Exhaust gas, regulators, spares & accessories

Rotating stainless steel vent that can also be used as a gas vent for all opening types, protected against backdrafts and supports the correct draft of the chimney.The (folding) extraction fan runs on ball bearings and is propelled by the wind.The flange is made of a light DURAL-INOX alloy. Available is also a version 240 C with a square ground plate (330 x 330mm) for profiles of 200 x 200mm up to 250 x 250mm. The enclosed attachment bolts allow mounting on pipes of varying diameters.Output data based on 3 beaufort wind velocity (10 kn).

This flue pipes matches the REFLEKS heating system and other gas or coal stoves with matching exhaust outlets.Made of acid-proof stainless steel (wall depth 0.6 mm).Plugs together: slightly conical with pressed sleeve on one side.

The flue cap of the Danish fishermen.The cap offers the most safe adjustment and is exceptionally secure against down drafts.Fits the double-walled flue pipes.

By REFLEKS especially for their different stoves pre aligned oil metering valves by the swiss manufacturer TOBY.The oil metering valves are equipped with an attached safety valve with a fusible cut-out for the automatic cut-off when the stove is overheating above 100°C. Fitting tubing: copper tube with D = 8 mm;Inlet and overflow pipe: compression type fitting,Outlet: flare type fitting.The TOBY oil metering valve DVR 5 is a time-tested single compartment controller for oil stoves, that operates with the gasification technique. The controller serves to regulate the amount of oil flowing and thereby the heating output. At the same time it acts as the safety valve for the stove.Since the CC oil metering valves used by REFLEKS before 2012 are not produced any more, a change to the TOBY oil metering valve became necessary.

Thickness 0.6 mm, insulated with 10 mm of rock wool.Above all, at the lowest temperatures, double flue pipes are necessary outside, so that the draft through very cold pipes can be restricted.

The burner pots in REFLEKS oil-fired stoves are made of sheet steel, so they may need to be replaced after years of use.The burner pots are supplied complete with a welded inlet pipe and stainless steel flame guide rings. The small burner pots, models 66M and 71M, also include a stainless steel glow coil (catalyst) in the scope of delivery.For the larger burner pots, the catalysts must be ordered separately.We also carry replacement parts for REFLEKS stoves not listed here, such as burner rings, complete inner stoves, and heating coils.

Through-deck fitting with round, inclined deck plate.Made of stainless steel.Avaialable in various angles for adapting to the deck inclination.Fits the REFLEKS flue pipes.

Guard for flue pipes that are installed in close quaters.Avaiable in stainless steel, brass or copper plate.The risk of contact burns is minimized, but the warmth of the pipe can still be enjoyed.Matches REFLEKS flue pipes of 70 mm or 90 mm.The flue guard is attached to the flue pipe and fixed with two stainless steel brackets, which are included in the package.Distance from flue pipe, 15 mm.

Thin flue cap, type YACHT.The design of this cap ensures a very secure fit and a good draft.Rain-proof and very compact.The rounded edges keep lines from hooking on it.

Standard exhaust hoods REFLEKS.

Deck through hull with round deck plate, stainless steel. Suitable for our REFLEKS flue pipes.

Pipe socket with draft flap for draw regulation and performance improvement of REFLEKS stoves.The exhaust ventilation is installed directly over the stove and when used automatically guides air into the exhaust guide pipe.Recommended for long or problematic exhaust leads.Length 330 mm.

This flue pipes matches the REFLEKS heating system and other gas or coal stoves with matching exhaust outlets.Made of acid-proof stainless steel (wall depth 0.6 mm).Plugs together: slightly conical with pressed sleeve on one side.

This flue pipes matches the REFLEKS heating system and other gas or coal stoves with matching exhaust outlets.Made of acid-proof stainless steel (wall depth 0.6 mm).Plugs together: slightly conical with pressed sleeve on one side.

Closing cap, stainless steel. Suitable for all REFLEKS flue pipes.

Thickness 0.6 mm, insulated with 10 mm of rock wool.Above all, at the lowest temperatures, double flue pipes are necessary outside, so that the draft through very cold pipes can be restricted.

Base plate for all REFLEKS stoves.Very highly recommended for safe installation. Because of its high edge, it will collect leaked fuel.

Required for double-walled flue pipes, in order to mount an exhaust hood that fits the inner diameter.

Combustion chamber insert with catalytic converter function for retrofitting the 60 and 61 models.All new REFLEKS stoves, with the exception of the 60/61 models, are already equipped with these spirals.The grid-shaped catalytic converter is placed in the burner pot of the REFLEKS stoves and supports cleaner combustion of the fuel. Due to its open structure with a large surface area, it enables the post-combustion of unburned components and helps to reduce emissions and deposits.At high operating temperatures, the unburned hydrocarbons (HC) and carbon monoxide (CO) are oxidized. This reduces odors and visible smoke development. The heated grid structure also supports the post-combustion of fine soot particles. The result is cleaner flue gas and fewer deposits in the chimney.The metal grille stores heat and thus stabilizes the combustion process. This results in more even flame formation and improved combustion in partial load operation. The more complete conversion of the fuel means it is used more efficiently.

Small reflector plate for heat protection behind flue pipes.Plate stainless steel.Measurements:50cm high, 15cm wide.Available as flat or recessed version.The flat plate must be mounted with spacers or insulation behind, the recessed plate can be mounted directly on the wall.

DICKINSON deck sleeve made from stainless steel, fits DICKINSON stove pipes. delivery with inner ring (the inner ring can also be orderd seperatly). Matching covers (for when the pipe or hood is put below) are available. As a Dickinson importer and wholesaler, we carry just about every original spare part and accessory.

Stove pipe for DICKINSON stoves and ovens.Stainless steel.As a Dickinson importer and wholesaler, we carry just about every original spare part and accessory.

Exhaust hood for DICKINSON stove pipes.H - shaped, for difficult ventilation situations.Stainless steel.As a Dickinson importer and wholesaler, we carry just about every original spare part and accessory.

DICKINSON uses WALBRO pumps from the FRD series to reliably supply diesel ovens and stoves with diesel. They enable the safe operation of heating appliances, even under demanding installation conditions.Various models are available depending on the delivery head and climatic conditions:the standard pump FRD-2 (20-000) for simple installations and the more powerful heavy-duty versions FRD-3 (20-002A) and FRD-4 (20-002) with adjustable pressure regulator for longer delivery distances or use in very cold temperatures.

Exhaust hood for DICKINSON stove pipes.Rain-proof standard hood, made of stainless steel.As a Dickinson importer and wholesaler, we carry just about every original spare part and accessory.

Pipe elbow for DICKINSON stove pipes.Stainless steel.As a Dickinson importer and wholesaler, we carry just about every original spare part and accessory.

Small reflector plate for heat protection behind flue pipes.Plate stainless steel.Measurements:50cm high, 15cm wide.Available as flat or recessed version.The flat plate must be mounted with spacers or insulation behind, the recessed plate can be mounted directly on the wall.

A stainless steel flue pipe T-piece with integrated draught regulator. The draught regulator is used as the first or second piece of pipe from the top of the stove or oven. The draught regulator helps to reduce the draught in long chimneys and allows the user to operate the appliance at a lower fuel setting.The draught reduction is adjustable. For this purpose, the pendulum damper is adapted to the respective chimney installation via an adjustable counterweight.Recommended for all installations and especially for chimneys with a height of 6 feet or more.As a Dickinson general importer and specialist wholesaler, we stock almost all original spare parts and accessories. Parts not listed here are available on request.

As a Dickinson importer and wholesaler, we carry just about every original spare part and accessory.

Heater with which radiant heat from the exhaust pipe system is diverted to other rooms.Instead of a 550 mm stove pipe, HEATEX is used in the pipe system. It consists of a 550mm tube jacketed by a heat exchanger. On the back there is a flange with which DICKINSON pipes or flexible exhaust hoses are connected to the fan. When the fan is switched on, the heat is sucked in through the connecting line and distributed in the room.The scope of delivery includes the heat exchanger, the fan (12 or 24 volts) and a pipe angle.All parts are made of stainless steel.

We offer a suitable adapter so that the REFLEKS gas flue system can be used with DICKINSON ovens or stoves without any problems.Installation is very simple:The original flue gas connector is replaced by a REFLEKS adapter. This is attached with just two screws and can be replaced in just a few minutes. The REFLEKS pipes can then be fitted directly and securely.Under the following link, DICKINSON offers various interesting videos to assist with the maintenance, repair and installation of ovens and stoves:https://www.youtube.com/@DickinsonMarine-since1932As a Dickinson importer and wholesaler, we carry just about every original spare part and accessory.

As a Dickinson importer and wholesaler, we carry just about every original spare part and accessory.

Diesel heaters and stoves that burn fuel in a bowl burner are dependent on an uninterrupted, coordinated fuel supply to ensure that the flame does not go out or start to blacken.The task of the oil regulator is to constantly supply the correct amount of oil to the heater or stove.The adjustable oil regulator from DICKINSON regulates the correct oil supply to the burner bowl and ensures a safety shutdown via a float if the flame goes out unintentionally.It works without fault-prone electrics or electronics and is therefore particularly reliable. The regulator has a safety cut-out integrated into the control knob, which permanently interrupts the oil supply at temperatures above 75 °C.Dickinson offers a variety of interesting videos at the following link to help with the maintenance, repair and installation of stoves and ranges:https://www.youtube.com/@DickinsonMarine-since1932As a Dickinson importer and wholesaler, we carry just about every original spare part and accessory. 

Replacement fire grate for the DICKINSON NEWPORT solid fuel stove. Material: A4 stainless steelAfter several years of heating operation, the fire grate may need to be replaced.Original DICKINSON spare part.

Burner case made of stainless steel, for TAYLOR'S 079D.Is placed on the burner pot and fixed with a screw.Includes viewing window (frame, seal, glass, screws).Spare part for TAYLOR'S 079D diesel heaters.TAYLOR'S Code HTD5306Handbook Code 23Additional to the parts mentioned here, all important spare parts are available from stock.We can order other parts directly from the manufacturer.Please be so free and order the detailed explosion chart or the manual as a copy.

Small reflector plate for heat protection behind flue pipes.Plate stainless steel.Measurements:50cm high, 15cm wide.Available as flat or recessed version.The flat plate must be mounted with spacers or insulation behind, the recessed plate can be mounted directly on the wall.

The TAYLOR oil-heater is equipped with this safety feature.The temperature sensor shuts the fuel supply off, if the flame dies.Also intended for retrofitting older stoves.

Stainless steel cap to cover the deck passage, fits the diesel stove 079D.In addition to the accessories and spare parts listed here, we can supply other important parts from stock or order them for you at the factory.

The TAYLOR diesel stove is equipped with a flame safety valve. The thermosensor shuts off the oil supply via the magnetic valve if the flame stops burning. The thermosensor is also suitable for retrofitting older stoves.In addition to the accessories and spare parts listed here, we can supply other important parts from stock or order them for you at the factory.

All REFLEKS heating systems with a water circuit should be equipped with this shut-off valve.The KBB fire protection valve is a compact valve in a corrosion-resistant, non-flammable design that operates purely mechanically and does not require a power supply.The temperature sensor is connected to the valve via a permanently soldered capillary line.As soon as the temperature at the sensor exceeds the set value (90°), the oil supply to the stove is immediately interrupted by the valve.The valve remains closed until the reset button is pressed.The valve can also be triggered manually by pulling the reset button.The valve (supplied with connection material for 8 mm pipes, SR 8 mm cutting ring fitting on both sides) is installed in the oil supply line directly upstream of the regulator.The temperature sensor measures the flow hot water temperature near the heater. If the set temperature (90°C) is exceeded, the oil supply is shut off immediately.To connect the sensor to the heating pipework, use a copper T-piece with two G ½" male threaded pipe fittings (please order item no. 4292-100 separately). The vertical branch of the T-piece does not have direct access to the water circuit of the heating system, but is soldered onto the water-carrying pipe and serves to accommodate the temperature sensor.Care must be taken during installation to ensure that the capillary line is not kinked under any circumstances. Length of the sensor line 200 cm.

Deck flange for passing the exhaust duct through the deck. The flange fits the TAYLOR'S petroleum heater 079D. In addition to the accessories and spare parts listed here, we can supply other important parts from stock or order them for you at the factory.

Accessories for TAYLOR'S oil heater.Additional to the parts mentioned here, all important spare parts are available from stock.We can order other parts directly from the manufacturer.Please be so free and order the detailed explosion chart or the manual as a copy.

Straight stainless steel exhaust pipes for TAYLOR'S diesel stove 079D and for TAYLOR'S petroleum heater 079K.In addition to the accessories and spare parts listed here, we can supply other important parts from stock or order them for you at the factory.

Exhaust pipes with a 45° angle for TAYLOR'S diesel heater 079D and for TAYLORS petroleum heater 079K.In addition to the accessories and spare parts listed here, we can supply other important parts from stock or order them for you at the factory.

Exhaust hood for TAYLORS'S diesel stove 079K. The exhaust hood prevents wind and water from entering the exhaust pipe.In addition to the accessories and spare parts listed here, we can supply other important parts from stock or order them for you at the factory.

Rubber cap to lock the deck hull of TAYLOR'S petroleum heater 079K.In addition to the accessories and spare parts listed here, we can supply other important parts from stock or order them for you at the factory.

Deck flange for passing the exhaust duct through the deck. The flange fits the TAYLOR'S petroleum heater 079K.In addition to the accessories and spare parts listed here, we can supply other important parts from stock or order them for you at the factory.

Fuel filter for all TAYLOR'S appliances, replaces the former filter CTK1185.Installation in the fuel system between tank and burner to protect the sometimes sensitive burners from contaminated fuel.Filter element made of fine metal mesh.Spare part for:TAYLOR'S 028, 029, 030, 030L Kerosene cookers and stovesTAYLOR'S 079K Kerosene heatersTAYLOR'S 079D Diesel heatersTAYLOR'S Code CTK1191Handbook Code Cookers and Stoves 13Handbook Code 079K Kerosene Heater 13Handbook Code 079D Diesel Heater 11Additional to the parts mentioned here, all important spare parts are available from stock.We can order other parts directly from the manufacturer.Please be so free and order the detailed explosion chart or the manual as a copy.

Metering Valve (Fine Taper).Installed before the solenoid valve/drip unit. The drip valve controls the amount of fuel supplied to the burner pot.Spare part for TAYLOR'S 079D diesel heaters.TAYLOR´S Code *HTD5251Handbook Code 36Additional to the parts mentioned here, all important spare parts are available from stock.We can order other parts directly from the manufacturer.Please be so free and order the detailed explosion chart or the manual as a copy.

7 litre petroleum pressure tank from TAYLOR's, e.g. for the 079K petroleum heater, the 028 petroleum cooker or the 029 petroleum cooker with grill.The tank is made of stainless steel and fitted with a bicycle valve (Dunlop or lorry valve). It has a level indicator and a pressure gauge.The pressurised tank can be mounted in any position and is connected to the heater or cooker with a copper pipe.Dimensions: 180 x 340 x 290 mm (D x L x H).

The black steel stove pipe adapter fits ARADA solid fuel stoves with a 5" flue pipe connection. It enables the installation of the 130 mm stove pipes commonly used in Germany.

Add-In Boiler (heat exchanger), welded from thick stainless steel 1.4003, for heating of service water or to connect a small radiator (heating output: approx. 1 kW) .This small boiler is placed inside of the oven and replaces the rear fireclay plate. The pipe connectors for the hot water circuit are 1"and situated at the back. Outlet openings in the back of the oven are pre-fabricated.

WALLAS No. 3419 - The THERMO TWIN PRO insulated air duct from WALLAS is used to conduct warm air in on-board heating systems.The hose is designed for use with hot air heating systems and its insulated design enables low-loss air routing, even over longer distances. compared to a standard hose, heat losses are reduced by 40 %.With an internal diameter of 75 mm and a length of 4 m, the air duct is suitable for distributing heating air in cabins and adjoining rooms. The outer diameter is 90 mm.The construction consists of a flexible air hose with integrated insulation. This reduces the heat dissipation along the hose and at the same time lowers the surface temperature. This supports efficient heat distribution in the system and minimizes condensation.The air duct is designed for connection to corresponding heaters and air distributors with a 75 mm connection diameter.Please note! The product is sold per piece, one piece is 4 meters long.

Through deck exhaust for WALLAS heating systems. To find the best configuration for your boat, please also use the online support at www.wallas.fi/accessories/

Double exhaust tube: Combines the ehaust tube for conbustion gas and the fresh air inlet for combusting air. Flexible double tube, stainless steel.Diameter 28 / 45mm.To put together the installation material for your heating system, you can also use the online support atwww.wallas.fi/accessories/

Thru-bulkhead for WALLAS heating systems. To find the best configuration for your boat, please also use the online support at www.wallas.fi/accessories/

Flexible ribbed hose, D=60mm or D=75mm, for the warm air system of WALLAS heaters.The hose is connected to the intake connection of the heater for the fresh air intake and another hose is attached to the outlet connection of the heater for the transfer of the heated air.To put together the installation material for your heating system, you can also use the online support atwww.wallas.fi/accessories/

Outlet cover with adjustable throttle flap for the 75mm or 60mm hot air system of WALLAS heaters. Made of black plastic. Heat, impact and UV resistant.When installing the warm air system, the throttle flap in the housing can be adjusted so that the desired amount of warm air is discharged at the respective orifice.The ventilation grille must be removed to correct the setting of the throttle valve later. Alternatively, the damper can also be adjusted using a long, narrow object (e.g. a screwdriver) between the grille blades.Scope of delivery:1x housing1x outlet grille (black or white)3x screws 4x15 mm1x hose clipTo assemble your installation material, please also use the online support at www.wallas.fi/accessories/

Y splitter for WALLAS heating systems. To find the best configuration for your boat, please also use the online support at www.wallas.fi/accessories/

Fresh-air outlet for WALLAS heating systems. To find the best configuration for your boat, please also use the online support at www.wallas.fi/accessories/

Tank hookup set for WALLAS heating systems. To find the best configuration for your boat, please also use the online support at www.wallas.fi/accessories/

Insulation stocking made of fibreglass, suitable for the 28/45mm double hose.

On-board grommet for double hose 28/45mm.The double hose consists of the inner exhaust hose 28mm diameter and the outer fresh air hose 45mm diameter. Through the double hose, the exhaust gases are led outboard and at the same time the fresh air necessary for the combustion process is sucked in.There is a bracket on the on-board duct to which the double hose can be fixed with a hose clamp.

On-board grommet for double hose 28/45mm.The double hose consists of the inner exhaust hose 28mm diameter and the outer fresh air hose 45mm diameter. Through the double hose, the exhaust gases are led outboard and at the same time the fresh air necessary for the combustion process is sucked in.There is a bracket on the on-board duct to which the double hose can be fixed with a hose clamp.

Small fuel tank with small footprint for diesel or paraffin, 5 litres

Hot air hose 1m, diameter 75mm, with outlet orifice and 2 hose clamps.Accessory for WALLAS 1300 paraffin heater.This hot air hose extension can be fitted to the WALLAS 1300 paraffin heater instead of the hot air outlet panel. To do this, the outlet panel on the heater must be removed and the outlet nozzle behind it must be turned round.Necessary when installing the heater behind a bulkhead or in a cabinet.

On/off switch available as an accessory for the small WALLAS 1300 paraffin heater.Useful when installing the heater behind a bulkhead or in a cupboard, for example. The switch is supplied with a 6 metre cable.

WALLAS warm air hose connector made of aluminium with two matching hose clamps.

Stainless steel air inlet grille for WALLAS heaters, d = 75 mm.Is inserted into the intake connection of the heaters if no intake hose is used. The air to be heated is then drawn in directly from the area around the heater.The grille protects the heater from the ingress of small parts.

Twisted spiral pipe, single layer, stainless steel.Heat resistant to 600°C. Non-flammable, according to DIN 4102. The bending radius is 1.5 to 3.0 x nominal diameter (mm).

Small reflector plate for heat protection behind flue pipes.Plate stainless steel.Measurements:50cm high, 15cm wide.Available as flat or recessed version.The flat plate must be mounted with spacers or insulation behind, the recessed plate can be mounted directly on the wall.

Very robust through hull outlet made from polished stainless steel A4 (AISI 316) with a plane flange to bolt from the outside.Wall thickness of the tube 2 mm, wall thickness of the flange 4 mm.The flange is 45° angled with the tube.

Flue pipe made from stainless steel (AISI 304), with a thickness of 0,5mm for the inboard exhaust gas routing.The pipes are cylindrical and can be shortened according to any length.Silicone rubber in the shape of a ring acts as the sealant in the rebated joint.

Elbow flue pipe made from stainless steel (AISI 304), with a thickness of 0,5mm for the inboard exhaust gas routing.The elbow flue pipes are cylindrical and are available in angles of 45° or 90°.Silicone rubber in the shape of a ring acts as the sealant in the rebated joint.

To insulate the exhaust pipes we offer tubes made from a highly heat resistant aramid aluminium fabric.Material thickness approx. 1,4 mm, approx. 500 g/m², enduring up to 1000°C radiant heat.

Adapter for reducing diameter of exhaust pipe from 80 mm to 60 mm. Stainless steel.

Very robust through hull outlet made from polished stainless steel A4 (AISI 316) with a flange to bolt from the outside.Wall thickness of the tube 2 mm, wall thickness of the flange 4 mm.The flange is at right angles with the tube.

Chrome-plated replacement door lock for the upper and lower oven door of the SALAMANDER SE and LITTLE RANGE.

The existing cast iron side heat storage plates in the SALAMANDER SE can be replaced with vermiculite plates. The SALAMANDER SE is supplied with cast iron heat storage plates as standard. Compared to the cast-iron plates, the firebox heats up much faster with the vermiculite plates due to their insulating properties, which increases the efficiency of the stove.

Replacement glass for SALAMANDER SE and LITTLE RANGE.

Salamander Multitool, with which the SALAMANDER ovens can also be operated when hot. This tool is supplied with every SALAMANDER SE and every LITTLE RANGE, but is also available as a spare part.The Salamander Multitool is an innovative appliance that offers a wide range of possible uses.to open and close the upper and lower doorto operate the air flow wheel, which regulates the air supply to the fireto operate the vibrating grate to move the ash from the grate into the ash panto pull out and safely transport the ash drawer

The mini shovel and broom set is a useful accessory for the small wood-burning stove! One set is supplied as standard with every SALAMANDER stove. This small, compact set is only 15.5 cm long and 6.5 cm wide.It is ideal for cleaning the combustion chamber before lighting a new fire.Please do not try to clean the stove while it is still hot, otherwise the bristles of the brush will melt!

Optional accessories for the ARADA ECOBURN 5 and HOLBORN 5 stoves include two plinths of different heights, an direct air kit and a rear heat shield .Adding the plinths and thus raising the height of the stove makes it easier to operate, provides a better view of the fire and creates space for storing firewood under the stove.An direct air kit enables the stove to be connected to an external air supply source if required, so that the oxygen for combustion is not taken from the room (flange for connecting a Ø100 mm outside air hose).1 x direct air connection made of unpainted stainless steel2 x fixing screws and washersAttaching the rear heat shield to the back of the stove body reduces the required safety distance between the stove body and non-combustible materials in the installation area of the stove.

Two plinths of different heights, an outside air kit and a rear wall insulation panel are available as optional accessories for the ARADA ECOBURN 5 WIDESCREEN and HOLBORN 5 WIDESCREEN stoves.By adding the plinths and thus raising the height of the stove, operation is made easier, there is a better view of the fire and space is created for storing firewood under the stove.An outside air kit can supply the stove with fresh air from outside in confined spaces so that the oxygen for combustion is not taken from the room. (Flange for connecting an outside air hose Ø100 mm).Attaching the rear heat shield to the back of the stove body reduces the required safety distance between the stove body and non-combustible materials in the area where the stove is installed.

The senotherm® stove spray in black is a heat-resistant special paint for coating and repairing stoves, stove pipes and other metallic surfaces that are exposed to high temperatures. The paint provides a resistant, matt surface.- Heat-resistant up to approx. 500 °C - Suitable for stoves, stovepipes and other metal parts - Easy application with spray can - High-quality, matt look in black - Solvent-based, quick-drying - Content: 150 ml

ARADA connecting flange flange for 5" stove pipes, matt black.Supplied with sealing tape and 3 connecting bolts with nuts and washers.

Oven door handle made of black high-temperature polymer that stays cool enough to touch while the oven is in operation. However, please note that the door will still get hot, so users should take care not to touch the door with the back of their hand unless they are wearing gloves.Suitable for the following ARADA ovens:AX1M-S2, AX1M-S3, AX2M-S2, AX2M-S3, AX6M-INSET, AX5M-INSET, HARDY4M-S3, HARDY5M-S3, EB7HE, EB7HE-G2, EB9HE, EB9HE-G2, EB9HE-G3, EB9HE-G4, EB12HE, EB16HE-G2, EB16HE-G3, EB16HE-G4, EB18HE, EB9HE-INSET, EB12HE-INSET, EB9iHE, EB12iHE, ECB5SCF, ECB4FPLUS, ECB5FPLUS, SIGN5W, SIGN5M, SIGN7W, SIGN7M, SIGNI5W, SIGNI5M, SIGNI7W, SIGNI7M, PUFFIN4M-S2, PUFFIN4M-S3, HERON5M-S2, HERON5M-S3, EB20HE, EB20HE-G2, EB20HE-G3, EB20HE-G4, EB25HE, EB20HE-G2, EB20HE-G3, EB20HE-G4, EB16HE, EB16HE-G2, EB16HE-G3, EB16HE-G4, SEB20, SIGN5M-INSET, SIGN5W-INSET-S2, SIGN7M-INSET-S2, SIGN7W-INSET-S2, SIGN7M-S2, SIGN7W-S2, SIGN7M-S2, SIGN7W-S2, SIGN9M-S2, SIGN9W-S2, SIGN5M-INSET-S2, SIGN5SCF,SIGN5F,SIGN7F, ECB9MCE-S2, ECB5FPLUS-G2, EB16HE-INSET, ECB7MCE-S2, ECB7FPLUS-INSET, ECB5M-INSET-S2, ECB5FPLUS-INSET, ECB9FPLUS, ECB11FPLUS, SOL5MCE-S2, SOL7MCE-S2, SOL9MCE-S2, SOL11MCE-S2, SOL5M-INSET-S2, SOL7M-INSET-S2