- Rigg & sail
- Rope & cordage
- Anchoring & mooring
- Hull & deck
- Cabin & comfort
- Paint & boatbuilding
- Electrics & engine
- Pumps & sanitation
- Safety & VHF radio
- Navigation & books
- Commercial shipping
The RULE-MATE is an automatic bilge pump, controlled by an electronic water level sensor integrated into the housing and does not require a separate float switch. As soon as water reaches the sensor area, the pump starts automatically and pumps out the bilge water. When the water level drops again, the pump switches off automatically.
According to the manufacturer, the RM500, RM800 and RM1100 models start at a water level of approximately 5 cm and switch off again when the residual water level is approximately 0.9 cm. The RM2000 starts at a water level of approximately 7 cm.
Unlike the time-controlled automatic pumps of the RULE-AUTOMATIC/RA series (see Similar Products), the RULE-MATE does not start at fixed intervals during normal operation, but reacts to the actual water level. The manufacturer refers to this function as ‘Auto Sense Intelligence’. If the sensor is obstructed by debris or the pump runs without delivering water, a backup function prevents continuous operation: the pump then switches to a cyclic check mode with a 2.5-minute interval.
The actual flow rate depends on the delivery head, the hose routing and the connection diameter used. As the delivery head increases, the flow rate decreases. The TOPLICHT product table therefore lists not only the maximum flow rate but also the flow rate at 1 m water column; depending on the model, this ranges between 23 and 93 l/min for the RULE-MATE pumps on offer.
The series features a plastic housing with an easily removable strainer base plate. The motor is fully enclosed, and the shaft is made of stainless steel and fitted with a special seal. The unit is supplied with straight hose connections. Depending on the model, a range of flow rates, connection diameters and operating voltages are available.
Technical features
- Automatic bilge pump with integrated electronic water level sensor
- Available in versions for 12 V or 24 V on-board power supply
- No separate float switch required
- Automatic start-up when water level is detected
- Automatic shut-off when water level drops
- Start-up water level RM500/RM800/RM1100: approx. 5 cm
- Shut-off RM500/RM800/RM1100: approx. 0.9 cm residual water level
- Start-up water level RM2000: approx. 7 cm
- Backup function with 2.5-minute test mode in the event of a faulty sensor or lack of water flow
- Plastic housing with easily removable strainer base plate
- Fully enclosed motor
- Supplied with straight hose connectors
from €129.00*
€129.00
Prices incl. VAT plus shipping costs
| Art. No. | model | voltage (V) | current (A) | Max. (l/min) | l/min at 1m Wc | D1 (mm) | B (mm) | L (mm) | H (mm) | Unit price | Delivery time | Note list | Buy |
|---|
Description
The RULE-MATE is an automatic bilge pump, controlled by an electronic water level sensor integrated into the housing and does not require a separate float switch. As soon as water reaches the sensor area, the pump starts automatically and pumps out the bilge water. When the water level drops again, the pump switches off automatically.
According to the manufacturer, the RM500, RM800 and RM1100 models start at a water level of approximately 5 cm and switch off again when the residual water level is approximately 0.9 cm. The RM2000 starts at a water level of approximately 7 cm.
Unlike the time-controlled automatic pumps of the RULE-AUTOMATIC/RA series (see Similar Products), the RULE-MATE does not start at fixed intervals during normal operation, but reacts to the actual water level. The manufacturer refers to this function as ‘Auto Sense Intelligence’. If the sensor is obstructed by debris or the pump runs without delivering water, a backup function prevents continuous operation: the pump then switches to a cyclic check mode with a 2.5-minute interval.
The actual flow rate depends on the delivery head, the hose routing and the connection diameter used. As the delivery head increases, the flow rate decreases. The TOPLICHT product table therefore lists not only the maximum flow rate but also the flow rate at 1 m water column; depending on the model, this ranges between 23 and 93 l/min for the RULE-MATE pumps on offer.
The series features a plastic housing with an easily removable strainer base plate. The motor is fully enclosed, and the shaft is made of stainless steel and fitted with a special seal. The unit is supplied with straight hose connections. Depending on the model, a range of flow rates, connection diameters and operating voltages are available.
Technical features
- Automatic bilge pump with integrated electronic water level sensor
- Available in versions for 12 V or 24 V on-board power supply
- No separate float switch required
- Automatic start-up when water level is detected
- Automatic shut-off when water level drops
- Start-up water level RM500/RM800/RM1100: approx. 5 cm
- Shut-off RM500/RM800/RM1100: approx. 0.9 cm residual water level
- Start-up water level RM2000: approx. 7 cm
- Backup function with 2.5-minute test mode in the event of a faulty sensor or lack of water flow
- Plastic housing with easily removable strainer base plate
- Fully enclosed motor
- Supplied with straight hose connectors
Downloads
Green transparent PVC hose for drinking water, bilge pumps (also suction side) and on-board toilets.Spiral strengthened and thick-walled version for use as suction or pressure hose.Approved for human consumption. Limited resistance to oil and grease (may harden).
Transparent, thick-walled hose made of flexible PVC with inserted steel spiral for use as a suction or pressure hose. Well suited for bilge pumps and bilge and grey water systems.Limited resistance to oil and grease (may harden).
Solid stainless steel design - all pieces completely stainless.With hexagonal bolts for high torque, high tear resistance and elasticity.
Heavy, wide hose clamps, made entirely of A2-stainless steel.Hexagonal bolt for easy mounting in hard-to-reach corners. Due to the width particularly well suited for hose mounting on board.Type: HEAVY DUTY.
Brand name three-way switch for bilge pumps with high switching capacity but without a fuse holder. Black coloured stainless steel panel.For on-board voltage of 12 Volt and 24 Volt. For manual pumping the switch has to be pressed from the OFF position to the right (push-button function).
The tried-and-tested RULE-AUTOMATIC (RA) bilge pumps feature a built-in microprocessor which checks for the presence of water every 150 seconds by briefly activating the pump (without a mechanical switch). Power consumption for the test run is low at approx. 0.2–0.5 Ah per day. Whilst conventional bilge pumps with float switches typically activate at a water level of around 5 cm, the RULE-AUTOMATIC switches on at around 1.6 cm and pumps the bilge water down to a residual water level of around 0.6 cm.The series features a plastic housing, an easily removable strainer base plate and a quiet-running, fully enclosed motor. The non-return valve reduces the backflow of water into the bilge, whilst concealed vents in the pump housing prevent air pockets in the hose installations. The threaded outlet allows the use of different hose connectors, depending on the specific model and connection diameter.Technical featuresAutomatic bilge pump for 12-volt on-board electrical systemsElectronic water level control without a mechanical float switchTest run every 150 secondsActivation level approx. 1.6 cmPumps down to approx. 0.6 cm residual water levelPlastic housing with removable strainer base plateFully enclosed motorNon-return valve to reduce backflow of waterConcealed vents in the housing to prevent air pockets
Powerful submersible pump from RULE. The pump is made of sturdy plastic and is ideal for smaller boats due to its light and compact nature.The motor is fully enclosed and runs very quietly. The shafts can not rust and are specially sealed against water penetration.The inlet strainer of the pump can be easily removed to clean the pump. The check valve prevents water from flowing back into the bilge, and the ventilated housing optimally prevents air pockets.A thermal shutdown prevents overheating and protects the pump.Also available as RULE AUTOMATIC (RA) automatic pumps. See under similar products.
Flat, powerful bilge pump for tight spaces with freely adjustable hose outlet (vertical/horizontal) for 3 different hose diameters (19, 25 and 28 mm). All hose nozzles have lip check valves, the motor unit is removable for cleaning, maximum pumping height is 3.4 m.Pumping capacity: 3373 l/h at the same level.2400 l/h at 1 m height difference (1 mWS).Available as standard pump (type LP900D) or as automatic pump (type LP900S) with integrated sensor switch.The sensor has 3 switching modes: in mode "L" the pump switches on at a water height of 33 mm, in mode "H" at 50 mm, in mode "Time" the pump checks every 150 seconds by a short start if water is present and then pumps until the bilge is empty.
High-performance bilge pump, available in various sizes for 12V or 24V systems. Discharge head up to 3 m.The snap-off plastic housing can be opened easily for maintenance and cleaning. Low power requirements.Stainless-steel shaft with a high-quality seal.Built in Italy by MARCO.
Extremely low-profile, submersible pump with good power, by the renowned pump manufacturer WHALE, which can also be placed between frames and floor boards.Removable sieve, outflow hose adjustable from horizontal to vertical.This version requires a separate pump/bilge switch (see accessories). Article 1441-111 comes with a non-return valve. Versions:SUPERSUB 5012 has a max. pump output of 32 l/min and 25 l/min at 1 meter height. , SUPERSUB 1012 has a max. pump output of 66 l/min and 47 l/min at 1 meter height.Also available in the WHALE SUPERSUB SMART version with automatic sensor switch.
Extremely low-profile, submersible pump with good power, by the renowned pump manufacturer WHALE, which can also be placed between frames and floor boards.Equipped with a built in, maintenance free 'electric field sensor' as integrated float switch, removable sieve and non-return valve. Drains to down 9 mm.Outflow hose adjustable from horizontal to vertical.Versions: SUPERSUB SMART 5212 has a max. pump output of 40 l/min and 34 l/min at 1 meter height. SUPERSUB SMART 1212 and 1224 have a pump output of 66 l/min and 47 l/min at 1 meter height.
Submersible bilgepump with strong permanent magnet motor and special shaft seals.The outer cover can be removed for inspection.Shaft of rust-free steel.These pumps are only partially protected against dry-running, so the installation of the optional floating or sensor switch is recommended.
Through-hull with attached hose nozzle. Made of brass (seawater resistant brass, depending on manufacturer CW602N - CuZn36Pb2AS or CW625N - CuZn35Pb1,5AlAs).Comes in rolled brass or with a chromed finish.Thread type: BSPThread form: parallelThe thread sizes are nominal sizes, they do not indicate the thread diameter.
The MARPOL Convention prohibits the discharge of oily wastewater into the sea. This filter removes the oily substances from the pumped bilge water by a patented filter system, so that the bilge water can be pumped out almost without oil residues and the water pollution is minimized.The filter is installed behind the bilge pump and in front of the ship's passage. It is suitable for oil residues, large dirt must be removed from the bilge before.Supplied with a stainless steel wall mounting plate.Replacement filter cartridges are available, annual replacement is recommended.LLOYD'S REGISTER Type Approved.
High-performance bilge pump, available in various sizes for 12V or 24V systems. Discharge head up to 3 m.The snap-off plastic housing can be opened easily for maintenance and cleaning. Low power requirements.Stainless-steel shaft with a high-quality seal.Built in Italy by MARCO.
The tried-and-tested RULE-AUTOMATIC (RA) bilge pumps feature a built-in microprocessor which checks for the presence of water every 150 seconds by briefly activating the pump (without a mechanical switch). Power consumption for the test run is low at approx. 0.2–0.5 Ah per day. Whilst conventional bilge pumps with float switches typically activate at a water level of around 5 cm, the RULE-AUTOMATIC switches on at around 1.6 cm and pumps the bilge water down to a residual water level of around 0.6 cm.The series features a plastic housing, an easily removable strainer base plate and a quiet-running, fully enclosed motor. The non-return valve reduces the backflow of water into the bilge, whilst concealed vents in the pump housing prevent air pockets in the hose installations. The threaded outlet allows the use of different hose connectors, depending on the specific model and connection diameter.Technical featuresAutomatic bilge pump for 12-volt on-board electrical systemsElectronic water level control without a mechanical float switchTest run every 150 secondsActivation level approx. 1.6 cmPumps down to approx. 0.6 cm residual water levelPlastic housing with removable strainer base plateFully enclosed motorNon-return valve to reduce backflow of waterConcealed vents in the housing to prevent air pockets
The RULE-MATE is an automatic bilge pump, controlled by an electronic water level sensor integrated into the housing and does not require a separate float switch. As soon as water reaches the sensor area, the pump starts automatically and pumps out the bilge water. When the water level drops again, the pump switches off automatically.According to the manufacturer, the RM500, RM800 and RM1100 models start at a water level of approximately 5 cm and switch off again when the residual water level is approximately 0.9 cm. The RM2000 starts at a water level of approximately 7 cm.Unlike the time-controlled automatic pumps of the RULE-AUTOMATIC/RA series (see Similar Products), the RULE-MATE does not start at fixed intervals during normal operation, but reacts to the actual water level. The manufacturer refers to this function as ‘Auto Sense Intelligence’. If the sensor is obstructed by debris or the pump runs without delivering water, a backup function prevents continuous operation: the pump then switches to a cyclic check mode with a 2.5-minute interval.The actual flow rate depends on the delivery head, the hose routing and the connection diameter used. As the delivery head increases, the flow rate decreases. The TOPLICHT product table therefore lists not only the maximum flow rate but also the flow rate at 1 m water column; depending on the model, this ranges between 23 and 93 l/min for the RULE-MATE pumps on offer.The series features a plastic housing with an easily removable strainer base plate. The motor is fully enclosed, and the shaft is made of stainless steel and fitted with a special seal. The unit is supplied with straight hose connections. Depending on the model, a range of flow rates, connection diameters and operating voltages are available.Technical featuresAutomatic bilge pump with integrated electronic water level sensorAvailable in versions for 12 V or 24 V on-board power supplyNo separate float switch requiredAutomatic start-up when water level is detectedAutomatic shut-off when water level dropsStart-up water level RM500/RM800/RM1100: approx. 5 cmShut-off RM500/RM800/RM1100: approx. 0.9 cm residual water levelStart-up water level RM2000: approx. 7 cmBackup function with 2.5-minute test mode in the event of a faulty sensor or lack of water flowPlastic housing with easily removable strainer base plateFully enclosed motorSupplied with straight hose connectors
Submersible bilgepump with strong permanent magnet motor and special shaft seals.The outer cover can be removed for inspection.Shaft of rust-free steel.These pumps are only partially protected against dry-running, so the installation of the optional floating or sensor switch is recommended.
WHALE GULPER type 220: Electric membrane pump for pumping the bilge or emptying the head or holding tank (grey water pump). Self-priming. Suction lift max. 3 m, dicharge head max. 3 m, combined suction lift / discharge head max. 4m.Odorless running, vibration absorbing rubber feet.Universal installation due to swiveling pump heads.For tube 19mm. Weight 1.5 kg. Dimensions: L x W x H = 273 x 111 x 117 mm. Spare-parts sets available.
WHALE GULPER type 320: Electric membrane pump for pumping the bilge or pumping out the head or holding tank (grey water pump). Self-priming. Suction lift max. 3m, dicharge head max. 3 m, combined suction lift / discharge head max. 4m.Odorless running, vibration absorbing rubber feet.Universal installation due to swiveling pump heads.A variable tube adaptor connects the GULPER 320 to 19mm or 25mm tube. Weight 1.6 kg. Dimensions: L x W x H = 273 x 111 x 117 mm. Spare-parts sets available.
A new generation of diaphragm pump in the one compartment design by pump specialist JABSCO.Ideal for the draining of shallow bilges and shower drains.Maintanance is simplified by the filterless design and the pump is indeed free of clogging.Characteristics:Flow rate: Nominal 16 Litres/min. Self-priming from dry up to 3m (10ft) Flexible installation Dry running capability
Powerful impeller pump with bronze pump head and impeller made of nitrile rubber (oil-resistant), dry self-priming up to 1.20 m. Developed for pumping bilge water. Dry-running protection up to 20 minutes. Capacity 32 l/min at 3 m (0.3 bar) or 27 l/m at 5 m (0.5 bar), suitable for continuous operation.Dimensions 190x120x80 mm.Versions for 12V or 24V on-board voltage are available. Connection 3/4" (inside).
Self-priming electric water pump with with nitrile rubber impeller. The pump body is made of nickel-plated brass. The pump is dry self-priming up to 1.5 m height.The connections have a BSP female thread. A direct hose connection to the connection pieces is also possible.Available in two power ratings for 12 or 24 volts.Also available for 220 volts, see matching items. See similar articles.
This self-priming bilge and deck wash pump is suitable for delivering sea water. It is completely made of bronze and stainless steel. Due to its hard-wearing industrial motor a longlasting and reliable operation is guaranteed. Before it is run for the first time it has to be filled with water. Furthermore it is advisable to install a socket safety valve or a foot operated valve into the suction pipe. The pump is non-reactive to sand (particle size up to 2 mm). The model 4 E is totally maintenance-free due to the use of a freely running impeller wheel and a very modern axial face seal. The max. operating time is 1 – 2 hoursTechnical dataOutput:50 l/minHeight pumped: 13 mSuction lift: 3 mAttachment: 3/4" BSP with inner threadsWeight: 7 kg
Very powerful, self-priming electrical diaphragm pump with reliable industrial motor.This Rheinstrom diaphragm pump has been found to be very reliable over many years. It can be used as a bilge pump, a grey water pump and a delivery pump.Constant delivery rate, high safety against clogging, very good cleaning possibilities.Made of hard-wearing materials, the body is made of seawater-proof cast bronze.Fast and easy cleaning and maintenance and direct access to the valves are obtained by simply opening the lid of the pump. The discharge and suction side may be altered.Technical dataPump performance: 40 l/minDelivery head: 10 mSuction height: 3,5 mConnection: 38 mm hose connectionMotor: 110 WWeight: 9,5 kgA repair kit is available.
Flat, powerful bilge pump for tight spaces with freely adjustable hose outlet (vertical/horizontal) for 3 different hose diameters (19, 25 and 28 mm). All hose nozzles have lip check valves, the motor unit is removable for cleaning, maximum pumping height is 3.4 m.Pumping capacity: 3373 l/h at the same level.2400 l/h at 1 m height difference (1 mWS).Available as standard pump (type LP900D) or as automatic pump (type LP900S) with integrated sensor switch.The sensor has 3 switching modes: in mode "L" the pump switches on at a water height of 33 mm, in mode "H" at 50 mm, in mode "Time" the pump checks every 150 seconds by a short start if water is present and then pumps until the bilge is empty.
Extremely low-profile, submersible pump with good power, by the renowned pump manufacturer WHALE, which can also be placed between frames and floor boards.Removable sieve, outflow hose adjustable from horizontal to vertical.This version requires a separate pump/bilge switch (see accessories). Article 1441-111 comes with a non-return valve. Versions:SUPERSUB 5012 has a max. pump output of 32 l/min and 25 l/min at 1 meter height. , SUPERSUB 1012 has a max. pump output of 66 l/min and 47 l/min at 1 meter height.Also available in the WHALE SUPERSUB SMART version with automatic sensor switch.
Extremely low-profile, submersible pump with good power, by the renowned pump manufacturer WHALE, which can also be placed between frames and floor boards.Equipped with a built in, maintenance free 'electric field sensor' as integrated float switch, removable sieve and non-return valve. Drains to down 9 mm.Outflow hose adjustable from horizontal to vertical.Versions: SUPERSUB SMART 5212 has a max. pump output of 40 l/min and 34 l/min at 1 meter height. SUPERSUB SMART 1212 and 1224 have a pump output of 66 l/min and 47 l/min at 1 meter height.
Powerful submersible pump from RULE. The pump is made of sturdy plastic and is ideal for smaller boats due to its light and compact nature.The motor is fully enclosed and runs very quietly. The shafts can not rust and are specially sealed against water penetration.The inlet strainer of the pump can be easily removed to clean the pump. The check valve prevents water from flowing back into the bilge, and the ventilated housing optimally prevents air pockets.A thermal shutdown prevents overheating and protects the pump.Also available as RULE AUTOMATIC (RA) automatic pumps. See under similar products.
