Go to homepage
€0.00*
Jobs
Catalogue
Quick order

Vacuum switch for impeller pumps

1828*01 Trockenlauf-Schutzschalter für Impellerpumpe

€59.90*

€59.90*

Prices incl. VAT plus shipping costs

height (mm)
Ø (mm)
Stk

For electric impeller pumps.
Protects the pump against damage by dry run.
The switch is installed on the sucction side of the pump. Cuts the power supply when the pressure drops, caused by a lack of water.
Connected to the sucction tube by 1/4" BSP.

Show article


Downloads

Downloads

Questions about the product?

More products from the category Spare parts & accessories for pumps

Accessories for Bilge pump WHALE GUSHER TITAN
Accessories for Bilge pump WHALE GUSHER TITAN
We deliver a lot of spare parts for the WHALE GUSHER TITAN bilge pump.

From €61.50 *
Details
Accessories for WHALE GUSHER 30
Accessories for WHALE GUSHER 30
We deliver a lot of spare parts for the WHALE GUSHER 30 bilge pump.

From €98.50 *
Details
Accessories for WHALE GUSHER URCHIN
Accessories for WHALE GUSHER URCHIN
We deliver a lot of spareparts for the WHALE GUSHER URCHIN bilge pump.

From €39.90 *
Details
Belowdeck conversion set for WHALE GUSHER 30
Belowdeck conversion set for WHALE GUSHER 30
Deckplate and bridge for WHALE-pump Gusher 30, for deck or bulkhead mounting. Provides a neat cover over manual bilgepumps. Manufactured from aluminium cast. Snap-shut lid remains closed when pump is not in use.

€149.00 *
Details
Bilge water filter (oil strainer) WAVESTREAM
Bilge water filter (oil strainer) WAVESTREAM
The MARPOL Convention prohibits the discharge of oily wastewater into the sea. This filter removes the oily substances from the pumped bilge water by a patented filter system, so that the bilge water can be pumped out almost without oil residues and the water pollution is minimized.The filter is installed behind the bilge pump and in front of the ship's passage. It is suitable for oil residues, large dirt must be removed from the bilge before.Supplied with a stainless steel wall mounting plate.Replacement filter cartridges are available, annual replacement is recommended.LLOYD'S REGISTER Type Approved.

From €179.00 *
Details
Clamping piece for hand bilge pump
Clamping piece for hand bilge pump
Holding brackets, fit our brass hand bilge pump.Stainless steel.

€29.00 *
Details
Deck-/bulkhead plate for HENDERSON / WHALE MK5
Deck-/bulkhead plate for HENDERSON / WHALE MK5
Deckplate for HENDERSON/WHALE pump MK5 for deck or bulkhead mounting. Provides a neat cover over manual bilgepumps. Manufactured from UV stabilised plasic, will not fade or discolor. Snap-shut lid remains closed when pump is not in use.

€79.00 *
Details
Deck/-bulkheadplate for WHALE MK5-Pump
Deck/-bulkheadplate for WHALE MK5-Pump
Deckring without lid for WHALE-pump MK5 (BP0535) for deck- or bulkhead mounting.Manufactured from white, UV-stabilised plastic.

€82.00 *
Details
Deck/bulkhead plate for WHALE-pumps
Deck/bulkhead plate for WHALE-pumps
Deckplate for WHALEpumps for deck or bulkhead mounting. Provides a neat cover over manual bilgepumps. Manufactured from UV stabilised plasic, will not fade or discolor. Snap-shut lid remains closed when pump is not in use.Article-no. 1860-110 (DP8904) fits for Gusher 10, Urchin, Titan.

€49.90 *
Details
Deck/bulkhead plate for WHALE-pumps cast aluminium
Deck/bulkhead plate for WHALE-pumps cast aluminium
Deckplate for WHALE-pumps for deck or bulkhead mounting. Provides a neat cover over manual bilgepumps. Manufactured from aluminium cast. Snap-shut lid remains closed when pump is not in use. 1860-111 (DP3804) fits for Gusher 10 and 30 or Gusher Urchin.

€119.00 *
Details
Filter cartridge for WAVESTREAM bilgewater filters
Filter cartridge for WAVESTREAM bilgewater filters
Accessory for bilge water filter WAVESTREAM.

From €39.90 *
Details
Gaiter-Kit for WHALE/HENDERSON deckplates
Gaiter-Kit for WHALE/HENDERSON deckplates
Service kit for WHALE/HENDERSON deckplates suitable for underdeck models Gusher 30 and 10, Titan, Urchin, Mk5The kit includes a gaiter (diameter 108mm) and an O-ring.

€36.90 *
Details
Grease for impellers JABSCO
Grease for impellers JABSCO
Accessory for JABSCO impellers: JABSCO impeller grease, 2,5 ml tube.

€3.90 *
Details
Impeller
Impeller
The Italian FINNORD group produces impellers in OEM quality for different manufacturers of pumps and offers a wide assortment of replacement impellers under the name CEF at reasonable prices.Here we present a selection of popular impellers made from neoprene and nitrile rubber.Usualy shipping complete with matching paper cover gaskets. To see the matching image for the impeller, simply click on the part number in the table below.Other sizes are available.

From €18.90 *
Details
Impeller for impellerpump MARCO UP1
Impeller for impellerpump MARCO UP1
Impeller of special nitril rubber. Original spare part for UP1, UP1-M and UP1/AC MARCO Pumps.Dimensions hight x Ø: 22 x 51.5 mm.Bore Ø: 8 mm.

€32.90 *
Details
Impeller for impellerpump MARCO UP1-J
Impeller for impellerpump MARCO UP1-J
Impeller IMP2 of special nitril rubber. Original spare part for UP1-J and UP1-JR MARCO pumps.Dimensions hight x Ø: 22 x 40.5 mm.Bore Ø: 8 mm.

€32.90 *
Details
Impeller-kit JABSCO 6303-0003K
Impeller-kit JABSCO 6303-0003K
Spare impeller for JABSCO pumps.

From €34.90 *
Details
JABSCO Impeller
JABSCO Impeller
Original JABSCO impeller for installation on most cooling water bilge pumps and universal pumps.To keep motors and pumps running smoothly, choosing the right impeller is critical. In addition to the hub mount and size, the material of the impeller should match its application:Neoprene is the most commonly used material for impellers and is suitable wherever only small amounts of oil or diesel fuel are present. Neoprene impellers are therefore suitable for engine cooling and for salt or fresh water pumping.Nitrile is oil resistant and can also be used for heavily polluted water. Impellers made of nitrile are therefore suitable for bilge and bilge pumps.The impellers are usually supplied with a matching paper cover gasket.Other JABSCO impellers and spare parts are also available at short notice on request.To see the matching image for the impeller, simply click on the part number in the table below.

From €37.00 *
Details
JOHNSON impellers
JOHNSON impellers
Original long-lived SPX/JOHNSON brand neoprene and Nitrile rubber impeller. Usually the impellers come with matching cover gaskets of paper. To see the matching image for the impeller, simply click on the part number in the table below.Impellers made of oil-resistant nitrile rubber have a high resistance to oils, greases and hydrocarbons, they have good aging properties and low abrasion. Nitrile impellers are used, for example, for bilge pumps when the water is heavily contaminated by oil or diesel.MC97/EPDM and neoprene impellers are used for engine cooling and fresh or salt water pumping. Neoprene is the most commonly used material and is suitable wherever very small amounts of oil or diesel fuel are present.

From €27.91 *
Details
Outlet elbows for diaphragm pump PLASTIMO 11722
Outlet elbows for diaphragm pump PLASTIMO 11722
Outlet elbows for the diaphragm pump PLASTIMO model 11722.They are screwed and fitted with an O-ring for perfect water tightness and added safety (quick release facility). For a tube diameter of 38mm.

€17.90 *
Details
Repair kit for RHEINSTROM diaphragm pump M50 & M50E
Repair kit for RHEINSTROM diaphragm pump M50 & M50E
Repair kit #0350095 for the RHEINSTROM diaphragm pump M50 and M50E.The set consists of the pump membrane, a large seal and three valve flaps made from plastic.

€115.00 *
Details
Service kit for galley pump WELLINGTON
Service kit for galley pump WELLINGTON
Spares for FYNSPRAY galley pump WELLINGTON.Please check if your older pump has got a piston seal of leather or a newer pump one of rubber!

From €19.00 *
Details
Service kit for hand bilge pump (before 2012)
Service kit for hand bilge pump (before 2012)
Accessories for brass hand bilge pump, manufactured before 2012.

€19.90 *
Details
Service kit for hand bilge pump (from 2012)
Service kit for hand bilge pump (from 2012)
Accessories for brass hand bilge pump.

€17.90 *
Details
Service kit for oil drain pump
Service kit for oil drain pump
Accessories for oil drain pump.

€16.51 *
Details
Service kit for WHALE GULPER waste pump
Service kit for WHALE GULPER waste pump
Accessory for waste pump WHALE GULPER.

€64.00 *
Details
Service kit for WHLALE GULPER 220/320
Service kit for WHLALE GULPER 220/320
Contents of service kit AK1550:MembraneValve flapVentMounting screws.Clampingring - kit AS1562 consists of clamping ring and screws.The service kit "pump head" (AK2050) holds the spare parts for the pump head (please check "Downloads & Information").

From €53.00 *
Details
Service kit for WHLALE GUSHER 25
Service kit for WHLALE GUSHER 25
This service kit fits for WHALE GUSHER 25 pumps which are produced before 1989.

€174.00 *
Details
Service-kit for CLASSIC galley pump
Service-kit for CLASSIC galley pump
Spare parts kit (seals) for the CLASSIC galley pump (item no. 4613-014/-514).The CLASSIC spare parts kit (4613-100) is supplied with a nitrile seal only, as it has been found that if the pump is not used regularly, the pump leather can stick to the pump body due to drying out.Older pumps (built before 2011) also require the conversion kit (4613-101), which consists of a screw-on brass pump base valve and a threaded washer.

From €29.00 *
Details
Service-kit for foot pump BABY WHALE AK4610
Service-kit for foot pump BABY WHALE AK4610
Accessories for foot pump WHALE BABY.

€38.90 *
Details
Service-kit for HENDERSON/WHALE COMPACT 50
Service-kit for HENDERSON/WHALE COMPACT 50
Accessories for bilge pump HENDERSON/WHALE COMPACT 50.

€59.90 *
Details
Service-kit for MK5 HENDERSON/WHALE
Service-kit for MK5 HENDERSON/WHALE
Spares for diaphragm pump HENDERSON/WHALE MK5.

€68.50 *
Details
Servicekit 921 bilge and waste pump RM
Servicekit 921 bilge and waste pump RM
Spareparts for the bilge- and wastewater pump Raske & van der Meyde. The service kit 921 includes: Nr. 310.22* membrane Nr. 911* valve set Nr. 912* O-ring

€39.00 *
Details
Servicekit for foot pump TIPTOE WHALE AK1304
Servicekit for foot pump TIPTOE WHALE AK1304
Accessories for foot pump WHALE TIPTOE.

€36.90 *
Details
Servie kit vor galley pump NELSON
Servie kit vor galley pump NELSON
Spares kit for FYNSPRAY galley pumps NELSON.

€27.00 *
Details
SHURFLO hose nozzle
SHURFLO hose nozzle
Plastic hose nozzle with union nut for 1/2" thread with 13 mm hose connection. For SHURFLO AQUAKING Pumpen.Available in straight or angled form.

From €10.00 *
Details
Spare exenter for electric diaphragm pump EVS
Spare exenter for electric diaphragm pump EVS
Accessories for electric diaphragm pump EVS.

€72.00 *
Details
Spare filter kit for MARCO pumps UPE
Spare filter kit for MARCO pumps UPE
Filter made of transparent nylon, which protects gear and impeller pumps from small particle contamination. The stainless steel filter net (AISI 304) has a mesh size of 0.5 mm, the enclosed fittings (two hose nozzles and a double nipple fitting) are made of chrome-plated brass.The filter is suitable for bilge and fresh water pumps and can be connected directly to MARCO UPE pumps with the enclosed double nipple. With the enclosed hose nozzles, it can also be integrated into a (hose) line system as an inline filter. The filter can be easily opened for cleaning and can be checked easily through the transparent nylon housing.

From €39.00 *
Details
Spare handle for HENDERSON/WHALE MK5 pumps
Spare handle for HENDERSON/WHALE MK5 pumps
Spare handle for HENDERSON/WHALE MK5 pumps.Inox tube with black plasic knob.

€59.00 *
Details
Spare handle for WHALE GUSHER & TITAN bilge pumps
Spare handle for WHALE GUSHER & TITAN bilge pumps
Spare handle for WHALE GUSHER 10 and WHALE TITAN bilge pump.Inox tube with black plasic knob.

€62.90 *
Details
Spare kits for FYNSPRAY AUCKLAND / DUNEDIN pumps
Spare kits for FYNSPRAY AUCKLAND / DUNEDIN pumps
Spares for FYNSPRAY galley pumps AUCKLAND or DUNEDIN.

€27.00 *
Details
Spare parts for bilge pump PLASTIMO 11722 / 11723
Spare parts for bilge pump PLASTIMO 11722 / 11723
Accessory for PLASTIMO bilge pump art-no. 1768-038 and 1768-039.

From €17.90 *
Details
Spare parts for bilge pump PLASTIMO 12760
Spare parts for bilge pump PLASTIMO 12760
Accessory for PLASTIMO bilge pump type 12760 (our Art-No. 1768-025).

From €32.90 *
Details
Spare parts for foot pump GUSHER MK3 WHALE AK0553
Spare parts for foot pump GUSHER MK3 WHALE AK0553
Accessories for foot pump WHALE GUSHER MKIII.

From €32.90 *
Details
Spare parts for WHALE GUSHER 10
Spare parts for WHALE GUSHER 10
We deliver a lot of spare parts for the WHALE GUSHER 10 bilge pump.

From €72.90 *
Details
Spare piston and seal for galley pumps FYNSPRAY
Spare piston and seal for galley pumps FYNSPRAY
Spare piston forFYNSPRAY galley pumps.Piston ao brass and seal of rubber.

€19.00 *
Details
Spares for iron diaphragm pump
Spares for iron diaphragm pump
These standard spare parts fit to our cast iron diaphragm pump TII (Art-Nr. 1878-001).

From €49.00 *
Details
Tool for removing impellers JABSCO
Tool for removing impellers JABSCO
An exceptionally practical tool for removing impellers without damaging the pump housing.Body and jaws of aluminum, shaft of stainless steel.Dimensions, approx. 140 x 165 mm (W x H). Weight, 450 g.

From €99.00 *
Details
Vacuum switch for impeller pumps
Vacuum switch for impeller pumps
For electric impeller pumps.Protects the pump against damage by dry run.The switch is installed on the sucction side of the pump. Cuts the power supply when the pressure drops, caused by a lack of water.Connected to the sucction tube by 1/4" BSP.

€59.90 *
Details

Zuletzt angesehene Artikel