Primer

Black, quick-drying petro-resin solution (formerly: tar varnish) as a protective coating for ship hulls, pontoons and port facilities made of steel, wood and concrete.Can also be used underwater, but not indoors. The first coat can be diluted with 20-30 % turpentine substitute. If possible, apply at least two top coats, making sure that the first coat is completely dry beforehand.Technical DataSubstrate: iron, woodSurface preparation:Clean, dry, stable, frost-free surface; free from oil, grease, tar, and loose particlesDerust iron surfacesTopcoat: Additional 1–2 coats of after full dryingCoverage: approx. 8-10 m²/lThinner: turpentine substitute Application method: BrushDrying times at 10 °C: Not specified; apply only above +5 °C

EPIFANES CR Antifouling Primer is an aluminum-pigmented, universal underwater ship primer based on chlorinated rubber. Suitable for use on steel, aluminum, wood and polyester. It dries quickly and can be applied to many pre-treated substrates and old coatings. The chlorinated rubber contained in the primer makes it permanently elastic, allowing it to bridge the natural movement of wood, for example.

A single-component, fast-drying underwater primer based on vinyl with excellent water resistance and elasticity. The included aluminum flakes provide particularly good protection against corrosion and abrasion.The primer serves as a sealer on old antifouling or as a tie coat between epoxy primers kike HEMPEL LIGHT PRIMER (Art.No. 2577-055) and antifouling. Can be used on all boatbuilding materials. Application possible with roller, brush, pad, or airless spray.Technical DataSubstrates: GRP, wood, steel, existing primersPre-treatment: Wood: seal with suitable sealerGRP: sand, clean, remove dustSteel: high-pressure cleaning, sandblasting or mechanical rust removal, remove dustOld coatings: sand, clean, drySubsequent coat: Single-component antifoulingsCoverage: Approx. 7.8 m²/L at 50 µm dry film thicknessThinner: HEMPEL'S THINNER 811 (Art.No. 2577-026)Application method: Brush, roller, pad, airless spray (professional users)Drying times (at 20 °C): Dust dry after approx. 3 hrs, recoatable after min. 2.5 hrsFurther information on application can be found in the Technical Data Sheet under 'Downloads'.

The EPIFANES MULTI MARINE PRIMER is a universally applicable, fast-drying one-component primer with excellent adhesion properties. Suitable for use above the waterline on wood, fiberglass, steel, stainless steel, aluminum, galvanized metal, copper, and most other bare or painted substrates.The primer can also be used as a tie coat or adhesion promoter between a one- and two-component paint system.MULTI MARINE PRIMER offers exceptional coverage, high build, good pore filling, and corrosion protection on steel. Application note: Stir well before use. Do not apply coats wet-on-wet and observe the recoating intervals. For good adhesion between coats, sanding between each coat is recommended. Avoid overly thick coats when brushing to prevent drying problems. Must not be overcoated with epoxy products (filler, primer, paint).Technical DataSubstrates: GRP, hard plastics, wood, steel, aluminum, zinc, galvanized metals, existing one- and two-component coatingsSurface preparation:Gelcoat: degrease, sand dry P220–280Steel: degrease, sand dry P60Wood: degrease, sand dry P220–240Aluminum: degrease, sand dry P60; on new aluminum first apply 1 coat of EPIFANES WASHPRIMER AQOld coatings: clean, sand P240–280Subsequent coats: 1-C and 2-C paints and fillers (see data sheet)Coverage: approx. 8–10 m²/l at 45 µm dry film thicknessThinning: EPIFANES Paint Thinner (brush), EPIFANES 1-C Spray Thinner (spray gun), EPIFANES D-100 (airless)Application method: Brush, roller, spray gun, airless (professional users)Drying times at 10 °C: Dust dry after 2 hrs; recoatable after 12 hrs (1-C), after 48 hrs (2-C PU paints)Further information on application can be found in the Technical Data Sheet under "Downloads".

EPIFANES EPOXY PRIMER is a good filling, 2-component primer based on epoxy resin. It has very good adhesion to a wide range of substrates, is also a good filler and easy to sand. Has good anti-corrosion properties and is particularly resistant to under-rust in the event of damage. Suitable for underwater and above-water applications on steel, aluminum, GRP and plywood. Tips for application: No sanding is required within a recoating time of 24 hours. After 24 hours, intermediate sanding with P150-180 is recommended. Do not apply wet-on-wet to prevent runs and drying problems. Avoid application in direct sunlight or in excessive wind, as this leads to a rapid loss of solvent, which affects the flow. Technical DataSubstrate: Steel, aluminium, plywood, GRP/polyesterSurface preparation:Surfaces must be free from rust, grease, oil, wax and saltRinse with fresh water and pressure washer or emulsifierDegrease with ammonia solution, MEK or EPIFANES 1C Spray ThinnerTopcoat: Epoxy or polyurethane paints, e.g. EPIFANES Poly-urethane DD VarnishCoverage: approx. 10 m²/l Thinner: EPIFANES D-601Pot life at 15°C: 12 hrs.Application method: Brush, solvent-resistant roller, spray gun, airlessDrying times at 10 °C: Dust dry after approx. 1 hr; recoatable after 12 hrs; fully cured after 7 daysFurther information on applying  the product can be found in the technical data sheet under “Downloads”.

A proven underwater primer with good rust protection in the marine industry. This chlorinated rubber primer pigmented with aluminum is highly waterproof and elastic. It is suitable for steel, wood and GRP and can be overcoated with most commercially available antifoulings. PPG SIGMA VIKOTE 18 is also suitable as a sealer between an old and a new antifouling coat.After thorough cleaning and sanding, old tar and bitumen coatings can also be painted over, but “bleeding through” must be expected.Technical DataSubstrate: Steel, galvanized steel, shop-primed steel (e.g., with zinc silicate primer)Surface preparation:Steel: Blast clean to ISO-Sa2½, profile 40–70 µmAll surfaces must be dry and free from contamination and zinc saltsTopcoat: Antifoulings, e.g. SIGMA antifouling systemsCoverage: approx. 5.6 m²/l Thinner: THINNER 21-06 Application method: Brush, roller, airless or conventional spray (professional use)Drying times at 20 °C: Touch dry after 1 hr; recoatable after 6 hrsFurther information on processing can be found in the technical data sheet under “Downloads”.

EPIFANES POLYURETHANE PRIMER is a hard 2-component polyurethane primer. The primer has excellent adhesion properties, fills small pores and scratches and ensures a smooth surface for subsequent final coating with colored EPIFANES POLY URETHANE paint. The primer fills the substrate well, is easy to apply with a roller or brush and is easy to sand.Area of application: Interior and exterior above the waterline, on untreated GRP or gelcoat. The primer also adheres to existing 2-component polyurethane or epoxy coatings above the waterline.Technical DataSubstrate: Gelcoat, epoxy coatings, existing old  2-component coatingsSurface preparation:GRP/Gelcoat: degrease, sand with P180Epoxy (HB/Primer): degrease, sand with P120–P180Old coatings: degrease, sand with P180–P220New aluminium: apply one coat of EPIFANES WASHPPRIMER AQTopcoat: EPIFANES Poly-urethane Varnish, for other paints see technical data sheetCoverage: approx. 10 m²/l at 35 µm dry film thicknessThinner: EPIFANES Poly-urethane Brush Thinner / Spray ThinnerApplication method: Brush, roller, spray gun (professional use)Drying times at 10 °C: Dust dry after 2 hrs; recoatable after 12 hrsFurther information on applying this product can be found in the technical data sheet under “Downloads”

HEMPEL LIGHT PRIMER is a high-quality 2-component epoxy primer for applications below and above the water. It can be used on rigid substrates as a barrier against penetrating water vapor, on GRP for osmosis prevention and repair, and on metal surfaces as corrosion protection. It can also be used on plywood and hardwood. Very suitable as an adhesion promoter for top coats and antifouling. Technical DataSubstrate: GRP, plywood, steel, aluminium, existing coatingsSurface preparation:GRP: sand, cleanPlywood: seal with suitable sealerSteel: high-pressure fresh water wash, sandblast or mechanically remove rust and cleanAluminium: non-metallic abrasive blasting, degreaseOld coatings: sand, clean, dryPorous surfaces: prime first coat of Light Primer with 20% thinnerTopcoat: standard 1K and 2K products (see data sheet)Coverage: 8.2 m²/l at 60 µm dry film thicknessThinner: HEMPEL'S THINNER 845 (Art.No. 2577-022)Application method: Brush, roller, airless spray (professional use)Drying times at 10 °C: Dust dry after 6 hrs; recoatable after 9 hrsFurther information on application can be found in the technical data sheet under “Downloads”.

A solvent-based, single-component polyurethane resin that is excellent as a bonding primer for laminates with epoxy or polyester coatings. VOSSCHEMIE PAINT SYSTEM G4 Extra cures by releasing solvents and cross-links by absorbing moisture from the air and the substrate. This creates a wear-resistant film with high impact strength.As a binder for wood flour, G4 Extra can also be used to make wood filler for filling chips and wind cracks. It is also suitable for durable sealing of dark woods (e.g. mahogany). The coating has a yellowish-transparent tint that is intensified under UV exposure. Improved UV protection is provided by VOSSCHEMIE polyurethane varnish G8 SUPER. Not suitable for use in interior areas (e.g. cabin).Technical DataSubstrates: Wood, concrete, steel, GRPSubsequent coating: 1K or 2K PUR coatings, GRP laminatesCoverage: approx. 0.1 l/m² (non-absorbent substrates), 0.2–0.25 l/m² (absorbent substrates)Thinning: noneApplication method: Brush, lambskin roller, spray gun (professional users, only with respiratory protection!)Drying times at 20 °C: recoatable with itself: 2–4 hrs (as soon as substrate is tack-free), max. 12 hrs. GRP: 0.5–4 hrs (tacky)Note: Product contains hazardous chemicals according to REACH regulation. We recommend processing only by commercial users. Contains isocyanates. may cause allergic reactions. From August 24, 2023, appropriate training must be completed prior to industrial or commercial use. Further information can be found in the Technical or Safety Data Sheet under 'Downloads'.

Zinc dust-containing (67%), surface-tolerant 2-component epoxy primer with high penetration properties, even on steel surfaces that have only been derusted by hand or water-blasted. The pigment-rich formulation results in a very well adhering and robust cathodic corrosion protection layer for use above and below water.HANSAZINC ST tolerates residual moisture (no wetness) and slight flash rust formation. Can be painted over with two-component paints as well as with bitumen, vinyl and chlorinated rubber primers, but not with alkyd resin-based paints and paints containing zinc phosphate. Not suitable for use on galvanized, stainless, light or non-ferrous metals, wood, mineral substrates or plastics.Application: The mixing ratio is 93:7 (base:hardener) by volume. The pot life is 3-4 hours. Depending on the substrate, the product can be applied by spraying, brushing or rolling. On hand-rusted surfaces, the coating must be worked in intensively; a bristle brush is best suited for this. Ideal processing and surface temperatures are between 15 °C and 25 °C and at least 5 °C above the dew point.&nbsp

A low-solvent, two-component thick film primer based on epoxy resin with zinc phosphate.Ideal as corrosion protection on steel and aluminum, as an osmosis protection layer on GRP and for sealing wood.The primer dries quickly and allows fast build-up of layers due to the higher solids content. Applicable above and below the waterline. For first time application, it is recommended to paint four coats to achieve optimum water impermeability. Can also be used for maintaining existing two-component systems. If the surface is to be painted with an antifouling, a coat of an adhesion primer such as EPIFANES INTERIMCOAT is required.Yield approx. 10 m²/l.Technical DataSubstrate: GRP, steel, plywood, aluminium, old coatingsSurface preparation:Steel: remove rust, degrease, sand P60–80GRP: degrease with Epifanes Polyester Degreaser, sand P240Aluminium: apply 1 coat Epifanes Washprimer AQOld coatings: clean, sand P180–220, degrease with Epifanes Spray ThinnerFollow-up coat: Epifanes Epoxy Primer, Poly-urethane Primer, Interimcoat + antifouling, Poly-urethane Yacht CoatingCoverage: approx. 6 m²/l at 85 µm dry film thicknessThinner: EPIFANES D-601 Epoxy Thinner Application method: Brush, roller, airless or conventional spray (professional use)Drying times at 15 °C: Dust dry after 3 hrs, recoatable after 10 hrs, sandable after 36 hrsFurther information on processing can be found in the technical data sheet under “Downloads”.

Primer from HEMPEL specially developed for the pretreatment of ship propellers and outboard motors for spraying.The PROP Primer allows easy application of thin coat thicknesses and is fast drying. For the best possible corrosion protection and adhesion primer before painting antifouling such as HEMPEL ECOPOWER PROP.Suitable for: GRP, steel and other metals. Suitable cleaner: HEMPELs Thinner 845 Color: Light grayTheoretical coverage: approx. 6.6 m²/LNote: Please observe the application instructions in the technical data sheet before and during application.

A two-component epoxy vinyl-based primer that can be used above and below the waterline.The coarse surface structure ensures good mechanical adhesion, thus eliminating the need for sanding before the next coating. Can be painted over with all EPIFANES one- and two-component products. Suitable as an adhesion primer for antifoulings.Note: Before painting over the product with antifouling, wipe the surface thoroughly after the recommended drying time with a cleaning agent such as EPIFANES cleaning thinner, white spirit or water to remove any amino red from the surface. Then allow to evaporate. If antifouling is to be applied after seven days, degrease EPIFANES INTERIMCOAT+ with EPIFANES Cleaning Thinner and, if necessary, lightly sand with P150 - P180.Technical data Substrates: primed surfaces (epoxy systems), gelcoatPre-treatment: Polyester gelcoat: degrease, sand with P240 Epoxy systems: degreased, sanded with P60-80Subsequent coating: Standard one- or two-component productx, antifouling coatings (e.g. EPIFANES Copper Cruise, EPIFANES Foul-Away)Coverage: approx. 8 m²/kg (theoretical)Thinner: EPIFANES D-601 ThinnerApplication method: Brush, fur roller, spray gun (only with respiratory protection!) Mixing ratio: 100 : 25 (vol.), 100 : 14 (wt.)Pot life at 15°C: 3-4 hours, induction time approx. 10-15 min. Drying times at min. 12 °C: Dust dry: approx. 4 hours; can be painted over: 18 hrs - 14 daysFurther information on applying this product can be found in the technical data sheet under “Downloads”.

Premium primer that combines the properties of a rust protection primer and an air-drying natural oil with high solids content and exceptional penetrating properties. Thanks to the formulation with OWATROL oil, OWATROL CIP has a low surface tension and is three times "wetter" than water. This allows it to optimally wet surfaces and penetrate even hard-to-reach corners that may not be mechanically derusted. It penetrates thick rust layers down to the "sound" metal and displaces moisture and air.The oil dries completely, even in thick layers given sufficient drying time. After drying, it remains elastic but is hard enough due to the added primer to be coated with a subsequent one- or two-component system such as an epoxy or chlorinated rubber primer. Suitable for all areas exposed to extreme climatic conditions, such as ballast tanks. Active ingredients: water-displacing penetrating oil and iron oxide.Technical DataSubstrate: Iron, steel, cast iron, stainless steel, light metals (bare or rusted)Surface preparation:Remove loose paint and rustFirm rust may remainSurface must be dry, grease-free and cleanFor chemically exposed surfaces: thorough cleaning with water or steamTopcoat: All one- or two-component systems including epoxy, polyurethane, chlorinated rubber etc.Coverage: up to 15 m²/l (depending on substrate and rust depth)Thinner: noneApplication method: Brush, lambskin roller, spray gun (professional use)Drying times at 20 °C: Touch dry after approx. 6 hrs; recoatable after 48 hrs.Further information on applying this product can be found in the technical data sheet under “Downloads”.Safety note: Cloths soaked with drying oils can self-ignite, therefore always spread out to dry before disposal or collect in sealed metal containers.

This very fast-drying universal epoxy primer is "one for all": an exceptionally robust and waterproof 2-component sealer for all boat building materials under and above water.PPG SIGMA PRIME 200 has excellent corrosion protection properties as well as high surface and temperature tolerance. It also adheres to hand-rusted and water-blasted surfaces, as well as to aluminium and hot-dip galvanized surfaces. For good corrosion protection, we recommend applying at least 4-5 coats by roller.Can be painted over with all maritime 1- and 2-component primers, paints and varnishes. An adhesion promoter (tiecoat) is required before painting with antifouling. SIGMA VIKOTE 18 is used for repairs and smaller ships. SIGMA COVER 555 (only available on request in 20 liter containers) is recommended for large-area coatings.Tip: VIKOTE 18 can be painted directly onto SIGMAPRIME 200 without sanding if the surface is not yet fully cured, i.e. "tacky". Otherwise, intermediate sanding is necessary.Technical dataSubstrates: Steel, galvanized steel, store primer, coated metalsPre-treatment:Steel: blasting according to ISO-Sa2½ or machine cleaning (SPSS-Pt3), blasting profile 30-75 µmStore primer: leave intact or blast clean if damagedGalvanized steel: degrease, roughen with sandpaper or sweep blastingOld coatings: High-pressure cleaning, dry, clean, free of dust and greaseFollow-up coat: 2-component epoxy resins and polyurethanes (e.g. SIGMACOVER, SIGMADUR)Coverage: approx. 7.6 m²/l at 75 µm,Dilution: THINNER 91-92 (brush/roller: up to 5 %, spraying: 0-15 %)Application method: Brush, roller, airless or air sprayingMixing ratio: 4:1 (base:hardener by volume)Pot life: 7 hours at 20 °CDrying times at 20 °C: Dust-dry after 1.5 hours, touch-dry after 4 hours, fully hardened after 7 daysFurther processing information can be found in the technical data sheet under "Downloads".

SEAJET 015 UNDERWATER PRIMER is a quick-drying, one-component primer for underwater use with good water resistance, corrosion protection and very good adhesion to all substrates (except aluminum).Due to the special binder, it is also ideally suited as an adhesion promoter and barrier primer on unknown and incompatible antifoulings.This also expressly applies to coatings on TEFLON and PTFE-containing antifoulings.Technical dataSubstrates: GRP, wood, existing antifouling coatingsPre-treatment: Existing antifouling coatings: Sand the surface with P100-120 (wet sanding). Apply 1 coat &nbsp

HEMPEL CONVERSION Primer is a two-component epoxy resin-based adhesion primer. It was developed to facilitate the change from conventional antifoulings to the biocide-free thin-film antifouling HEMPASPEED TF from HEMPEL. The primer can be applied to existing antifoulings (including International VC-17m) as well as to one- and two-component primers, provided the surface is intact and stable. Caution: The primer does NOT provide corrosion protection, but merely acts as an adhesion promoter. Prime uncoated surfaces with a corrosion protection primer beforehand. Two-component primers based on epoxy resin (e.g. HEMPEL Light Primer) are recommended. Technical DataSubstrate: Existing antifouling in good condition (not suitable for bare surfaces)Surface preparation:Wet sand old antifouling with water and waterproof paperRinse with fresh water, clean and allow to drySurface must be clean, dry and free of greaseTopcoat: HEMPEL's Silic One Tiecoat, Hempaspeed TFCoverage: approx. 15 m²/l at 25 µm dry film thicknessThinner: Do not thinApplication method: Brush, roller Mixing ratio: 3:1 (Base:Hardener by volume)Pot life: 8 hrs at 20 °CDrying times at 20 °C: Dust dry after 1¼ hrs; recoatable after 2 hrs (Silic One Tiecoat), 30 min (Hempaspeed TF); fully cured after 7 daysFurther information on processing can be found in the technical data sheet under “Downloads”.

EPIFANES BLACK BOTTOM flexible bitumen-based protective coating for the area above and below the waterline.This modern version of the so-called black varnish adheres well to raw steel and wood surfaces as well as existing tar and bitumen layers and synthetic primers. It is easy to apply, offers high UV resistance, elasticity and protection against the changing influences of water and air.Note: It is recommended to apply the first layer with 15-25% with EPIFANES 1K-Spraythinner and use a stiff brush to work the paint onto the surface. For effective corrosion protection on new hulls, apply at least 250-300 μm to the raw substrate in the underwater area. Technical DataSubstrate: Steel, wood, existing tar coatings (repair/maintenance)Surface preparation:Clean, dry, degreased, well-sanded surface, free of rust, dust and adhesionDegrease with EPIFANES 1K Spray Thinner; rinse off water-soluble residues with fresh waterFollow-up coat: Overcoatable with EPIFANES Copper-Free AntifoulingCoverage: approx. 10 m²/l at 50 µm dry film thicknessThinner:Brush: EPIFANES Brush ThinnerSpray: EPIFANES Spray Thinner for 1C lacquers and primersAirless: EPIFANES D-100Application method: Brush, roller, conventional spray gun, airless sprayDrying times at 20 °C: Dust dry after 2 hrs, recoatable after 12 hrsFurther information on applying this product can be found in the technical data sheet under “Downloads”.

Universally applicable and economical two-component epoxy-based primer for all boat-building materials (except hard-working solid wood).The YACHTCARE epoxy primer is diffusion-tight with the appropriate layer thickness (6 layers) and is ideal as an osmosis protection coating on GRP yachts and as corrosion protection on steel and aluminum. It also has excellent adhesion properties on aluminum.The primer can be painted over with all antifoulings and paint systems.Technical dataSubstrates: GRP, rigid wood, steel, aluminumPre-treatment: The substrate must be clean, dry and free of grease. All incompatible old coatings (1-component systems, antifoulings etc.) must be completely removed before applying the primerApplication: Apply in dry weather and at temperatures between 10°C and 30°C. Number of coats for new construction: 2-3, for better corrosion and osmosis protection at least 6 coats are better.

The LEFANT Epoxy Primer is specially designed for underwater use and can be applied to gelcoat, plastic, steel, aluminum, Z-drives and propellers. The two-component epoxy resin-based primer is suitable for the pre-treatment of antifoulings such as LEFANT T-Coat, it is oil and chemical resistant, protects the hull against the penetration of moisture and thus prevents osmosis. Thanks to the long overcoating intervals, it is easy to apply and cures even at low temperatures (min. 5 °C). Available in white or black.Application on painted substrates: Old one-component coatings and primers should be removed, two-component primers in good condition can be roughly sanded (grain size 60-80). Then clean thoroughly. If necessary, level out uneven areas with epoxy filler.When recoating steel hulls, the surface should be sandblasted or roughly sanded and painted with a thinned coat of epoxy primer (20-30% thinned with Lefant Multi-Thinner) immediately after sanding. Then apply up to three further coats and level out any unevenness and imperfections with filler.Technical DataSubstrate: GRP, steel, aluminium, plywood, existing 2C epoxy primersSurface preparation:GRP: remove release agents, sand (grit 80), degreaseSteel/aluminium: sandblast or sand (grit 40/80), degreaseWood: sand (grit 80), cleanExisting primer: sand (grit 80), cleanFollow-up coat: LEFANT antifoulingsCoverage: approx. 8 m²/l at 50 µm, 2 m²/l at 200 µm, 1.33 m²/l at 300 µmThinner: LEFANT Multi Thinner 3087 (only for first coat on metal or spray application)Application method: Short mohair roller, spray (professional use)Mixing ratio: 4:1 (Base:Hardener by volume)Pot life: 8 hrs at 20 °CDrying times at 18 °C: Recoatable after 12 hrs, antifouling after 3–5 days (depending on temperature/system), fully durable after 7 daysFurther information on processing can be found in the technical data sheet under “Downloads”.

WERDOL Primer Paint is a one-component, traditional primer for use on untreated wood. Good filling and covering properties for interior and exterior use. Suitable as a primer for one-component paint systems above the waterline. Can be overcoated with all EPIFANES one-component color paints.Technical DataSubstrate: Wood (above the waterline, interior and exterior)Surface preparation:Wood moisture max. 15–17 %Degrease oily wood with EPIFANES 1C Spray Thinner or special benzineSand with grit 60–80 along the grain, then with 100–220Remove sanding dust thoroughlyTopcoat: One-component alkyd-resin based paints Coverage: approx. 12 m²/l Thinner: EPIFANES Brush Thinner (brush/roller), EPIFANES 1C Spray Thinner (spray), EPIFANES D-100 (airless)Application method: Brush, roller, spray gun (professional use)Drying times at 20 °C: Dust dry after 2 hrs; recoatable after 24 hrsFurther information on processing can be found in the technical data sheet under “Downloads”.

EPIFANES RUST REMOVER is an acid-free rust converter based on water-displacing polymers that stops the rusting process. Provides a good primer for 1- and 2-component primers and paints above and below water. Before application, degrease the substrate and remove any loose rust, then apply only a thin layer.Important: RUST REMOVER is not a substitute for a primer and should be painted over within a minimum of 3 hours and a maximum of 48 hours (18°C).Technical dataSubstrates: Hand-rusted steel above and below the waterlinePre-treatment:Remove loose rust mechanically (e.g. with a wire brush or coarse sandpaper)Thoroughly degrease the substrate (e.g. with EPIFANES cleaning thinner)Follow-up coat: All 1K and 2K primers, paints and coatingsCoverage: approx. 20 m²/l with thin applicationDilution: Do not diluteApplication method: BrushDrying times at 18 °C: Can be painted over after at least 3 hours, at the latest after 48 hours.

The SEAJET 117 Multipurpose Epoxy Primer is a two-component primer for above and underwater use that is easy to apply and dries quickly. The ideal barrier layer to prevent water damage in underwater areas. Four coats provide good osmosis protection for GRP hulls and corrosion protection for steel or aluminum hulls. The primer can be painted over with two-component and one-component products.&nbsp

EURO LOCK Zinc Dust Paint offers high-quality corrosion protection for all metals, with a zinc content of approx. 95 % in the dry film. Suitable for touching up galvanized anchors, anchor chains and for repairing welding and sheet metal work (electrically conductive during welding). Prevents rust and offers good protection against extreme weather conditions. Temperature resistant up to 500 °C. Suitable as a single coating or as a primer for further top coats on systems exposed to water and weathering.&nbsp