EPIFANES MULTI MARINE PRIMER is a universally applicable, quick-drying one-component primer with excellent adhesion properties. Suitable for use above the waterline on wood, fibreglass, steel, stainless steel, aluminium, galvanized metal, copper and most other bare or painted substrates.The primer can also be used as a tiecoat or adhesion promoter between a one- and two-component paint system.MULTI MARINE PRIMER offers exceptional hiding power, high build, good pore filling and corrosion protection on steel. Important: Stir well before application. Do not apply the coats wet-on-wet and observe the recoating interval. To ensure good adhesion between coats, we recommend sanding after each coat. Avoid too thick layers when painting to prevent drying problems. Must not be painted over with epoxy products (filler, primer, paint).Technical DataSubstrate: GRP, hard plastics, wood, steel, aluminium, zinc, galvanized metals, existing 1C/2C coatingsSurface preparation:GRP: degrease, sand dry with P220–280Steel: degrease, sand dry with P60Wood: degrease, sand dry with P220–240Aluminium: degrease, sand dry with P60; new aluminium: apply one coat of EPIFANES WASHPPRIMER AQExisting coatings: clean, sand with P240–280Can be overcoated with: Most one- and two-component products (see technical data sheet)Coverage: approx. 8–10 m²/l at 45 µm dry film thicknessThinner: EPIFANES Brush Thinner (brush), EPIFANES 1C Spray Thinner (spray), EPIFANES D-100 (airless)Application method: Brush, roller, spray gun, airless (professional users)Drying times at 10 °C: Dust dry after 2 hrs; recoatable after 12 hrs (1C), after 48 hrs (2C PU)Further information on application can be found in the technical data sheet under “Downloads”.

EPIFANES POLYURETHANE PRIMER is a hard 2-component polyurethane primer. The primer has excellent adhesion properties, fills small pores and scratches and ensures a smooth surface for subsequent final coating with colored EPIFANES POLY URETHANE paint. The primer fills the substrate well, is easy to apply with a roller or brush and is easy to sand.Area of application: Interior and exterior above the waterline, on untreated GRP or gelcoat. The primer also adheres to existing 2-component polyurethane or epoxy coatings above the waterline.Technical DataSubstrate: Gelcoat, epoxy coatings, existing old  2-component coatingsSurface preparation:GRP/Gelcoat: degrease, sand with P180Epoxy (HB/Primer): degrease, sand with P120–P180Old coatings: degrease, sand with P180–P220New aluminium: apply one coat of EPIFANES WASHPPRIMER AQTopcoat: EPIFANES Poly-urethane Varnish, for other paints see technical data sheetCoverage: approx. 10 m²/l at 35 µm dry film thicknessThinner: EPIFANES Poly-urethane Brush Thinner / Spray ThinnerApplication method: Brush, roller, spray gun (professional use)Drying times at 10 °C: Dust dry after 2 hrs; recoatable after 12 hrsFurther information on applying this product can be found in the technical data sheet under “Downloads”

EPIFANES RUST REMOVER is an acid-free rust converter based on water-displacing polymers that stops the rusting process. Provides a good primer for 1- and 2-component primers and paints above and below water. Before application, degrease the substrate and remove any loose rust, then apply only a thin layer.Important: RUST REMOVER is not a substitute for a primer and should be painted over within a minimum of 3 hours and a maximum of 48 hours (18°C).Technical dataSubstrates: Hand-rusted steel above and below the waterlinePre-treatment:Remove loose rust mechanically (e.g. with a wire brush or coarse sandpaper)Thoroughly degrease the substrate (e.g. with EPIFANES cleaning thinner)Follow-up coat: All 1K and 2K primers, paints and coatingsCoverage: approx. 20 m²/l with thin applicationDilution: Do not diluteApplication method: BrushDrying times at 18 °C: Can be painted over after at least 3 hours, at the latest after 48 hours.

EPIFANES WASHPRIMER AQ is a solvent-free, water-based one-component adhesive primer.Excellent adhesion to new aluminum, galvanized surfaces and non-ferrous metals, glass and ceramics.Use above and below the waterline, recoatable with all 1 and 2 component products. Apply only thinly without runners, do not sand.Tip: On existing coatings with corrosion damage, use EPIFANES MULTI-MARINE Primer as an adhesion primer.Technical DataSubstrate: Aluminium, hot/cold galvanized steel, zinc coatings, non-ferrous metals, stainless steel, glass, ceramicSurface preparation:Degrease with MEK, ammonia solution, or EPIFANES 1K Spray ThinnerRemove salts and dust, dry thoroughlyFor spray-galvanized surfaces: remove zinc salts with water and brushTopcoat: All 1C and 2C coatings (limitations for alkyds on zinc due to potential soap formation)Coverage: approx. 18 m²/l at 10 µm dry film thicknessThinner: NoneApplication method: Brush, spray gun (nylon or stainless steel nozzle), airlessDrying times at 20 °C: Dust dry after 15 min, recoatable after 2 hrs, max. 14 daysFurther application information can be found in the technical data sheet under “Downloads”.

WERDOL Primer Paint is a one-component, traditional primer for use on untreated wood. Good filling and covering properties for interior and exterior use. Suitable as a primer for one-component paint systems above the waterline. Can be overcoated with all EPIFANES one-component color paints.Technical DataSubstrate: Wood (above the waterline, interior and exterior)Surface preparation:Wood moisture max. 15–17 %Degrease oily wood with EPIFANES 1C Spray Thinner or special benzineSand with grit 60–80 along the grain, then with 100–220Remove sanding dust thoroughlyTopcoat: One-component alkyd-resin based paints Coverage: approx. 12 m²/l Thinner: EPIFANES Brush Thinner (brush/roller), EPIFANES 1C Spray Thinner (spray), EPIFANES D-100 (airless)Application method: Brush, roller, spray gun (professional use)Drying times at 20 °C: Dust dry after 2 hrs; recoatable after 24 hrsFurther information on processing can be found in the technical data sheet under “Downloads”.

WERDOL Bleimennige is a traditional, rust-preventing primer based on a modified linseed oil alkyd resin and a mixture of lead and iron oxide. Provides excellent rust protection on steel and has a rot-preventive effect on untreated wood. Nowadays it is mainly used for restoration work, as the lead oxide it contains is harmful to health and toxic to reproduction. Not suitable for use under water.This product may only be shipped to resellers, professional users and public research and teaching institutions in accordance with the Chemicals Prohibition Ordinance. Are you one of these customers? Then send us your inquiry here with a corresponding user certificate. We will be happy to provide you with a quotation.Technical dataSubstrates: Steel, iron, wood (above the waterline)Pre-treatment:Surface must be clean, dry and free of greaseRemove loose layers of rust and paintSubsequent coat: Single-component alkyd resin paints (e.g. EPIFANES boat paint, WERDOL Coasterlak)Coverage: approx. 12 m²/l with 50 µm dry film thicknessThinner: EPIFANES paint thinnerApplication method: Brush, rollerDrying times at 18 °C: Recoatable after 12 hours.Note: Contains lead. Do not use for painting objects that could be chewed or sucked by children. Contains cobalt carboxylate. May cause an allergic reaction.

Cathodic protecting zinc compound on the basis of polystyrene resin for rust free steel (by hand or machine) above the waterline or for zinc coated surfaces.More than 90% pure zinc in the drying coat.Yield: approx. 6 sq.m/l.

PAINT SYSTEM G4 Extra from Vosschemie is a solvent-based, one-component polyurethane resin. It hardens by releasing solvents and cross-links by absorbing moisture from the air and the substrate. This creates a wear-resistant film with high impact resistance.Field of application: G4 Extra is ideal as an adhesive primer for laminates with epoxy or polyester coatings. As a binder for wood flour, G4 Extra can also be used for the production of wood filler to fill chippings and wind cracks. It is also suitable as a particularly hard-wearing varnish for dark woods (e.g. mahogany). The coating has a yellowish-transparent coloration, which is intensified when exposed to UV light. VOSSCHEMIE polyurethane varnish G8 SUPER offers improved UV protection.Not suitable for use in interior areas (e.g. cabins).Coverage: approx. 100 ml/m² on non-absorbent and min. 200 ml/m² on absorbent substratesNote: Product contains hazardous chemicals according to REACH regulation. We recommend that it is only applied by professional users.Please read the application and safety instructions before using the product. These can be found on the product label and in the technical data sheet under “Downloads”.Technical DataSubstrate: Wood, concrete, screed, masonry, steel, GRPSurface preparation:Wood: sand with 80–120 gritConcrete/screed: dry, clean, oil-free, porous; mechanically open if neededGRP: dry, clean, optionally light sandingDo not apply on bituminous or solvent-sensitive surfacesTopcoat: 1C or 2C PU coatings, GRP laminatesCoverage: approx. 0.1 l/m² (non-absorbent), 0.2–0.25 l/m² (absorbent)Thinner: noneApplication method: Brush, roller, spray gun (only for professionals, use respiratory protection!)Drying times at 20 °C: can be painted over by itself: 2-4 hours (as soon as substrate is tack-free), max. 12 hours GRP: 0.5-4 hours (tacky)

HEMPEL LIGHT PRIMER is a high-quality 2-component epoxy primer for applications below and above the water. It can be used on rigid substrates as a barrier against penetrating water vapor, on GRP for osmosis prevention and repair, and on metal surfaces as corrosion protection. It can also be used on plywood and hardwood. Very suitable as an adhesion promoter for top coats and antifouling. Important: The sale of the 5-liter container 2577-057 is only possible to professional users. Are you one of these customers? Then order here to your company address. Personal collection from our store in Hamburg is also possible.Technical DataSubstrate: GRP, plywood, steel, aluminium, existing coatingsSurface preparation:GRP: sand, cleanPlywood: seal with suitable sealerSteel: high-pressure fresh water wash, sandblast or mechanically remove rust and cleanAluminium: non-metallic abrasive blasting, degreaseOld coatings: sand, clean, dryPorous surfaces: prime first coat of Light Primer with 20% thinnerTopcoat: standard 1K and 2K products (see data sheet)Coverage: 8.2 m²/l at 60 µm dry film thicknessThinner: HEMPEL'S THINNER 845Application method: Brush, roller, airless spray (professional use)Drying times at 10 °C: Dust dry after 6 hrs; recoatable after 9 hrsFurther information on application can be found in the technical data sheet under “Downloads”.

OWATROL CIP is a premium primer that combines the properties of a rust protection primer and an air-drying natural oil with a high solids content and exceptional penetration properties. Thanks to the OWATROL oil it contains, CIP has a low surface tension and is three times "wetter" than water. As a result, it wets substrates optimally and also penetrates into hard-to-reach corners that may not be mechanically derusted. It penetrates even thick layers of rust down to the "healthy" metal and displaces moisture and air. Dries completely, even in thick layers. It remains elastic after drying, but the added primer makes it hard enough to be coated with a subsequent one- or two-component anti-corrosion paint. Suitable for all areas that are exposed to extreme climatic conditions, such as ballast tanks.Technical DataSubstrate: Iron, steel, cast iron, stainless steel, light metals (bare or rusted)Surface preparation:Remove loose paint and rustFirm rust may remainSurface must be dry, grease-free and cleanFor chemically exposed surfaces: thorough cleaning with water or steamTopcoat: All one- or two-component systems including epoxy, polyurethane, chlorinated rubber etc.Coverage: up to 15 m²/l (depending on substrate and rust depth)Thinner: noneApplication method: Brush, lambskin roller, spray gun (professional use)Drying times at 20 °C: Touch dry after approx. 6 hrs; recoatable after 48 hrs.Further information on applying this product can be found in the technical data sheet under “Downloads”.Safety note: Cloths soaked with drying oils can self-ignite, therefore always spread out to dry before disposal or collect in sealed metal containers.

2-component epoxy primer containing zinc dust (67%) with high penetration properties, even on steel surfaces that have only been derusted by hand or water-blasted.This results in a very well adhering and robust cathodic corrosion protection layer. HANSAZINC ST tolerates residual moisture (no wetness) and slight flash rust formation.Can be painted over with 2-component paints, as well as with bitumen, vinyl and chlorinated rubber primers, but not with alkyd resin-based paints and paints containing zinc phosphate. Not suitable for use on galvanized, stainless, light or non-ferrous metals, wood, mineral substrates or plastics.Technical DataSubstrate: Steel, cast iron Surface preparation:Abrasive blasting Sa 2½High-pressure water blasting DW 3Manual derusting St 2 (up to 70 µm dry film even with residual rust/moisture)Topcoat:Recoatable with itself (max. total thickness 70 µm) without sandingRecoatable with two-component coatings after 4–14 days (intermediate sanding required)Antifoulings only with suitable intermediate coatingsCoverage: approx. 8-11.2 m²/l (depending on layer thickness)Thinner: HANSASOL EP thinnerApplication method: Brush, roller, airless spray, conventional spray gun (professional use)Drying times at 10 °C: Dust dry after approx. 3–4 hrs; recoatable after 4 hrs (recommended reference: 23 °C)Further information on applying the product can be found under “Downloads". 

PPG SIGMAFAST 20 thick-layered, modified alkyd resin zinc phosphate primer. Quick-drying, well adhering and opaque primer for all coatings with classic one-component paints above the water. Technical DataSubstrate: Steel Surface preparation:Remove rust by blasting or mechanical cleaningSurface must be clean, dry and dust-freeTopcoat: Compatible with most 1C and 2C coatings from PPG (see data sheet)Coverage: approx. 7.3 m²/l at 75 µm dry film thicknessThinner: THINNER 21-06 (airless/spray), THINNER 20-05 (brush/roller)Application method: Brush, roller, airless or conventional sprayDrying times at 20 °C: Touch dry after 15 min; recoatable after 45 min (with alkyd), after 8 hrs (with 2C products)Further information on processing the product can be found in the technical data sheet under “Downloads”. 

Fast drying, one component and good rust protection zinc phosphate thick film multiprimer for steel above the waterline. Easy to apply, surface tolerant, dries quickly and has great anticorrosicve properties. Can be recoated with various one and two component products.In accordance with the Chemicals Prohibition Ordinance, this product can only be shipped to resellers, professional users and public research and teaching institutes. Do you belong to this clientele? Then send us your inquiry here. We will be pleased to prepare a delivery offer for you. Private users can only be supplied in our store in Hamburg against proof of use.Technical DataSubstrate: SteelSurface preparation: Blast profile 40–70 µm, cleaned to ISO-Sa2½ or min. ISO-St2Topcoat: various products, e.g. SIGMARINE 48Coverage: approx. 7.3 m²/l at 75 µm dry film thicknessThinner: THINNER 21-06 Application method: Brush, roller, airless or conventional spray Drying times at 20 °C: Dust dry after 30 min; recoatable after 4 hrs Further information on applying this product can be found in the technical data sheet under "Downloads".

Universally applicable epoxy primer in protective coating systems for steel with excellent adhesion properties. SIGMACOVER 280 is a two-component, aluminum-pigmented, polyamide-cured universal primer for above-water applications. Suitable for corrosion protection of metal surfaces and as a primer for paint systems on decks and ballast tanks. Can be painted over with most alkyd resin, chlorinated rubber, vinyl and two-component epoxy resin and polyurethane coatings. Cures even at low temperatures (5°C).  Technical DataSubstrate: Steel, galvanized steel, stainless steel, aluminium, thermally sprayed metal (TSM), shop primer, concreteSurface preparation:Steel: Blast clean to ISO-Sa2½ (dry or wet), profile 30–75 µmGalvanized steel/stainless steel: Sweep blast per SSPC P-16Concrete: min. 28 days cured, max. 4.5% moisture, free from laitanceAll surfaces must be clean, dry and free of contaminantsTopcoat: 2C epoxy and polyurethane coatings (e.g. SIGMACOVER, SIGMADUR)Coverage: approx. 11.4 m²/l at 50 µm dry film thicknessThinner: THINNER 91-92 Application method: Brush, roller, airless or conventional sprayDrying times at 20 °C: Touch dry after 2 hrs, recoatable after 2 hrs, fully cured after 7 daysFurther information can be found in the technical data sheet under “Downloads”.

EURO LOCK Zinc Dust Paint offers high-quality corrosion protection for all metals, with a zinc content of approx. 95 % in the dry film. Suitable for touching up galvanized anchors, anchor chains and for repairing welding and sheet metal work (electrically conductive during welding). Prevents rust and offers good protection against extreme weather conditions. Temperature resistant up to 500 °C. Suitable as a single coating or as a primer for further top coats on systems exposed to water and weathering.&nbsp

High-quality corrosion protectant for all metals, heat resistant to 500°C. Zinc content approx. 95% in dry film. Also intended for refreshing galvanized anchors, anchor chains and for improvement of welds and sheet metal. Hinders rust and offers good protection against extreme weather influences. Can be painted over with most one- and two-part primers and paints.