Transparent glass powder for full or partial scattering on COELAN coating systems to increase slip resistance. The product is suitable for all areas where increased slip resistance is required on coated surfaces. It is applied in combination with a fresh adhesive layer and is compatible with transparent and pigmented COELAN systems as well as all common 1- and 2-component coatings.Application: The product is sprinkled into the still tacky coating surface after painting &nbsp

Transparent, glossy 1-component coating based on polyurethane resin for wood, plastic, and metal surfaces. COELAN Boat Coating Glossy is suitable for boat decks and all areas above the waterline.The product is UV-resistant, highly elastic, and remains breathable: water vapor can still diffuse from the coated material. Due to its extremely good weather resistance, long renovation intervals result. As a final coat (last layer), COELAN Boat Coating SILK MATT (matching articles) can also be applied. The boat coating can also be colored with COELAN color pastes (e.g., white, Art. No. 2622-1013).Application: The processing temperature should be between +5 °C and +30 °C. During processing and curing, ensure even ventilation, and personal protective equipment (gloves, respiratory mask) should be worn for safety. Depending on the substrate, pre-treatment with a suitable COELAN boat primer is required. Application is done in several even, generous layers with a brush or foam roller. For vertical surfaces, dilution with 10–30 % COELAN thinner is recommended. Depending on the area of use (walkable decks, masts, superstructures), 6-8 layers are required.Contains isocyanates. May cause allergic reactions. From August 24, 2023, appropriate training must be completed before industrial or commercial use (REACH Regulation Annex XVII)Technical DataArea of application: Transparent high-gloss coating for wood, plastic, and metal surfaces above the waterlineSubstrate: Requires COELAN boat primer depending on materialPrimer: COELAN boat primer (Art. No. 2620-001 or -101)Coverage: 1 l/m² Thinner: max. 30 % COELAN thinnerApplication method: Brush or foam rollerDrying times (at 23 °C, 50 % r.h.): Skin formation: approx. 2 hrs, walkable and recoatable: approx. 6 hrs, normally loadable: approx. 2 days, fully loadable: approx. 7 daysFurther information on processing can be found in the technical data sheet under 'Downloads'.

A transparent, semi-matt 1-component coating based on polyurethane. COELAN Boat Coating Silk Matt serves as a satin finishing coat on surfaces that have previously been coated with COELAN Boat Coating Gloss. The product is characterized by its durability, UV and weather resistance, high elasticity and abrasion resistance as well as easy cleaning.Application: Ideally, the product should be stored at room temperature for 24 hours before application and applied at temperatures between 5 °C and 30 °C. The coating is applied evenly with a foam roller or brush. Personal protective equipment such as gloves and a respirator must be worn during application. The product is ready to use, but can be adjusted with max. 30 % COELAN thinner if necessary.

Transparent adhesion promoter based on polyurethane resin for various interior and exterior plastic surfaces. COELAN Flexo Adhesion Primer is particularly suitable for reworking already hardened COELAN products based on polyurethane or epoxy resin, if these are to be further coated in color. Not suitable for substrates made of polyethylene (PE) or polypropylene (PP).Application: Existing COELAN polyurethane coatings must be cured for at least 7 days, epoxy resin coatings for at least 24 hours. Store the container at room temperature for approx. 24 hours before use. Apply the product evenly, thinly and over the entire surface using a cloth.

COELAN Color Pastes are suitable for coloring transparent, glossy COELAN Polyurethane Boat Coating (Art.No. 2621-075). The color pastes are ready to use and available in seven color shades. The opacity may vary depending on the color shade.Application: The color paste is stirred directly into the transparent COELAN Boat Coating in a maximum quantity of 10 %. Mix in the paste with a stirring rod or by machine with a slow-running agitator (max. 300 rpm). Once opened, tubes should be sealed airtight and used up promptly.Note on the color chart: The colors shown correspond as closely as possible to the original colors, but deviations cannot be ruled out.Technical dataArea of application: Coloring of COELAN polyurethane oatingsMixing ratio: max. 10 % addition to the coating quantityFurther information on processing can be found in the technical data sheet under 'Downloads'.

COELAN Boat Primer is a 1-component polyurethane primer for the pretreatment of hardwood and softwood surfaces in conjunction with the transparent COELAN boat coating system. The pigmented glaze improves adhesion, provides a color match to the wood, and ensures a light-resistant base tint. It is slightly thixotropic (less dripping), quick-drying, and contains no biocides or fungicides. Available color shades:- yellowish translucent for softwoods and hardwoods such as teak, pine, fir, larch, spruce- reddish translucent for light-sensitive woods such as mahoganyApplication: The wood surface must be clean, dry, and free from separating substances. The processing temperature should be between +5 °C and +30 °C and a maximum of 80% relative humidity. The product is ready to use and should be stored at room temperature for approx. 24 hours before use.The primer is applied with a foam roller or brush to the sanded wood surface (grit 80). Tools can be cleaned with COELAN thinner (Art.No. 2629-001). During application and curing, ensure even ventilation, and personal protective equipment (gloves, respirator mask) should be worn for safety. Contains isocyanates. May cause allergic reactions. As of August 24, 2023, appropriate training must be completed before industrial or commercial use (according to REACH).Technical DataApplication area: Primer for hardwood and softwood in conjunction with COELAN boat coatingSubstrate: Clean, dry, sanded woodCoverage: min. 200 ml/m² (depending on absorbency, in several steps)Thinning: not recommendedApplication method: Foam roller, ring or flat brushDrying times (at 23 °C): Recoatable after approx. 2–3 hoursFor more information on application, please refer to the Technical Data Sheet under 'Downloads'.

Thinner and cleaner for COELAN Boat Coating (e.g. Art. No. 2624-075). COELAN Thinner is added directly to COELAN Boat Coating as required to improve the application properties at lower temperatures or on vertical surfaces, for example. It is also suitable for cleaning tools immediately after application.