Go to homepage
€0.00*
Jobs
Catalogue
Quick order

Impeller pump JABSCO with mechanical cone clutch

With mechanical cone clutch.
These pumps work via a
V-belt and can be coupled by hand when needed.
Pump with high output (specification at 1500 U/min and
a back pressure of 0.3 bar) and self priming from dry.
Well suited as an emergency pump or as a deck-wash pump.
Pump housing, bronze; stainless steel shaft; neoprene impeller.

from €1,165.00*

€1,165.00*

Prices incl. VAT plus shipping costs

model
thread size (inch)
output
Stk
View article in the TOPLICHT catalogue

Description

With mechanical cone clutch.
These pumps work via a
V-belt and can be coupled by hand when needed.
Pump with high output (specification at 1500 U/min and
a back pressure of 0.3 bar) and self priming from dry.
Well suited as an emergency pump or as a deck-wash pump.
Pump housing, bronze; stainless steel shaft; neoprene impeller.

Downloads

Questions about the product?
Talk to craftsmen, boat builders and sailors. We understand your questions and provide the right answers.
Contact experts
Vacuum switch for impeller pumps
Vacuum switch for impeller pumps
For electric impeller pumps.Protects the pump against damage by dry run.The switch is installed on the sucction side of the pump. Cuts the power supply when the pressure drops, caused by a lack of water.Connected to the sucction tube by 1/4" BSP.

€59.90 *
Details
JABSCO Impeller
JABSCO Impeller
Original JABSCO impeller for installation on most cooling water bilge pumps and universal pumps.To keep motors and pumps running smoothly, choosing the right impeller is critical. In addition to the hub mount and size, the material of the impeller should match its application:Neoprene is the most commonly used material for impellers and is suitable wherever only small amounts of oil or diesel fuel are present. Neoprene impellers are therefore suitable for engine cooling and for salt or fresh water pumping.Nitrile is oil resistant and can also be used for heavily polluted water. Impellers made of nitrile are therefore suitable for bilge and bilge pumps.The impellers are usually supplied with a matching paper cover gasket.Other JABSCO impellers and spare parts are also available at short notice on request.To see the matching image for the impeller, simply click on the part number in the table below.

From €37.00 *
Details
Tool for removing impellers JABSCO
Tool for removing impellers JABSCO
An exceptionally practical tool for removing impellers without damaging the pump housing.Body and jaws of aluminum, shaft of stainless steel.Dimensions, approx. 140 x 165 mm (W x H). Weight, 450 g.

From €99.00 *
Details
Grease for impellers JABSCO
Grease for impellers JABSCO
Accessory for JABSCO impellers: JABSCO impeller grease, 2,5 ml tube.

€3.90 *
Details
T-bolt clamp
T-bolt clamp
Heavy, wide hose clamps, made entirely of A2-stainless steel.Hexagonal bolt for easy mounting in hard-to-reach corners. Due to the width particularly well suited for hose mounting on board.Type: HEAVY DUTY.

From €5.90 *
Details
Multiflex hose PVC
Multiflex hose PVC
Green transparent PVC hose for drinking water, bilge pumps (also suction side) and on-board toilets.Spiral strengthened and thick-walled version for use as suction or pressure hose.Approved for human consumption. Limited resistance to oil and grease (may harden).

From €4.90 *
Details
Transparent multiflex hose PVC
Transparent multiflex hose PVC
Transparent, thick-walled hose made of flexible PVC with inserted steel spiral for use as a suction or pressure hose. Well suited for bilge pumps and bilge and grey water systems.Limited resistance to oil and grease (may harden).

From €3.95 *
Details
Impeller pump JABSCO
Impeller pump JABSCO
Self-priming impeller pump with free shaft end. for socket mounting. Equipped with neoprene impeller for use as sea or fresh water pump.The pump housing is made of bronze, the axle with ball bearings is made of stainless steelThe details regarding the output refer to an input speed 1500 U/min and back pressure at 0.3 bar.

From €269.00 *
Details
Impeller pump JABSCO eclectric magnet clutch
Impeller pump JABSCO eclectric magnet clutch
Dry self-priming, belt-driven impeller pumps, can be engaged/disengaged by means of an electric magnetic coupling, 12V or 24V.With electric magnet clutch, 12V or 24V.Pump with high output (specification at 1500 U/min and a back pressure of 0.3 bar).Well suited as emergency pump or as a deck-wash pump.Pump housing, bronze, stainless steel shaft, neoprene impeller.

From €896.00 *
Details

More Products from Category Impeller pumps

Impeller Pump 220 Volt MARCO UP1/AC
Impeller Pump 220 Volt MARCO UP1/AC
Self-priming electric pump for transfer of fresh or salt water with flexible impeller of nitrile rubber which allows the problem-free transit of small particles. Nickel-plated brass body, shaft in stainless steel. AISI 316L. Voltage: 230V-50Hz.Consumption: 3,3 A.Fuse: 4 A.Selfpriming up to 1,5 m height.Flow rate: 30l/min.Pressure: 1 bar.Ports: 1/2" Innengewinde (BSP) or hose diameter: 25 mm.Motorpower: 550 W.Weight: 7,3 kg.Also available for 12 volt or 24 volt. See under similar products.

€369.90 *
Details
Impeller pump 230V JABSCO UTILITY
Impeller pump 230V JABSCO UTILITY
The self-priming 230 V multi-purpose pump JABSCO 53040 UTILITY is a portable pump for filling, pumping out and transferring fresh, salt, and bilge water.The pump is made from bronze, the impeller from oil-proof nitrile rubber, the shaft from stainless steel with a carbon-ceramic mechanical shaft seal. The compact pump can be deployed in multiple ways with its practical handle, is rapidly self-priming from dry up to 4m and will handle hard or soft solids.Air cooled alternate current motor 230 V / 50 Hz, protection class IP55, 0,25 kW at 1400 rpm. With built-in dry-running protection for up to 30 minutes after initial prime

€1,079.00 *
Details
Impeller pump JABSCO
Impeller pump JABSCO
Self-priming impeller pump with free shaft end. for socket mounting. Equipped with neoprene impeller for use as sea or fresh water pump.The pump housing is made of bronze, the axle with ball bearings is made of stainless steelThe details regarding the output refer to an input speed 1500 U/min and back pressure at 0.3 bar.

From €269.00 *
Details
Impeller pump JABSCO eclectric magnet clutch
Impeller pump JABSCO eclectric magnet clutch
Dry self-priming, belt-driven impeller pumps, can be engaged/disengaged by means of an electric magnetic coupling, 12V or 24V.With electric magnet clutch, 12V or 24V.Pump with high output (specification at 1500 U/min and a back pressure of 0.3 bar).Well suited as emergency pump or as a deck-wash pump.Pump housing, bronze, stainless steel shaft, neoprene impeller.

From €896.00 *
Details
Impeller pump JABSCO UTILITY-PUPPY 2000
Impeller pump JABSCO UTILITY-PUPPY 2000
Powerful impeller pump with bronze pump head and impeller made of nitrile rubber (oil-resistant), dry self-priming up to 1.20 m. Developed for pumping bilge water. Dry-running protection up to 20 minutes. Capacity 32 l/min at 3 m (0.3 bar) or 27 l/m at 5 m (0.5 bar), suitable for continuous operation.Dimensions 190x120x80 mm.Versions for 12V or 24V on-board voltage are available. Connection 3/4" (inside).

From €439.00 *
Details
Impeller pump JABSCO with mechanical cone clutch
Impeller pump JABSCO with mechanical cone clutch
With mechanical cone clutch.These pumps work via a V-belt and can be coupled by hand when needed. Pump with high output (specification at 1500 U/min and a back pressure of 0.3 bar) and self priming from dry. Well suited as an emergency pump or as a deck-wash pump. Pump housing, bronze; stainless steel shaft; neoprene impeller.

From €1,165.00 *
Details
Impeller Pump MARCO UP1
Impeller Pump MARCO UP1
Self-priming electric water pump with with nitrile rubber impeller. The pump body is made of nickel-plated brass. The pump is dry self-priming up to 1.5 m height.The connections have a BSP female thread. A direct hose connection to the connection pieces is also possible.Available in two power ratings for 12 or 24 volts.Also available for 220 volts, see matching items. See similar articles.

From €134.01 *
Details
Impeller pump WATER-PUPPY 2000
Impeller pump WATER-PUPPY 2000
Efficient electric pump with bronze pump head and impeller of nitrile rubber (oil-proof), dry self-priming to 1.2 m.Power 32 l/min at 3 m (0.3 bar) or 27 l/m at 5 m (0.5 bar), intended for endurance use.Dimensions 190 x 120 x 80 mm.Attachment 1/2" (inner) or 25mm hose.Versions for 12V or 24V on-board voltage are available.Also available is the JABSCO UTILITY PUPPY 2000 version specially designed for pumping bilge water with 20-minute dry-running protection.

From €269.00 *
Details
Impeller pump with reverse switch MARCO UP1-JR
Impeller pump with reverse switch MARCO UP1-JR
This universal feed pump for freshwater and seawater has a hard-wearing impeller made of nitrile rubber. The motor is equipped with an integrated waterproof switch with three positions (forward/off/reverse) so that the flow direction can be changed.This compact design makes the impeller pump ideal for transferring water or grey water, as well as for emptying bilges and grey water. The pump body is made of nickel-plated brass and the impeller is made of hard-wearing nitrile rubber. The pump is dry self-priming up to a height of 1.5 metres. The connecting pieces allow direct hose connection, but also have BSP internal threads, so that connection with appropriate fittings is also possible.Available in two performance levels for 12 over 24 volts.You can find other MARCO pumps in the UP1 series under the "Similar products" tab.

From €149.00 *
Details
Tool for removing impellers JABSCO
Tool for removing impellers JABSCO
An exceptionally practical tool for removing impellers without damaging the pump housing.Body and jaws of aluminum, shaft of stainless steel.Dimensions, approx. 140 x 165 mm (W x H). Weight, 450 g.

From €99.00 *
Details

Last seen products