EPIFANES POLY-URETHANE Primer

The EPIFANES MULTI MARINE PRIMER is a universally applicable, fast-drying one-component primer with excellent adhesion properties. Suitable for use above the waterline on wood, fiberglass, steel, stainless steel, aluminum, galvanized metal, copper, and most other bare or painted substrates.The primer can also be used as a tie coat or adhesion promoter between a one- and two-component paint system.MULTI MARINE PRIMER offers exceptional coverage, high build, good pore filling, and corrosion protection on steel. Application note: Stir well before use. Do not apply coats wet-on-wet and observe the recoating intervals. For good adhesion between coats, sanding between each coat is recommended. Avoid overly thick coats when brushing to prevent drying problems. Must not be overcoated with epoxy products (filler, primer, paint).Technical DataSubstrates: GRP, hard plastics, wood, steel, aluminum, zinc, galvanized metals, existing one- and two-component coatingsSurface preparation:Gelcoat: degrease, sand dry P220–280Steel: degrease, sand dry P60Wood: degrease, sand dry P220–240Aluminum: degrease, sand dry P60; on new aluminum first apply 1 coat of EPIFANES WASHPRIMER AQOld coatings: clean, sand P240–280Subsequent coats: 1-C and 2-C paints and fillers (see data sheet)Coverage: approx. 8–10 m²/l at 45 µm dry film thicknessThinning: EPIFANES Paint Thinner (brush), EPIFANES 1-C Spray Thinner (spray gun), EPIFANES D-100 (airless)Application method: Brush, roller, spray gun, airless (professional users)Drying times at 10 °C: Dust dry after 2 hrs; recoatable after 12 hrs (1-C), after 48 hrs (2-C PU paints)Further information on application can be found in the Technical Data Sheet under "Downloads".

EPIFANES POLYURETHANE PRIMER is a hard 2-component polyurethane primer. The primer has excellent adhesion properties, fills small pores and scratches and ensures a smooth surface for subsequent final coating with colored EPIFANES POLY URETHANE paint. The primer fills the substrate well, is easy to apply with a roller or brush and is easy to sand.Area of application: Interior and exterior above the waterline, on untreated GRP or gelcoat. The primer also adheres to existing 2-component polyurethane or epoxy coatings above the waterline.Technical DataSubstrate: Gelcoat, epoxy coatings, existing old  2-component coatingsSurface preparation:GRP/Gelcoat: degrease, sand with P180Epoxy (HB/Primer): degrease, sand with P120–P180Old coatings: degrease, sand with P180–P220New aluminium: apply one coat of EPIFANES WASHPPRIMER AQTopcoat: EPIFANES Poly-urethane Varnish, for other paints see technical data sheetCoverage: approx. 10 m²/l at 35 µm dry film thicknessThinner: EPIFANES Poly-urethane Brush Thinner / Spray ThinnerApplication method: Brush, roller, spray gun (professional use)Drying times at 10 °C: Dust dry after 2 hrs; recoatable after 12 hrsFurther information on applying this product can be found in the technical data sheet under “Downloads”

EPIFANES RUST REMOVER is an acid-free rust converter based on water-displacing polymers that stops the rusting process. Provides a good primer for 1- and 2-component primers and paints above and below water. Before application, degrease the substrate and remove any loose rust, then apply only a thin layer.Important: RUST REMOVER is not a substitute for a primer and should be painted over within a minimum of 3 hours and a maximum of 48 hours (18°C).Technical dataSubstrates: Hand-rusted steel above and below the waterlinePre-treatment:Remove loose rust mechanically (e.g. with a wire brush or coarse sandpaper)Thoroughly degrease the substrate (e.g. with EPIFANES cleaning thinner)Follow-up coat: All 1K and 2K primers, paints and coatingsCoverage: approx. 20 m²/l with thin applicationDilution: Do not diluteApplication method: BrushDrying times at 18 °C: Can be painted over after at least 3 hours, at the latest after 48 hours.

Water-based adhesion primer based on acrylate resin for hard-to-adhere substrates such as aluminum, galvanized steel, non-ferrous metals, stainless steel, glass or ceramics. EPIFANES WASHPRIMER AQ is suitable for use in one- and two-component systems, above and below the waterline, indoors and outdoors. Application: Thoroughly clean the substrate, remove salt, grease, oil, and zinc salts. Keep the surface dry and free of corrosion. Apply evenly with a brush, air spray, or airless spray. Do not sand the layer. Can be painted over with all 1-component and 2-component paints, subject to the application of alkyd resin paints on zinc, due to the possible migration of fatty acids from the binder and zinc soap formation through reaction during prolonged contactApplication area: Adhesion primer for aluminum, galvanized steel, non-ferrous metals, stainless steel, glass, ceramics; above and below the waterlineSubstrate: Free of salt, grease, oil, and corrosion; thoroughly cleaned and dryCoverage: Approx. 18 m²/L at 10 µm dry film thicknessThinning: Not requiredSubsequent coating: all common 1K and 2K paintsApplication method: Brush, air spray, airless sprayDrying times (at 20 °C): Touch dry after 15 min., recoatable after min. 2 hrs to max. 14 daysFor more information on application, refer to the Technical Data Sheet under 'Downloads'.

WERDOL Primer Paint is a one-component, traditional primer for use on untreated wood. Good filling and covering properties for interior and exterior use. Suitable as a primer for one-component paint systems above the waterline. Can be overcoated with all EPIFANES one-component color paints.Technical DataSubstrate: Wood (above the waterline, interior and exterior)Surface preparation:Wood moisture max. 15–17 %Degrease oily wood with EPIFANES 1C Spray Thinner or special benzineSand with grit 60–80 along the grain, then with 100–220Remove sanding dust thoroughlyTopcoat: One-component alkyd-resin based paints Coverage: approx. 12 m²/l Thinner: EPIFANES Brush Thinner (brush/roller), EPIFANES 1C Spray Thinner (spray), EPIFANES D-100 (airless)Application method: Brush, roller, spray gun (professional use)Drying times at 20 °C: Dust dry after 2 hrs; recoatable after 24 hrsFurther information on processing can be found in the technical data sheet under “Downloads”.

WERDOL Bleimennige is a traditional, rust-preventing primer based on a modified linseed oil alkyd resin and a mixture of lead and iron oxide. Provides excellent rust protection on steel and has a rot-preventive effect on untreated wood. Nowadays it is mainly used for restoration work, as the lead oxide it contains is harmful to health and toxic to reproduction. Not suitable for use under water.This product may only be shipped to resellers, professional users and public research and teaching institutions in accordance with the Chemicals Prohibition Ordinance. Are you one of these customers? Then send us your inquiry here with a corresponding user certificate. We will be happy to provide you with a quotation.Technical dataSubstrates: Steel, iron, wood (above the waterline)Pre-treatment:Surface must be clean, dry and free of greaseRemove loose layers of rust and paintSubsequent coat: Single-component alkyd resin paints (e.g. EPIFANES boat paint, WERDOL Coasterlak)Coverage: approx. 12 m²/l with 50 µm dry film thicknessThinner: EPIFANES paint thinnerApplication method: Brush, rollerDrying times at 18 °C: Recoatable after 12 hours.Note: Contains lead. Do not use for painting objects that could be chewed or sucked by children. Contains cobalt carboxylate. May cause an allergic reaction.

Cathodic protecting zinc compound on the basis of polystyrene resin for rust free steel (by hand or machine) above the waterline or for zinc coated surfaces.More than 90% pure zinc in the drying coat.Yield: approx. 6 sq.m/l.

The Zinc Spray from EURO LOCK offers a fast-drying corrosion protection with excellent long-term effect for all metals. It is suitable for use on thermally stressed parts such as intake manifolds, heat exchangers, oil coolers, etc. It is electrically conductive and heat resistant up to 500 °C.Additionally, it is suitable for reworking or repairing defects on hot-dip galvanized parts, and for touching up damaged zinc coatings.Also suitable for refreshing galvanized anchors, anchor chains, and for repairing welding and sheet metal work. Prevents rust and provides good protection against extreme weather conditions. Zinc content approx. 95% in the dry film. Can be overpainted with most one- and two-component primers and paints.Technical DataSubstrates: All metalsPretreatment:Surface must be clean, dry, free of grease and oilShake can well for approx. 2 minutes before useTest spraying recommendedSubsequent coating: Can be overpainted with many paint systems (own testing recommended)Coverage: No informationApplication method: Spray from approx. 20–30 cm distance in a crisscross patternDrying times at 20 °C: Dust-dry after approx. 8 min; tack-free after 20–30 min; fully dry after 48 hrsFurther information on application can be found in the technical data sheet under "Downloads".

A solvent-based, one-component polyurethane resin that is ideal as an adhesive primer for laminates with epoxy or polyester coatings. PAINT SYSTEM G4 Extra cures by releasing solvents and cross-links by absorbing moisture from the air and the substrate. This creates a wear-resistant film with high impact resistance.As a binder for wood flour, G4 Extra can also be used for the production of wood filler to fill chippings and wind cracks. It is also suitable as a hard-wearing sealant for dark woods (e.g. mahogany). The coating has a yellowish-transparent coloration, which is intensified when exposed to UV light. VOSSCHEMIE Polyurethane Varnish G8 SUPER offers improved UV protection. Not suitable for indoor use (e.g. cabin).Technical dataSubstrates: Wood, concrete, steel, GRPSubsequent coats: 1K or 2K PUR coatings, GRP laminatesCoverage: approx. 0.1 l/m² (non-absorbent substrates), 0.2-0.25 l/m² (absorbent substrates)Dilution: noneApplication method: Brush, fur roller, spray gun (professional users, only with respiratory protection!)Drying times at 20 °C: can be painted over with itself: 2-4 hours (as soon as substrate is tack-free), max. 12 hours GRP: 0.5-4 hours (tacky)Note: Contains isocyanates. We recommend processing only by professional users. May cause allergic reactions. Appropriate training must be provided for commercial use. The technical or safety data sheets under 'Downloads'.

HEMPEL LIGHT PRIMER is a high-quality two-component primer based on epoxy resin for underwater and above-water applications. It serves as a good barrier against penetrating water vapor on rigid substrates, for osmosis prevention and repair on GRP and as corrosion protection on metals. It can also be used on plywood and hardwood. Suitable for interior and exterior use above and below the waterline, as well as for coating keels and rudders.Within the specified recoating intervals, LIGHT PRIMER can also be recoated directly with a subsequent product without intermediate sanding. The surface should be almost dry, but still slightly tacky. For a subsequent coat of antifouling, a coat of HEMPEL UNDERWATER PRIMER (Art. No. 2577-053) is recommended as an adhesion primer.Technical dataSubstrates: GRP, plywood, steel, aluminum, existing coatingsPre-treatment:GRP: sand, clean, remove dustPlywood: seal with a suitable sealerSteel: high-pressure cleaning, sandblasting or mechanical rust removal, dust removalOld coatings: sand, clean, dryPorous surfaces: prime first coat of Light Primer with 20% thinnerSubsequent coat: standard 1K and 2K products (see data sheet)Coverage: 8.2 m²/l at 60 µm dry film thicknessThinner: HEMPEL'S THINNER 845 (Art. No. 2577-022)Application method: Brush, roller, airless spraying (professional users)Drying times at 10 °C: Hand dry after 6 hours; recoatable after 9 hours.Further information on application can be found in the technical data sheet under "Downloads".

Premium primer that combines the properties of a rust protection primer and an air-drying natural oil with high solids content and exceptional penetrating properties. Thanks to the formulation with OWATROL oil, OWATROL CIP has a low surface tension and is three times "wetter" than water. This allows it to optimally wet surfaces and penetrate even hard-to-reach corners that may not be mechanically derusted. It penetrates thick rust layers down to the "sound" metal and displaces moisture and air.The oil dries completely, even in thick layers given sufficient drying time. After drying, it remains elastic but is hard enough due to the added primer to be coated with a subsequent one- or two-component system such as an epoxy or chlorinated rubber primer. Suitable for all areas exposed to extreme climatic conditions, such as ballast tanks. Active ingredients: water-displacing penetrating oil and iron oxide.Technical DataSubstrate: Iron, steel, cast iron, stainless steel, light metals (bare or rusted)Surface preparation:Remove loose paint and rustFirm rust may remainSurface must be dry, grease-free and cleanFor chemically exposed surfaces: thorough cleaning with water or steamTopcoat: All one- or two-component systems including epoxy, polyurethane, chlorinated rubber etc.Coverage: up to 15 m²/l (depending on substrate and rust depth)Thinner: noneApplication method: Brush, lambskin roller, spray gun (professional use)Drying times at 20 °C: Touch dry after approx. 6 hrs; recoatable after 48 hrs.Further information on applying this product can be found in the technical data sheet under “Downloads”.Safety note: Cloths soaked with drying oils can self-ignite, therefore always spread out to dry before disposal or collect in sealed metal containers.

Zinc dust-containing (67%), surface-tolerant 2-component epoxy primer with high penetration properties, even on steel surfaces that have only been derusted by hand or water-blasted. The pigment-rich formulation results in a very well adhering and robust cathodic corrosion protection layer for use above and below water.HANSAZINC ST tolerates residual moisture (no wetness) and slight flash rust formation. Can be painted over with two-component paints as well as with bitumen, vinyl and chlorinated rubber primers, but not with alkyd resin-based paints and paints containing zinc phosphate. Not suitable for use on galvanized, stainless, light or non-ferrous metals, wood, mineral substrates or plastics.Application: The mixing ratio is 93:7 (base:hardener) by volume. The pot life is 3-4 hours. Depending on the substrate, the product can be applied by spraying, brushing or rolling. On hand-rusted surfaces, the coating must be worked in intensively; a bristle brush is best suited for this. Ideal processing and surface temperatures are between 15 °C and 25 °C and at least 5 °C above the dew point.Technical dataArea of application: 2-component EP corrosion protection primerSubstrates: Steel, sheet steel, gray cast ironPre-treatment:Blasting Sa 2½Pressure water blasting DW 3Manual rust removal St 2Follow-up coats (observe system structure):2-component epoxy primer HANSAPOX Barrier (Art. No. 2670-202), then HANSA Vinyl-Primer (Art. No. 2671-202)or: 2K epoxy primer SIGMA PRIME 200 (Art. No. 2591-104), followed by SIGMA Vikote 18 (Art. No. 2580-120)Coverage: approx. 8 - 11.2 m²/l (depending on layer thickness)Mixing ratio: 93:7 (base:hardener, by volume)Thinner: HANSASOL EP thinner (Art. No. 2670-991)Application method: Brushing, rolling, spraying (professional application)Pot life at 23°C: approx. 3-4 hoursDrying times at 23 °C: dust-dry after 2 hours; can be painted over with subsequent products without intermediate sanding after 4 hours, cured after approx. 14 daysFurther information on processing the product can be found under "Downloads".

SEAJET 117 Multipurpose Epoxy Primer is a two-component primer based on epoxy resin in spray form, which is particularly suitable for small spot repairs. The product is especially abrasion-resistant and serves as a barrier coat against water exposure in underwater areas as well as a robust primer for 2-component paints in above-water areas.  Application: The substrate should be free of contaminants; depending on the substrate, the surface should be sanded before application. Shake the spray can for at least 2 minutes before use. Then the hardener is activated via the valve at the bottom of the can and the can is shaken again for 2 minutes. Ensure good ventilation during processing, do not inhale spray mist, and wear suitable protective gloves as well as eye/face protection. Keep away from heat, sparks, and open flames. Technical dataArea of application: Barrier coat in underwater areas; primer for 2-component paints in above-water areas. Substrate: GRP, gelcoat, steel, aluminumSubsequent coating: Antifouling coating or 2-component paintsApplication method: Spray can; in the system also airless spray, brush, rollerFurther information on processing can be found in the technical data sheet under 'Downloads'.

Two-component epoxy primer for steel with excellent adhesion properties. PPG SIGMACOVER 280 is an aluminum-pigmented, polyamide-cured universal primer that adheres to steel, shop primers, galvanized steel, and non-ferrous metals.Suitable as a sealer or adhesion primer, for use in ballast tanks, and for repair of weld seams and damage to epoxy coatings. Can be overcoated with most alkyd, chlorinated rubber, vinyl, and two-component epoxy and polyurethane coatings. Cures even at low temperatures (5 °C).Application: The substrate must be dry, clean, and prepared according to the relevant specification (e.g., ISO-Sa2½, SSPC P-16). Application can be done by airless or conventional spraying, brush, or roller. THINNER 91-92 is used for thinning.Technical DataSubstrates: Steel, galvanized steel, stainless steel, aluminumSurface preparation:Steel: Blasting according to ISO-Sa2½ (dry or wet), blast profile 30–75 µmGalvanized steel/stainless steel: Sweep blasting according to SSPC P-16Surfaces must be clean, dry, and free of contaminantsTopcoat: 2-component epoxy and polyurethane coatings (e.g., SIGMACOVER, SIGMADUR)Coverage: approx. 11.4 m²/l at 50 µm dry film thicknessThinner: THINNER 91-92 (Item No. 2590-101)Application method: Brush, roller, airless or conventional sprayingDrying times at 20 °C: Dust dry after 2 hrs, recoatable after 2 hrs, fully cured after 7 daysCertification: ACQPA 24142For more information, please refer to the technical data sheet under "Downloads".

Fast drying, one component and good rust protection zinc phosphate thick film multiprimer for steel above the waterline. Easy to apply, surface tolerant, dries quickly and has great anticorrosicve properties. Can be recoated with various one and two component products.Application: The substrate should be prepared in accordance with ISO-St2 (mechanical) or ISO-Sa2½ (blasted). Application is carried out using airless or air spray guns, brushes, or rollers. The recommended thinner is SIGMA THINNER 21-06. The minimum application temperature is 5°C. Ensure adequate ventilation during application and drying. Recoating is possible after just 4 hours at 20°C (with SIGMARINE 28, 48, or PPG VIKOTE 56). Intermediate sanding is not necessary.In accordance with the Chemicals Prohibition Ordinance, this product can only be shipped to resellers, professional users and public research and teaching institutes. Do you belong to this clientele? Then send us your inquiry here. We will be pleased to prepare a delivery offer for you. Private users can only be supplied in our store in Hamburg against proof of use.Technical DataSubstrate: SteelSurface preparation: Blast profile 40–70 µm, cleaned to ISO-Sa2½ or min. ISO-St2Topcoat: various products, e.g. SIGMARINE 48Coverage: approx. 7.3 m²/l at 75 µm dry film thicknessThinner: THINNER 21-06 (Art.No. 2580-100) Application method: Brush, roller, airless or conventional spray Drying times at 20 °C: Dust dry after 30 min; recoatable after 4 hrs Certification: Certified according to MEDFurther information on applying this product can be found in the technical data sheet under "Downloads".

EURO LOCK Zinc Dust Paint offers high-quality corrosion protection for all metals, with a zinc content of approx. 95 % in the dry film. Suitable for touching up galvanized anchors, anchor chains and for repairing welding and sheet metal work (electrically conductive during welding). Prevents rust and offers good protection against extreme weather conditions. Temperature resistant up to 500 °C. Suitable as a single coating or as a primer for further top coats on systems exposed to water and weathering.&nbsp