EPIFANES MULTI MARINE PRIMER is a universally applicable, quick-drying one-component primer with excellent adhesion properties. Suitable for use above the waterline on wood, fibreglass, steel, stainless steel, aluminium, galvanized metal, copper and most other bare or painted substrates.The primer can also be used as a tiecoat or adhesion promoter between a one- and two-component paint system.MULTI MARINE PRIMER offers exceptional hiding power, high build, good pore filling and corrosion protection on steel. Important: Stir well before application. Do not apply the coats wet-on-wet and observe the recoating interval. To ensure good adhesion between coats, we recommend sanding after each coat. Avoid too thick layers when painting to prevent drying problems. Must not be painted over with epoxy products (filler, primer, paint).Technical DataSubstrate: GRP, hard plastics, wood, steel, aluminium, zinc, galvanized metals, existing 1C/2C coatingsSurface preparation:GRP: degrease, sand dry with P220–280Steel: degrease, sand dry with P60Wood: degrease, sand dry with P220–240Aluminium: degrease, sand dry with P60; new aluminium: apply one coat of EPIFANES WASHPPRIMER AQExisting coatings: clean, sand with P240–280Can be overcoated with: Most one- and two-component products (see technical data sheet)Coverage: approx. 8–10 m²/l at 45 µm dry film thicknessThinner: EPIFANES Brush Thinner (brush), EPIFANES 1C Spray Thinner (spray), EPIFANES D-100 (airless)Application method: Brush, roller, spray gun, airless (professional users)Drying times at 10 °C: Dust dry after 2 hrs; recoatable after 12 hrs (1C), after 48 hrs (2C PU)Further information on application can be found in the technical data sheet under “Downloads”.

EPIFANES POLYURETHANE PRIMER is a hard 2-component polyurethane primer. The primer has excellent adhesion properties, fills small pores and scratches and ensures a smooth surface for subsequent final coating with colored EPIFANES POLY URETHANE paint. The primer fills the substrate well, is easy to apply with a roller or brush and is easy to sand.Area of application: Interior and exterior above the waterline, on untreated GRP or gelcoat. The primer also adheres to existing 2-component polyurethane or epoxy coatings above the waterline.Technical DataSubstrate: Gelcoat, epoxy coatings, existing old  2-component coatingsSurface preparation:GRP/Gelcoat: degrease, sand with P180Epoxy (HB/Primer): degrease, sand with P120–P180Old coatings: degrease, sand with P180–P220New aluminium: apply one coat of EPIFANES WASHPPRIMER AQTopcoat: EPIFANES Poly-urethane Varnish, for other paints see technical data sheetCoverage: approx. 10 m²/l at 35 µm dry film thicknessThinner: EPIFANES Poly-urethane Brush Thinner / Spray ThinnerApplication method: Brush, roller, spray gun (professional use)Drying times at 10 °C: Dust dry after 2 hrs; recoatable after 12 hrsFurther information on applying this product can be found in the technical data sheet under “Downloads”

EPIFANES RUST REMOVER is an acid-free rust converter based on water-displacing polymers that stops the rusting process. Provides a good primer for 1- and 2-component primers and paints above and below water. Before application, degrease the substrate and remove any loose rust, then apply only a thin layer.Important: RUST REMOVER is not a substitute for a primer and should be painted over within a minimum of 3 hours and a maximum of 48 hours (18°C).Technical dataSubstrates: Hand-rusted steel above and below the waterlinePre-treatment:Remove loose rust mechanically (e.g. with a wire brush or coarse sandpaper)Thoroughly degrease the substrate (e.g. with EPIFANES cleaning thinner)Follow-up coat: All 1K and 2K primers, paints and coatingsCoverage: approx. 20 m²/l with thin applicationDilution: Do not diluteApplication method: BrushDrying times at 18 °C: Can be painted over after at least 3 hours, at the latest after 48 hours.

EPIFANES WASHPRIMER AQ is a solvent-free, water-based one-component adhesive primer.Excellent adhesion to new aluminum, galvanized surfaces and non-ferrous metals, glass and ceramics.Use above and below the waterline, recoatable with all 1 and 2 component products. Apply only thinly without runners, do not sand.Tip: On existing coatings with corrosion damage, use EPIFANES MULTI-MARINE Primer as an adhesion primer.Technical DataSubstrate: Aluminium, hot/cold galvanized steel, zinc coatings, non-ferrous metals, stainless steel, glass, ceramicSurface preparation:Degrease with MEK, ammonia solution, or EPIFANES 1K Spray ThinnerRemove salts and dust, dry thoroughlyFor spray-galvanized surfaces: remove zinc salts with water and brushTopcoat: All 1C and 2C coatings (limitations for alkyds on zinc due to potential soap formation)Coverage: approx. 18 m²/l at 10 µm dry film thicknessThinner: NoneApplication method: Brush, spray gun (nylon or stainless steel nozzle), airlessDrying times at 20 °C: Dust dry after 15 min, recoatable after 2 hrs, max. 14 daysFurther application information can be found in the technical data sheet under “Downloads”.