- Rigg & sail
- Rope & cordage
- Anchoring & mooring
- Hull & deck
-
Cabin & comfort
- Lamps, lights & lanterns
- Clocks, barometers & instruments
- Stoves & heaters
- Cooker, oven & barbecue
- Interior fittings
- Cabinet fittings
- Hinges & strap hinges
- Flush handles
- Locks
- Bolts & fasteners
- Hooks
- Clothing
- Life on board
- Store nets & bags
- Bags & duffel bags
- Cushions & mattress
- Maritime decoration
- Key rings
- Paint & boatbuilding
- Electrics & engine
- Pumps & sanitation
- Safety & VHF radio
- Navigation & books
- Commercial shipping
Heavy door & hatch fasteners
Heavy-duty dog assembly for ship’s doors and hatch covers; the designs comply with DIN 83104. Intended for installation by welding the tube in place.The handles are made of A4 stainless steel and are available in either an raw or polished finish. Depending on the variant, the 73 mm long weld-in tube is made of steel, aluminium or A4 stainless steel. Steel tubes always have (2) brass bearing bushes, whilst the aluminium ans stainless steel tubes are supplied as standard with (2) polyamide bearing bushes.The sleeves have an M10 × 1 thread for fitting a grease nipple.Available designs:Type A: Operation from both sides via two handles.Type B: One handle and a 19 × 19 mm square spigot on the opposite side.Type C: One handle and a flat head on the opposite side.A limit stopper for welding to the door or hatch frame is available separately. You can find spare or single parts under ‘Accessories’.
Heavy-duty dog assembly for ship doors and hatch covers. The design complies with DIN 83104. The forged steel handles (St 37-2) are coated with a reddish-brown zinc oxide primer. Depending on the model, the weld-in tubes are made of steel with (2) brass bearing bushes or aluminum with (2) polyamid bearing bushes. The tubes are equipped with brass bearing bushings and an M10 × 1 thread for a grease nipple.Available designs:Type A: Operation from both sides with two handles.Type B: One handle and a square spigot (19 × 19 mm) on the opposite side.Type C: One handle and a flat head on the opposite side.The closures are available in various versions with 60, 73, or 93 mm long weld-in tubes. The model designation consists of the design (A, B, or C) and the tube length in millimeters; for example, A73 for Design A with a 73-mm-long sleeve.A limit stopper for welding to the door or hatch frame is available separately under “Accessories.” Additional parts can be found in the “Accessories”category .
Heavy hatch made from brass with a firm, strong handle. For bolting bulkheads and doors.With counter plate and bore for a padlock.Surface polished or chromed brass. Suitable for wood, but can also be used for steel bulkheads. Measurements:Hinge length (door depth): 55 mm.Mounting plate for the hinge diameter: 50 mm.Hinge rod diameter = 19 mm.
Strong door fastener for heavy ship doors made from A2 stainless steel.It requires a door thickness of 55-60 mm width, the axis length is not alterable (axis diameter = 15 mm).The handle length is 190 mm, length of the latch is 60 mm. It is on both sides equipped with square mounting plates of (L x W x H) 63 x 63 x 3 mm with 4 countersink holes of 6 mm.The latch has a stop, that restricts the angle of movement to 90°.
Accessories for DIN83104 sash fasteners:Stop pins made of steel or A4 stainless steel for welding.Dimension: 12 x 50 mm (diameter x length)Lubrication nipple made of galvanized steel (M10 x 1) or A4 stainless steel (flat nipple M10 x 1)Form A73 sleeves in various materials for DIN83104 sash fasteners.
Square-ending socket spanner 19 mm made from special stainless steel.Shaft and tommy bar tempered and bronzed for hatch lock.
Large aluminum latch for hatches. Low installation height above deck so that no lines can get caught and there is no risk of tripping.The latch is inserted into the hatch cover in a 50 mm hole with two flattened sides. A large, smooth-running locking lever is located below deck, which engages in a plastic bearing supplied with the hatch by means of a rotary movement and, thanks to its special design, pulls the hatch cover downwards and closes it tightly. The hatch can also be opened again from the inside using the handle.The lock can be operated from the outside using a winch crank with an internationally standardized octagon.The sash lock can be used on hatch covers with a material thickness of up to 25 mm. The cover is fixed with a grub screw on the flattened side of the thread. The threaded rod for holding the handle can be shortened if necessary.
