Further accessories and spare parts can be found directly with the respective pumps.
- Rigg & sail
- Rope & cordage
- Anchoring & mooring
- Hull & deck
- Cabin & comfort
- Paint & boatbuilding
- Electrics & engine
- Pumps & sanitation
- Safety & VHF radio
- Navigation & books
- Commercial shipping
Spare parts & accessories for pumps
Repair kit #0350095 for the RHEINSTROM diaphragm pump M50 and M50E.The set consists of the pump membrane, a large seal and three valve flaps made from plastic.
The MARPOL Convention prohibits the discharge of oily wastewater into the sea. This filter removes the oily substances from the pumped bilge water by a patented filter system, so that the bilge water can be pumped out almost without oil residues and the water pollution is minimized.The filter is installed behind the bilge pump and in front of the ship's passage. It is suitable for oil residues, large dirt must be removed from the bilge before.Supplied with a stainless steel wall mounting plate.Replacement filter cartridges are available, annual replacement is recommended.LLOYD'S REGISTER Type Approved.
An exceptionally practical tool for removing impellers without damaging the pump housing.Body and jaws of aluminum, shaft of stainless steel.Dimensions, approx. 140 x 165 mm (W x H). Weight, 450 g.
Original JABSCO impeller for installation on most cooling water bilge pumps and universal pumps.To keep motors and pumps running smoothly, choosing the right impeller is critical. In addition to the hub mount and size, the material of the impeller should match its application:Neoprene is the most commonly used material for impellers and is suitable wherever only small amounts of oil or diesel fuel are present. Neoprene impellers are therefore suitable for engine cooling and for salt or fresh water pumping.Nitrile is oil resistant and can also be used for heavily polluted water. Impellers made of nitrile are therefore suitable for bilge and bilge pumps.The impellers are usually supplied with a matching paper cover gasket.Other JABSCO impellers and spare parts are also available at short notice on request.To see the matching image for the impeller, simply click on the part number in the table below.
We deliver a lot of spare parts for the WHALE GUSHER 10 bilge pump.
Accessory for bilge water filter WAVESTREAM.
We deliver a lot of spare parts for the WHALE GUSHER TITAN bilge pump.
Contents of service kit AK1550:MembraneValve flapVentMounting screws.Clampingring - kit AS1562 consists of clamping ring and screws.The service kit "pump head" (AK2050) holds the spare parts for the pump head (please check "Downloads & Information").
Deckring without lid for WHALE-pump MK5 (BP0535) for deck- or bulkhead mounting.Manufactured from white, UV-stabilised plastic.
We deliver a lot of spareparts for the WHALE GUSHER URCHIN bilge pump.
Accessories for foot pump WHALE GUSHER MKIII.
Replacement filter AK1319 for WHALE pressure water pumps of the WATERMASTER and UNIVERSAL types. For 15 mm WHALE QUICK CONNECT system.Technical featuresDesign: coarse filterConnection: 15 mm Quick ConnectCover: transparent cover for visual inspection; cover can be removed for cleaningWHALE No.: AK1319For UNIVERSAL models: UF0812, UF0815, UF1212, UF1214, UF1215, UF1225, UF1815, UF1825, UF2014, UF2015, UF8015, UF8025For WATERMASTER models: FW0814, FW0814B, FW1214, FW1214B, FW1215, FW1215B, FW1225, FW1225B, FT0814, FT0814B, FT1214, FT1214B
The Italian FINNORD group produces impellers in OEM quality for different manufacturers of pumps and offers a wide assortment of replacement impellers under the name CEF at reasonable prices.Here we present a selection of popular impellers made from neoprene and nitrile rubber.Usualy shipping complete with matching paper cover gaskets. To see the matching image for the impeller, simply click on the part number in the table below.Other sizes are available.
Spare parts kit (seals) for the CLASSIC galley pump (item no. 4613-014/-514).The CLASSIC spare parts kit (4613-100) is supplied with a nitrile seal only, as it has been found that if the pump is not used regularly, the pump leather can stick to the pump body due to drying out.Older pumps (built before 2011) also require the conversion kit (4613-101), which consists of a screw-on brass pump base valve and a threaded washer.
Plastic hose nozzle with union nut for 1/2" thread with 13 mm hose connection. For SHURFLO AQUAKING Pumpen.Available in straight or angled form.
Impeller of special nitril rubber. Original spare part for UP1, UP1-M and UP1/AC MARCO Pumps.Dimensions hight x Ø: 22 x 51.5 mm.Bore Ø: 8 mm.
Accessory for PLASTIMO bilge pump art-no. 1768-038 and 1768-039.
Accessory for JABSCO impellers: JABSCO impeller grease, 2,5 ml tube.
Spares for FYNSPRAY galley pump WELLINGTON.Please check if your older pump has got a piston seal of leather or a newer pump one of rubber!
Service kit for WHALE/HENDERSON deckplates suitable for underdeck models Gusher 30 and 10, Titan, Urchin, Mk5The kit includes a gaiter (diameter 108mm) and an O-ring.
Outlet elbows for the diaphragm pump PLASTIMO model 11722.They are screwed and fitted with an O-ring for perfect water tightness and added safety (quick release facility). For a tube diameter of 38mm.
Accessory for PLASTIMO bilge pump type 12760 (our Art-No. 1768-025).
