Boric wood impregnation BORACOL
Unfortunately, this product is no longer available. As an alternative, we recommend cleaning products from SIKA, YACHTCARE, EPIFANES, or OWATROL. You can find these below under “Similar Products.”
Boron salt-based wood preservative to combat and prevent mould, blue stain and bacteria in damp wood below deck, as well as algae, moss and mildew stains on the wooden deck.
Ready-to-use water-based solution, without outgassing organic solvents, therefore also suitable for indoor use.
This biocidal product should be used with care. Always read the label and product information before use. BAuA No. N-74326
€0.00*
€0.00
Description
Unfortunately, this product is no longer available. As an alternative, we recommend cleaning products from SIKA, YACHTCARE, EPIFANES, or OWATROL. You can find these below under “Similar Products.”
Boron salt-based wood preservative to combat and prevent mould, blue stain and bacteria in damp wood below deck, as well as algae, moss and mildew stains on the wooden deck.
Ready-to-use water-based solution, without outgassing organic solvents, therefore also suitable for indoor use.
This biocidal product should be used with care. Always read the label and product information before use. BAuA No. N-74326
Downloads
When purchasing biocidal antifoulings, private individuals with a German delivery address are required under the ChemBiozid-DV (Regulation (EU) No. 528/2012) to conduct a one-time telephone consultation before completing the purchase. This also applies to online purchases. Commercial customers and customers outside Germany are exempt from this obligation.
Here is how to proceed when purchasing a biocidal antifouling:
- You must be logged in as a customer
- Place the product in the shopping cart and proceed to checkout
- After receiving the order, you will receive an information email with all relevant details
- To conduct the consultation, please call Mon-Fri, between 9:00 am and 6:00 pm at the number +49 40 88901080. The conversation takes approx. 5 minutes.
Further information on biocidal products can be found here.
| CLP Regulation | |
|---|---|
| Symbols | 
|
| Signalword | Attention! |
| H phrases | H315, H319, H373, H412 |
| BAuA-Registriernummer | N-74326 |
Special cleaner and brightener for weathered and soiled wooden surfaces, especially teak decks. Also cleans GRP, gelcoat and particularly non-slip or textured deck coverings, removes yellowing and rust stains. Greyed teak decks regain their original wood tone, tannin-rich woods such as oak can be neutralized before recoating.OWATROL DECK CLEANER should be used to neutralize the wood after using alkaline deep cleaners such as DEEP CLEANER. The cleaner is based on oxalic acid and is biodegradable.Safety note: Wear chemical-resistant gloves, safety goggles and protective clothing when using.Application: Moisten absorbent substrates such as wood with water. Homogenize container by shaking. Apply evenly, then allow to act for 10-20 minutes. Ensure the surface remains wet during this time (e.g., with a garden hose). After the exposure time, rinse thoroughly with a brush or pressure washer to remove dirt from the pores. In heavily stained areas, repeat the application if necessary. Wait at least three days before further treatment with oils or varnishes (e.g., OWATROL DECK SEALER or AQUADECKS). Technical DataApplication area: Cleaning and brightening of greyed wood in outdoor areasSubstrate: untreated or oiled wood, moisten before applicationApplication: Brush, scrubber, sponge, watering can, sprayerCoverage: approx. 5–10 m²/l depending on degree of soilingThinning: undiluted or dilutable with water up to 1:5 Processing temperature: +5 °C to +35 °CDrying (20 °C): rinse off after 10–15 min., then allow wood to dry for 48 hrsFurther information on application can be found in the technical data sheet under "Downloads".
High-quality cleaning agent for teak and especially teak decks that are grouted, glued and sealed with SIKAFLEX.It removes dirt, salt residues and algae and at the same time brightens up grayed and weathered teak. It is also ideal for cleaning teak furniture. Complies with REACH guidelines and is biodegradable (EC 648/2004).Application: The wood to be treated should be soaked in water before use. Depending on the degree of soiling, the cleaner is worked in directly or diluted with water using a brush or an abrasive pad in the direction of the grain. After a short exposure time, the surface can then be rinsed with fresh water.
Deep-penetrating, solvent-free, water-based teak protectant.TEAK-O-BELLO offers long-holding protection for teak and other hardwoods preventing it from weathering and graying for an extended period of time. It's water-based, environmentally friendly formulation lasts longer than solvent-based teak oils and sealers and protects against the formation of mold.Contains no solvents and VOC's and doesn't attack the caulking sealant on teak decks. Dries to a matte finish.Coverage. approx. 5 - 12 sq.m/l.
Especially efficient, alkaline cleaner, which removes old and persistent dirt and traces of decay, as well as dissolving remains of old oil treatments of teak.This treatment is surface-friendly since the old coats of paint do not have to be sanded off. Afterwards the wood is clean and ready for subsequent conditioning like brightening with TEAK-BRIGHTENER 2 and maintenance with TEAK-OIL 3. - it cleans timber pores deep-down of dirt. - removes remains of former oil treatments from below the surface. - Stained surfaces regain their former homogeneous, uniform look from the treatment. Shade of colour: green shaded, milky transparent.Yield approx.. 200 ml/m².
Preventive, open-pored wood preservative against fungal decay and insect attacks of timber in the interior and outdoors as well as wood in humidors.Also suited for the restoration (solidification) of old timberPermeable for water vapour .Effective by obfuscation of the wood for vermin. Rubber gloves should be carried when applying.A recognised respiratory equipment should be carried when using a spray diffuser.Do not sand with steel wool, since the sanding dust can lead to black staining. The biopin Vertriebs GmbH produces innovative natural paints already in the fourth generation with the technical facilities of the present. The company manufactures wholesome products on the basis of natural raw materials.
Unfortunately, this product is no longer available. As an alternative, we recommend cleaning products from SIKA, YACHTCARE, EPIFANES, or OWATROL. You can find these below under “Similar Products.”Boron salt-based wood preservative to combat and prevent mould, blue stain and bacteria in damp wood below deck, as well as algae, moss and mildew stains on the wooden deck.Ready-to-use water-based solution, without outgassing organic solvents, therefore also suitable for indoor use.This biocidal product should be used with care. Always read the label and product information before use. BAuA No. N-74326
Penetrating oil based on natural oils, which is used as an additive to improve the flow properties of conventional and semi-synthetic paints. It reduces visible brush strokes, impregnates wood and has a rust-inhibiting effect on steel by penetrating deep into the substrate. This means that a favorable result can be achieved even under difficult conditions.
HEMPEL'S WOOD IMPREG is a clear alkyd oil with great penetration properties. It serves as a primer for hardwoods indoors and outdoors above the waterline. The oil penetrates deeply into the wood and ensures an even saturation of the substrate.Application: The surface must be clean, dry, and free of grease; the wood moisture content must not exceed 16%. HEMPEL'S WOOD IMPREG is applied with a brush in 2–4 wet-on-wet coats. Excess oil should be removed with a lint-free cloth to avoid film formation. Once dry, it can be overcoated with suitable Hempel paints. Thinning and cleaning should be done with HEMPEL'S THINNER 811 (Item No. 2577-026).Technical DataArea of application: Primer for wood saturation, indoors and outdoors above the waterlineSubstrate: Clean, dry, grease-freeCoverage: approx. 13 m²/l (depending on the porosity of the wood)Thinning: HEMPEL'S THINNER 811Application method: BrushDrying times (at 20 °C): Touch dry after approx. 6 h, re-coatable after full penetrationDurability: Until overcoated with paint; not a standalone topcoatFurther processing information can be found in the Technical Data Sheet under 'Downloads'.
IMP IMPREGNATING OIL is a transparent wood priming oil made from a drying alkyd resin oil. It is used for the care and preservation of dimensionally stable wooden components above the waterline in indoor and outdoor areas.Thanks to its excellent penetration properties, it acts preventively against rot and fungal infestation when saturating the wood, as air and moisture are displaced. It dries quickly, is vapor-permeable and water-repellent. Suitable as a saturating primer for further coatings such as BENAR oils and other single-component paints. For sole treatment (matte surface) of spars and masts, the "wet-on-wet" application is recommended until the wood is fully saturated. Suitable for all types of wood.Application: The product is ready to use and should not be diluted. Stir well before use. Application can be done with a brush or roller. The oil is applied wet-on-wet until the wood pores are fully saturated. Material that has not penetrated must be removed immediately with a clean, lint-free cloth. Clean tools with white spirit.Technical DataField of application: Care and preservation agent for wood above the waterline (indoor and outdoor)Substrate: Clean, dry, free of grease and dust; for new tropical woodsCoverage: approx. 3–6 m²/l (theoretical, depending on absorbency)Thinning: No spray dilution intendedApplication method: Brush, rollerDrying times (at 20 °C): Dust-dry after 5 hrs, re-coatable after at least 24 hrs (max. 3 months), fully loadable after 2 days
A highly effective impregnating oil that protects, beautifies and hardens wood. LE TONKINOIS BIO IMPRESSION is ideal for pre-treatment before varnishing, as it penetrates deep into the wood and unifies the absorption behavior of the wood surface through saturation. Made from pure natural oils (linseed oil, castor oil, palm oil) and free from harmful substances and solvents. The oil dries quickly, is abrasion-resistant after drying and provides a good base for further surface coating with varnishes such as LE TONKINOIS Vernis or LE TONKINOIS Marine No.1.Technical dataArea of application: Impregnating oil/primer for all types of wood indoors and outdoorsSubstrate pre-treatment: Sand wood, free of dust and grease, clean, dry and frost-freeApplication method: Brush, surface brushCoverage: approx. 20 m²/l, depending on substrate 30-50 ml/m² per coatDilution: Do not diluteDrying times at 20 °C: Dust-dry after 6-8 hours; can be recoated after approx. 12 hours.Ingredients: Linseed oil, tung oil, natural resins, isoaliphatesFurther information on processing can be found in the technical data sheet under "Downloads".
OWATROL DEKS OLJE D2 is a film-forming, high-gloss oil varnish that is applied as a top coat to wood surfaces treated with OWATROL DEKS OLJE D1.The coating forms a resistant, elastic varnish film that does not crack or flake off. Highly effective UV protection pigments ensure long-lasting protection. Particularly suitable for use on tropical hardwoods that are difficult to paint. Only use above water on all wooden surfaces that are not constantly exposed to water.Application: Apply three to six coats at intervals of at least 12 hours at 20° C. Do not sand between coats. Wipe up drips and runs immediately after application, as dried D2 oil is very difficult to remove completely. Allow to dry for at least three to four days, better a week before putting any load or stress on the surface. Technical DataApplication area: Wooden surfaces above waterline, interior/exteriorSubstrate: soft and hard woodsPre-treatment: Prime with OWATROL DEKS OLJE D.1; sand and degrease surfaceApplication: brush, rollerCoverage: approx. 12 m²/lThinner: noneDrying (20 °C): dust dry: 6 hrs, recoatable: 12 hrs, Loadable: 1 weekIngredients: alkyd-urethane resinsApplication temperature: 8°C to 35°CFurther information can be found in the technical data sheet under “Downloads”.
OWATROL DEKS OLJE D1 is a low-viscosity, transparent oil that is ideal for saturating wood, especially hardwoods and tropical woods. Due to its enormous penetrating capacity, it penetrates deep into the wood and displaces any moisture and air present. On the one hand, complete saturation prevents solid wood from working so that it no longer swells. On the other hand, the oil provides preventative protection against fungal and mold infestation. In the case of porous wood, treatment with D1 facilitates subsequent painting, as saturated wood absorbs less varnish or paint.OWATROL D1 can be applied to new, untreated wood or to wood that has already been weathered (with appropriate preparation). As a sole preservative, a permanently elastic, breathable, silky matt surface is achieved (e.g. for non-slip decks). OWATROL DEKS OLJE D2 is recommended as a film-forming further treatment. OWATROL D1 can also be painted over with 1-component primers and alkyd paints.Application: The product is applied in several coats until the wood is saturated. Then wait 15-20 minutes to allow the oil to soak in. Do not allow the oil to dry between coats, but work wet on wet. After the last coat, the surface should be wiped with a clean cloth after the waiting time to avoid the formation of a film.Important: To saturate wood in underwater areas, ensure that the wood is coated with a waterproof blocking primer (silver primer, CR primer). A recoating interval of at least one week (at 20°C) should be maintained between OWATROL D1 and primer, and correspondingly longer at cooler temperatures. It is also important to ensure that after the last coat of OWATROL Technical DataSubstrate: All wood types, including dense and oily hardwoods (e.g. teak, mahogany),Application area: interior and exteriorSurface preparation:Remove old coatings completelySand wood dry with 120 grit and clean (e.g. with denatured alcohol)For decks: sand with 40 grit, brush in grain direction using brass brush for slip resistanceTopcoat: Above water: OWATROL DEKS OLJE D2, 1component-PUR varnishes, alkyd-based coatings (test first); Below water: chlorinated rubber primer + antifoulingCoverage: 1–4 m²/l (initial saturation), 8–12 m²/l (maintenance)Thinner: None Application method: Flat brush, mohair roller, spray deviceDrying times at 20 °C: Fully cured after 3 daysFurther information on applying this product can be found in the technical data sheet under "Downloads".
OWATROL OIL, which is based on natural oils and has exceptionally good penetration properties, is the basic product for many applications.It is three times wetter than water, i.e. it even creeps upwards. On rusty metal, it creeps deep into the rust pores and displaces the air and moisture (i.e. the actual cause of corrosion) even from inaccessible areas. After drying, the leaf rust can be removed more easily and the soaked residual rust is consolidated, preserved and sealed for the long term and can be painted with all turpentine-substitute thinnable paints.For use on larger surfaces or as a paint additive, OWATROL is suitable for painting from the can.Technical dataSubstrates: Rusty and bare metals (iron, steel, aluminum), new and weathered woodPre-treatment: depending on the material: remove loose rust, non-adherent old paint, oil and grease
OWATROL OIL, which is based on natural oils and has exceptionally good penetration properties, is the basic product for many applications.It is three times wetter than water, i.e. it even creeps upwards. On rusty metal, it creeps deep into the rust pores and displaces the air and moisture (i.e. the actual cause of corrosion) even from inaccessible areas. After drying (24 hours at 20°C), the leaf rust can be removed more easily and the soaked residual rust is consolidated, preserved, sealed and can be painted with all turpentine substitute thinnable paints.OWATROL-OIL is also ideal as an additive (color additive) for 1-component paints. Instead of using turpentine substitute as a thinner, it significantly improves the coating and flow properties and ensures optimized adhesion without compromising the quality of the paint. On the contrary, the addition of 10-15% OWATROL OIL makes paints and varnishes even more porous and durable on the surface.OWATROL spray is suitable for minor touch-ups.Technical dataSubstrates: Rusty and bare metals (iron, steel, aluminum), new and weathered woodPre-treatment: depending on the material: remove loose rust, non-adherent old paint, oil and grease
Universal surface impregnation for many absorbent surfaces such as sails, tarpaulins or boat cushions, as well as transparent protection for natural stone and wood surfaces. The product does not build up, but is absorbed into the surface, is invisible and does not change the color of the treated surfaces. OMNISIDE INNOPERL is highly water, oil and dirt repellent (hydrophobic and oleophobic) and the treatment creates surfaces that are easy to clean.Made on the basis of fluoropolymers, solvent- and silicone-free, therefore suitable for indoor use. NOT SUITABLE for: Application on lime putty techniques in the facade area, leather.Application: The product can be applied with a brush, fur roller, cloth or pressure pump sprayer. After drying, there must be a pronounced water-repellent effect, otherwise repeat the application.Technical DataApplication area: absorbent and low-absorbent substrates, natural stone, plaster, exposed concrete, textiles (e.g. awnings, covers, cushions)Substrate: clean, dry, grease-free, not for constant water exposureApplication: brush, roller, cloth, pump sprayer, immersion methodCoverage: approx. 10 m²/lThinner: water, up to 1:2 dilution possibleApplication temperature: +10 °C to max. +25 °C (avoid direct sunlight)Drying (20 °C): dry after approx. 2 hrs, fully resistant after 24 hrsFurther information on application can be found in the Technical Data Sheet under "Downloads".
Deep-penetrating wood protection oil for pre-treatment of raw wood. RYLARD IMPREGNANTE serves both as a natural final treatment with an open-pored appearance and as a primer for further coatings with RYLARD varnishes. The product effectively protects the wood from natural damage such as fungi, mold, or insect infestation and is suitable for both indoor and outdoor use.Application: The surface should be clean, dry, and free of dust; old varnish layers must be removed beforehand. Two coats are required, at intervals of at least 12 hours. Application is done with a brush or spray gun. After the final coat, the desired topcoat can be applied after another 12 hours. Also suitable for wooden surfaces that have been stripped by sanding or hot air.RYLARD VarnishesThe Italian ship and yacht paint manufacturer BRAVA from Genoa offers with its RYLARD brand a range of traditional yacht varnishes, whose original formula was developed for the emerging yachting sport in the 19th century and is referred to on many classic yachts as the “Yachtman's Mirror.”Technical DataApplication area: Protection and priming for raw wood indoors and outdoorsSurface: Clean, dry, untreated woodCoverage: 15–20 m²/lThinning: White spirit substituteApplication method: Brushing or sprayingDrying times (at 20 °C): Dust-dry after 6 h, recoatable after 12 hFor more information on application, please refer to the technical data sheet under 'Downloads'.
RYLARD VG 61 DEFENDER is an oil-based wood primer for exterior use based on high-quality tung and linseed oils. The transparent drying primer impregnates the wood to make it water-repellent, enhances the grain, and provides preventive protection against rot and wood damage. It serves as a base coat on new wood or substrates sanded back to bare wood before coating with RYLARD varnishes. When applied in multiple coats, it forms a satin-matte, non-peeling protective film.Application: Suitable for exterior wood, including teak, wooden floors, pool surrounds, as well as yachts and heavily weather-exposed areas. Surfaces must be dry, clean, and free from dirt, dust, and sanding residues. Completely remove existing coatings. Sand bare wood with sandpaper (P 180–220). Stir well before use. Application temperature 10–35 °C. Apply at least 2 coats with a brush at intervals of 24 hours; intermediate sanding is not required. When applied outdoors, the coating must be completely dry before evening. Technical DataArea of application: Exterior use, especially wooden floors, teak, yachts, heavily weather-exposed wooden componentsSubstrate: Dry, clean, bare wood or wood sanded back to bare woodSubsequent coat: RYLARD clear varnishesCoverage: 15–20 m²/LThinning: White spiritApplication method: Brush; airless spraying (30:1, nozzle 0,009–0,011); conventional spraying (3–4 kg/cm², nozzle 1,4–1,7)Drying times (at 20 °C): dust-dry after 12 hrs.; recoatable after 24 hrs.Further information on application can be found in the technical data sheet under "Downloads".
OWATROL AQUADECKS is a water-based wood oil for indoor and outdoor use, used for impregnating and protecting soft and hardwoods. It penetrates deeply into the wood and provides a matte, open-pored surface that preserves the natural appearance. The oil is particularly suitable for decks, gangways, walkways, and similar applications on or onboard. It protects the wood from moisture and UV radiation and can be used on new, weathered, or already grayed wood.Application: For untreated wood, sand the wood surface if necessary, dust off, degrease or clean (see data sheet). Treat weathered wood with OWATROL NET-TROL (Art.No. 2508-001). Old coatings - except AQUADECKS coatings - must be removed. Application is done in two wet-on-wet coats without intermediate sanding. Wait 15-20 minutes between coats until the product is absorbed by the wood. After the second application, distribute or wipe off any excess product with a clean cloth after 20 minutes to avoid film formation and associated weakening of the properties. It can be applied with a brush, roller, or spray device. Tools can be cleaned afterwards with water and soap.Technical DataApplication area: Indoors and outdoors, e.g. terraces, teak decks, garden furnitureSubstrate: Hard and soft wood, tropical woods such as teak, ipe, bangkirai, merantiApplication: Brush, roller, spray deviceCoverage: approx. 10-12 m²/l (depending on wood type and absorbency)Thinning: noneApplication temperature: +10 °C to +30 °CDrying (20 °C): recoatable after 15–30 min., fully dried after 24–48 hrs.Further information on application can be found in the Technical Data Sheet under "Downloads".
