Gaiter-Kit for WHALE/HENDERSON deckplates

Art. No.	WHALE No	Price (package)	Delivery time	Note list	Buy
1860-112	AS3725	€36.90* net: €31.01	In stock The item is in stock ready for shipping. The delivery time is approx. 1 to 3 working days.

Spare parts for WHALE GUSHER 10

We deliver a lot of spare parts for the WHALE GUSHER 10 bilge pump.

From €72.90 *

Details

Spare piston and seal for galley pumps FYNSPRAY

Spare piston forFYNSPRAY galley pumps.Piston ao brass and seal of rubber.

€19.00 *

Details

Spares for iron diaphragm pump

These standard spare parts fit to our cast iron diaphragm pump TII (Art-Nr. 1878-001).

From €49.00 *

Details

Tool for removing impellers JABSCO

An exceptionally practical tool for removing impellers without damaging the pump housing.Body and jaws of aluminum, shaft of stainless steel.Dimensions, approx. 140 x 165 mm (W x H). Weight, 450 g.

From €99.00 *

Details

Vacuum switch for impeller pumps

For electric impeller pumps.Protects the pump against damage by dry run.The switch is installed on the sucction side of the pump. Cuts the power supply when the pressure drops, caused by a lack of water.Connected to the sucction tube by 1/4" BSP.

€59.90 *

Details

Accessories for Bilge pump WHALE GUSHER TITAN

We deliver a lot of spare parts for the WHALE GUSHER TITAN bilge pump.

From €61.50 *

Details

Accessories for WHALE GUSHER 30

We deliver a lot of spare parts for the WHALE GUSHER 30 bilge pump.

From €98.50 *

Details

Accessories for WHALE GUSHER URCHIN

We deliver a lot of spareparts for the WHALE GUSHER URCHIN bilge pump.

From €39.90 *

Details

Belowdeck conversion set for WHALE GUSHER 30

Deckplate and bridge for WHALE-pump Gusher 30, for deck or bulkhead mounting. Provides a neat cover over manual bilgepumps. Manufactured from aluminium cast. Snap-shut lid remains closed when pump is not in use.

€149.00 *

Details

Bilge water filter (oil strainer) WAVESTREAM

The MARPOL Convention prohibits the discharge of oily wastewater into the sea. This filter removes the oily substances from the pumped bilge water by a patented filter system, so that the bilge water can be pumped out almost without oil residues and the water pollution is minimized.The filter is installed behind the bilge pump and in front of the ship's passage. It is suitable for oil residues, large dirt must be removed from the bilge before.Supplied with a stainless steel wall mounting plate.Replacement filter cartridges are available, annual replacement is recommended.LLOYD'S REGISTER Type Approved.

From €179.00 *

Details

Clamping piece for hand bilge pump

Holding brackets, fit our brass hand bilge pump.Stainless steel.

€29.00 *

Details

Deck-/bulkhead plate for HENDERSON / WHALE MK5

Deckplate for HENDERSON/WHALE pump MK5 for deck or bulkhead mounting. Provides a neat cover over manual bilgepumps. Manufactured from UV stabilised plasic, will not fade or discolor. Snap-shut lid remains closed when pump is not in use.

€79.00 *

Details

Deck/-bulkheadplate for WHALE MK5-Pump

Deckring without lid for WHALE-pump MK5 (BP0535) for deck- or bulkhead mounting.Manufactured from white, UV-stabilised plastic.

€82.00 *

Details

Deck/bulkhead plate for WHALE-pumps

Deckplate for WHALEpumps for deck or bulkhead mounting. Provides a neat cover over manual bilgepumps. Manufactured from UV stabilised plasic, will not fade or discolor. Snap-shut lid remains closed when pump is not in use.Article-no. 1860-110 (DP8904) fits for Gusher 10, Urchin, Titan.

€49.90 *

Details

Deck/bulkhead plate for WHALE-pumps cast aluminium

Deckplate for WHALE-pumps for deck or bulkhead mounting. Provides a neat cover over manual bilgepumps. Manufactured from aluminium cast. Snap-shut lid remains closed when pump is not in use. 1860-111 (DP3804) fits for Gusher 10 and 30 or Gusher Urchin.

€119.00 *

Details

Filter cartridge for WAVESTREAM bilgewater filters

Accessory for bilge water filter WAVESTREAM.

From €39.90 *

Details

Gaiter-Kit for WHALE/HENDERSON deckplates

Service kit for WHALE/HENDERSON deckplates suitable for underdeck models Gusher 30 and 10, Titan, Urchin, Mk5The kit includes a gaiter (diameter 108mm) and an O-ring.

€36.90 *

Details

Grease for impellers JABSCO

Accessory for JABSCO impellers: JABSCO impeller grease, 2,5 ml tube.

€3.90 *

Details

Impeller

The Italian FINNORD group produces impellers in OEM quality for different manufacturers of pumps and offers a wide assortment of replacement impellers under the name CEF at reasonable prices.Here we present a selection of popular impellers made from neoprene and nitrile rubber.Usualy shipping complete with matching paper cover gaskets. To see the matching image for the impeller, simply click on the part number in the table below.Other sizes are available.

From €18.90 *

Details

Impeller for impellerpump MARCO UP1

Impeller of special nitril rubber. Original spare part for UP1, UP1-M and UP1/AC MARCO Pumps.Dimensions hight x Ø: 22 x 51.5 mm.Bore Ø: 8 mm.

€32.90 *

Details

Impeller for impellerpump MARCO UP1-J

Impeller IMP2 of special nitril rubber. Original spare part for UP1-J and UP1-JR MARCO pumps.Dimensions hight x Ø: 22 x 40.5 mm.Bore Ø: 8 mm.

€32.90 *

Details

Impeller-kit JABSCO 6303-0003K

Spare impeller for JABSCO pumps.

From €34.90 *

Details

JABSCO Impeller

Original JABSCO impeller for installation on most cooling water bilge pumps and universal pumps.To keep motors and pumps running smoothly, choosing the right impeller is critical. In addition to the hub mount and size, the material of the impeller should match its application:Neoprene is the most commonly used material for impellers and is suitable wherever only small amounts of oil or diesel fuel are present. Neoprene impellers are therefore suitable for engine cooling and for salt or fresh water pumping.Nitrile is oil resistant and can also be used for heavily polluted water. Impellers made of nitrile are therefore suitable for bilge and bilge pumps.The impellers are usually supplied with a matching paper cover gasket.Other JABSCO impellers and spare parts are also available at short notice on request.To see the matching image for the impeller, simply click on the part number in the table below.

From €37.00 *

Details

JOHNSON impellers

Original long-lived SPX/JOHNSON brand neoprene and Nitrile rubber impeller. Usually the impellers come with matching cover gaskets of paper. To see the matching image for the impeller, simply click on the part number in the table below.Impellers made of oil-resistant nitrile rubber have a high resistance to oils, greases and hydrocarbons, they have good aging properties and low abrasion. Nitrile impellers are used, for example, for bilge pumps when the water is heavily contaminated by oil or diesel.MC97/EPDM and neoprene impellers are used for engine cooling and fresh or salt water pumping. Neoprene is the most commonly used material and is suitable wherever very small amounts of oil or diesel fuel are present.

From €27.91 *

Details

Outlet elbows for diaphragm pump PLASTIMO 11722

Outlet elbows for the diaphragm pump PLASTIMO model 11722.They are screwed and fitted with an O-ring for perfect water tightness and added safety (quick release facility). For a tube diameter of 38mm.

€17.90 *

Details

Repair kit for RHEINSTROM diaphragm pump M50 & M50E

Repair kit #0350095 for the RHEINSTROM diaphragm pump M50 and M50E.The set consists of the pump membrane, a large seal and three valve flaps made from plastic.

€115.00 *

Details

Service kit for galley pump WELLINGTON

Spares for FYNSPRAY galley pump WELLINGTON.Please check if your older pump has got a piston seal of leather or a newer pump one of rubber!

From €19.00 *

Details

Service kit for hand bilge pump (before 2012)

Accessories for brass hand bilge pump, manufactured before 2012.

€19.90 *

Details

Service kit for hand bilge pump (from 2012)

Accessories for brass hand bilge pump.

€17.90 *

Details

Service kit for oil drain pump

Accessories for oil drain pump.

€16.51 *

Details

Service kit for WHALE GULPER waste pump

Accessory for waste pump WHALE GULPER.

€64.00 *

Details

Service kit for WHLALE GULPER 220/320

Contents of service kit AK1550:MembraneValve flapVentMounting screws.Clampingring - kit AS1562 consists of clamping ring and screws.The service kit "pump head" (AK2050) holds the spare parts for the pump head (please check "Downloads & Information").

From €53.00 *

Details

Service kit for WHLALE GUSHER 25

This service kit fits for WHALE GUSHER 25 pumps which are produced before 1989.

€174.00 *

Details

Service-kit for CLASSIC galley pump

Spare parts kit (seals) for the CLASSIC galley pump (item no. 4613-014/-514).The CLASSIC spare parts kit (4613-100) is supplied with a nitrile seal only, as it has been found that if the pump is not used regularly, the pump leather can stick to the pump body due to drying out.Older pumps (built before 2011) also require the conversion kit (4613-101), which consists of a screw-on brass pump base valve and a threaded washer.

From €29.00 *

Details

Service-kit for foot pump BABY WHALE AK4610

Accessories for foot pump WHALE BABY.

€38.90 *

Details

Service-kit for HENDERSON/WHALE COMPACT 50

Accessories for bilge pump HENDERSON/WHALE COMPACT 50.

€59.90 *

Details

Service-kit for MK5 HENDERSON/WHALE

Spares for diaphragm pump HENDERSON/WHALE MK5.

€68.50 *

Details

Servicekit 921 bilge and waste pump RM

Spareparts for the bilge- and wastewater pump Raske & van der Meyde. The service kit 921 includes: Nr. 310.22* membrane Nr. 911* valve set Nr. 912* O-ring

€39.00 *

Details

Servicekit for foot pump TIPTOE WHALE AK1304

Accessories for foot pump WHALE TIPTOE.

€36.90 *

Details

Servie kit vor galley pump NELSON

Spares kit for FYNSPRAY galley pumps NELSON.

€27.00 *

Details

SHURFLO hose nozzle

Plastic hose nozzle with union nut for 1/2" thread with 13 mm hose connection. For SHURFLO AQUAKING Pumpen.Available in straight or angled form.

From €10.00 *

Details

Spare exenter for electric diaphragm pump EVS

Accessories for electric diaphragm pump EVS.

€72.00 *

Details

Spare filter kit for MARCO pumps UPE

Filter made of transparent nylon, which protects gear and impeller pumps from small particle contamination. The stainless steel filter net (AISI 304) has a mesh size of 0.5 mm, the enclosed fittings (two hose nozzles and a double nipple fitting) are made of chrome-plated brass.The filter is suitable for bilge and fresh water pumps and can be connected directly to MARCO UPE pumps with the enclosed double nipple. With the enclosed hose nozzles, it can also be integrated into a (hose) line system as an inline filter. The filter can be easily opened for cleaning and can be checked easily through the transparent nylon housing.

From €39.00 *

Details

Spare handle for HENDERSON/WHALE MK5 pumps

Spare handle for HENDERSON/WHALE MK5 pumps.Inox tube with black plasic knob.

€59.00 *

Details

Spare handle for WHALE GUSHER & TITAN bilge pumps

Spare handle for WHALE GUSHER 10 and WHALE TITAN bilge pump.Inox tube with black plasic knob.

€62.90 *

Details

Spare kits for FYNSPRAY AUCKLAND / DUNEDIN pumps

Spares for FYNSPRAY galley pumps AUCKLAND or DUNEDIN.

€27.00 *

Details

Spare parts for bilge pump PLASTIMO 11722 / 11723

Accessory for PLASTIMO bilge pump art-no. 1768-038 and 1768-039.

From €17.90 *

Details

Spare parts for bilge pump PLASTIMO 12760

Accessory for PLASTIMO bilge pump type 12760 (our Art-No. 1768-025).

From €32.90 *

Details

Spare parts for foot pump GUSHER MK3 WHALE AK0553

Accessories for foot pump WHALE GUSHER MKIII.

From €32.90 *

Details

Spare parts for WHALE GUSHER 10

We deliver a lot of spare parts for the WHALE GUSHER 10 bilge pump.

From €72.90 *

Details

Spare piston and seal for galley pumps FYNSPRAY

Spare piston forFYNSPRAY galley pumps.Piston ao brass and seal of rubber.

€19.00 *

Details

Spares for iron diaphragm pump

These standard spare parts fit to our cast iron diaphragm pump TII (Art-Nr. 1878-001).

From €49.00 *

Details

Tool for removing impellers JABSCO

An exceptionally practical tool for removing impellers without damaging the pump housing.Body and jaws of aluminum, shaft of stainless steel.Dimensions, approx. 140 x 165 mm (W x H). Weight, 450 g.

From €99.00 *

Details

Vacuum switch for impeller pumps

For electric impeller pumps.Protects the pump against damage by dry run.The switch is installed on the sucction side of the pump. Cuts the power supply when the pressure drops, caused by a lack of water.Connected to the sucction tube by 1/4" BSP.

€59.90 *

Details

Accessories for Bilge pump WHALE GUSHER TITAN

We deliver a lot of spare parts for the WHALE GUSHER TITAN bilge pump.

From €61.50 *

Details

Accessories for WHALE GUSHER 30

We deliver a lot of spare parts for the WHALE GUSHER 30 bilge pump.

From €98.50 *

Details

Accessories for WHALE GUSHER URCHIN

We deliver a lot of spareparts for the WHALE GUSHER URCHIN bilge pump.

From €39.90 *

Details

Belowdeck conversion set for WHALE GUSHER 30

Deckplate and bridge for WHALE-pump Gusher 30, for deck or bulkhead mounting. Provides a neat cover over manual bilgepumps. Manufactured from aluminium cast. Snap-shut lid remains closed when pump is not in use.

€149.00 *

Details

Bilge water filter (oil strainer) WAVESTREAM

The MARPOL Convention prohibits the discharge of oily wastewater into the sea. This filter removes the oily substances from the pumped bilge water by a patented filter system, so that the bilge water can be pumped out almost without oil residues and the water pollution is minimized.The filter is installed behind the bilge pump and in front of the ship's passage. It is suitable for oil residues, large dirt must be removed from the bilge before.Supplied with a stainless steel wall mounting plate.Replacement filter cartridges are available, annual replacement is recommended.LLOYD'S REGISTER Type Approved.

From €179.00 *

Details

Mon - Fri:	09 am - 06 pm
Sat:	09 am - 01 pm

Gaiter-Kit for WHALE/HENDERSON deckplates

Gaiter-Kit for WHALE/HENDERSON deckplates

Downloads

Description

Downloads