Aromatic-free brush thinner with high dilution power for most single-component primers, paints, and varnishes; very pure due to double distillation.Application: only stir the paint thinner into the varnish or paint in small amounts if necessary and mix thoroughly. Do not dilute more than necessary; excessive addition can cause runs and reduce the dry film thickness. Use only the thinners recommended by the manufacturer. Read the label/product information or safety data sheet before use.Technical DataApplication area: Dilution of 1K primers, paints, and varnishes; designed for brush/roller applicationApplication method: Add to the respective 1K coating, designed for brush/roller processing

Solvent-based cleaner for cleaning tools and equipment after using Epifanes 1-component varnishes, primers, and paints. Reliably removes fresh varnish and paint residues.Application: Rinse brushes, rollers, or spray equipment with Epifanes cleaning thinner immediately after use. Use only outdoors or in well-ventilated areas. Do not use for thinning varnishes. Observe safety instructions on the container and in the safety data sheet.Important: Not suitable for GRP surfaces; for this purpose, EPIFANES Polyester Degreaser (Art.No. 2059-401) is recommended.Technical DataArea of application: Cleaning of work equipment after processing Epifanes 1-C productsApplication method: Dip or rinse tools in thinner

Penetrating oil based on natural oils, which is used as an additive to improve the flow properties of conventional and semi-synthetic paints. It reduces visible brush strokes, impregnates wood and has a rust-inhibiting effect on steel by penetrating deep into the substrate. This means that a favorable result can be achieved even under difficult conditions.

Epifanes Polyester Degreaser for cleaning all plastic surfaces. Removes wax and oily components on polyester and is therefore recommended for cleaning before the application of paint systems. During application, make sure that the cloth is always clean and, if necessary, turn or change it more often so that the dirt is really removed from the surface.

The EPIFANES hardener is suitable for all semi-synthetic single-component varnishes and paints from EPIFANES. Especially in interior areas (e.g. on furniture, work surfaces), where an abrasion-resistant coating system is desired, the hardener can be mixed into the varnish.By adding a maximum of 5 - 7%, the curing time of the varnishes is already significantly reduced without the varnishes losing their essential qualities. By adding up to 50% of the hardener, the varnishes become significantly harder and more abrasion-resistant, but also lose their elasticity.

Special thinner for Epifanes 2-component polyurethane paints. Developed for use at higher ambient temperatures to delay drying speed and ensure even flow of the coating.Application: Use only for Epifanes 2-C-PU products. Add to the paint in small amounts to achieve the desired viscosity. Especially suitable for high temperatures or large-area coatings. Observe safety and handling instructions on the container and safety data sheet.Technical DataApplication area: Thinning Epifanes 2-C polyurethane paints at high temperaturesApplication method: Add to the paint mixture in the dosage recommended by the manufacturer

A fast evaporating thinner for spray applications of EPIFANES POLY-URETHANE Yacht paints and varnishes.

Special thinner for spraying PU-SPEEDCOAT from EPIFANES. Attention: This product is no longer manufactured, the stock is remaining stock.

Colorless, aromatic-free special thinner for spray application of Epifanes 1-component varnishes, primers, and paints. Developed to achieve the correct spray viscosity.Application: Use only for spray application of Epifanes 1-C products. Add thinner in small amounts until the recommended spray viscosity is achieved. Do not overdose, as this can negatively affect drying and film thickness. Observe the safety and processing instructions on the product packaging.Technical DataApplication area: Thinner for spray application of Epifanes 1-C varnishes, primers, and paintsApplication method: Add to Epifanes 1-C products to adjust spray viscosity

Pure stand oil. When adding 2 % maximum it can prolong the initial drying period and the process time of all half syntectic single component boat varnishes and coloured lacquer.

Universal special thinner for various Epifanes products such as EPIFANES CR Antifouling Primer or antifoulings such as EPIFANES FOUL-AWAY. It is used to adjust the application viscosity and is also suitable for cleaning tools after application.Application: Add to the respective Epifanes product in small quantities until the desired viscosity is achieved. Do not dilute more than necessary to avoid impairing drying and layer build-up. Also suitable for cleaning brushes, rollers and spraying equipment after use. Observe the safety instructions on the container and safety data sheet.

Thinner for all Epifanes epoxybased products, like EPIFANES EPOXY PRIMER or EPIFANES INTERIMCOAT. Also suited for soften existing epoxy to allow better bonding for fresh layers.

Special thinner for Epifanes Poly-Propoxides (PP) 2-component products. Developed to adjust processing viscosity and to clean the tools used after working with these systems.Application: Use only for thinning Epifanes PP-2C products in the quantities specified by the manufacturer. Do not overdose, as this may negatively affect drying and layer formation. Also suitable for cleaning brushes, rollers, and spray equipment after processing PP systems. Observe safety and handling instructions on the container and safety data sheet.Technical DataApplication area: Thinning and cleaning with Epifanes Poly-Propoxides (PP) 2-component productsApplication method: Add to paint or primer mixture according to manufacturer's instructions; clean tools by rinsing

HEMPEL Thinner No. 808 is suitable for thinning single-component HEMPEL antifoulings and for cleaning tools such as brushes or rollers.

HEMPEL'S Thinner No. 811 is suitable for thinning and cleaning tools for one-component primers, top coats and lacquers from HEMPEL.

The thinner HEMPEL Thinner No. 845 is suitable for thinning and cleaning the HEMPEL Light Primer (Art. No. 2577-055).

International Thinner No.9.For two-component clear coats. 1 l container.

INTERNATIONAL THINNER No.1. is a universal thinner for one-component products (except Primocon and antifoulings) and for varnishes.Technical dataArea of application: Thinning of INTERNATIONAL 1K productsCompatible with: INTERNATIONAL ORIGINAL Art.No. 2550-001), COMPASS (Art.No. 2550-076), SCHOONER (Art.No. 2550-073)

LE TONKINOIS GELOMAT is a matting agent for combination with all LE TONKINOIS lacquers. It is added to the last coat of lacquer to achieve a satin to matt surface. Depending on the mixing ratio, different gloss levels such as matt, silk matt or silk gloss can be achieved.Application For a matt surface, mix LE TONKINOIS GELOMAT and lacquer in a ratio of 1:1. For silk matt results, use a ratio of 1:2, for silk glossy surfaces, use a ratio of 1:3. Ensure good ventilation during application. The drying time corresponds to that of the paint product used.Further information can be found in the technical data sheet under 'Downloads'.

LE TONKINOIS Thinner is a universally applicable thinner for all solvent-based LE TONKINOIS products, linseed oil varnish (Art.No. 2691-001), as well as for cleaning brushes and tools, degreasing surfaces, and removing resin or wax contaminants. Application: Always ensure good ventilation during use. LE TONKINOIS Thinner can be used both for targeted thinning during application and for cleaning purposes. Ingredients: IsoaliphaticsFurther information on application can be found in the technical data sheet under 'Downloads'.

Color additive for the underwater coating LeFANT T-COAT. Mix the color additive with the primer, then add the hardener and stir thoroughly. One paint pot is sufficient for a 750 ml can.

LeFant Multi-Thinner is recommended as a thinner for LeFant Epoxy Primer and as a tool and surface cleaner.

OWATROL MARINE STRIP (also sold under the name DILUNETT) is a highly effective, water-based paint and antifouling remover for outdoor use on boats and yachts. It removes up to eight coats of paint in a single operation - completely without solvents and without aggressive vapors. Thanks to its gel-like consistency, it also adheres to vertical surfaces such as hulls or mirrors, making it ideal for use on decks, hulls or superstructures.Enables the efficient removal of varnishes, oil-based paints, stains and antifoulings with little effort. MARINE STRIP is simply applied in a thick layer, works for several hours and can then be removed with water and a brush with synthetic bristles or a high-pressure cleaner. For the after-treatment of wooden surfaces, the combination with OWATROL DECK CLEANER is recommended to neutralize the wood and restore the natural color.Technical DataApplication area: Removal of one-component coatings, antifoulings, wood oils, stains, grey weatheringSubstrate: wood, GRP, gelcoat, metal, plastic – not suitable for aluminiumApplication: brush, spatulaCoverage: approx. 4 m²/lThinner: noneApplication temperature: +5 °C to +35 °C (avoid direct sunlight)Drying (20 °C): exposure time 5–60 min, rinse thoroughly, allow surface to dry at least 48 hrsFurther information on application can be found in the Technical Data Sheet under "Downloads".

Type A thinner can be used for many SEAJET products, such as antifoulings and the primer SEAJET Type 015. 5% thinner is usually sufficient as an additive for paint. Can also be used for cleaning painting tools.&nbsp

Xylene-based thinner for use with epoxy paints. Recommended for SEAJET 017, SEAJET 117 and SEAJET 118. Can also be used for cleaning tools.Application: Add in small amounts to the coating, usually not more than 5 %. Ensure good ventilation, avoid skin contact and inhalation of spray mist. Safety precautions must be observed: product is flammable, keep away from sparks, open flames and heat sources.Technical DataApplication area: Thinner for SEAJET epoxy products 017, 117, 118Application method: Add to coating as specified by manufacturer; also for cleaning of toolsPack sizes: 1 L, 5 LShelf life: Minimum 3 years at 20 °CFurther information on application can be found in the Technical Data Sheet under 'Downloads'.

Special thinner based on aromatic hydrocarbons for the application of polyurethane coatings, single-component paints, and epoxy resin systems. THINNER 21-06 is also suitable for cleaning tools and equipment before and after application.Application: Use only in conjunction with the designated PPG coatings. Add thinner according to manufacturer instructions to achieve the desired viscosity. Observe safety and application instructions on the container and safety data sheet, and wear personal protective equipment.Technical DataApplication area: Thinning of PPG polyurethane, epoxy, and 1-component coatings; cleaning of toolsCompatible products: SIGMA VIKOTE 18 (Art. 2580-125), SIGMA ECOFLEET 290S (Art. No. 2584-003)Shelf life: At least 60 months when stored in a cool, dry placeFor more information on application, refer to the technical data sheet under 'Downloads'.

>According to german legislation this product may only be sent to resellers, professional users and public research institutes.If this applies to you, please request a quotation here.You may also buy this product personally in our showroom in Hamburg.Thinner 20-05 for SIGMARINE single component varnish and primers No. 24, 40, 42, 48, 49.

Orange terpene thinner/solvent.Especially intended for use with BIO PIN varnishes and oils.

Thinner 91-92 for SIGMA COVER 280 and SIGMA PRIME 200.

Balsam turpentine oil is a high-quality, pure natural product with strong dissolving power, obtained by distillation from the turpentine (balsam) of coniferous trees such as pinetrees. It is transparent, mildly scented, and suitable as a thinner for paints and varnishes based on oil and oil-alkyd resins. It can also be used to dissolve natural resins and oils. Application: The balsam turpentine oil can be added according to the paint manufacturer's instructions. Storage should be cool but frost-free. The container must always be tightly sealed.Safety instructions: The product is highly flammable and harmful if swallowed, in contact with skin, or if inhaled. Ensure good ventilation during use, avoid aerosol formation, and keep away from sources of ignition. Technical dataApplication area: Thinner for oil and oil-alkyd resin paintsSubstrate: depending on the paint system usedCoverage: depending on the type of paint and desired viscosityDrying times: depending on the paint usedFor further information on application, please refer to the technical data sheet under 'Downloads'.

PU special thinner for G4/G8 polyurethane resin.

White Spirit is a turpentine substitute and a mineral oil-based thinner. The product is used to thin paints based on oil and oil-alkyd resin, as well as a cleaning agent for parquet, linoleum, and brushes. It is characterized by consistent quality and good material compatibility.Application: The product is added to the respective paint and mixed. The maximum amount depends on the manufacturer's specifications of the respective paint. In addition, white spirit can be used to clean used painting tools such as brushes. Always close tightly after use and store in a cool, but frost-free place.Technical DataField of application: Thinner for paints based on oil and oil-alkyd resin; cleaning agent Substrate: Painted surfaces, used toolsCoverage: depends on the paint system and desired viscosityDrying times: depends on the paint system usedFurther information on processing can be found in the technical data sheet under 'Downloads'.

Spezialverdünner für YACHTCARE Antifoulings. Entwickelt zur Einstellung der Verarbeitungsviskosität und zur Reinigung von Werkzeugen nach der Verarbeitung.Anwendung: Nur für YACHTCARE Antifouling-Produkte verwenden. Dem Anstrichmaterial in kleinen Mengen zugeben, bis die gewünschte Viskosität erreicht ist. Nicht überdosieren, da dies die Schichtdicke und Trocknung beeinflussen kann. Auch geeignet zum Reinigen von Pinseln, Rollen und Spritzgeräten. Sicherheits- und Verarbeitungshinweise auf Gebinde und Sicherheitsdatenblatt beachten.Technische DatenAnwendungsbereich: Verdünnen und Reinigen bei YACHTCARE AntifoulingsKompatible Produkte: YACHTCARE ANTIFOULING SP (Art.Nr. 2520-701), YACHTCARE ANTIFOULING ACTION (Art.Nr. 2520-801)

This thinner is suitable for adjusting the YACHTCARE antifouling primer and for cleaning the tools.It should only be added to the antifouling primer if the primer is too viscous (e.g. at low temperatures).Also suitable for YACHTCARE 1-component coatings such as varnishes, primers and paints. It is used to adjust the processing viscosity and is also suitable for cleaning tools after use.Application: Only use with the YACHTCARE 1-component products intended for this purpose. Add in small quantities until the recommended viscosity is reached. Do not overdose in order not to impair drying and layer build-up. Also suitable for cleaning brushes, rollers and spraying equipment. Observe the safety and processing instructions on the container and safety data sheet.Technical dataArea of application: Dilution and cleaning of YACHTCARE 1-component coatingsCompatible products: YACHTCARE ANTIFOULING PRIMER (Art. 2520-012)

Special thinner for YACHTCARE epoxy resin systems. It is used to adjust the processing viscosity in epoxy coatings and is also suitable for cleaning tools after application.Application: Use only in combination with YACHTCARE epoxy resin products. Add in small amounts until the desired viscosity is achieved. Do not overdose, as this may impair curing and layer formation. Also suitable for cleaning brushes, rollers, and spray equipment. Observe safety and application instructions on the container and safety data sheet.Technical DataApplication area: Thinning and cleaning in connection with YACHTCARE epoxy resin productsCompatible products: YACHTCARE EPOXY PRIMER (Art.No. 2520-014)Application method: Add to the epoxy resin system according to manufacturer specifications; clean tools by rinsing with thinner