- Rigg & sail
- Rope & cordage
- Anchoring & mooring
- Hull & deck
- Cabin & comfort
- Paint & boatbuilding
- Electrics & engine
- Pumps & sanitation
- Safety & VHF radio
- Navigation & books
- Commercial shipping
Thinner & additives
The EPIFANES Hardener is suitable for accelerating the drying time of all semi-synthetic one-component varnishes and paints from EPIFANES. Suitable for use on surfaces where the varnish needs to dry faster due to temperature or time constraints, or indoors (e.g. on furniture, work surfaces), where an abrasion-resistant, less flexible varnish surface is desired.Application: Mix 5 - 7 % of the hardener into the desired varnish color. Adding this amount significantly reduces the drying time of the varnish without substantially affecting its technical properties. Adding a higher amount of hardener (max. 50%) makes the varnish harder and more abrasion-resistant, but may result in a loss of gloss, UV stability, elasticity and brushability.Important: Not suitable for use with the EPIFANES varnishes MONO-URETHANE or NAUTIFORTE.
Special thinner for spraying PU-SPEEDCOAT from EPIFANES. Attention: This product is no longer manufactured, the stock is remaining stock.
OWATROL MARINE STRIP (also sold under the name DILUNETT) is a highly effective, water-based paint and antifouling remover for outdoor use on boats and yachts. It removes up to eight coats of paint in a single operation - completely without solvents and without aggressive vapors. Thanks to its gel-like consistency, it also adheres to vertical surfaces such as hulls or mirrors, making it ideal for use on decks, hulls or superstructures.Enables the efficient removal of varnishes, oil-based paints, stains and antifoulings with little effort. MARINE STRIP is simply applied in a thick layer, works for several hours and can then be removed with water and a brush with synthetic bristles or a high-pressure cleaner. For the after-treatment of wooden surfaces, the combination with OWATROL DECK CLEANER is recommended to neutralize the wood and restore the natural color.Technical DataApplication area: Removal of one-component coatings, antifoulings, wood oils, stains, grey weatheringSubstrate: wood, GRP, gelcoat, metal, plastic – not suitable for aluminiumApplication: brush, spatulaCoverage: approx. 4 m²/lThinner: noneApplication temperature: +5 °C to +35 °C (avoid direct sunlight)Drying (20 °C): exposure time 5–60 min, rinse thoroughly, allow surface to dry at least 48 hrsFurther information on application can be found in the Technical Data Sheet under "Downloads".
Special thinner for YACHTCARE epoxy resin systems. It is used to adjust the processing viscosity in epoxy coatings and is also suitable for cleaning tools after application.Application: Use only in combination with YACHTCARE epoxy resin products. Add in small amounts until the desired viscosity is achieved. Do not overdose, as this may impair curing and layer formation. Also suitable for cleaning brushes, rollers, and spray equipment. Observe safety and application instructions on the container and safety data sheet.Technical DataApplication area: Thinning and cleaning in connection with YACHTCARE epoxy resin productsCompatible products: YACHTCARE EPOXY PRIMER (Art.No. 2520-014)Application method: Add to the epoxy resin system according to manufacturer specifications; clean tools by rinsing with thinner
This thinner is suitable for adjusting the YACHTCARE antifouling primer and for cleaning the tools.It should only be added to the antifouling primer if the primer is too viscous (e.g. at low temperatures).Also suitable for YACHTCARE 1-component coatings such as varnishes, primers and paints. It is used to adjust the processing viscosity and is also suitable for cleaning tools after use.Application: Only use with the YACHTCARE 1-component products intended for this purpose. Add in small quantities until the recommended viscosity is reached. Do not overdose in order not to impair drying and layer build-up. Also suitable for cleaning brushes, rollers and spraying equipment. Observe the safety and processing instructions on the container and safety data sheet.Technical dataArea of application: Dilution and cleaning of YACHTCARE 1-component coatingsCompatible products: YACHTCARE ANTIFOULING PRIMER (Art. 2520-012)
Xylene-based thinner for use with epoxy paints. Recommended for SEAJET 017, SEAJET 117 and SEAJET 118. Can also be used for cleaning tools.Application: Add in small amounts to the coating, usually not more than 5 %. Ensure good ventilation, avoid skin contact and inhalation of spray mist. Safety precautions must be observed: product is flammable, keep away from sparks, open flames and heat sources.Technical DataApplication area: Thinner for SEAJET epoxy products 017, 117, 118Application method: Add to coating as specified by manufacturer; also for cleaning of toolsPack sizes: 1 L, 5 LShelf life: Minimum 3 years at 20 °CFurther information on application can be found in the Technical Data Sheet under 'Downloads'.
>According to german legislation this product may only be sent to resellers, professional users and public research institutes.If this applies to you, please request a quotation here.You may also buy this product personally in our showroom in Hamburg.Thinner 20-05 for SIGMARINE single component varnish and primers No. 24, 40, 42, 48, 49.
HANSASOL EP THINNER is a solvent-based thinner for 2-component coatings based on epoxy resin like HANSAZINC. The mixture of aromatics and alcohols is specially matched to epoxy resin coating materials and can also be used for cleaning suitable work equipment. Processing instructions: Add the thinner only after mixing the base and hardener. Not suitable for 2-component coating materials based on polyurethane (PU, PUR, DD) as well as paints based on certain polymers such as PVC or acrylate. Not suitable for degreasing surfaces. Ensure good ventilation during processing, keep ignition sources away and wear suitable personal protective equipment.Technical dataApplication area: Thinning of 2K EP coatings, e.g. HANSAZINC (Item no. 2670-102)Storage stability: in unopened original containers at 15–25 °C for at least 12 months.Further information on application can be found in the Technical Data Sheet under 'Downloads'.
