EPIFANES MULTIGUARD+ Black Paint

Extremely fast-drying, robust yacht enamel that dries only semi-gloss, resulting in a certain degree of slip resistance. Suitable for applications above the waterline, especially for heavily used areas such as walking decks and hatch coamings.The paint offers very good adhesion, is mechanically durable, and is suitable for areas subject to heavy use. By adding up to 25% EPIFANES Clear Varnish (Art.No. 2050-001), the gloss level can be increased; by adding EPIFANES Anti-Slip Additive (Art.No. 2059-002), the slip resistance of the paint on walking decks can be increased.Can be applied to wood, steel, and aluminum above the waterline, as well as for refurbishing already existing, intact paint systems.Application The surface must be clean, dry, dust- and grease-free. Before application on smooth surfaces, sanding is required. Application is done with brush, roller, or spray gun at temperatures between 5 °C and 25 °C and relative humidity below 85%. Between coats, intermediate sanding with P220–P280 is required. For steel and wood outdoors, a suitable EPIFANES primer such as MULTI MARINE PRIMER (Art.No. 2066-175) or WERDOL Primer (Art.No. 2052-175) is recommended.Technical DataApplication area: Semi-gloss enamel paint for decks, walking decks, and heavily used areasSurface: Steel, wood, concrete; primed, dry, sanded, cleanPrimer: Suitable EPIFANES primer depending on the surfaceCoverage: approx. 8–10 m²/l at 60 µm dry film thicknessThinner: EPIFANES PAINT THINNER (Art.No 2059-001) or 1-K SPRAY THINNER (Art.No 2059-110)Application method: Brush, roller, spray gun (professional users)Drying times (at 15°C): Dust dry: 2 hrs, re-coatable: 10 hrsFurther information on application can be found in the Technical Data Sheet under 'Downloads'.

EPIFANES BILGENFARBE is a one-component, air-drying protective coating based on oil-modified alkyd resins with a semi-gloss finish. It is intended for use in bilges, engine rooms and other areas where a hard and resistant coating is required. Suitable for applications on steel, GRP, wood and aluminum in conjunction with the appropriate primer system.Application: The substrate must be clean, grease-free, well sanded and dust-free. Apply with a brush, roller or sprayer at temperatures from 5 °C and a maximum relative humidity of 85 %. Stir well before use.Recommended wet film thickness: 70-80 µm (35-40 µm dry) or 100-200 µm (50-100 µm dry).Technical dataArea of application: Protective coating for bilges, engine rooms and other heavily used areasSubstrate: Steel, GRP, wood, aluminum

EPIFANES BLACK BOTTOM flexible bitumen-based protective coating for the area above and below the waterline.This modern version of the so-called black varnish adheres well to raw steel and wood surfaces as well as existing tar and bitumen layers and synthetic primers. It is easy to apply, offers high UV resistance, elasticity and protection against the changing influences of water and air.Note: It is recommended to apply the first layer with 15-25% with EPIFANES 1K-Spraythinner and use a stiff brush to work the paint onto the surface. For effective corrosion protection on new hulls, apply at least 250-300 μm to the raw substrate in the underwater area. Technical DataSubstrate: Steel, wood, existing tar coatings (repair/maintenance)Surface preparation:Clean, dry, degreased, well-sanded surface, free of rust, dust and adhesionDegrease with EPIFANES 1K Spray Thinner; rinse off water-soluble residues with fresh waterFollow-up coat: Overcoatable with EPIFANES Copper-Free AntifoulingCoverage: approx. 10 m²/l at 50 µm dry film thicknessThinner:Brush: EPIFANES Brush ThinnerSpray: EPIFANES Spray Thinner for 1C lacquers and primersAirless: EPIFANES D-100Application method: Brush, roller, conventional spray gun, airless sprayDrying times at 20 °C: Dust dry after 2 hrs, recoatable after 12 hrsFurther information on applying this product can be found in the technical data sheet under “Downloads”.

EPIFANES FLAT BLACK is a one-component, black matte finish based on urethane resin for interior and exterior areas. With a gloss rate of only 5–10%, it gives surfaces a modern, matte appearance. The product is resistant to alcohol and common household cleaners and has high scratch resistance.Application: The substrate must be clean, dry, grease-free, and sanded; application is done with a brush, roller, or spray gun. On GRP, steel, wood, or aluminum, a suitable primer such as EPIFANES MULTI MARINE PRIMER (Art.No. 2066-175) is recommended, depending on the material. Indoors, up to three coats are applied directly to the previously primed surface. Outdoors, a build-up with a high-gloss varnish such as EPIFANES MONO-URETHANE (Art.No. 2055-101) is recommended, followed by a final coating with 1–2 coats of EPIFANES FLAT BLACK.Technical DataApplication area: Matte finish for wood, steel, aluminum, GRP in interior and exterior areas above the waterlineSubstrate: Clean, dry, grease-free, sandedPrimer: Compatible with most EPIFANES paints and primersCoverage: approx. 15 m²/l at 35 µm dry film thicknessThinner: EPIFANES BRUSH THINNER FOR PAINTS & LACQUERS (Art.No. 2059-001); EPIFANES 1-C SPRAY THINNER (Art.No. 2059-110)Application method: Brush, roller, spray equipment (professional users)Drying times (at 15 °C): Dust dry: 3 hrs, sandable and re-coatable: 48 hrsFurther information on application can be found in the Technical Data Sheet under 'Downloads'.

“Pure Gold in a tin” - EPIFANES GOLD SPECIAL contains a very high proportion of metallic, pure gold dust pigments. This gold paint was developed on an acrylic copolymer basis for decorative stripes, ship names, and lettering on classic yachts, where traditionally gold leaf was laboriously applied. In contrast, EPIFANES GOLD SPECIAL is easier to apply than gold leaf and allows the included gold dust to shine in its typical gloss and color tone. Application: The surface must be dry, well degreased, and sanded. On GRP, steel, wood, and zinc, an adhesion-promoting primer with EPIFANES MULTI MARINE PRIMER (Art.No 2066-175) is recommended, which should be sanded with P180–P220 after drying. Stir well before use and stir occasionally during application to prevent the gold pigments from settling. Do not apply wet-on-wet and do not apply excessively thick wet coats. Preferably apply with a soft, long-bristled brush in a single, even stroke. For an even gold effect, apply at least two coats.Outdoors, to stabilize against UV rays, after complete curing (48 hrs) it can be overcoated with EPIFANES POLY-URETHANE CLEAR VARNISH (Art.No 2063-900) or EPIFANES CLEAR BOAT VARNISH (Art.No 2050-001); when using Clear Boat Varnish, the color tone appears slightly darker.Safety note: Contains solvents; wearing personal protective equipment (safety goggles, mask, gloves) is recommended.Technical DataArea of application: Gold paint for decorative coating of lettering, trim, ornamentsSurface: Dry, degreased, sanded; on GRP, steel, wood with primerPrimer: depending on surface, e.g., EPIFANES MULTI MARINE PRIMER, WASHPRIMER AQCoverage: approx. 2.0–2.5 m²/250 ml at approx. 45–55 µm dry film thicknessThinner: EPIFANES PAINT THINNER (Art.No. 2059-001)Application method: BrushDrying times (at 20 °C): Dust dry: 2 hrs, sandable: 24 hrs, recoat with itself: 9–12 hrs; recoat with clear varnish: approx. 48 hrs.

High-gloss, one-component urethane oil-based varnish with very good color fastness. EPIFANES MONO-URETHANE Yacht Varnish combines the ease of application of classic 1-component systems with the approximate hardness and weather resistance of a 2-component varnish. The product is suitable for new and renovation coatings on primed wood, steel, aluminum and GRP in interior and exterior areas above the waterline. Direct application without primer is possible on carefully degreased and sanded GRP.Application: For optimum adhesion, priming with EPIFANES MULTI MARINE PRIMER (Art. No. 2066-102) is required, for aluminum surfaces additionally with WASHPPRIMER AQ (Art. No. 2062-005). Apply with a brush, roller or sprayer at temperatures between 8 °C and 30 °C and relative humidity between 50 % and 85 %. Do not apply wet-on-wet. Intermediate sanding with P400 or Scotch-Brite is recommended between coats.Ordering the desired color: The EPIFANES MONO-URETHANE yacht varnish can be mixed in all RAL colors except metallics and luminous colors, and in all colors of the common maritime color manufacturers of EPIFANES. The varnish is also available in silk gloss. The delivery time is approx. 10 days. Please specify the exact color at the end of the order process under "Remarks".Technical dataArea of application: High-gloss paint for wood, steel, aluminum and GRP above the waterlineSurface: Clean, dry, grease-free, sandedPrimer: EPIFANES MULTI MARINE PRIMER, WASHPPRIMER AQ (aluminum)Coverage: approx. 14-15 m²/l at 40 µm dry film thicknessThinner: EPIFANES PINSELVERDÜNNER, 1-K SPRITZVERDÜNNUNG&nbsp

High-gloss, single-component varnish based on urethane oil with very good color stability. EPIFANES MONO-URETHANE Yacht Varnish combines the easy application of traditional 1-component systems with the approximate hardness and weather resistance of a 2-component varnish. The product is suitable for new and renovation coatings on primed wood, steel, aluminum, and fiberglass above the waterline for interior and exterior use. On carefully degreased and sanded fiberglass, direct application without primer is possible.Application: For optimal adhesion, appropriate priming with EPIFANES MULTI MARINE PRIMER (Art.No 2066-102) is required, and for aluminum surfaces additionally with WASHPPRIMER AQ (Art.No 2062-005). Application is done with brush, roller, or spray gun at temperatures between 8 °C and 30 °C and relative humidity between 50% and 85%. Do not apply wet-on-wet. An intermediate sanding with P400 or Scotch-Brite is recommended between coats.Note on the color chart: The colors shown correspond as closely as possible to the original colors, but deviations cannot be ruled out.Technical DataApplication area: High-gloss varnish for wood, steel, aluminum, and fiberglass above the waterlineSubstrate: Clean, dry, grease-free, sandedPrimer: EPIFANES MULTI MARINE PRIMER, WASHPPRIMER AQ (aluminum)Coverage: approx. 14–15 m²/l at 40 µm dry film thicknessThinner: EPIFANES BRUSH THINNER, 1-C SPRAY THINNER Application method: Brush, roller, or spray gun (professional users)Drying times (at 20 °C): Dust-dry: 1 hr, sandable: 24 hrs, recoatable: 24 hrsFurther information on application can be found in the technical datasheet under 'Downloads'.

EPIFANES MULTIGUARD+ is a tar-free, semi-gloss black marine paint suitable for bare steel surfaces as well as for the maintenance of existing tar and bitumen coatings. The coating has excellent adhesion to steel as well as to pretreated tar and bitumen layers. The paint is colorfast and resistant to alternating influences of water and air. Application is by brush, roller, or spray gun. Application: Stir well prior to application. Make sure to apply the product only in well ventilated areas. The temperature should be above 8°C while applying and during drying times. The first coat is applied to bare steel or to roughened or softened tar layers thinned with 20–25% EPIFANES 1K Spray Thinner (Art. No. 2059-110) or white spirit and applied with a stiff bristle brush. Subsequent coats are applied with a short-haired lambskin roller. The substrate must be clean, grease-free, and dust-free. Existing tar layers should be prepared by high-pressure cleaning, degreasing, and roughening with grit 60 or a suitable solvent.Technical DataApplication area: Above and below the waterline on steel and woodSubstrate: Bare steel, wood, existing tar/bitumen coatingsPrimer: Not required if surface preparation is adequateCoverage: Approx. 5 m²/l at 100 μm dry film thicknessThinning: EPIFANES Paint Thinner; EPIFANES 1K Spray Thinner; EPIFANES D-100Application method: Brush, roller, spray application (professional users)Drying times (at 20 °C): Dust dry after approx. 15 minutes, tack-free after approx. 45 minutes, recoatable after approx. 12 hoursFurther information on application can be found in the Technical Data Sheet under 'Downloads'.

EPIFANES MULTILUX is a high-gloss, non-yellowing 1-component white enamel based on siliconized alkyd resins. It is characterized by very good weather resistance, long-lasting gloss, fast drying, and good flow properties. Suitable as a topcoat for areas such as the bulwark or superstructures. Can be applied to gelcoat/GRP, steel, wood, and aluminum in interior and exterior areas above the waterline, as well as for repainting existing 1-C and 2-C coatings. On gelcoat, the paint can also be applied without primer if the surface is properly prepared.Application Apply with a long-haired, soft brush, roller, or spray gun at temperatures between 10 °C and 28 °C and relative humidity between 50 % and 75 %. Do not apply wet-on-wet, observe overcoating intervals. An intermediate sanding with P220 is recommended between coats. For long-term outdoor protection, at least 100–120 µm dry film thickness (approx. 3 brush coats or 4 roller coats) should be applied.Technical dataApplication area: Interior and exterior areas above the waterline Substrate: Intact, clean, degreased, and sanded 1-C or 2-C paints or primers; new gelcoat degreased and sandedPrimer: Common 1-C and 2-C primers such as EPIFANES MULTIMARINE PRIMER (Art.No. 2066-175)Coverage: approx. 13 m²/l at 40 µm dry film thicknessThinner: EPIFANES PAINT THINNER (Art.No. 2059-001), 1-C SPRAY THINNER (Art.No. 2059-110)Application method: Brush, roller, air spray (1.3–1.8 mm, 3 bar) or airless (0.013–0.015”, 140–160 bar)Drying times (at 20 °C): Dust dry: 1 h, sandable: 18 h, recoatable: 18 hFurther information on application can be found in the technical data sheet under 'Downloads'.

A high-gloss, single-component yacht paint based on a non-yellowing, siliconized alkyd resin. The binder ensures long-lasting gloss retention, minimal dirt adhesion, and high color stability. EPIFANES NAUTIFORTE Yacht Paint is easy to apply and offers high coverage due to high-quality pigments. Suitable for new coatings on wood, steel, and aluminum in combination with a suitable primer, as well as for GRP surfaces. Also suitable for maintaining existing, intact 1- and 2-component coatings above the waterline, regardless of the manufacturer.Application: The substrate must be clean, dry, free of grease, and sanded. Application is done with a roller, soft long-haired brush, or spray gun at temperatures from 8–30 °C and relative humidity between 50–85%. Do not apply wet-on-wet and avoid excessively thick wet coats to prevent runs and drying problems. Recommended primers for substrate preparation are EPIFANES MULTI MARINE PRIMER (Art.No. 2066-175), for new aluminum EPIFANES WASHPRIMER AQ (Art.No. 2062-005). For a new coating, three coats are recommended, each with intermediate sanding (P400 or sanding fleece) by hand. Note on the color chart: The colors shown correspond as closely as possible to the original colors, but deviations cannot be ruled out.Technical dataApplication area: High-gloss, non-yellowing yacht varnish for wood, steel, aluminum, GRP above the waterlineSubstrate: Clean, dry, grease-free, sanded; in combination with suitable primerPrimer: EPIFANES MULTI MARINE PRIMER, EPIFANES WASHPRIMER AQ Coverage: approx. 14 m²/l at 40 µm dry film thicknessThinner: EPIFANES Paint Thinner (Art.No 2059-001), EPIFANES 1-K Spray Thinner (Art.No 2059-110) Application method: Brush, roller, spray gun (professional users)Drying times (at 20 °C): Dust dry: 1 hr, sandable and recoatable: 18 hrsFurther information on application can be found in the Technical Data Sheet under 'Downloads'.

A high-gloss, extremely hard 2-component finish coat based on saturated polyester resins and isocyanate with integrated UV filter. EPIFANES POLY-URETHANE YACHT COATING is particularly scratch-, impact-, and abrasion-resistant and offers very good weather and water resistance even in tropical climates. Suitable for wood, steel, aluminum, and GRP in interior and exterior areas above the waterline. Can be applied directly to thoroughly degreased and sanded polyester surfaces and is compatible with common epoxy and polyurethane primers.Application: The two components are mixed in a ratio of 2:1 (base:hardener, by weight) and ideally left to stand for 30 minutes (induction time). Application is done with brush, roller, or spray gun at temperatures from 10–30 °C and relative humidity between 50% and 75%. Do not apply wet-on-wet. Between coats, an intermediate sanding with P360–P400 is required if the next coat is not applied within 24 hours. Thinning is possible with EPIFANES PU BRUSH THINNER (Art.No. 2059-301) or PU SPRAY THINNER (Art.No. 2059-310).Custom color order: POLY-URETHANE YACHT COATING can be mixed in all RAL colors except metallics and fluorescent colors, and in all colors of the common maritime paint manufacturers from EPIFANES. The varnish is also available in satin gloss. Delivery time is approx. 10 days. Please specify the exact color shade at the very end of the ordering process under "Remarks".Technical dataApplication area: Non-working solid wood, plywood, steel, aluminum, and GRP above the waterlineSubstrate: Clean, dry, grease-free, sanded; GRP at least 14 days oldPrimer: EPIFANES EPOXY PRIMER or EPOXY HB COAT depending on materialCoverage: approx. 12–14 m²/l at 35–40 µm dry film thicknessThinner: EPIFANES PU BRUSH THINNER, PU SPRAY THINNER Application method: Brush, roller, or spray gun (professional users)Drying times (at 20 °C): Dust dry: 2 hrs, tack-free: 4 hrs, sandable and re-coatable: 24 hrsFurther information on application can be found in the technical data sheet under 'Downloads'.Safety note: Contains isocyanates. May cause allergic reactions. 

EPIFANES POLY-URETHANE DD-YACHT VARNISH COLORED is a high-gloss, extremely hard 2-component colored varnish based on saturated polyester resins and isocyanate with integrated UV filter. The product is particularly scratch-, impact-, and abrasion-resistant and offers very good weather and water resistance even in tropical climates. Suitable for wood, steel, aluminum, and GRP in interior and exterior areas above the waterline. Can be applied directly to thoroughly degreased and sanded polyester surfaces and is compatible with common epoxy and polyurethane primers.Application: The two components are mixed in a ratio of 2:1 (base:hardener, by weight) and ideally left to stand for 30 minutes (induction time). Application is carried out with a brush, roller, or spray gun at temperatures of 10–30 °C and relative humidity between 50% and 75%. Do not apply wet-on-wet. Between coats, intermediate sanding with P360–P400 is required unless the next coat is applied within 24 hrs. Dilution possible with EPIFANES PU BRUSH THINNER (Art. No. 2059-301) or PU SPRAY THINNER (Art. No. 2059-310).Note on the color chart: The colors shown correspond as closely as possible to the original colors, but deviations cannot be ruled out.Technical DataApplication area: Wood, steel, aluminum, and GRP above the waterlineSubstrate: Clean, dry, grease-free, sanded; GRP at least 14 days oldPrimer: EPIFANES EPOXY PRIMER or EPOXY HB COAT depending on materialCoverage: approx. 12–14 m²/l at 35–40 µm dry film thicknessThinning: EPIFANES PU BRUSH THINNER, PU SPRAY THINNER Application method: Brush, roller, or spray gun (professional users)Drying times (at 20 °C): Dust dry: 2 hrs, tack-free: 4 hrs, sandable and recoatable: 24 hrsFurther information on application can be found in the Technical Data Sheet under 'Downloads'.Safety Note: Contains isocyanates. may cause allergic reactions. 

EPIFANES SATIN FINISH WHITE is a single-component satin gloss varnish based on urethane/alkyd resin for interior and exterior areas above the waterline. It is characterized by optimal flow, high coverage, and resistance to weathering as well as common household cleaning agents. The product is suitable for use on wood, steel, GRP, and aluminum in combination with the appropriate primer system. Suitable as a satin-matt finish over a high-gloss paint system.Application Application is carried out with a brush, roller, or spray gun at temperatures of 8–30 °C and relative humidity between 50% and 85%. In interior areas, 2–3 coats are applied to the previously primed surface. Intermediate sanding with P320–P400 is required between coats. Thinning with EPIFANES PAINT THINNER (Art.No. 2059-001) or 1-C SPRAY THINNER (Art.No. 2059-110) is possible.Technical dataApplication area: Satin-matt varnish for wood, steel, GRP, and aluminum above the waterlineSubstrate: Clean, dry, grease-free, sandedPrimer: EPIFANES MULTI MARINE PRIMER, MONO-URETHANE or WASHPRIMER AQ depending on substrateCoverage: approx. 13–15 m²/l at 40 µm dry film thicknessThinner: EPIFANES BRUSH THINNER, 1-C SPRAY THINNERApplication method: Brush, roller, spray gun (professional users)Drying times (at 20 °C): Dust dry: 2 hrs, sandable: 24 hrs, recoatable: 24 hrsFurther information on application can be found in the Technical Data Sheet under 'Downloads'.

EPIFANES WATERLINE PAINT is a high-gloss, 1-component enamel based on urethane/alkyd resin, specially formulated for the waterline area. It is suitable for fresh and saltwater areas and offers increased protection against weathering to maintain gloss and color stability in the transition area between water and air. Applicable to GRP/gelcoat, steel, wood, and aluminum above the waterline. Application It is recommended to apply with a long-haired, soft brush, a mohair roller, or spray gun at temperatures between 10 °C and 28 °C and relative humidity between 50% and 75%. Before application, stir the can well. Do not work wet-on-wet. For a new build, at least two coats of EPIFANES WATERLINE PAINT are recommended. Between coats, sand lightly with P400. Thinning with EPIFANES PAINT THINNER (Art.No 2059-001) or 1-C SPRAY THINNER (Art.No 2059-110) is possible.TIP: It is recommended to paint the waterline 5–10 cm above the water (at full load) so that the paint does not have constant water exposure later.  Note on the color chart: The colors shown correspond as closely as possible to the original colors, but deviations cannot be ruled out.Technical DataApplication area: Waterline, on already coated surfacesSubstrate: Intact, clean, degreased, and sandedPrimer: EPIFANES MULTI MARINE PRIMER (Art.No 2055-301)Coverage: approx. 3–4 m²/250 ml at 40 µm dry film thicknessThinning: EPIFANES PAINT THINNER, 1-C SPRAY THINNER Application method: Brush, roller, spray (professional users)Drying times (at 20 °C): Dust-dry: 3 hrs, sandable: 24 hrs, overcoatable: 24 hrsFurther processing information can be found in the Technical Data Sheet under 'Downloads'.

A high-gloss single-component marine varnish based on linseed oil/alkyd resin with very good coverage and flow properties. EPIFANES WERDOL COASTERLACK offers long-lasting gloss, high weather resistance, and is suitable for interior and exterior use above the waterline. It can be used on steel, wood, aluminum, or gelcoat in combination with a suitable primer and is also suitable for reworking existing, intact 1- or 2-component coatings.Application: The surface must be clean, dry, grease-free, and sanded. Suitable primers are EPIFANES MULTI MARINE PRIMER or WERDOL PRIMER PAINT. On new aluminum, EPIFANES WASHPRIMER AQ must be applied beforehand. An intermediate sanding with P400 (by hand) is recommended between coats. Application is by brush, roller, or spray gun at 10–28 °C and 50–75 % relative humidity. Do not apply coats wet-on-wet. For increased UV protection, a dry film thickness of at least 100–120 µm in 3–4 coats should be achieved.Technical DataApplication area: High-gloss 1-C marine varnish for gelcoat, wood, steel, and aluminum above the waterlineSurface: Intact, clean, degreased, and sanded 1- or 2-C paints or primersPrimer: EPIFANES MULTI MARINE PRIMER (Art.No. 2066-175), WERDOL PRIMER PAINT (Art.No. 2052-175), WASHPRIMER AQ (Art.No. 2062-005)Coverage: approx. 15 m²/l at 40 µm dry film thicknessThinner: EPIFANES PAINT THINNER (Art.No. 2059-001), EPIFANES 1-C SPRAY THINNER (Art.No. 2059-110)Application method: Brush, roller, spray gun (professional users)Drying times (at 20 °C): Dust-dry: 3 hrs, recoat: 24 hrsFor more information on application, please refer to the Technical Data Sheet under 'Downloads'.

Classic, high-gloss yacht varnish based on alkyd resin for applications above the waterline. EPIFANES YACHT ENAMEL is suitable for primed surfaces made of wood, steel, aluminum, and fiberglass for interior and exterior use and is resistant to salt and fresh water. It is known for its optimal flow properties, long-lasting gloss, and good weather resistance. Compatible with many existing 1-component and 2-component systems and can also be overcoated with EPIFANES MONO-URETHANE (Art.No. 2055-101) or EPIFANES NAUTIFORTE (Art.No. 2054-102).Application The surface must be clean, dry, dust- and grease-free. Sand old coatings, remove loose or non-adhering layers. Application is done with brush, roller, or spray gun at temperatures above 8 °C and relative humidity below 85%. Do not apply wet-on-wet. For even gloss, intermediate sanding is required. The recommended wet film thickness is 70–80 µm, corresponding to 35–40 µm dry. As a primer, use EPIFANES MULTI MARINE PRIMER (Art.No 2062-102), additionally WASHPRIMER AQ (Art.No 2062-005) for aluminum surfaces.Note on the color chart: The colors shown correspond as closely as possible to the original colors, but deviations cannot be ruled out.Technical DataApplication area: High-gloss varnish for wood, steel, aluminum, and fiberglass above the waterlineSubstrate: Clean, dry, grease-free, sanded; fiberglass at least 14 days oldPrimer: EPIFANES MULTI MARINE PRIMER, WASHPRIMER AQ Coverage: approx. 14 m²/l at 40 µm dry film thicknessThinner: EPIFANES COLOR THINNER, 1-C SPRAY THINNERApplication method: Brush, roller, spray gun (professional application)Drying times (at 20 °C): Dust-dry: 2 hrs, sandable: 24 hrs, recoatable: 24 hrsFurther information on application can be found in the technical datasheet under 'Downloads'.

Classic, high-gloss yacht enamel based on alkyd resin for applications above the waterline. EPIFANES YACHT ENAMEL Black is suitable for primed surfaces made of wood, steel, aluminum, and GRP for both interior and exterior use, and is resistant to salt and fresh water. It is characterized by optimal flow properties, long-lasting gloss, and good weather resistance. Compatible with many existing 1-component and 2-component systems.Application The substrate must be clean, dry, free of dust and grease. Sand old coatings, remove loose or non-adherent layers. Application is done with a brush, roller, or spray gun at temperatures above 8 °C and relative humidity below 85 %. Do not apply wet-on-wet. For uniform gloss, intermediate sanding is required. The recommended wet film thickness is 70–80 µm, corresponding to 35–40 µm dry. As a primer, use EPIFANES MULTI MARINE PRIMER (Art.No. 2062-102), for aluminum surfaces additionally use WASHPRIMER AQ (Art.No. 2062-005).Technical dataApplication area: High-gloss varnish for wood, steel, aluminum, and GRP above the waterlineSubstrate: Clean, dry, grease-free, sanded; GRP at least 14 days oldPrimer: EPIFANES MULTI MARINE PRIMER, WASHPRIMER AQCoverage: approx. 14 m²/l at 40 µm dry film thicknessThinner: EPIFANES PAINT THINNER, 1-C SPRAY THINNERApplication method: Brush, roller, spray gun (professional use)Drying times (at 20 °C): Dust dry: 2 hrs, sandable: 24 hrs, recoatable: 24 hrsFurther information on application can be found in the technical data sheet under 'Downloads'.

Classic, high-gloss yacht varnish based on alkyd resin for applications above the waterline. EPIFANES BOOTSLACK colored is suitable for primed surfaces made of wood, steel, aluminium and GRP indoors and outdoors and is resistant to salt and fresh water. It is characterized by optimum flow properties, long-lasting gloss and good weather resistance. Compatible with many existing 1-component and 2-component systems and can also be recoated with EPIFANES MONO-URETHANE (Art. No. 2055-101) or EPIFANES NAUTIFORTE (Art. No. 2054-102).Application The substrate must be clean, dry and free of dust and grease. Sand old coats, remove loose or non-adherent layers. Apply with a brush, roller or sprayer at temperatures above 8 °C and relative humidity below 85 %. Do not apply wet-on-wet. Intermediate sanding is required for a uniform gloss. The recommended wet film thickness is 70-80 µm, corresponding to 35-40 µm dry. Use EPIFANES MULTI MARINE PRIMER (Art. No. 2062-102) as a primer, for aluminum surfaces additionally&nbsp

Classic, high-gloss yacht varnish based on alkyd resin for applications above the waterline. EPIFANES BOAT VARNISH pure white is suitable for primed surfaces made of wood, steel, aluminum, and GRP for interior and exterior use and is resistant to salt and fresh water. It is characterized by optimal flow properties, long-lasting gloss, and good weather resistance. Compatible with many existing 1-component and 2-component systems and can also be overcoated with EPIFANES MONO-URETHANE (Art.No. 2055-101) or EPIFANES NAUTIFORTE (Art.No. 2054-102).Application: The surface must be clean, dry, dust- and grease-free. Sand old coatings, remove loose or non-adhering layers. Application is carried out with brush, roller, or spray gun at temperatures above 8 °C and relative humidity below 85 %. Do not apply wet-on-wet. For an even gloss, intermediate sanding is required. The recommended wet film thickness is 70–80 µm, corresponding to 35–40 µm dry. As a primer, use EPIFANES MULTI MARINE PRIMER (Art.No. 2062-102); for aluminum surfaces additionally use WASHPRIMER AQ (Art.No. 2062-005).Technical dataApplication area: High-gloss varnish for wood, steel, aluminum, and GRP above the waterlineSubstrate: Clean, dry, grease-free, sanded; GRP at least 14 days oldPrimer: EPIFANES MULTI MARINE PRIMER, WASHPRIMER AQCoverage: approx. 14 m²/l at 40 µm dry film thicknessThinner: EPIFANES PAINT THINNER, 1-C SPRAY THINNERApplication method: Brush, roller, spray gun (professional use)Drying times (at 20 °C): Dust dry: 2 hrs, sandable: 24 hrs, re-coatable: 24 hrsFor further information on application, please refer to the Technical Data Sheet under 'Downloads'.

HEMPEL MULTICOAT is a one-component, alkyd-based paint with good resistance to water and oil.The paint is characterized by its durability, UV resistance good application properties.Suitable for all boatbuilding substrates inside and outside above the waterline where a semi-gloss finish is desired.Most common applications: Bilge, storage areas or deck surfaces. Can be used as a complete coating system.Suitable thinner: HEMPEL 811Yield approx. 11 m²/l (40 µm).Note: Please observe the application instructions in the technical data sheet before and during application.

High-quality alkyd resin-based paint that adheres to almost all substrates even without a primer.OWATROL DECO can even be applied directly to hand-rusted metal surfaces, weathered substrates or substrates with stubborn old coats. Does not adhere to substrates treated with wax, silicone, fluoropolymers or other release coatings. Temperature resistant up to 175 °C.Technical dataArea of application: Metal, wood, old coatings - interior and exteriorSubstrate: clean, dry, sound, free from wax, silicone, fluoropolymersApplication: Brush, roller, brush pad, spray gun (airless max. 10 % synthetic resin thinner)Coverage: approx. 15 m²/lDilution: none (spray application with max. 10 % thinner)Application temperature: 5 °C to 35 °CDrying (20 °C): dust-dry after 6 hours, recoatable after 24 hours.Further information on processing can be found in the technical data sheet under "Downloads".

Fast-drying, glossy single-component alkyd paint. SIGMARINE 48 is particularly suitable as a topcoat on decks, e.g., outer hull or superstructures. The paint is water- and weather-resistant, durable and can be applied over most intact alkyd coatings. Also suitable for areas exposed to changing atmospheric and immersion conditions (e.g., bilges). By adding SIGMA Antislip Powder (Item No. 2586-100), the paint can additionally be made non-slip for deck coatings.Application: The substrate must be clean, dry, and free of contaminants. Existing coatings should be roughened if necessary. Stir well before use. Ideally apply the product at temperatures above 15 °C using a brush, roller, air or airless spray equipment. The recommended thinner is SIGMA THINNER 20-05. Due to solvent evaporation, adequate ventilation must be ensured during application and drying.This product may only be shipped to resellers, professional users, and public research and educational institutions in accordance with the EU Chemicals Prohibition Ordinance (REACH). Are you part of this customer group? Then send us your inquiry here along with appropriate user verification. We will gladly provide you with a delivery offer. Note on color chart: Due to monitor or printer settings, the color tones shown here may differ from the original shades and serve only as a reference. Upon request, we will gladly send you the color chart.Technical DataApplication area: Topcoat for outdoor areas with alternating water and air exposureSubstrate: Intact alkyd coatings, dry and clean, sandedPrimer: none, steel with suitable primerCoverage: approx. 12.6 m²/l at 35 µm dry film thicknessThinner: THINNER 20-05 (Item No. 2589-101)Application method: Brush, roller, air or airless sprayingDrying times (at 20 °C): Dust dry: 3 hrs, recoatable: from 24 hrsCertification: MEDFor more information on application, please refer to the technical data sheet under 'Downloads'.

SIGMARINE 49 is a high-gloss alkyd topcoat for interior and exterior areas above the waterline. It is easy to apply with a brush and shows very good flow, high weather resistance, opacity and color stability. The paint is also resistant to sulphur dioxide (occurs in areas with high levels of air pollution). Not suitable for permanent exposure to water or continuous exposure to spray water.

Classic, high-gloss graphite paint based on alkyd and urethane resins, e.g. for the hatch coaming and numerous other applications for interior and exterior use above the waterline. The coating is suitable for steel surfaces above the waterline and creates a smooth, dark metallic glossy surface. Due to the smooth and non-porous surface, dirt does not stick to it and the paint is easy to clean.Application: The surface must be clean, dry, grease-free, and sanded. For steel, a primer with a suitable primer such as EPIFANES MULTI MARINE PRIMER is recommended. Stir well before use. Apply with brush, roller, or spray gun at temperatures from 10 °C. Thinning is possible with EPIFANES PAINT THINNER or white spirit. Intermediate sanding between coats is recommended. Recoatable after approx. 18 hours at 18 °C.Technical DataArea of application: Glossy graphite paint for applications on steel surfaces above the waterlineSurface: Steel, clean, dry, grease-free, and sandedPrimer: EPIFANES MULTI MARINE PRIMER (Art.No. 2066-175) Coverage: approx. 12 m²/lThinner: EPIFANES PAINT THINNER (Art.No. 2059-001) or white spiritApplication method: Brush, roller, or spray gunDrying times (at 18 °C): Recoatable after approx. 18 hrsFurther information on application can be found on the product packaging.