Manufacturer Navigation
Our brands from A-Z
-
(191)
S & B Beschläge
-
(9)
Salamander
-
(5)
SCANSTRUT
-
(35)
Schatz
-
(3)
Scotch
-
(2)
Sea-Line
-
(14)
Seajet
-
(7)
SEASTAR SOLUTIONS
-
(45)
Secumar
-
(13)
Selden
-
(1)
Selma
-
(4)
Separ
-
(10)
SFC Energy AG
-
(2)
Sheffield
-
(8)
Shurflo
-
(12)
Sigma
-
(1)
Sigmar
-
(15)
Sika
-
(2)
Silentwind
-
(12)
Silva
-
(3)
SJÖ & HAV
-
(1)
Skotti
-
(11)
Skylotec
-
(5)
Solara
-
(2480)
Sonstige Hersteller
-
(13)
Sörensen
-
(28)
Spartan
-
(1)
Speedy Stitcher
-
(5)
SPUNFLEX
-
(12)
Stazo
-
(4)
Steiner
-
(7)
STELTON
-
(23)
Sterling
-
(3)
STIMPSON
-
(11)
Sundström
-
(2)
Sunnex
-
(2)
Superwind
Produkte von Sonstige Hersteller
These accessories for SERVO-CLEAT sheet clamps, fit exactly to the respective clamp type. Available are fairleads and bases, as well as a bottom deck holder, which makes it possible to guide the sheet below deck without having to mount the clamp overhead.
Stainless-steel carabiner, material 1.4401 (AISI316).The joint on the closure is somewhat offset to create a larger opening.With closed eye and Key-Lock System.
Edge protection for lashing straps made from yellow plastic.Prevents damage and marks due to it's softly padded lower side.Easy to attach by latching to the tension belt.Available in two widths.
Straight wall bracket for ship's bells. Made from sand-cast brass. Finish either rolled and polished (unlacquered) or chromed. This straight holder is also well suited for lamps, etc. When used for a bell, the holder measurement "A" should be at least 0.6 x the bell's diameter.
Electrical and electronic components are often exposed to moisture on board, e.g. vapors, humidity, condensation, spray water, fog or rain. Liqui-Tech NAUTIC Spray reliably protects electrics and electronics from moisture-related failure, corrosion, oxidation and rust.Properties:infiltrates moisture and humidity 100 %leaves a permanent protective filmPreserves the electrical conductivity of treated partsas an insulating spray, prevents leakage currents and short circuitselectric current only flows where it is supposed to flowdoes not attack commercially available materialsdoes not damage windings or insulating paintsalso suitable for moving partsThe spray can be used directly when wet and remains fully effective at temperatures between +130°C and -80°C. Can be easily removed without leaving any residue (e.g. with brake cleaner).Application: Shake can well, spray on from a distance of 20-30 cm, wipe off residues with a dry cloth. Allow to act for at least 1 hour before use. Only use on devices that are not live - pull out the mains plug. Contents: 200g spray
Bracket for life rings, PFDs, or lifejackets.Stainless-steel bracket for attachment to the railing tube ∅ 19-33mm.Secured with a belt strap.
Brass tubing for a practical and decorative guard rail for the cabin table or for a shelf. This item is sold in several length
Pair of handles for ships locks with a four cornered shaft of 9 mm. Straight, thin design, made of brass, available die cast and handpolished or chromed. Deliverable for mortise or box locks.
Clean jute fabric, course weave.Weight approx. 320 g/m.sq., 120 cm wide.This cloth is necessary in rigging applications to parcel (process with impregnated fabric strips) a wire before it can be covered with thin rope.
Sign made of solid cast brass, cast gray with flat ground engraving areas. The sign has inscribed engraving fields and can be engraved on request with: Vessel name, home port, owner name, city of residence, street address and telephone. The engraving is not included in the price. We are happy to engrave the sign according to your specifications, the engraving must be ordered separately under item no. 3299-999 (see matching items). The production time for the engraving is about three weeks.
Rivet puller, round form. Thin professional tool for pulling copper disks on their corresponding rivets.Professional tool, made from hardened steel.To round off the rivet head you need the head maker 2291-...
On/off or selector switch with 4 stations for the optional interconnection of two batteries. Through overlapping contacts and safety interlocks, it can also be used for load switching.Max. capacity: 300 A (12 V for 10 sec.).Max. extended load at 12 volts: 150 A.Cord entrance from below.Dimensions: 135 x 135 x 73 mm.
Made from tool-grade steel. Hardened cutting edge (50 HRC), sharpened. Cutting edge, 75 mm, length 270 mm, height 65 mm.
Different accessoires and fittings for standard push-pull cables.Fit either Type 23 and 33 and RCS with 10-32 UNF thread.
Small polished cast brass latch with closed surface.Comes with striking plate.Practical latch that is totally flat on the outside.Yet the door can be opened easily with a push of a finger.Also available chromed.
Handle for carpenter's adze.The handle must be reworked and fit before use.
OECUSORB polypropylene oil-absorbant pads.The filling of these pads can absorb up to 25 times its weight in oil and other organic liquids.Simple to handle, hydrophobic, floating, reusable and easy to dispose of.This material is ideal for soaking up oil from the bilge, but also for many other tasks: protection of areas where oil or fuel could spill (for example, deck fills when fueling), water-polution control, cleaning machines, etc.The braided absorbent material is a plastic net bound on both sides with attachment loops; multiple pads can be connected to create an oil barrier.Dimensions: Length, approx. 60 cm; diameter, approx. 20 cm; weight, approx. 400 g.
Electropolished hinge with fixed stainless steel pin.With drawn edges.
Heavy stainless steel flush countersunk handle. Available in a simple design without spring or with a spring that holds the handle in the handle cup. Weight: 180 g.
Fire hose has long been recognised in commercial shipping as the most robust and effective abrasion protection for ropes.The hose is made of high-strength polyester fabric and is coated on the inside with EPDM rubber.The protective sleeve can be pulled onto the mooring eye before splicing. Available by the metre in your desired length.Colour: white with identification thread.
Beautiful, functional flag staff knob, cleanly turned from ash wood.With a cylindrical hole for the flag staff.With a polyaramid roller on the side for pennant halyard of 6 to 8 mm.The wood is untreated.
Polished brass, heavy design, for blunt enclosed doors.Straight design with brass pin and spacer ring, cast flaps.Right and left designs available.
