Manufacturer Navigation
Our brands from A-Z
-
(191)
S & B Beschläge
-
(9)
Salamander
-
(5)
SCANSTRUT
-
(35)
Schatz
-
(3)
Scotch
-
(2)
Sea-Line
-
(14)
Seajet
-
(7)
SEASTAR SOLUTIONS
-
(45)
Secumar
-
(13)
Selden
-
(1)
Selma
-
(4)
Separ
-
(10)
SFC Energy AG
-
(2)
Sheffield
-
(8)
Shurflo
-
(12)
Sigma
-
(1)
Sigmar
-
(15)
Sika
-
(2)
Silentwind
-
(12)
Silva
-
(3)
SJÖ & HAV
-
(1)
Skotti
-
(11)
Skylotec
-
(5)
Solara
-
(2480)
Sonstige Hersteller
-
(13)
Sörensen
-
(28)
Spartan
-
(1)
Speedy Stitcher
-
(5)
SPUNFLEX
-
(12)
Stazo
-
(4)
Steiner
-
(7)
STELTON
-
(23)
Sterling
-
(3)
STIMPSON
-
(11)
Sundström
-
(2)
Sunnex
-
(2)
Superwind
Produkte von Sonstige Hersteller
Strong, sturdy coat hook with two arms made from brass with 4 screw holes.In the surfaces polished brass, chrom plated or matt chromed brass available.Weight: 170 g.
High performance microprismatic tape for maritime applications. Specifically designed for use in harsh environments which includes continuous immersion in sea water and extreme temperatures. Self adhesive with high holding strength.Width 5 cm.Comes loose by the meter.Also available in rolls of 45.7 m or as a pack of 6 single strips (please check "Suitable items"). Approved SOLAS / MED, permanently marked with shipswheel logo for immediate compliance identification.
These wick scissors are the ideal tool for trimming the wick of a paraffin lamp evenly.Made of nickel plated steel, angled handles.
NORSEMAN terminal, famed worldwide for decades! Made from 1.4401 stainless steel.The terminal dimensions are so large that it has a higher breaking load than the matching wire. These terminals can be attached to the wire onboard, without milling or pressing. Intended for 1 x 19 stainless steel wires and DYFORM. When the cone is replaced, the terminal can be reused. The standard design is usable for 1 x 19 wire. For 7 x 19 or 7 x 7 constructions, extra cones must be ordered!
Set of sleeve nut and pan head screw suitable for the plates and rosettes of the decorative yacht locks and yacht locks.Can also be used for fastening rudder tiller pins etc.Polished brass, chrome-plated brass or V2A finish.
Shaft anode for screwing onto the shaft, short form.Dimensions are nominal and may vary slightly.
Eyebolt with soldered ring, with collar and spherical head.Polished brass.Comes with nut and washer.
Classic wide-oval cowl vent made of soft PVC. White on the outside, red on the inside. Available in two sizes: with 76 mm (3") or 102 mm (4") air outlet.Supplied with a simple deck flange (outer diameter 125mm/150mm) made of white plastic with sealing cap. The lower end of the vent is pressed into the deck flange and snaps into place.
Navy blue cushion fenders with line running the whole way around. Nylon cover with stainless zipper which can be opened for cleaning the cover. Closed-cell foam will not absorb water.
Ear cup bumper for replacement on the NAUTIC TALK SL Bluetooth hands-free communication system or on the headset holder / single earhook with which the BUDDY CHAT Bluetooth helmet headset was supplemented.The defective ear bumper is quickly and easily removed from the headset holder and the replacement is clicked into place.
Rain repelling, semicircular cap of punched and polished plate stainless steel.Matches stainless steel louvre ventilator.
Sturdy handle with angled base plate made of heavy polished brass. Well suited for vertical mounting in the companionway, or elsewhere where a safe grip is required.
8-strand line, braided from high-tensile multifiber polypropylene, very soft and grippy, waterproof and absolutely decay-proof.Recommended as life ring attachment line, rescue throw line, etc.
Patented A4-stainless steel shackle that connects directly to a chain to relieve the strain on an anchor windlass or for similar uses.Bolt cannot be lost.
Brass snapshackle for halyards and sheets. Closes with spring bolt. With swivel, side opening.
Small cable clamp made from 1,5mm stainless steel sheet. For 10mm cable.
Grey plastic box with rubber cable entries and strip terminals.
Fibreglass antenna with practical mounting bracket, which can be used to continue operating the radio system on superstructures or stationary equipment in an emergency (after mast breakage or similar damage), for example.Permanently mounted cable (4.5 m long) with PL plug, which can be quickly connected to any stationary radio device.Supplied with cable in practical plastic bag.Antenna length 240 mm.
8-strand braided polypropylene line (PP)-split-fiber (smooth).Inexpensive cordage for many uses, waterproof and decay-resistant.Color: hemp-color.Available loose by the meter on a sliding price scale, in spools of 220 meters or in cut lengths up to 30 meters. Please order lengths divisible by 220 or 30 for the price discount.
