound here.
Marco EW2 electronic sound signaling system with pressure chamber loudspeaker.The system is approved for ships < 20 m (IMO Class IV) by RINA, Bureau Veritas, Lloyd's Register and BSH as a sound signaling system ("whistle") in accordance with KVR (COLREG 1972). You will find the relevant certificates at the end of the user manual (see "Downloads").Technical featuresSound frequency 675 HzLoudness 122 dB(A) at 1 mIntegrated ultrasonic preheating of the membrane for improved sound quality at low temperaturesOptionally for 12 V or 24 VDimensions: see photo 2Weight: 3.8 kg listen to the sound here.OperationThe control panel can be used to start fog signals or individual tone sequences (up to eight tones) with a repetition of 60 or 90 secondsThe horn can be activated as required using a separate push button (not included) - with absolute priority, e.g. before a fog signal that has already been startedScope of deliveryWaterproof (IP67), heatable horn (loudspeaker) with bracket for mounting on the mastA factory-fitted, one meter long, tin-plated power cable with a cross-section of 2 x 1.5 mm² is attached to the acoustic horn. To ensure watertightness, the cable gland is sealed (opening the seal will invalidate the warranty). The required cable length to the control unit must be connected to this cableControl unit with sound generator for below-deck installationControl panel for bulkhead mounting5 meter RJ45 cable for connecting the control panel and control unit. Note: The watertight cable gland in the control unit is unfortunately too small for the plug size of this cable and must therefore be adapted. In the control panel, the plug of the cable ensures that the box cannot be closed again. Therefore, use the control panel for bulkhead mounting.
Megaphone with plastic housing and a hand / switch handle with wrist strap. Specifications:Output power max. 15 W, average sound pressure 100 dB, -Piezo technology, built-in microphone, siren and beeper switchable,volume control.Length: 340 mm.Funnel diameter: 205 mm.Weight: approx. 1.1 kg.Operation with standard batteries (8x1.5 Volt Mignon batteries). Delivery without batteries.
The open loudhailer, nowadays usually referred to as a megaphone concentrates the sound and directs it specifically in one direction so that the intelligibility of spoken language in particular is improved even over greater distances. The speaker places the smaller of the two openings in front of the mouth, while turning the larger one toward the listeners. Well suited, for example, for training rowers or sailors. The TOPLICHT megaphone is made of polished sheet brass.
Mouthpiece for setting up an "analog" intercom system, as was traditionally used on commercial vessels.Two mouthpieces are connected to a suitable hose or pipe.The classically shaped mouthpiece is made of polished brass and the matching pipe is secured with a brass chain.The pipe socket has a diameter of 30 mm and a 1" Withworth internal pipe thread.
200-ml pressurized gas cylinder as a replacement for the MARCO TA1-H compressed-air handheld signal horn, which the manufacturer no longer offers.The replacement cylinder is filled with non-flammable propellant (tetrafluoropropene HFO-1234ze, compliant with European Directive No. 517/2014). It is sufficient for approximately 200 signals, each lasting 2 seconds.
Curved mouth-operated fog horn of high-quality design, made by the traditional german manufacturer MARTIN.Entirely made from polished brass.With brass reed that produces a very intense sound.Brass mouthpipe with plasic cover (may be removed).Tuned to C'.
Plastic signal horn with stainless steel membran, pressurised gas operated. Very loud penetrating sound approx. 122 dB(A), frequency 400 Hz.Supplied complete with compressed gas cylinder (750 ml capacity) in a practical storage bag. Non-flammable propellant gas tetrafluoropropene HFO-1234ze, complies with European Directive No.517 / 2014).Sufficient for approx. 750 signals of 2 seconds each.The 200ml gas cylinder (article no. 3403-100) can be used as a replacement cylinder. You will find these further down on this page under "Accessories".
Straight mouth-operated fog horn, entirely made from brass.Pr oduced by the german manufacturer MARTIN, of high-quality design.Brass mouthpiece and reed that can be unscrewed, re-tuned and replaced, if necessary.Very loud and intense sound.Replacement brass reed and mouthpipe are available and make this horn a fine example for sustainable, long lasting quality products.Tuned to F sharp'.
Straight plate-brass fog horn, cleanly grooved. Polished finish.Mouth piece with solid metal reed.
Spares reed for fog horn MARTIN (Art-Nr. 3417-410): - spare brass reed (tuned fis'), screws into the horn, - spare brass mouthpipe.
Polished brass foghorn. Handy, curved design with a brass chain.
The Mini-TRUMP generates a very loud signal! Up to 100 dB(A) are possible by simply blowing this horn.A piece of safety gear, because it gives a good signal without an external energy source.Made from yellow plastic.The tone comes from blowing in a hole on the side.
Functional plastic fog horn. Light and corrosion-proof.Body and reed of red plastic.
Mouthpiece for setting up an "analog" intercom system, as was traditionally used on commercial vessels.Two mouthpieces are connected to a suitable hose or pipe.The classically shaped mouthpiece is made of polished brass and the matching pipe is secured with a brass chain.The pipe socket has a diameter of 30 mm and a 1" Withworth internal pipe thread.
This item is unfortunately no longer available.Reproduction of the Swedish "TYFONS" as used on board tall ships in the past.With a beautifully crafted heavy brass cylinder and funnel on a varnished mahogany base plate, this horn is not only a safety-relevant (reserve) piece of equipment for larger ships, but also a piece of maritime jewelry.The loud and deep signal tone is produced when pumping up and down, so a continuous tone can also be produced by pumping faster. The brass tuning diaphragm is adjustable.
The pump foghorn used in commercial shipping produces a deep, penetrating continuous tone.It is made entirely of brass by Den Haan Rotterdam (DHR). The pump piston has a leather membrane.The bell is firmly soldered to the pump piston.With leather carrying strap.MeasurementsTotal height: 550 mmWeight: 1.5 kgPump cylinder: 100 mm diameter, 500 mm height
Handy air horn, works WITHOUT GAS. Air pressure is generated manually, for maximum economy and sound performance. Pump housing and trumpet made of plastik.
Plastic compressed-air signal horn with a stainless-steel diaphragm, pressurized-gas operated.Very loud, piercing sound with a range of approximately 1,500 meters.Comes complete with a compressed gas cylinder (flammable propane-butane mixture) with a capacity of 380 ml.The 380-ml pressurized gas cylinder is also available as a replacement part.UsageAttach the signal horn by screwing it onto the gas cartridgeTo activate, press the signal horn downwardThe signal horn must only be used in an upright positionDo not store the pressurized gas cylinder in direct sunlight, and do not expose it to temperatures above 40 °C
Historically the boatswain's call was used to pass commands to the crew when the voice could not be heard over the sounds of the sea.The pipe consists of a narrow tube (the gun) which directs air over a metal sphere (the buoy) with a hole in the top. The player opens and closes the hand over the hole to change the pitch. Available with polished or nickel-plated surface. Instructions for using the whistle are included.The brass whistle is delivered with a chain. The nickel-plated version is delivered without a chain.
Loud signalling whistle made from nickel plated brass with ring.
Mouthpiece for setting up an "analog" intercom system, as was traditionally used on commercial vessels.Two mouthpieces are connected to a suitable hose or pipe.The classically shaped mouthpiece is made of polished brass and the matching pipe is secured with a brass chain.The pipe socket has a diameter of 30 mm and a 1" Withworth internal pipe thread.
Daytime signal in accordance with the International Regulations for Preventing Collisions at Sea (COLREGs) and the German Inland Waterways Regulations, Binnenschifffahrtsstraßen-Ordnung (BinSchStrO).Brand quality from the Dutch manufacturer Den Haan Rotterdam (DHR), which fulfils the requirements of commercial shipping.The anchor ball / signal ball can be folded or collapsed and can therefore be stowed away to save space. Attachment to two swivel mountings or spliced-in fastening hooks.The 6 mm thick, galvanised steel rings are covered with heavy, stitched PVC mesh fabric that offers little wind resistance.Diameter: 600 mmColour: black
Daytime signal in accordance with the International Regulations for Preventing Collisions at Sea (COLREGs) and the German Inland Waterways Regulations, Binnenschifffahrtsstraßen-Ordnung (BinSchStrO).Lightweight, simple imported version for occasional use only.The anchor ball / signal ball is collapsible or foldable and has two suspension hooks.The 5 mm thick steel rings are painted black and sewn with fabric.Diameter: 600 mmColour: black
Daytime signal in accordance with the International Regulations for Preventing Collisions at Sea (COLREGs) and the German Inland Waterways Regulations, Binnenschifffahrtsstraßen-Ordnung (BinSchStrO).Brand quality from the Dutch manufacturer Den Haan Rotterdam (DHR), which fulfils the requirements of commercial shipping.The signal cone can be folded or collapsed and can therefore be stowed away to save space. Attachment to two swivel mountings or spliced-in fastening hooks.The 6 mm thick, galvanised steel rings are covered with heavy, stitched PVC mesh fabric that offers little wind resistance.Measurements: 600 x 600 mmColour: blue
Anchor ball / signal ball made of black plastic, can be plugged together.For vessels under 20 metres in length.Available in yacht size or cutter size.
Motor cone / signalling cone made of black plastic, can be plugged together.In yacht size. For vehicles under 20 metres in length.
Daytime signal in accordance with the International Regulations for Preventing Collisions at Sea (COLREGs) and the German Inland Waterways Regulations, Binnenschifffahrtsstraßen-Ordnung (BinSchStrO).Lightweight, simple imported version for occasional use only.The motor cone / signal cone is collapsible or foldable and has two suspension hooks.The 5 mm thick steel rings are painted black and sewn with fabric.Measurements: 600 x 600 mmColour: black
Daytime signal in accordance with the regulations of the Collision Prevention Regulations (COLREGs) and the Inland Waterways Regulations, Binnenschifffahrtsstraßen-Ordnung (BinSchStrO).Lightweight, simple imported version for occasional use only.The signalling cylinder can be folded or collapsed and has two suspension hooks.The 5 mm thick steel rings are painted black and sewn with fabric.Dimensions: 600 x 1200 mmColour: black
Daytime signal in accordance with the regulations of the Collision Prevention Regulations (COLREGs) and the Inland Waterways Regulations, Binnenschifffahrtsstraßen-Ordnung (BinSchStrO).Lightweight, simple imported version for occasional use only.The signalling rhombus can be folded or collapsed and has two suspension hooks.The 5 mm thick steel rings are painted black and sewn with fabric.Dimensions: 600 x 1200 mmColour: black
Daytime signal in accordance with the regulations of the Collision Prevention Regulations (COLREGs) and the Inland Waterways Regulations, Binnenschifffahrtsstraßen-Ordnung (BinSchStrO).Lightweight, simple imported version for occasional use only.The signalling hourglas can be folded or collapsed and has two suspension hooks.The 5 mm thick steel rings are painted black and sewn with fabric.Dimensions: 600 x 1200 mmColour: black
Daytime signal in accordance with the International Regulations for Preventing Collisions at Sea (COLREGs) and the German Inland Waterways Regulations, Binnenschifffahrtsstraßen-Ordnung (BinSchStrO).Brand quality from the Dutch manufacturer Den Haan Rotterdam (DHR), which fulfils the requirements of commercial shipping.The signal cone can be folded or collapsed and can therefore be stowed away to save space. Attachment to two swivel mountings or spliced-in fastening hooks.The 6 mm thick, galvanised steel rings are covered with heavy, stitched PVC mesh fabric that offers little wind resistance.Measurements: 600 x 600 mmColour: black
Daytime signal in accordance with the International Regulations for Preventing Collisions at Sea (COLREGs) and the German Inland Waterways Regulations, Binnenschifffahrtsstraßen-Ordnung (BinSchStrO).Brand quality from the Dutch manufacturer Den Haan Rotterdam (DHR), which fulfils the requirements of commercial shipping.The signal cylinder can be folded or collapsed and can therefore be stowed away to save space. Attachment to two swivel mountings or spliced-in fastening hooks.The 6 mm thick, galvanised steel rings are covered with heavy, stitched PVC mesh fabric that offers little wind resistance.Measurements: 600 x 1200 mmColour: black
Daytime signal in accordance with the International Regulations for Preventing Collisions at Sea (COLREGs) and the German Inland Waterways Regulations, Binnenschifffahrtsstraßen-Ordnung (BinSchStrO).Brand quality from the Dutch manufacturer Den Haan Rotterdam (DHR), which fulfils the requirements of commercial shipping.The signal rhombus can be folded or collapsed and can therefore be stowed away to save space. Attachment to two swivel mountings or spliced-in fastening hooks.The 6 mm thick, galvanised steel rings are covered with heavy, stitched PVC mesh fabric that offers little wind resistance.Measurements: 600 x 1200 mmColour: black
Daytime signal in accordance with the International Regulations for Preventing Collisions at Sea (COLREGs) and the German Inland Waterways Regulations, Binnenschifffahrtsstraßen-Ordnung (BinSchStrO).Brand quality from the Dutch manufacturer Den Haan Rotterdam (DHR), which fulfils the requirements of commercial shipping.The signal ball can be folded or collapsed and can therefore be stowed away to save space. Attachment to two swivel mountings or spliced-in fastening hooks.The 6 mm thick, galvanised steel rings are covered with heavy, stitched PVC mesh fabric that offers little wind resistance.Diameter: 600 mmColour: red
Daytime signal in accordance with the International Regulations for Preventing Collisions at Sea (COLREGs) and the German Inland Waterways Regulations, Binnenschifffahrtsstraßen-Ordnung (BinSchStrO).Brand quality from the Dutch manufacturer Den Haan Rotterdam (DHR), which fulfils the requirements of commercial shipping.The signal ball can be folded or collapsed and can therefore be stowed away to save space. Attachment to two swivel mountings or spliced-in fastening hooks.The 6 mm thick, galvanised steel rings are covered with heavy, stitched PVC mesh fabric that offers little wind resistance.Diameter: 600 mmColour: yellow
Daytime signal in accordance with the International Regulations for Preventing Collisions at Sea (COLREGs) and the German Inland Waterways Regulations, Binnenschifffahrtsstraßen-Ordnung (BinSchStrO).Brand quality from the Dutch manufacturer Den Haan Rotterdam (DHR), which fulfils the requirements of commercial shipping.The signal cylinder can be folded or collapsed and can therefore be stowed away to save space. Attachment to two swivel mountings or spliced-in fastening hooks.The 6 mm thick, galvanised steel rings are covered with heavy, stitched PVC mesh fabric that offers little wind resistance.Measurements: 500 x 800 mmColour: white-black-yellow-black-white
Daytime signal in accordance with the International Regulations for Preventing Collisions at Sea (COLREGs) and the German Inland Waterways Regulations, Binnenschifffahrtsstraßen-Ordnung (BinSchStrO).Brand quality from the Dutch manufacturer Den Haan Rotterdam (DHR), which fulfils the requirements of commercial shipping.The signal rhombus can be folded or collapsed and can therefore be stowed away to save space. Attachment to two swivel mountings or spliced-in fastening hooks.The 6 mm thick, galvanised steel rings are covered with heavy, stitched PVC mesh fabric that offers little wind resistance.Measurements: 500 x 800 mmColour: black
Daytime signal in accordance with the International Regulations for Preventing Collisions at Sea (COLREGs) and the German Inland Waterways Regulations, Binnenschifffahrtsstraßen-Ordnung (BinSchStrO).Brand quality from the Dutch manufacturer Den Haan Rotterdam (DHR), which fulfils the requirements of commercial shipping.The signal cylinder can be folded or collapsed and can therefore be stowed away to save space. Attachment to two swivel mountings or spliced-in fastening hooks.The 6 mm thick, galvanised steel rings are covered with heavy, stitched PVC mesh fabric that offers little wind resistance.Measurements: 600 x 1200 mmColour: redSignal for system requiring protection: Avoid suction and wave impact.
Daytime signal in accordance with the International Regulations for Preventing Collisions at Sea (COLREGs) and the German Inland Waterways Regulations, Binnenschifffahrtsstraßen-Ordnung (BinSchStrO).Brand quality from the Dutch manufacturer Den Haan Rotterdam (DHR), which fulfils the requirements of commercial shipping.The signal rhombus can be folded or collapsed and can therefore be stowed away to save space. Attachment to two swivel mountings or spliced-in fastening hooks.The 6 mm thick, galvanised steel rings are covered with heavy, stitched PVC mesh fabric that offers little wind resistance.Measurements: 500 x 800 mmColour: green
Daytime signal in accordance with the International Regulations for Preventing Collisions at Sea (COLREGs) and the German Inland Waterways Regulations, Binnenschifffahrtsstraßen-Ordnung (BinSchStrO).Brand quality from the Dutch manufacturer Den Haan Rotterdam (DHR), which fulfils the requirements of commercial shipping.The signal cylinder can be folded or collapsed and can therefore be stowed away to save space. Attachment to two swivel mountings or spliced-in fastening hooks.The 6 mm thick, galvanised steel rings are covered with heavy, stitched PVC mesh fabric that offers little wind resistance.Measurements: 500 x 1000 mmColour: red-white-red
Daytime signal in accordance with the International Regulations for Preventing Collisions at Sea (COLREGs) and the German Inland Waterways Regulations, Binnenschifffahrtsstraßen-Ordnung (BinSchStrO).Brand quality from the Dutch manufacturer Den Haan Rotterdam (DHR), which fulfils the requirements of commercial shipping.The signal rhombus can be folded or collapsed and can therefore be stowed away to save space. Attachment to two swivel mountings or spliced-in fastening hooks.The 6 mm thick, galvanised steel rings are covered with heavy, stitched PVC mesh fabric that offers little wind resistance.Measurements: 500 x 800 mmColour: yellow
