If you like to upgrade the interior of your boat, you should go into detail. Carefully selected, beautiful interior fittings from our range are both suitable and practical. Among these items are for example practical and decorative fiddles, curtain tube stanchions or handrails made of brass or brass tube. Visually appealing rectangular, round or square vent plates and locking hits are quite important below deck. They provide fresh air and help to prevent mould growth inside of cockpit lockers, storage lockers and cupboards. To increase the slip resistance on a staircase or companionway, ribbed brass stair nosings can be attached to the steps. The same function is provided by nonslip step plates with polished or chromed brass frames and rubber inlays, as they are often used on modern sailing yachts.
- Rigg & sail
- Rope & cordage
- Anchoring & mooring
- Hull & deck
-
Cabin & comfort
- Lamps, lights & lanterns
- Clocks, barometers & instruments
- Stoves & heaters
- Cooker, oven & barbecue
- Interior fittings
- Cabinet fittings
- Hinges & strap hinges
- Flush handles
- Locks
- Bolts & fasteners
- Hooks
- Clothing
- Life on board
- Store nets & bags
- Bags & duffel bags
- Cushions & mattress
- Maritime decoration
- Key rings
- Paint & boatbuilding
- Electrics & engine
- Pumps & sanitation
- Safety & VHF radio
- Navigation & books
- Commercial shipping
Interior fittings
Made of polished brass. Simple design with oval base plate.Available as a middle or end post for 20 mm tubing.
Polished or chromed brass rope holders for 20 mm, 30 mm or 40 mm rope railing. All rope holders are delivered with screws to fix the rope. The matching set also includes available floor supports for complete barriers.
Made of polished or chromed brass, with round base plate. Heavy design for spars 25, 30 oder 35 mm.
Polished or chromed brass end pieces for 20 mm, 30 mm or 40 mm rope railing. All end caps are delivered with screws to fix the rope. The matching set also includes available floor supports for complete barriers.
Made of polished or chromed brass, with round base plate. Light design with low overall height, for 25 mm tubing.
Elegant, streamlined hand rail holders made from machine casting for tubing. These rail holders are also useful as companionway handles. The end pieces are equipped with a M6 blind hole, the threaded fittings and nuts are included.
Simple, inexpensive brass fitting for 20 mm pipe.Available as end or middle piece, surface polished or chrome plated.
Wall hook with round base plate. Also suitable for holding a handrail rope, e.g. for a temporary safety rope below deck.Made of brass. With two screw holes. Heavy-duty design from German production. Brass or nickel-plated finish.
Stylish hand rail holder, made from polished brass. Raked by 30°.Fits for 22 mm tube. Also available in chromed brass.
Solid design made of brass, surface polished or chromed. These cylindrical pieces have a central M8 blind hole in the bottom for attachment. Come in a variety of diameters.
Strong fitting of polished cast brass, onto which the wood piece can be attached.With a curved mounting plate for round wood (D = 42 mm) or with a straight plate.
Polished or chromed brass rope holders for 30 mm or 40 mm rope railing. All rope holders are delivered with screws to fix the rope. The matching set also includes available floor supports for complete barriers.
Wall hook with screw and round ground plate.Made from brass. Surface brass polished or chromed.
Wall hook for handrail rope. With rectangular ground plate. Made from brass, surface polished or chrome plated.
Rope post.With two hooks for the rope.Made from brass. Surface brass polished or chrome plated. Hight = 890 mm, tube diameter = 28 mm, base diameter = 260 mm.
Cleanly drawn brass tube with polished surface.Can be used as curtain rod or as a delicate rail.This item is sold in several length.
This natural-fiber rope is woven in the traditional mode, from finely combed hemp threads. The laid 4-strand weave makes for hand rails with good grip. Quality: long hemp, polished, untarred. Exactly fits our hand rail supports.Also suitable as a climbing rope for gyms, loft beds, etc. (not for mountain sports).However, this untreated material should only be used inside.
Brass tubing for a practical and decorative guard rail for the cabin table or for a shelf. This item is sold in several length
Strong and relatively soft rope intended to wrap fenders for ships or dinghies.Laid rope made of waterproof, hemp-colored polypropylene PP- staple fibres (SPLEITEX).Shipping in bulk, whole metres. Available as 220 m coil also.
This natural-fiber rope is woven in the traditional mode, from finely combed hemp threads. The laid 4-strand weave makes for hand rails with good grip. Quality: long hemp, polished, untarred. Exactly fits our hand rail supports.Also suitable as a climbing rope for gyms, loft beds, etc. (not for mountain sports).However, this untreated material should only be used inside.
Polished brass pipe (CuZn37).This item is sold in several lenght.
Stainless-steel pipe A2 polished 1.4301 (AISI 304).This item is sold in several lenghts.
Beautiful, pleasant to grip, solid handle made of heavy, polished brass. Good for placing in the companionway or other places where a firm grip is required.
Solid design of polished cast brass.Slim design with transversally placed feet.
Heavy cast-brass handle/hand-hold. Appropriate for a variety of inside and outside uses. Attached from below, using two M5-thread drilled blind holes. Polished or chromed finish.
Sturdy handle with angled base plate made of heavy polished brass. Well suited for vertical mounting in the companionway, or elsewhere where a safe grip is required.
Slightly asymmetrical handle of cast brass.Polished finish, chromed or matte chromed.
Delicate and shapely handle made of brass.The surface and fittings are polished, mounting takes place from the below. Height of the upper edge: 30 mm. The diameter of the tube is 10 mm.
Strong, solid grab handle made from polished or chromed brass.The handle is mounted from the back by means of two M4 blind hole bores.Weight: 107 g.
Elegant drawer handle made from polished or chromed brass.The handle is mounted from the back by means of two M4 blind hole bores.Weight: 58 g.
Attractive, solid heavy brass handle.Available in polished or chromed brass.Aesthetically simple and functional.
Solid design of polished cast brass.Slim form with longitudinally oriented feet.
Cleanly drawn brass tube with polished surface.Can be used as curtain rod or as a delicate rail.This item is sold in several length.
This system offers the potential to construct a practical and decorative fiddle for the cabin table or for a shelf.All parts are made from brass, very neatly lathed and polished. The supports are available as through, corner, or end supports, at the base with M5 blind thread.The finished guard rail with an diameter of 8 mm has a height of 38 mm.
Brass tubing for a practical and decorative guard rail for the cabin table or for a shelf. This item is sold in several length
Elegant, short centre bracket made of solid brass with cast-in stud bolt (length 20 mm) made of stainless steel. Versatile use, e.g. as a pipe or rod holder or shelf rail center post.The mounting hole has a diameter of 14 mm.Available in brass or nickel-plated brass.Made in Germany.
These delicate and attractive brass end and middle fittings, when combined with a 10 mm brass tube, make an attractive table railing to specified dimensions.The surfaces of the fittings are polished; mounting takes place from the below.Height of the upper edge: 30 mm.The matching 10 mm brass tubing can be ordered under "suitable items" below.
Traditional fiddle fitting for the insertion of 12mm wood ledges. During swell, they are attached around the table to keep objects from falling off. Cast brass, polished finish. Weight: 35 g.
Made of polished brass. Simple design with oval base plate.Available as a middle or end post for 20 mm tubing.
Fittings made of polished brass, suitable for e.g. curtain tubes with a diameter of 10 mm. A central support with galvanized hanger bolt or an end knob are available.
Made of polished or chromed brass, with round base plate. Light design with low overall height, for 25 mm tubing.
Middle stanchion for 12mm curtain rod, made from polished brass.The rod as well as the end piece must be ordered separately.
Solid design made of brass, surface polished or chromed. These cylindrical pieces have a central M8 blind hole in the bottom for attachment. Come in a variety of diameters.
Robust tread of extruded brass, very wear resistant and grippy. Leading edge cleanly rounded. Undrilled. Dimensions 3 x 29 mm, weight 550 g/m.This item is sold in several lengths.
Polished or chromed brass frame, with nonslip, white-rubber insert.Rectangular design.Spare rubber pieces (white or black) are available.
Trapezoidal step plates for companionways or bathing ladders. The frame is made of brass. The white rubber pad prevents slipping on a step.
We offer 6-piece fittings sets for the installation of sliding doors with a four cornered shaft of 8 mm and with 2 m long tracks. The set is made up of:Distinctive hanging tracks (top) with two hanging rollers with fittings and a floor track (below) with two rollers, which can be installed on the bottom of the door. Light design for doors up to 30 kg. Top: Open box section 15 x 45 mm of stainless steel (1.8 kg). Stainless-steel fitting 60 x 70 mm with plastic rollers diameter = 40 mm. Bottom: L-tracks 11 x 12 mm of stainless steel (0.9 kg) with rollers diameter = 17 mm and chromed brass roller fittings 15 x 39 mm.
We offer 6-piece fittings sets for the installation of sliding doors with a four cornered shaft of 8 mm and with 2 m long tracks. The set is made up of: Distinctive hanging tracks (top) with two hanging rollers with fittings and a floor track (below) with two rollers, which can be installed on the bottom of the door. Heavy design for doors up to 150 kg. Top: Open box section 30 x 80 mm of hot-dip galvanized steel (4.5 kg) with brass rollers Diameter = 65 mm, ball bearings, and brass fittings (1 kg) 50 x 155 mm. Bottom: T-tracks 12 x 30 mm of stainless steel (2 kg) with rollers diameter = 30 mm and roller fittings 37 x 64 mm (1,0 kg), chromed brass.
