Impeller pump JABSCO | TOPLICHT

To be able to use the full range of Shopware 6, we recommend activating Javascript in your browser.

Art. No.	model	thread size (inch)	output	Price (unit)	Delivery time	Note list	Buy

Description

Self-priming impeller pump with free shaft end. for socket mounting. Equipped with neoprene impeller for use as sea or fresh water pump.

The pump housing is made of bronze, the axle with ball bearings is made of stainless steel

The details regarding the output refer to an input speed 1500 U/min and back pressure at 0.3 bar.

Questions about the product?

Talk to craftsmen, boat builders and sailors. We understand your questions and provide the right answers.

Contact experts

JABSCO Impeller

JABSCO Impeller

Original JABSCO impeller for installation on most cooling water bilge pumps and universal pumps.To keep motors and pumps running smoothly, choosing the right impeller is critical. In addition to the hub mount and size, the material of the impeller should match its application:Neoprene is the most commonly used material for impellers and is suitable wherever only small amounts of oil or diesel fuel are present. Neoprene impellers are therefore suitable for engine cooling and for salt or fresh water pumping.Nitrile is oil resistant and can also be used for heavily polluted water. Impellers made of nitrile are therefore suitable for bilge and bilge pumps.The impellers are usually supplied with a matching paper cover gasket.Other JABSCO impellers and spare parts are also available at short notice on request.To see the matching image for the impeller, simply click on the part number in the table below.

From €37.00 *

Tool for removing impellers JABSCO

Tool for removing impellers JABSCO

An exceptionally practical tool for removing impellers without damaging the pump housing.Body and jaws of aluminum, shaft of stainless steel.Dimensions, approx. 140 x 165 mm (W x H). Weight, 450 g.

From €99.00 *

Grease for impellers JABSCO

Grease for impellers JABSCO

Accessory for JABSCO impellers: JABSCO impeller grease, 2,5 ml tube.

€3.90 *

Brass check valve

Brass check valve

Brass check valve, spring operated.To be fitted in the tube to prevent reflux of water.With inner threads on both sides. Strong body of brass, valve cage of nylon, spring of A2 stainless steel, seal of nitrile rubber.The valve works in any installation situation.Thread type: BSPThread form: parallelThe thread sizes are nominal sizes, they do not indicate the thread diameter.

From €10.90 *

Brass pipe-to-hose fitting

Brass pipe-to-hose fitting

Brass pipe-to-hose fitting with external thread and hexagon. Available for different hose diameters.Thread type: BSPThread form: parallelThe thread sizes are nominal sizes and do not indicate the thread diameter.

From €3.20 *

Bronze pipe-to-hose fitting

Bronze pipe-to-hose fitting

Bronze pipe-to-hose fitting with external thread and hexagon. Available for different hose diameters.Thread type: BSPThread form: parallelThe thread sizes are nominal sizes, they do not indicate the thread diameter.

From €7.65 *

Brass pipe-to-hose fitting 45° with external thread

Brass pipe-to-hose fitting 45° with external thread

45° elbow pipe-to-hose fitting made of brass, with external thread and attachment for screwing in. Available for various hose diameters.Thread type: BSPThread form: parallelThe thread sizes are nominal sizes, they do not indicate the thread diameter.

From €10.31 *

Multiflex hose PVC

Multiflex hose PVC

Green transparent PVC hose for drinking water, bilge pumps (also suction side) and on-board toilets.Spiral strengthened and thick-walled version for use as suction or pressure hose.Approved for human consumption. Limited resistance to oil and grease (may harden).

From €4.90 *

Transparent multiflex hose PVC

Transparent multiflex hose PVC

Transparent, thick-walled hose made of flexible PVC with inserted steel spiral for use as a suction or pressure hose. Well suited for bilge pumps and bilge and grey water systems.Limited resistance to oil and grease (may harden).

From €3.95 *

VETUS waterlock / exhaust silencer WLOCK

VETUS waterlock / exhaust silencer WLOCK

Tried and tested waterlock for engine installations with water cooled exhaust systems.Robust PVC silencer in a z design of the type WLOCK for standing or hanging mounting, with twistable inlet for many installation situations.Good to very good noise absorption. With drainage nozzle.We have three of the most common designs on offer (see the Suitable Items further down below). Various additional designs are available upon request.

From €169.00 *

Exhaust Pipe

Original Vetus exhaust hose in very flexible exhaust hose with Lloyds approval.The special type of rubber and the tightly wound inner spiral enable installation even in confined spaces. The possible bending radius is one and a half times the diameter.Temperature-resistant from -30° C to +100° C with a short-term peak load of +115° C.Only sections in whole 1 meter increments are available. Customized goods cannot be returned.Other hose diameters on request.

Price on request

Siphonbreak vent

Siphonbreak vent

Loop valve. Nickel-plated brass.For installation in outlet toilet or pump tubing or in water cooled engine exhaust (does not work on the inlet side).Prevention against the siphon effect in tubes and pipes.Opens under vacuum pressure.Sensing function through a rubber valve ball.Easy cleaning through top screw.The picture shows a possible installtion. Tubing, elbows and hose nipples are not included and must be ordered separately, if required.

€21.00 *

VETUS AIRVENT anti syphon

VETUS AIRVENT anti syphon

Anti syphon for motor cooling water outlet or for toilet outlet. Can be connected to hoses with internal diameters of 13, 19, 25 and 32 mm. AIRVENT H without valve, comes with 4,0 m plastic hose diameter 8 mm. AIRVENT V with spring loaded valve.

From €115.00 *

VETUS Gooseneck for exhaust systems WLOCKLT

VETUS Gooseneck for exhaust systems WLOCKLT

Gooseneck for exhaust hose. Raises the exhaust hose above the waterline so that water cannot backfill the exhaust system.

From €147.50 *

VETUS exhaust flange stainless steel

VETUS exhaust flange stainless steel

Transom exhaust connection, with integrated check valve TYP TRCSV. High quality stainless steel AISI 316 with high gloss polished cover to conceal fixings. The flanges are fitted from the outside and do not need a lock bush from the inside. The exhaust hose can be fitted directly to this transom connection.

From €110.00 *

VETUS waterlock / exhaust silencer NLPH

VETUS waterlock / exhaust silencer NLPH

Tried and tested waterlock for engine installations with water cooled exhaust systems.Robust PVC silencer of the horizontal type NLPH with slim and twistable muffler with twistable connectors for many installation situations.Good to very good noise absorption. With drainage nozzle.We have three of the most common designs on offer (see the Suitable Items further down below). Various additional designs are available upon request.

From €229.00 *

Cooling water strainer VETUS Typ FTR 330

Cooling water strainer VETUS Typ FTR 330

Proven VETUS FTR 300 cooling water filter in all-plastic design.The transparent cover is ideal for constant monitoring and quick inspection of the degree of contamination.The large, active surface is easy to clean.The optional lid spanner can be used to open the cross lid more easily. You can find this, as well as replacement filter elements, O-rings or replacement lids, further down on this page under "Accessories".

From €107.50 *

Sea water strainer nickel plated brass 1162 poly-lid

Sea water strainer nickel plated brass 1162 poly-lid

Heavy seawater filter Type 1162 of nickel-plated brass. The filter cartridge is made of V4A stainless steel.The top covers of transparent polycarbonate and O-Ring seals allow easy inspection and control of the filter.Intake and outlet on the sides.Other options are available.Approved by RINA.

From €139.90 *

More Products from Category Cooling water pumps

Centrifugal pump JABSCO

Centrifugal pump JABSCO

JABSCO centrifugal pumps CYCLONE are strong and durable pumps made from stainless steel, suitable as circulation pump for heating systems, ballast tank systems, cooling water or seawater, diesel or chemicals over a temperature range of +4° to 95°C.They are available as high efficiency pumps (type 50840) with up to 110 l/min power for continuous operation or as high pressure pumps (type 50860) for the temporally limited usage (30 min maximum) with pressure of up to 1,6 bar.Connection thread 3/4" BSP.Four rubber puffer pads in the base plate ensure a quite and vibration free operation.Centrifugal pumps are not self-priming, they must therefore be installed in such a way, that the flow of the pumped medium is guaranteed.

From €499.00 *

Impeller pump JABSCO

Impeller pump JABSCO

Self-priming impeller pump with free shaft end. for socket mounting. Equipped with neoprene impeller for use as sea or fresh water pump.The pump housing is made of bronze, the axle with ball bearings is made of stainless steelThe details regarding the output refer to an input speed 1500 U/min and back pressure at 0.3 bar.

From €269.00 *

Last seen products

Request sent successfully

Request wasn't send - a error occured. Please try again.