On a ship, you will find pumps for the most diverse applications. Outside of sailing yachts, the pumps are not visible. On traditional ships, a deck-wash pump or a semi-rotary pump may come into view, but most pumping systems for on-board operation are installed below deck. For water supply, many boats have fresh water pumps, pressure water pumps, wastewater pumps and macerator pumps connected. Due to their beautiful design and simple mechanics self-priming, nostalgic water pumps or marine galley lever pumps are very attractive for on-board use. The robust lever-operated faucet pumps made of solid or chrome-plated brass can transport large quantities of drinking water from the water tank to the sink or basin very quickly. In contrast, foot pumps in a diaphragm or piston version are out of sight, but functional and practical for on-board use in cooking and sanitary areas. When it comes to safety equipment, stationary bilge pumps are part of the equipment standard, not only on traditional ships. On wooden boats, bilge pumps or submersible marine pumps with float switches are usually part of the basic equipment. A further area of application for marine pumps is the heating and propulsion system - this is where centrifugal pumps or circulation pumps for the hot water circulation of the heating system, marine oil-change pumps, as well as fuel and transfer pumps are required.
- Rigg & sail
- Rope & cordage
- Anchoring & mooring
- Hull & deck
- Cabin & comfort
- Paint & boatbuilding
- Electrics & engine
- Pumps & sanitation
- Safety & VHF radio
- Navigation & books
- Commercial shipping
Pumps
The GUSHER 30 is the largest manual bilge pump from WHALE, with a maximum flow rate of 117 litres per minute (at 70 strokes).The housing of this durable double diaphragm pump, which has been tried and tested for decades, is made of powder-coated die-cast aluminium alloy.Coating colour white. Hose connection 38 mm.Self-priming up to a maximum of 4 m, maximum pump height 4 m.No tools are required for inspection and cleaning. Long, removable lever with safety rope. Easily pumps oily bilge water or grey water.Available as a standard version (BP 3000), as a version for bulkhead mounting (BP 3010) or for underdeck mounting (BP 3020). In conjunction with the below deck conversion kit (AS 3020), the standard pump can also be converted for underdeck mounting.According to the manufacturer, the pump is approved for use as an emergency fire pump on some ships.In accordance with ISO15083 the WHALE GUSHER 30 is suitable as a primary bilge pump for vessels from 12 metres hull length. Approved by Lloyds (MCA) and USCG.
Heavy brass plunger pump. Very nice sturdy bilge pump.Seals of oil-resistant nitrile rubber. Capacity 0.3 l/pump. Outlet for hose 19 mm. Comes in different designs: - Intake with foot strainer for pumping directly from the bilge- Intake with 19mm hose adaptor- Intake with outer thread 1".
Proven bilge pump with robust housing of white plastic for mounting behind the bulkhead or below the deck with through reaching pump handle (bulkhead pump, below deck pump), especially suited for the installation in the sanitary areas. The efficient membrane pump is easy to maintain without tools through the large screw-off inspection port. Self priming up to 4,5m, maximum delivery height: 4,5m. For hose fittings of 38mm. Very well suited as a head pump, for example, for LAVAC POPULAR or ZENITH toilets (vacuum pumps). Type HENDERSON MK5 U/D, white.
Proven, very powerful bilge pump (diaphragm bilge pump) WHALE Gusher MK3 Standard BP3708 for mounting on the bottom or on the bulkhead.The sturdy housing is made of epoxy coated light metal, color yellow. The diaphragm is made of neoprene rubber. The lever is removable and has a care line.The pump is easy to maintain because all parts are easily accessible.Connection for hoses 38 mm.The pump is also available in a version for mounting below deck.
Proven diaphragm pump with robust housing made of black PVC, with universal mounting options that allow three different mounting positions.The pump can be converted for below deck/bulkhead mounting using the conversion kit (DP9906). Easy to service without tools through the large screw cap inspection opening.Self-priming up to max. 4.5m, pump height max. 4.5m. Can be used for 38 mm hoses.In accordance with ISO15083, the HENDERSON/WHALE MK5 is suitable as a main bilge pump for vessels with a hull length of 12 metres or more. Approved by Lloyds (MCA) and USCG.
Extremely robust hand pump for pumping almost all liquids, even hot ones. The pump is well suited as an oil change and diesel pump. The pumps are not self-priming!The housing is completely made of cast iron and then varnished. The wings and valves are made of brass. The handle of the pump is made of wood (in the case of article 4626-010 the handle is made of varnished cast iron).On both sides there is an inch BSP female thread.Available with pump body made entirely of bronze on request.
Powerful membrane bilgepump. Housing of black plastic. Removable handle with lanyard. Design (BP 4402). Attachment for hoses 38 mm.
Bilgepumpe, powered by nature.A clever idea from Sweden: a plastic pump fitted between a strong polyester strap attached to mooring lines is worked simply by the power of wind and waves to pump up to 2500 litres water per day from the bilge of your boat.No electricity required.The strap with two loops has a load capacity of up to 1500 kg and is simply hooked between one of the mooring lines.A neoprene cover protects the pump against sunlight.<brComes with a siphon hose of 3,00 m. A siphon hose extension is available separately. Shackles or hooks are not supplied.
Proven manual pump made from plastic for water and other liquids.Suitable for a tube diameter of 25 mm.Measurements:drum diameter: 50 mm,length over all: 500 mm.
Plastic manual bilge pump with membrane and vents of oil-proof nitrile rubber. The pump can be mounted very compactly (horizontally or vertically), so that eight different hose positions are possible. Self-priming (max. 2.5 m). Assets: - 25 mm gland, - Inlet, 30 l/min (capacity, 0.5 l/pump), - Handle length, 290 mm, - Weight, 500 g, - Color: body, blue; handle, black.
High-capacity plastic manual bilge pump (color: blue) with vent and membrane of oil-proof nitrile rubber. The pump is self-priming (max. 2.5 m).Comes without hose attachments (must be ordered seperatly, see Accessories).Inlet: 50 l/min (capacity, 0.85 l/pump).Handle length: 400 mm. Weight, 1 kg.Dimensions: 240 x 170 x 150 mm.Detachable lever. An inspection port allows easy cleaning of the pump.
High-capacity plastic manual bilge pump (color: blue) with vent and membrane of oil-proof nitrile rubber. The pump is self-priming (max. 3 m).Comes with straight hose attachment for 38 mm hose.Inlet: 50 l/min (capacity, 0.85 l/pump).Handle length: 400 mm, weight: 1 kg.Dimensions: 240 x 170 x 150 mm.Removable lever. An inspection port allows easy cleaning of the pump.
A manual bilge pump with unique features: Simple and space-saving bulkhead mounting, closed extruding only by 35 mm, operable at any time by a lever (elongated 320 mm long) that is extricable housed in the cover. Universal installation of the pump with attached hose couplings (25 or 38 mm), that can freely rotate, are angulated and detachable. Easy maintenance and simple membrane replacement. Materials: the body of the pump (grey) and cover (white) are made from plastic, lever stainless steel, membrane and valve are oil resistant nitrile rubber. Employing the integrated bypass an additional electric bilge pump can be used. Capacity 1l/hoisting, weight 920 g.
Plastic, with outlet hose (80 cm) and attachable inlet hose (30 cm), Hose diameter 25 mm (1"). Universal pump: as a bilge pump or for for pumping other liquids; gas- and oil-proof.
The FAABORG bilge pump is currently not available. A true Classic from the Danish iron foundry Faaborg, which has been producing equipment and accessories for fishing boats and wooden ships since 1855. This typical pump was used in the past on traditional professional vessels, especially in fishing.The heavy piston pump made of hot-dip galvanized cast steel is self-priming up to 4 m, it simply pumps the water on deck as it is common on wooden fishing cutters, no special breakthrough on board is required!With the long swivel pumping is very effective. The output is 1.8 l per stroke.The rubber sleeve of the adjustable steel piston is oil resistant.The pump mechanism can be mounted in different positions to the outlet. With BSP thread on the bottom, into which a suction pipe (must be made on board) or an (optional) hose nozzle for a suction hose is screwed.
Powerful membrane bilgepump. Housing of black plastic, removable handle with lanyard. Design with mounted deck/bulkhead feed through and white valve (BP 4410). Attachment for hoses 38 mm.
Compact, light membrane bilge pump.Housing made of black plastic with blue cover.Attachments are available for either 25 mm or 38 mm hoses.Shipping by default with membrane and valves made from robust neoprene rubber.Model with permanent plastic handle (BP 9005).
Compact, light membrane bilge pump. Housing of black plastic with blue cover. Attachments for both 25 or 38 mm hoses. Design with removable stainless steel handle with black grip and lanyard (BP 9021). The pump is also available with a membrane and valves made from nitrile rubber, especially for pumping oil.
Compact, light membrane bilgepump. Housing of black plastic. Attachments for both 25 or 38 mm hoses. Belowdecks design with mounted deck/bulkhead feed through and white valve (BP 9013). Removable stainless steel handle with black grip and safety lanyard (BP 9021).
A very heavy, sturdy membrane hand pump. Self-priming. Body of painted cast iron.Strong EPDM rubber membrane and easily accessible rubber ball vents.Pumps bilge water, grey and black water.Not to be used for pure fuel or oil. The pump handle is removable. The pump is intended for vertical use. Attachment: both sides 1 1/2" inner threads. Output: 40 l/min (capacity 0.65 l/pump). Weight: 12 kg.Spares are available.
Very powerful, self-priming electrical diaphragm pump with reliable industrial motor.This Rheinstrom diaphragm pump has been found to be very reliable over many years. It can be used as a bilge pump, a grey water pump and a delivery pump.Constant delivery rate, high safety against clogging, very good cleaning possibilities.Made of hard-wearing materials, the body is made of seawater-proof cast bronze.Fast and easy cleaning and maintenance and direct access to the valves are obtained by simply opening the lid of the pump. The discharge and suction side may be altered.Technical dataPump performance: 40 l/minDelivery head: 10 mSuction height: 3,5 mConnection: 38 mm hose connectionMotor: 110 WWeight: 9,5 kgA repair kit is available.
Self-priming electric water pump with with nitrile rubber impeller. The pump body is made of nickel-plated brass. The pump is dry self-priming up to 1.5 m height.The connections have a BSP female thread. A direct hose connection to the connection pieces is also possible.Available in two power ratings for 12 or 24 volts.Also available for 220 volts, see matching items. See similar articles.
WHALE GULPER type 220: Electric membrane pump for pumping the bilge or emptying the head or holding tank (grey water pump). Self-priming. Suction lift max. 3 m, dicharge head max. 3 m, combined suction lift / discharge head max. 4m.Odorless running, vibration absorbing rubber feet.Universal installation due to swiveling pump heads.For tube 19mm. Weight 1.5 kg. Dimensions: L x W x H = 273 x 111 x 117 mm. Spare-parts sets available.
High-performance bilge pump, available in various sizes for 12V or 24V systems. Discharge head up to 3 m.The snap-off plastic housing can be opened easily for maintenance and cleaning. Low power requirements.Stainless-steel shaft with a high-quality seal.Built in Italy by MARCO.
A new generation of diaphragm pump in the one compartment design by pump specialist JABSCO.Ideal for the draining of shallow bilges and shower drains.Maintanance is simplified by the filterless design and the pump is indeed free of clogging.Characteristics:Flow rate: Nominal 16 Litres/min. Self-priming from dry up to 3m (10ft) Flexible installation Dry running capability
The RULE-MATE is an automatic bilge pump, controlled by an electronic water level sensor integrated into the housing and does not require a separate float switch. As soon as water reaches the sensor area, the pump starts automatically and pumps out the bilge water. When the water level drops again, the pump switches off automatically.According to the manufacturer, the RM500, RM800 and RM1100 models start at a water level of approximately 5 cm and switch off again when the residual water level is approximately 0.9 cm. The RM2000 starts at a water level of approximately 7 cm.Unlike the time-controlled automatic pumps of the RULE-AUTOMATIC/RA series (see Similar Products), the RULE-MATE does not start at fixed intervals during normal operation, but reacts to the actual water level. The manufacturer refers to this function as ‘Auto Sense Intelligence’. If the sensor is obstructed by debris or the pump runs without delivering water, a backup function prevents continuous operation: the pump then switches to a cyclic check mode with a 2.5-minute interval.The actual flow rate depends on the delivery head, the hose routing and the connection diameter used. As the delivery head increases, the flow rate decreases. The TOPLICHT product table therefore lists not only the maximum flow rate but also the flow rate at 1 m water column; depending on the model, this ranges between 23 and 93 l/min for the RULE-MATE pumps on offer.The series features a plastic housing with an easily removable strainer base plate. The motor is fully enclosed, and the shaft is made of stainless steel and fitted with a special seal. The unit is supplied with straight hose connections. Depending on the model, a range of flow rates, connection diameters and operating voltages are available.Technical featuresAutomatic bilge pump with integrated electronic water level sensorAvailable in versions for 12 V or 24 V on-board power supplyNo separate float switch requiredAutomatic start-up when water level is detectedAutomatic shut-off when water level dropsStart-up water level RM500/RM800/RM1100: approx. 5 cmShut-off RM500/RM800/RM1100: approx. 0.9 cm residual water levelStart-up water level RM2000: approx. 7 cmBackup function with 2.5-minute test mode in the event of a faulty sensor or lack of water flowPlastic housing with easily removable strainer base plateFully enclosed motorSupplied with straight hose connectors
Extremely low-profile, submersible pump with good power, by the renowned pump manufacturer WHALE, which can also be placed between frames and floor boards.Equipped with a built in, maintenance free 'electric field sensor' as integrated float switch, removable sieve and non-return valve. Drains to down 9 mm.Outflow hose adjustable from horizontal to vertical.Versions: SUPERSUB SMART 5212 has a max. pump output of 40 l/min and 34 l/min at 1 meter height. SUPERSUB SMART 1212 and 1224 have a pump output of 66 l/min and 47 l/min at 1 meter height.
WHALE GULPER type 320: Electric membrane pump for pumping the bilge or pumping out the head or holding tank (grey water pump). Self-priming. Suction lift max. 3m, dicharge head max. 3 m, combined suction lift / discharge head max. 4m.Odorless running, vibration absorbing rubber feet.Universal installation due to swiveling pump heads.A variable tube adaptor connects the GULPER 320 to 19mm or 25mm tube. Weight 1.6 kg. Dimensions: L x W x H = 273 x 111 x 117 mm. Spare-parts sets available.
The tried-and-tested RULE-AUTOMATIC (RA) bilge pumps feature a built-in microprocessor which checks for the presence of water every 150 seconds by briefly activating the pump (without a mechanical switch). Power consumption for the test run is low at approx. 0.2–0.5 Ah per day. Whilst conventional bilge pumps with float switches typically activate at a water level of around 5 cm, the RULE-AUTOMATIC switches on at around 1.6 cm and pumps the bilge water down to a residual water level of around 0.6 cm.The series features a plastic housing, an easily removable strainer base plate and a quiet-running, fully enclosed motor. The non-return valve reduces the backflow of water into the bilge, whilst concealed vents in the pump housing prevent air pockets in the hose installations. The threaded outlet allows the use of different hose connectors, depending on the specific model and connection diameter.Technical featuresAutomatic bilge pump for 12-volt on-board electrical systemsElectronic water level control without a mechanical float switchTest run every 150 secondsActivation level approx. 1.6 cmPumps down to approx. 0.6 cm residual water levelPlastic housing with removable strainer base plateFully enclosed motorNon-return valve to reduce backflow of waterConcealed vents in the housing to prevent air pockets
Submersible bilgepump with strong permanent magnet motor and special shaft seals.The outer cover can be removed for inspection.Shaft of rust-free steel.These pumps are only partially protected against dry-running, so the installation of the optional floating or sensor switch is recommended.
Flat, powerful bilge pump for tight spaces with freely adjustable hose outlet (vertical/horizontal) for 3 different hose diameters (19, 25 and 28 mm). All hose nozzles have lip check valves, the motor unit is removable for cleaning, maximum pumping height is 3.4 m.Pumping capacity: 3373 l/h at the same level.2400 l/h at 1 m height difference (1 mWS).Available as standard pump (type LP900D) or as automatic pump (type LP900S) with integrated sensor switch.The sensor has 3 switching modes: in mode "L" the pump switches on at a water height of 33 mm, in mode "H" at 50 mm, in mode "Time" the pump checks every 150 seconds by a short start if water is present and then pumps until the bilge is empty.
Powerful submersible pump from RULE. The pump is made of sturdy plastic and is ideal for smaller boats due to its light and compact nature.The motor is fully enclosed and runs very quietly. The shafts can not rust and are specially sealed against water penetration.The inlet strainer of the pump can be easily removed to clean the pump. The check valve prevents water from flowing back into the bilge, and the ventilated housing optimally prevents air pockets.A thermal shutdown prevents overheating and protects the pump.Also available as RULE AUTOMATIC (RA) automatic pumps. See under similar products.
Extremely low-profile, submersible pump with good power, by the renowned pump manufacturer WHALE, which can also be placed between frames and floor boards.Removable sieve, outflow hose adjustable from horizontal to vertical.This version requires a separate pump/bilge switch (see accessories). Article 1441-111 comes with a non-return valve. Versions:SUPERSUB 5012 has a max. pump output of 32 l/min and 25 l/min at 1 meter height. , SUPERSUB 1012 has a max. pump output of 66 l/min and 47 l/min at 1 meter height.Also available in the WHALE SUPERSUB SMART version with automatic sensor switch.
Powerful impeller pump with bronze pump head and impeller made of nitrile rubber (oil-resistant), dry self-priming up to 1.20 m. Developed for pumping bilge water. Dry-running protection up to 20 minutes. Capacity 32 l/min at 3 m (0.3 bar) or 27 l/m at 5 m (0.5 bar), suitable for continuous operation.Dimensions 190x120x80 mm.Versions for 12V or 24V on-board voltage are available. Connection 3/4" (inside).
This self-priming bilge and deck wash pump is suitable for delivering sea water. It is completely made of bronze and stainless steel. Due to its hard-wearing industrial motor a longlasting and reliable operation is guaranteed. Before it is run for the first time it has to be filled with water. Furthermore it is advisable to install a socket safety valve or a foot operated valve into the suction pipe. The pump is non-reactive to sand (particle size up to 2 mm). The model 4 E is totally maintenance-free due to the use of a freely running impeller wheel and a very modern axial face seal. The max. operating time is 1 – 2 hoursTechnical dataOutput:50 l/minHeight pumped: 13 mSuction lift: 3 mAttachment: 3/4" BSP with inner threadsWeight: 7 kg
Classic solid brass galley pump.Above-table model, outlet and pump handle adjustable to any angle.Combined hose attachment for 16 mm or 19 mm hose.Spare parts kit is Art-Nr. 4613-100.
Compact double-membrane pump that delivers on both lifting and pushing movements.Hose attachments are adjustable.Can also be used with salt water. Self-priming (max. 2 m)With good and very steady output, approx. 12 l/min.Hose attachment 13 mm. Spare parts kit is 4608-100.
Self-priming, smooth-running piston pump made from plastic.Twisting spigot, Maximum flow rate 7 l/min.Made for fresh water and sea water.Tube coupling 13mm.Spare parts kit is Art-Nr. 4602-101.
Functional plastic piston pump.The swiveling spout and the pump's pistons are made of chromed brass.Hose attachment 13-16 mm.White plastic body.Spare parts kit is Art-Nr. 4644-100.
Self-priming, perfectly smooth-running piston pump.Piston and spigot are made from aluminium. Height adjustable from 90 to 250 mm.Utilizing the small mounting base the pump can easily be installed between two sinks.Spigot length 125mm. Tube coupling 13 mm.Maximum flow rate 8 l/min.Qualified for fresh and salt water.Spare parts kit Art-Nr. 4609-100.
Proven membrane foot pump for fresh water.Delivers with every push, self-priming (max. 1.5 m), output approx. 5 l/min.Dimensions: D= 89 mm; height 70 mm;Hose attachment 13 mm. Spare parts kit is Art-Nr. 4606-101.
Inexpensive membrane pump for fresh water.Foot pump that delivers with every push, self-priming (max. 1.5 m).Output approx. 5 l/min.Hose attachment 13 mm.
Proven piston pump with handle operation.Plastic, available in white or black.Spout and handle of chromed brass, self-priming.Hose attachment 13-16 mm. Spare parts kit is Art-Nr. 4644-103.
The pump AQUA KING II Standard 3.0 is a powerful fresh water pump in marine quality. The pump has been proven for years, has a quiet running and offers a usage comfort like at home.The 4-chamber diaphragm pump is self-priming up to 1.5 m and may run dry. The encapsulated pressure switch start at 2.8 bar and off again at 3.8 bar. The pump is equipped with an integrated bypass for precise and controlled dosing and even water flow, a pressure compensation vessel is not required.Technical features:4-chamber diaphragm pump,max. flow rate: 11.3 l/min, 3GPM (gallons per minute)pressure: 2,8 - 3,8 bar,for supplying up to 3 taps,dry-self-priming and dry-running safe,motor and pump head drive made of metal,pump head and mounting foot made of PP,rubber bearing for a high running smoothness,the motor is explosion-proof,connection thread 1/2" external thread,delivery includes two hose nozzles for 13 mm hose, which can be screwed onto the thread with a quick-release fastener.
The pump AQUA KING II Junior 2.0 is a powerful fresh water pump in marine quality. The pump has been proven for years, has a quiet running and offers a usage comfort like at home.The 4-chamber diaphragm pump is self-priming up to 1.5 m and may run dry. The encapsulated pressure switch start at 1 bar and off again at 2 bar. A pressure compensation vessel is not required.Technical features:4-chamber diaphragm pump,max. flow rate: 7,6 l/min,pressure: 1 - 2 bar,for supplying up to 3 taps,dry-self-priming and dry-running safe,motor and pump head drive made of metal,pump head and mounting foot made of PP,rubber bearing for a high running smoothness,the motor is explosion-proof,connection thread 1/2" external thread,delivery includes two hose nozzles for 13 mm hose, which can be screwed onto the thread with a quick-release fastener.
The pump AQUA KING II Standard 3.0 is a powerful fresh water pump in marine quality. The pump has been proven for years, has a quiet running and offers a usage comfort like at home.The 4-chamber diaphragm pump is self-priming up to 1.8 m and may run dry. A pre-filter ensures clean drinking water. The encapsulated pressure switch start at 2.8 bar and off again at 3.8 bar. The pump is equipped with an integrated bypass for precise and controlled dosing and even water flow, a pressure compensation vessel is not required.Technical features:4-chamber diaphragm pump,max. flow rate: 15.1 l/min,pressure: 2.8 - 3.8 bar,for supplying up to 4 taps,comes with a pre-filter,dry-self-priming and dry-running safe,motor and pump head drive made of metal,pump head and mounting foot made of PP,rubber bearing for a high running smoothness,the motor is explosion-proof,connection thread 1/2" external thread,delivery includes two hose nozzles for 13 mm hose.Angled hose nozzles are also available.
The MARCO UPE pumps are electronically controlled freshwater gear pumps designed for pressurized onboard water systems. They deliver constant water pressure without pulsation, operate quietly, save space, and are suitable for multiple outlets.The MARCO UPE pumps are self-priming gear pumps with electronic speed control and smooth, gradual start-up. Their speed automatically adjusts to the water demand, eliminating pressure fluctuations and pulsation in the system. An accumulator tank is only required when using rigid or very short pipes or solenoid valves.The pump housings are made of nickel-plated brass, and the spindles are stainless steel. The durable PEEK gears ensure high pressure, quiet operation, and excellent temperature resistance. Integrated non-return valves are included as standard. The pumps support both 12 V and 24 V operation. Connections are BSP female threads, and each pump is supplied with matching stainless-steel hose tails.The electronic control enables soft start and stop, reducing power consumption and water waste while significantly extending component life — up to three times longer than comparable models. The electronic system constantly monitors pressure, current, and voltage, provides protection against short circuits and overvoltage, and automatically stops the pumps when the tank is empty.These pumps run very quietly, require minimal space, and ensure reliable water supply on board.Models:· Type UP2/E: for max. 2 outlets, without pre-filter· Type UP3/E, UP6/E, UP12/E: for max. 3 outlets, with pre-filter· Type UP14/E: for max. 3 outlets, with pre-filter and PCS control panelKey Advantages at a Glance:· Electronic speed control, adjusts to water demand· Smooth, gradual start and stop· No pressure fluctuations, no pulsation· Self-priming (not dry self-priming)· No accumulator tank required except with rigid/short pipes or solenoid valves· PEEK gears: high pressure, quiet running, temperature resistant· Integrated non-return valves· Electronic monitoring of pressure, current, voltage· Protection against short circuit and overvoltage· Automatic shut-off when tank is empty· Multi-voltage: 12 V / 24 V· BSP female thread connections, incl. stainless-steel hose tails· Very quiet operation· Robust materials: nickel-plated brass, stainless steel
The very quiet running WHALE WaterMaster is a four chamber diaphragm pump - a further development of the tried and tested UNIVERSAL pump.The pump runs dry without damage (within reason) and is self priming up to 3m, it delivers a smooth constant flow from a specially designed diaphragm.The pump has a fully sealed protective motor housing with completely integrated electronics according to IP 65 and is suitable for use with salt or fresh water.The shipment includes a strainer to protect the pump from debris.Simple installation: WHALE QUICK-CONNECT - 15 mm quick connect plumbing or ½" horsetails or 13mm hose. Measurements (L x W x H): 209 x 179 x 125, Weight: 1600 g.
Very quiet running pressurized water pumps for simultaneous supply of fresh water taps on board. The compact fresh water supply pumps are rubber-mounted, self-priming and safe to run dry and they have a sealed protection switch. Quick Connect ports for hose connection without tools allow easy installation and servicing.Par-Max 1: Suitable for use on small boats with one or two taps. Comes without water strainer.Par-Max 2 und Par-Max 3: Pressurized water pumps for simultaneous supply of up to 3 fresh water taps on board. A Quick Connect water strainer is included.Par-Max HD4 und Par-Max HD5: High performance pressure water pumps for simultaneous supply of up to 5 fresh onboard water taps. The lower housing is made of powder-coated cast aluminum. The base plates have the same hole spacing as corresponding FLOJET pressurized water pumps. A Quick Connect water strainer is included.
Small 12 volt/24 volt pumps for simple drinking water systems.Two-sided hose attachment can be used for either 10 mm or 13 mm (adapter).Not self priming. Available in PREMIUM version for 12 and 24 volts or HIGH FLOW version with higher pump output (only for 12 volts).- low weight, is simply inserted into the pipe or hose system- can be used as a pressure booster in manual or electric pump systems- low power consumption and very quiet- for fresh and salt water
Universal Pressure Pump 18 ltrs/min (4.75 US gals/min).High capacity demand and washdown pressure pump.Services up to 6 taps.- Quiet operation- Runs dry without damage- Inlet strainer included- Quick Connect ports with adaptors included- Suitable for use with saltwater and freshwater- Self-priming up to 3 m (10 ft)- Smooth constant flow- Extra protection and safety with wires and pressure switch housed internally- Universal mounting arrangement fits any existing installation.- May also be used with salt water.Supplied with Quick Connect inlet and outlet for fast connection directly to System 15 plumbing. Includes pre-strainer/filter that pivots to suit plumbing direction. 2 x 13mm barbed hose connections and 2 x 1/2″ BSP threaded tails are also included for connection to non-Quick Connect 15 plumbing.
This pump is specially developed for maritime use in pressure-water installations. Made in the USA by SHURFLO.Benefits:- for direct supply of one tap!- not dry self priming, must be installed at or below tank level,- dry-running safe single chamber pump,- output: 3,8 l/min,- sturdy motor,- very smooth performance, very silent- with hose nozzles for 10 mm tube.
This compact automatic demand fresh water pump offers durability and dependability making it ideal for low volume, intermittent duty applications.The 105 pump self-primes up to 0,75 m / 2.5 feet vertical while delivering over 1.0 GPM.A 12 volt low power consumption motor, equipped with thermal protection and long life pressure switch rated to 2 bar / 30 PSI, provides high pump performance and reliability.Features:- Automatic Demand up to 2 bar / 30 PSI,- Dry self Priming up to 0,76 m vertical,- Long Life Pressure Switch,- Thermally Protected,- Delivers 4 l/min / 1.0 GPM,Dimensions: 173 x 100 x 62 mmHose fitting for 10 mm hose.
The pump AQUA KING II Supreme 5.0 is a powerful fresh water pump in marine quality. The pump has been proven for years, has a quiet running and offers a usage comfort like at home.The 4-chamber diaphragm pump is self-priming up to 1.8 m and may run dry. A pre-filter ensures clean drinking water. The encapsulated pressure switch start at 2.8 bar and off again at 3.8 bar. The pump is equipped with an integrated bypass for precise and controlled dosing and even water flow, a pressure compensation vessel is not required.Technical features:4-chamber diaphragm pump,max. flow rate: 18.9 l/min,pressure: 2.8 - 3.8 bar,for supplying up to 5 taps,comes with a pre-filter,dry-self-priming and dry-running safe,motor and pump head drive made of metal,pump head and mounting foot made of PP,rubber bearing for a high running smoothness,the motor is explosion-proof,connection thread 1/2" external thread,delivery includes two hose nozzles for 13 mm hose, which can be screwed onto the thread with a quick-release fastener.
Small submersible pumps for simple drinking water systems. The pumps can simply be lowered into the tank or a water canister.Hose connection optionally for 10 mm or 13 mm (push-on adapter supplied). Available in PREMIUM version for 12 or 24 volts or HIGH FLOW version with higher pump output for 12 volts.- Lightweight, simply inserted into the pipe or hose system- can be used as a pressure booster in manual or electric pump systems- low power consumption and very quiet- for fresh or salt water
Self-priming electric water pump with with nitrile rubber impeller. The pump body is made of nickel-plated brass. The pump is dry self-priming up to 1.5 m height.The connections have a BSP female thread. A direct hose connection to the connection pieces is also possible.Available in two power ratings for 12 or 24 volts.Also available for 220 volts, see matching items. See similar articles.
Efficient electric pump with bronze pump head and impeller of nitrile rubber (oil-proof), dry self-priming to 1.2 m.Power 32 l/min at 3 m (0.3 bar) or 27 l/m at 5 m (0.5 bar), intended for endurance use.Dimensions 190 x 120 x 80 mm.Attachment 1/2" (inner) or 25mm hose.Versions for 12V or 24V on-board voltage are available.Also available is the JABSCO UTILITY PUPPY 2000 version specially designed for pumping bilge water with 20-minute dry-running protection.
An exceptionally practical tool for removing impellers without damaging the pump housing.Body and jaws of aluminum, shaft of stainless steel.Dimensions, approx. 140 x 165 mm (W x H). Weight, 450 g.
Self-priming impeller pump with free shaft end. for socket mounting. Equipped with neoprene impeller for use as sea or fresh water pump.The pump housing is made of bronze, the axle with ball bearings is made of stainless steelThe details regarding the output refer to an input speed 1500 U/min and back pressure at 0.3 bar.
Self-priming electric pump for transfer of fresh or salt water with flexible impeller of nitrile rubber which allows the problem-free transit of small particles. Nickel-plated brass body, shaft in stainless steel. AISI 316L. Voltage: 230V-50Hz.Consumption: 3,3 A.Fuse: 4 A.Selfpriming up to 1,5 m height.Flow rate: 30l/min.Pressure: 1 bar.Ports: 1/2" Innengewinde (BSP) or hose diameter: 25 mm.Motorpower: 550 W.Weight: 7,3 kg.Also available for 12 volt or 24 volt. See under similar products.
This universal feed pump for freshwater and seawater has a hard-wearing impeller made of nitrile rubber. The motor is equipped with an integrated waterproof switch with three positions (forward/off/reverse) so that the flow direction can be changed.This compact design makes the impeller pump ideal for transferring water or grey water, as well as for emptying bilges and grey water. The pump body is made of nickel-plated brass and the impeller is made of hard-wearing nitrile rubber. The pump is dry self-priming up to a height of 1.5 metres. The connecting pieces allow direct hose connection, but also have BSP internal threads, so that connection with appropriate fittings is also possible.Available in two performance levels for 12 over 24 volts.You can find other MARCO pumps in the UP1 series under the "Similar products" tab.
Powerful impeller pump with bronze pump head and impeller made of nitrile rubber (oil-resistant), dry self-priming up to 1.20 m. Developed for pumping bilge water. Dry-running protection up to 20 minutes. Capacity 32 l/min at 3 m (0.3 bar) or 27 l/m at 5 m (0.5 bar), suitable for continuous operation.Dimensions 190x120x80 mm.Versions for 12V or 24V on-board voltage are available. Connection 3/4" (inside).
With mechanical cone clutch.These pumps work via a V-belt and can be coupled by hand when needed. Pump with high output (specification at 1500 U/min and a back pressure of 0.3 bar) and self priming from dry. Well suited as an emergency pump or as a deck-wash pump. Pump housing, bronze; stainless steel shaft; neoprene impeller.
Dry self-priming, belt-driven impeller pumps, can be engaged/disengaged by means of an electric magnetic coupling, 12V or 24V.With electric magnet clutch, 12V or 24V.Pump with high output (specification at 1500 U/min and a back pressure of 0.3 bar).Well suited as emergency pump or as a deck-wash pump.Pump housing, bronze, stainless steel shaft, neoprene impeller.
The self-priming 230 V multi-purpose pump JABSCO 53040 UTILITY is a portable pump for filling, pumping out and transferring fresh, salt, and bilge water.The pump is made from bronze, the impeller from oil-proof nitrile rubber, the shaft from stainless steel with a carbon-ceramic mechanical shaft seal. The compact pump can be deployed in multiple ways with its practical handle, is rapidly self-priming from dry up to 4m and will handle hard or soft solids.Air cooled alternate current motor 230 V / 50 Hz, protection class IP55, 0,25 kW at 1400 rpm. With built-in dry-running protection for up to 30 minutes after initial prime
Very powerful, self-priming electrical diaphragm pump with reliable industrial motor.This Rheinstrom diaphragm pump has been found to be very reliable over many years. It can be used as a bilge pump, a grey water pump and a delivery pump.Constant delivery rate, high safety against clogging, very good cleaning possibilities.Made of hard-wearing materials, the body is made of seawater-proof cast bronze.Fast and easy cleaning and maintenance and direct access to the valves are obtained by simply opening the lid of the pump. The discharge and suction side may be altered.Technical dataPump performance: 40 l/minDelivery head: 10 mSuction height: 3,5 mConnection: 38 mm hose connectionMotor: 110 WWeight: 9,5 kgA repair kit is available.
The pump AQUA KING II Standard 3.0 is a powerful fresh water pump in marine quality. The pump has been proven for years, has a quiet running and offers a usage comfort like at home.The 4-chamber diaphragm pump is self-priming up to 1.5 m and may run dry. The encapsulated pressure switch start at 2.8 bar and off again at 3.8 bar. The pump is equipped with an integrated bypass for precise and controlled dosing and even water flow, a pressure compensation vessel is not required.Technical features:4-chamber diaphragm pump,max. flow rate: 11.3 l/min, 3GPM (gallons per minute)pressure: 2,8 - 3,8 bar,for supplying up to 3 taps,dry-self-priming and dry-running safe,motor and pump head drive made of metal,pump head and mounting foot made of PP,rubber bearing for a high running smoothness,the motor is explosion-proof,connection thread 1/2" external thread,delivery includes two hose nozzles for 13 mm hose, which can be screwed onto the thread with a quick-release fastener.
WHALE GULPER type 220: Electric membrane pump for pumping the bilge or emptying the head or holding tank (grey water pump). Self-priming. Suction lift max. 3 m, dicharge head max. 3 m, combined suction lift / discharge head max. 4m.Odorless running, vibration absorbing rubber feet.Universal installation due to swiveling pump heads.For tube 19mm. Weight 1.5 kg. Dimensions: L x W x H = 273 x 111 x 117 mm. Spare-parts sets available.
The pump AQUA KING II Junior 2.0 is a powerful fresh water pump in marine quality. The pump has been proven for years, has a quiet running and offers a usage comfort like at home.The 4-chamber diaphragm pump is self-priming up to 1.5 m and may run dry. The encapsulated pressure switch start at 1 bar and off again at 2 bar. A pressure compensation vessel is not required.Technical features:4-chamber diaphragm pump,max. flow rate: 7,6 l/min,pressure: 1 - 2 bar,for supplying up to 3 taps,dry-self-priming and dry-running safe,motor and pump head drive made of metal,pump head and mounting foot made of PP,rubber bearing for a high running smoothness,the motor is explosion-proof,connection thread 1/2" external thread,delivery includes two hose nozzles for 13 mm hose, which can be screwed onto the thread with a quick-release fastener.
The pump AQUA KING II Standard 3.0 is a powerful fresh water pump in marine quality. The pump has been proven for years, has a quiet running and offers a usage comfort like at home.The 4-chamber diaphragm pump is self-priming up to 1.8 m and may run dry. A pre-filter ensures clean drinking water. The encapsulated pressure switch start at 2.8 bar and off again at 3.8 bar. The pump is equipped with an integrated bypass for precise and controlled dosing and even water flow, a pressure compensation vessel is not required.Technical features:4-chamber diaphragm pump,max. flow rate: 15.1 l/min,pressure: 2.8 - 3.8 bar,for supplying up to 4 taps,comes with a pre-filter,dry-self-priming and dry-running safe,motor and pump head drive made of metal,pump head and mounting foot made of PP,rubber bearing for a high running smoothness,the motor is explosion-proof,connection thread 1/2" external thread,delivery includes two hose nozzles for 13 mm hose.Angled hose nozzles are also available.
The MARCO UPE pumps are electronically controlled freshwater gear pumps designed for pressurized onboard water systems. They deliver constant water pressure without pulsation, operate quietly, save space, and are suitable for multiple outlets.The MARCO UPE pumps are self-priming gear pumps with electronic speed control and smooth, gradual start-up. Their speed automatically adjusts to the water demand, eliminating pressure fluctuations and pulsation in the system. An accumulator tank is only required when using rigid or very short pipes or solenoid valves.The pump housings are made of nickel-plated brass, and the spindles are stainless steel. The durable PEEK gears ensure high pressure, quiet operation, and excellent temperature resistance. Integrated non-return valves are included as standard. The pumps support both 12 V and 24 V operation. Connections are BSP female threads, and each pump is supplied with matching stainless-steel hose tails.The electronic control enables soft start and stop, reducing power consumption and water waste while significantly extending component life — up to three times longer than comparable models. The electronic system constantly monitors pressure, current, and voltage, provides protection against short circuits and overvoltage, and automatically stops the pumps when the tank is empty.These pumps run very quietly, require minimal space, and ensure reliable water supply on board.Models:· Type UP2/E: for max. 2 outlets, without pre-filter· Type UP3/E, UP6/E, UP12/E: for max. 3 outlets, with pre-filter· Type UP14/E: for max. 3 outlets, with pre-filter and PCS control panelKey Advantages at a Glance:· Electronic speed control, adjusts to water demand· Smooth, gradual start and stop· No pressure fluctuations, no pulsation· Self-priming (not dry self-priming)· No accumulator tank required except with rigid/short pipes or solenoid valves· PEEK gears: high pressure, quiet running, temperature resistant· Integrated non-return valves· Electronic monitoring of pressure, current, voltage· Protection against short circuit and overvoltage· Automatic shut-off when tank is empty· Multi-voltage: 12 V / 24 V· BSP female thread connections, incl. stainless-steel hose tails· Very quiet operation· Robust materials: nickel-plated brass, stainless steel
A new generation of diaphragm pump in the one compartment design by pump specialist JABSCO.Ideal for the draining of shallow bilges and shower drains.Maintanance is simplified by the filterless design and the pump is indeed free of clogging.Characteristics:Flow rate: Nominal 16 Litres/min. Self-priming from dry up to 3m (10ft) Flexible installation Dry running capability
WHALE GULPER type 320: Electric membrane pump for pumping the bilge or pumping out the head or holding tank (grey water pump). Self-priming. Suction lift max. 3m, dicharge head max. 3 m, combined suction lift / discharge head max. 4m.Odorless running, vibration absorbing rubber feet.Universal installation due to swiveling pump heads.A variable tube adaptor connects the GULPER 320 to 19mm or 25mm tube. Weight 1.6 kg. Dimensions: L x W x H = 273 x 111 x 117 mm. Spare-parts sets available.
The very quiet running WHALE WaterMaster is a four chamber diaphragm pump - a further development of the tried and tested UNIVERSAL pump.The pump runs dry without damage (within reason) and is self priming up to 3m, it delivers a smooth constant flow from a specially designed diaphragm.The pump has a fully sealed protective motor housing with completely integrated electronics according to IP 65 and is suitable for use with salt or fresh water.The shipment includes a strainer to protect the pump from debris.Simple installation: WHALE QUICK-CONNECT - 15 mm quick connect plumbing or ½" horsetails or 13mm hose. Measurements (L x W x H): 209 x 179 x 125, Weight: 1600 g.
The self priming membrane type pump is especially suitable for pumping polluted liquids, such as toilet waste, bilge water.The robust pump casing is wholly made from plastic and is equipped with rotatable connectors with sleeves, which can easily be demounted. These contain tube valves.This construction guaranties a very flexible mounting, little danger of blockage and simple cleaning of the pump.The strong electric motor is capable of continuous operation. Pump capacity: 27 l/min Maximum suction height:: 3 m Maximum delivery height: 5 m Housing material: plastic, black Membrane material: neoprene rubber Valve material: natural rubber Current draw for 12 V DC 8 AMP Current draw for 24 V DC 5 AMP Hose fittings for 38 mm Weight: 3,7 kg Mesurements: 300 x 320 x 220 mm
Universal Pressure Pump 18 ltrs/min (4.75 US gals/min).High capacity demand and washdown pressure pump.Services up to 6 taps.- Quiet operation- Runs dry without damage- Inlet strainer included- Quick Connect ports with adaptors included- Suitable for use with saltwater and freshwater- Self-priming up to 3 m (10 ft)- Smooth constant flow- Extra protection and safety with wires and pressure switch housed internally- Universal mounting arrangement fits any existing installation.- May also be used with salt water.Supplied with Quick Connect inlet and outlet for fast connection directly to System 15 plumbing. Includes pre-strainer/filter that pivots to suit plumbing direction. 2 x 13mm barbed hose connections and 2 x 1/2″ BSP threaded tails are also included for connection to non-Quick Connect 15 plumbing.
Membrane pump for emptying holding tanks.^ Protected against dry-running, self-priming to 3 m, discharge height max. 4 m. Low power draw; 2.5 A (at 12 V)Inlet hose attachments on both sides 38 mm. Dimensions: 340 x 300 x 120 mm. Weight 2.2 kg.
This pump is specially developed for maritime use in pressure-water installations. Made in the USA by SHURFLO.Benefits:- for direct supply of one tap!- not dry self priming, must be installed at or below tank level,- dry-running safe single chamber pump,- output: 3,8 l/min,- sturdy motor,- very smooth performance, very silent- with hose nozzles for 10 mm tube.
This compact automatic demand fresh water pump offers durability and dependability making it ideal for low volume, intermittent duty applications.The 105 pump self-primes up to 0,75 m / 2.5 feet vertical while delivering over 1.0 GPM.A 12 volt low power consumption motor, equipped with thermal protection and long life pressure switch rated to 2 bar / 30 PSI, provides high pump performance and reliability.Features:- Automatic Demand up to 2 bar / 30 PSI,- Dry self Priming up to 0,76 m vertical,- Long Life Pressure Switch,- Thermally Protected,- Delivers 4 l/min / 1.0 GPM,Dimensions: 173 x 100 x 62 mmHose fitting for 10 mm hose.
The pump AQUA KING II Supreme 5.0 is a powerful fresh water pump in marine quality. The pump has been proven for years, has a quiet running and offers a usage comfort like at home.The 4-chamber diaphragm pump is self-priming up to 1.8 m and may run dry. A pre-filter ensures clean drinking water. The encapsulated pressure switch start at 2.8 bar and off again at 3.8 bar. The pump is equipped with an integrated bypass for precise and controlled dosing and even water flow, a pressure compensation vessel is not required.Technical features:4-chamber diaphragm pump,max. flow rate: 18.9 l/min,pressure: 2.8 - 3.8 bar,for supplying up to 5 taps,comes with a pre-filter,dry-self-priming and dry-running safe,motor and pump head drive made of metal,pump head and mounting foot made of PP,rubber bearing for a high running smoothness,the motor is explosion-proof,connection thread 1/2" external thread,delivery includes two hose nozzles for 13 mm hose, which can be screwed onto the thread with a quick-release fastener.
The sewage pump RHEINSTROM M is a self-priming diaphragm pump with bronze housing. Even bigger solids can be conveyed without damaging the pump because of the lip valves which have been installed. The self-locking valves make the pump non-reactive, i.e. it can be mounted to the side standing, hanging or sideways.Technical data:Output: 20 l / minHead: 8 mSuction height: 5 mSuction and pressure connection: 1 ½"Connection: 38 mm hoseWeight: 12 kg.
The perfect solution, for example, for emptying a waste water tank.Dry self-priming impeller pump with nitrile impeller and built-in stainless steel cutting wheel as chopper.Suction lift to 1.2 m, pump power max. 2700 l/h.Special feature: The pump works with a patented dry-running protection: when it runs dry, it immediately switches off, thereby hindering damage to the impeller.New activation of the pump through switching it off and on. Attachments:Inlet-1-1/2" (38 mm) Hose Barb and1-1/2" N.P.T. (Male). Outlet-1" (25 mm) Hose Barb. Dimensions: 286 x 106 x 92 mm.
High performance mercerator pump especially for sanitation waste.Pump head of black plastic or bronze.Self-priming up to 1,5 m.Attachments:Inlet for hose 38 mm,Pressure-side for hose 25 mm.Dimensions: 240 x 130 x 90 mm.
Membrane pump for emptying holding tanks.^ Protected against dry-running, self-priming to 3 m, discharge height max. 4 m. Low power draw; 2.5 A (at 12 V)Inlet hose attachments on both sides 38 mm. Dimensions: 340 x 300 x 120 mm. Weight 2.2 kg.
Robust diaphragm pump for extracting sewage from the pump specialist JABSCO. Dry self-priming up to 3.0 m. Full passage due to the use of lip valves. Universal and flexible installation, as both the pump head and the hose direction can be adjusted as required.Dimensions L x W x H: 278 x 161 x 132 mm. Available for 12 V or 24 V.
The sewage pump RHEINSTROM M is a self-priming diaphragm pump with bronze housing. Even bigger solids can be conveyed without damaging the pump because of the lip valves which have been installed. The self-locking valves make the pump non-reactive, i.e. it can be mounted to the side standing, hanging or sideways.Technical data:Output: 20 l / minHead: 8 mSuction height: 5 mSuction and pressure connection: 1 ½"Connection: 38 mm hoseWeight: 12 kg.
Oil-change kit OCK1 for mobile use made by renowned pump manufacturer MARCO:Self-priming gear pump UP3/OIL for pumping oil and other liquids.Brass pump body with bronze gears.Comes with 2 hose nozzles (12mm), hose clamps, suction tubes, and an adaptor for the tube.Dimensions L x W x H: 138mm x 108mm x 89mmCapacity (suction pipe/hose diameter 6/8/13mm): 0.3/1/5.5 l/min.With the included suction tubing set, old oil can be removed comfortably through the dipstick hole in the engine block.Ready for attachment with cable and battery clamps, two tubes (6mm und 8mm) with fittings and matching hose nozzles.The pump kit is also available as model OCK1-R with an integrated switch. This reversible UP3/OIL-R pump may be used for filling and draining.Dimensions L x W x H: 180mm x 108mm x 89mm
Extremely robust hand pump for pumping almost all liquids, even hot ones. The pump is well suited as an oil change and diesel pump. The pumps are not self-priming!The housing is completely made of cast iron and then varnished. The wings and valves are made of brass. The handle of the pump is made of wood (in the case of article 4626-010 the handle is made of varnished cast iron).On both sides there is an inch BSP female thread.Available with pump body made entirely of bronze on request.
Heavy duty gear pump. Ideal for oil change and transport of liquids of high viscosity.Self priming up to 1,5 m, not dry self priming.Weight 2,2 kg.With smart touch panel, allows reversing the pump for filling and draining.
Strong oil pump made entirely of brass.Typ A: intended for hose attachment with two mounting plates.Typ B: with thread M16 x 1,5.
Electric fuel pump that can be used to bring fuel to a stove if the primary tank is below the level of the fuel regulator and the installation of a day tank is not possible.This membrane pressure pump with electrically regulated electromagnetic works is maintenance-free and nearly wear-free.Data:- Dimensions: 73 x 128 mm,- Output: 120 l/h,- Pressure lift: 0.25 bar (max. 2,5 m),- Suction lift: -0.10 bar (max. 1,0 m),- Attachement fittings for hose 8 mm on both sides.
Ideal pump for changing the oil on board. The sturdy housing, transparent for checking the oil level, conceals a powerful vacuum pump.A few strokes generate a strong vacuum and allow oil to be sucked out of the engine via a plastic hose through the engine's dipstick opening. A shut-off function prevents the tank from overflowing.The device is completely maintenance-free and is supplied with 2 suction hoses D: 4.8 and D: 6.4 mm, length 1.2 m and a 1.0 m extension hose.
Self-priming small feed pump with bronze gears, particularly suitable for pumping diesel (day tank), low-viscosity oils, petroleum and antifreeze. Nickel-plated brass pump housing, stainless steel shaft. Suction height 1.5 m. Self-priming (not dry self-priming).Connections 3/8" internal thread, with hose nozzles for 14 mm hose.Comes with strainer.Also available as model MARCO UP3-S with integrated on/off switch or as transportable feed pump set MARCO UP3-CK. See under similar products.
Accessory for MARCO oil-change gear pumps:The plastic oil-change suction tubes allow a simple vacuum for sucking old oil through the dipstick opening in the engine block.Included: set with two tubes, L = 80cm.Diameter D = 6mm and 8mm.
Made from oil-resistant plastic, pump cylinder of brass. Comes with 2 hoses. Dimensions: 32 mm x 200 mm. Discharge: 0.1 l/pump.
Oil pump / oil change pump for fixed installation in the engine room or flexible operation. Made entirely of brass.Supplied with two mounting clamps and copper suction pipe (diameter = 6 mm, length = 370 mm).On the suction side: 1/4" internal thread and 1/2" external thread.Dimensions: Diameter = 29 mm, length = 200 mm.Flow rate: 0.05 l/stroke.Available in brass (Ms) or chrome-plated (Cr).Please note that a hose cover for the 1/2" external thread is not included in the scope of delivery.
A patented intake valve eases the filling of various liquids, for example water, diesel, or gas.The liquid must only be higher than the container being filled, no more sucking with the mouth necessary.Comes with a 2m hose.
The all-purpose manual pump RHP500UV serves for emptying or filling-up with fluids, which do not affect aluminium or brass. Features: universally deployable, casing made of aluminium, smooth-running due to a special slip ring, displaced volume 555 ml, weight 576 g. A nozzle tube with lenght 200 mm and an inside diameter of 10 mm is part of the shipment.
Self-priming (up to 1 m) gear pump for pumping oil and other liquids.Brass pump body with bronze gears.Supplied with two hose nozzles (12 mm), hose clamps and an adapter for plastic pipe (for suctioning used oil through the opening of the dipstick).With the suction pipe set, available separately as an accessory, used oil can be conveniently extracted through the dipstick opening on the engine block when changing the oil.Dimensions: D = 65, L = 140 mm, weight 1.4 kg.Capacity (with suction pipe 6/8/14mm): 20/60/330l/hType UP3/OIL-R is equipped with an integrated changeover switch that enables switching from emptying to filling.Also available as mobile complete kit OCK1 for oil pumping - see similar articles.
Portable transfer pump set type MARCO CK for mobile use.Complete with metal carrying case with plastic handle.Integrated "on-off" switch, cables with fuse and battery clamps.Self-priming electric pump type MARCO UP3, with bronze gears for transfer of various liquids.Main applications: transfer of diesel fuel (day tank), water, antifreeze and oils of low viscosity.Ports with brass connection for 3/8" inner tubing, with hose connectors for 14mm hose. Self priming 1,5 m.Comes with transparent plastic filter.
Small MARCO UP3-S feed pump with bronze gears and integrated, practical on/off switch. Suitable for pumping diesel (day tank), low-viscosity oils, petroleum and antifreeze. Delivery rate 15 litres per minute.Connections 3/8" internal thread, with hose nozzles for 14 mm hose.Comes with strainer.Also available as model MARCO UP3 without switch or as transportable feed pump set MARCO UP3-CK. See under similar products.
Simple jerrycan lift pump – industrial type. Operates on the siphon principle and allows easy, clean transfer of liquids from jerrycans or other containers. By briefly priming the liquid flow is initiated; the hydrostatic height difference then maintains the flow automatically. Hand bulb with vent screw to regulate the liquid flow. The suction tube is 40 cm long and has an internal diameter of 1/2 inches.· Flow rate: approx. 6.7 l/min· Hose diameter: ½″ (≈ 13 mm)· Suction tube: length approx. 40 cm· Total length: approx. 514 mm· Weight: approx. 50 g· Material: polyethylene· Colour: red bulb with transparent suction tube· Application: for petrol, diesel, kerosene (paraffin), water and comparable liquids
The MARCO UPE pumps are electronically controlled freshwater gear pumps designed for pressurized onboard water systems. They deliver constant water pressure without pulsation, operate quietly, save space, and are suitable for multiple outlets.The MARCO UPE pumps are self-priming gear pumps with electronic speed control and smooth, gradual start-up. Their speed automatically adjusts to the water demand, eliminating pressure fluctuations and pulsation in the system. An accumulator tank is only required when using rigid or very short pipes or solenoid valves.The pump housings are made of nickel-plated brass, and the spindles are stainless steel. The durable PEEK gears ensure high pressure, quiet operation, and excellent temperature resistance. Integrated non-return valves are included as standard. The pumps support both 12 V and 24 V operation. Connections are BSP female threads, and each pump is supplied with matching stainless-steel hose tails.The electronic control enables soft start and stop, reducing power consumption and water waste while significantly extending component life — up to three times longer than comparable models. The electronic system constantly monitors pressure, current, and voltage, provides protection against short circuits and overvoltage, and automatically stops the pumps when the tank is empty.These pumps run very quietly, require minimal space, and ensure reliable water supply on board.Models:· Type UP2/E: for max. 2 outlets, without pre-filter· Type UP3/E, UP6/E, UP12/E: for max. 3 outlets, with pre-filter· Type UP14/E: for max. 3 outlets, with pre-filter and PCS control panelKey Advantages at a Glance:· Electronic speed control, adjusts to water demand· Smooth, gradual start and stop· No pressure fluctuations, no pulsation· Self-priming (not dry self-priming)· No accumulator tank required except with rigid/short pipes or solenoid valves· PEEK gears: high pressure, quiet running, temperature resistant· Integrated non-return valves· Electronic monitoring of pressure, current, voltage· Protection against short circuit and overvoltage· Automatic shut-off when tank is empty· Multi-voltage: 12 V / 24 V· BSP female thread connections, incl. stainless-steel hose tails· Very quiet operation· Robust materials: nickel-plated brass, stainless steel
This self-priming bilge and deck wash pump is suitable for delivering sea water. It is completely made of bronze and stainless steel. Due to its hard-wearing industrial motor a longlasting and reliable operation is guaranteed. Before it is run for the first time it has to be filled with water. Furthermore it is advisable to install a socket safety valve or a foot operated valve into the suction pipe. The pump is non-reactive to sand (particle size up to 2 mm). The model 4 E is totally maintenance-free due to the use of a freely running impeller wheel and a very modern axial face seal. The max. operating time is 1 – 2 hoursTechnical dataOutput:50 l/minHeight pumped: 13 mSuction lift: 3 mAttachment: 3/4" BSP with inner threadsWeight: 7 kg
Repair kit #0350095 for the RHEINSTROM diaphragm pump M50 and M50E.The set consists of the pump membrane, a large seal and three valve flaps made from plastic.
The MARPOL Convention prohibits the discharge of oily wastewater into the sea. This filter removes the oily substances from the pumped bilge water by a patented filter system, so that the bilge water can be pumped out almost without oil residues and the water pollution is minimized.The filter is installed behind the bilge pump and in front of the ship's passage. It is suitable for oil residues, large dirt must be removed from the bilge before.Supplied with a stainless steel wall mounting plate.Replacement filter cartridges are available, annual replacement is recommended.LLOYD'S REGISTER Type Approved.
An exceptionally practical tool for removing impellers without damaging the pump housing.Body and jaws of aluminum, shaft of stainless steel.Dimensions, approx. 140 x 165 mm (W x H). Weight, 450 g.
Original JABSCO impeller for installation on most cooling water bilge pumps and universal pumps.To keep motors and pumps running smoothly, choosing the right impeller is critical. In addition to the hub mount and size, the material of the impeller should match its application:Neoprene is the most commonly used material for impellers and is suitable wherever only small amounts of oil or diesel fuel are present. Neoprene impellers are therefore suitable for engine cooling and for salt or fresh water pumping.Nitrile is oil resistant and can also be used for heavily polluted water. Impellers made of nitrile are therefore suitable for bilge and bilge pumps.The impellers are usually supplied with a matching paper cover gasket.Other JABSCO impellers and spare parts are also available at short notice on request.To see the matching image for the impeller, simply click on the part number in the table below.
We deliver a lot of spare parts for the WHALE GUSHER 10 bilge pump.
Accessory for bilge water filter WAVESTREAM.
We deliver a lot of spare parts for the WHALE GUSHER TITAN bilge pump.
Contents of service kit AK1550:MembraneValve flapVentMounting screws.Clampingring - kit AS1562 consists of clamping ring and screws.The service kit "pump head" (AK2050) holds the spare parts for the pump head (please check "Downloads & Information").
Deckring without lid for WHALE-pump MK5 (BP0535) for deck- or bulkhead mounting.Manufactured from white, UV-stabilised plastic.
We deliver a lot of spareparts for the WHALE GUSHER URCHIN bilge pump.
Accessories for foot pump WHALE GUSHER MKIII.
Replacement filter AK1319 for WHALE pressure water pumps of the WATERMASTER and UNIVERSAL types. For 15 mm WHALE QUICK CONNECT system.Technical featuresDesign: coarse filterConnection: 15 mm Quick ConnectCover: transparent cover for visual inspection; cover can be removed for cleaningWHALE No.: AK1319For UNIVERSAL models: UF0812, UF0815, UF1212, UF1214, UF1215, UF1225, UF1815, UF1825, UF2014, UF2015, UF8015, UF8025For WATERMASTER models: FW0814, FW0814B, FW1214, FW1214B, FW1215, FW1215B, FW1225, FW1225B, FT0814, FT0814B, FT1214, FT1214B
The Italian FINNORD group produces impellers in OEM quality for different manufacturers of pumps and offers a wide assortment of replacement impellers under the name CEF at reasonable prices.Here we present a selection of popular impellers made from neoprene and nitrile rubber.Usualy shipping complete with matching paper cover gaskets. To see the matching image for the impeller, simply click on the part number in the table below.Other sizes are available.
Spare parts kit (seals) for the CLASSIC galley pump (item no. 4613-014/-514).The CLASSIC spare parts kit (4613-100) is supplied with a nitrile seal only, as it has been found that if the pump is not used regularly, the pump leather can stick to the pump body due to drying out.Older pumps (built before 2011) also require the conversion kit (4613-101), which consists of a screw-on brass pump base valve and a threaded washer.
Plastic hose nozzle with union nut for 1/2" thread with 13 mm hose connection. For SHURFLO AQUAKING Pumpen.Available in straight or angled form.
Impeller of special nitril rubber. Original spare part for UP1, UP1-M and UP1/AC MARCO Pumps.Dimensions hight x Ø: 22 x 51.5 mm.Bore Ø: 8 mm.
Accessory for PLASTIMO bilge pump art-no. 1768-038 and 1768-039.
Accessory for JABSCO impellers: JABSCO impeller grease, 2,5 ml tube.
This electronic level switch does not require any mechanics or moving parts. Two field sensors ensure functional switching on and off of the connected pump. The switch turns on at 51 mm water level and turns off at 13 mm water level. The automatic sensor type BE9006 switches with an automatic 30 seconds switch-off delay. This delay allows water to be pumped out even below the switching level of 13 mm. The test function can be used to check the function of the pump after installation.Voltage: 12 V / 24 V.Max. switch current: 20 A.Residual current: 0,008 A.
RULE Model No. 35A: This proven and robust floating switch has a high switching power (240 VA) and works for pumps with high initial current. The plastic housing is sonic welded and thus the switch offers a high working security. For 12 - 32 V. Switching capacity: 168 VA.
Bilge pump control panel for optional switching of the bilge pump via a float switch or by manual switching. The rocker switch offers three switching options "automatic / off / manual".With two LED indicators for operation control and alarm. Protection is provided by an integrated thermal circuit breaker. Two versions are available: BPA202: For on-board voltage 12 and 24 volts. Without acoustic alarm.BPA203: For on-board voltage 12 or 24 volts. With acoustic alarm buzzer that can be quit via a pushbutton.
Pump switch without moving parts or delicate sensors.Switching power 240 VA.Switch function is triggered by air pressure.No electric installation underwater. Includes:Plastic measuring bell, 3 m air hose (diameter = 8 mm),Switch unit of plastic.Switch range 55 mm - 25 mm of water depht.Switch unit dimensions: 153 x 75 x 45 mm.Working voltage: 12 or 24 V.
Robust bilge switch with high switching capacity for powerful pumps. Very reliable switching due to a spring-loaded microswitch. Suitable for 12 volts and 24 volts. The switching capacity is maximum 168 VA (14A at 12V, 7A at 24V).The switch turns the pump on at a water level of 51mm and off at a water level of 19mm.
The floating switch RULE-A-MATIC PLUS 40 allows the automatic switching of a bilgepump.The switch is encapsulated securely in a plastic housing and protected against damage and dirt.Housing L x W x H: 120 x 65 x 70 mm.For 12 - 32 V.Switching capacity: 240 VA max. 20 amps with 12 V.Also available with acoustic alert (please check "Suitable items" below).
The floating switch RULE-A-MATIC-PLUS allows the automatic switching of a bilgepump and the release of the optical/auditory (85 dbA) signal. The switch is encapsulated securely in a plastic housing and protected against damage and dirt. The floating axis is lead out of the housing and allows the simple functioning of the switch. Housing: L x W x H: 120 x 65 x 70 mm. Signal 47 mm.Switching capacity: 240 VA (max. 20 amps with 12 V).
RULE Model No. 37A: This proven and robust floating switch has a high switching power (240 VA) and works for pumps with high initial current. The plastic housing is ultrasonic welded and thus the switch offers a high working security. For 12 - 32 V. Switching capacity: 240 VA.
Compact automatic switch for many installation possibilities, even on sloping surfaces with an angle of up to 24°. The switch works reliably and switches on as soon as the water in the bilge reaches a height of about 5 cm. The cover provides extra protection for the float switch, for example against dirt and coarse parts.Housing L x W x H: 133 x 98 x 73 mm. For: 12 - 24 V. Switching capacity: 120 VA max. 12 amps with 12 V.
Switch panel for automatic bilge pump. With sound and light alarm when pump is running automtically.With toggle switch, positions: "automatic/off/manual". With control lights and fuse 16 A/12 V. For 12 volt systems.
Switch panel, made of black plastic, for automatic bilge pump. With switch, positions: "auto / off / manual". With control lights and fuse 16A/12V or 8A/24V.For onboard systems of 12 or 24 volts.
Brand name three-way switch for bilge pumps with high switching capacity but without a fuse holder. Black coloured stainless steel panel.For on-board voltage of 12 Volt and 24 Volt. For manual pumping the switch has to be pressed from the OFF position to the right (push-button function).
For electric impeller pumps.Protects the pump against damage by dry run.The switch is installed on the sucction side of the pump. Cuts the power supply when the pressure drops, caused by a lack of water.Connected to the sucction tube by 1/4" BSP.
The MARCO PCS control panel allows the electronic pump to be switched on and off and monitored.Functions:On / Off,monitoring whether the pump is runningReset (if the pump has failed e.g. due totoo little liquid or overload),monitoring whether there is still enough liquid to pump.The control panel can be built in (a circular hole with a diameter of 70 mm is required), or screwed on with the housing.The control panel is connected to the pump by RJ11/6 telephone cable.Suitable for 12 and 24 volts. IP protection class 65. Dimensions L x W x H: 80 x 80 x 46 mm.
