EV 100 Tiller Pilot Set RAYMARINE T70153

The 12-inch plotter from Raymarine's AXIOM+ series is a powerful, tried-and-tested GPS chart plotter that is easily operated via a touch display. The latter is very easy to read even in sunlight and around 25 percent brighter than the previous model series. It is ideal for navigation on sailing or motorboats and can display many other boat data. Whether wind information, echo sounder, AIS, radar, engine data or tank levels, they can either be integrated into the plotter image or displayed on split screens or separate dashboard pages. Particularly important data such as course, speed, depth or nearby vessels are always clearly displayed and the crew can easily keep track of everything. Fish finders from the RV 300 series can also be integrated.The AXIOM+ 12 is either flush-mounted in the equipment carrier on the helm or in the bulkhead, or mounted externally on the bracket supplied. It has an integrated GPS module for location and course data, but can also be optionally connected to an external GPS antenna. The display is water-repellent thanks to the HydroTech nano-coating and can therefore be operated even when wet. Alternatively, the additionally available RMK-10 external control panel with rotary control and buttons can also be fitted. With this combination, the plotter is still cheaper than the AXIOM PRO series, which has an integrated control panel. The AXIOM+ series offers plotters in 7, 9 and 12 inch sizes.The AXIOM+ runs the Lighthouse 4 operating system and can display either the Lighthouse chart sets developed by Raymarine or Navionics charts. The software scope also includes autorouting, which easily creates route suggestions for a selected destination. The laylines function is also very interesting for sailors, allowing them to determine the right time for tacking or jibing at the cross towards the destination. The polar data of your own ship can be stored in the plotter for this purpose, and many yacht models are already pre-installed. This means that maneuvers can be ideally planned and adapted to wind shifts.The AXIOM+12 is available as a bundle with the pre-installed Lighthouse chart sets for Northern Europe, Western Europe or the Mediterranean for a small surcharge. The sets are then significantly cheaper than buying them separately. The map set sections are shown in the pictures.Scope of delivery: Plotter, bracket holder, knurled screws, sun cover. Documentation, mounting gasket, rear mounting bracket, 4 threaded bolts, 4 wing nuts, NMEA/power supply cable 1.5 m, DeviceNet to SeaTalkng adapter cable 1.2 mTechnical specificationsDisplay: IPS widescreen - WXGA 1280 x 800Waterproof class IPX-7Power consumption: 18.96 WVoltage: 8-16 V DCDimensions bracket mounting: width: 314 mm (12.36 inches), height: 217 mm (8.54 inches), depth including cable: 178 mm (7.01 inches)Recessed mounting dimensions: width: 314 mm (12.36 inches), height: 226.72 mm (8.93 inches), depth including cable: 178 mm (7.01 inches)GPS: GPS, GLONASS, BeidouAccessories connection: USB micro BEthernet: RayNet (10/100 MBit/s)NMEA2000: DeviceNet (connector integrated in power cable) InternalAntenna: Ceramic chip is mounted near the top of the deviceBluetooth: V4.0, WLAN: 802.11/b/g/nInternal memory: 16 GB solid-state (14 GB usable)Encoder connections: 25-pin RealVision connector. Requires the A80490 adapter cable for CPT-S encodersExternal memory: MicroSDXC card slot x 1

The 7-inch plotter from Raymarine's AXIOM+ series is a powerful, tried-and-tested GPS chart plotter that is easily operated via a touch display. The latter is very easy to read even in sunlight and around 25 percent brighter than the previous model series. It is ideal for navigation on sailing or motorboats and can display many other boat data. Whether wind information, echo sounder, AIS, radar, engine data or tank levels, they can either be integrated into the plotter image or displayed on split screens or separate dashboard pages. Particularly important data such as course, speed, depth or nearby vessels are always clearly displayed and the crew can easily keep track of everything. Fish finders from the RV 300 series can also be integrated.The AXIOM+ 7 is either flush-mounted in a device carrier on the helm or recessed in the bulkhead, or mounted externally on the bracket supplied. It has an integrated GPS module for location and course data, but can also be optionally connected to an external GPS antenna. The display is water-repellent thanks to the HydroTech nano-coating and can therefore be operated even when wet. Alternatively, the additionally available RMK-10 external control panel with rotary control and buttons can also be fitted. With this combination, the plotter is still cheaper than the AXIOM PRO series, which has an integrated control panel. The AXIOM+ series offers plotters in 7, 9 and 12 inch sizes.The AXIOM+ runs the Lighthouse 4 operating system and can display either the Lighthouse chart sets developed by Raymarine or Navionics charts. The software scope also includes autorouting, which easily creates route suggestions for a selected destination. The laylines function is also very interesting for sailors, allowing them to determine the right time for tacking or jibing at the cross towards the destination. The polar data of your own ship can be stored in the plotter for this purpose, and many yacht models are already pre-installed. This means that maneuvers can be ideally planned and adapted to wind shifts.The AXIOM+7 is available as a bundle with the pre-installed Lighthouse chart sets for Northern Europe, Western Europe or the Mediterranean for a small surcharge. The sets are then significantly cheaper than buying them separately. The map set sections are shown in the pictures.Scope of delivery: Plotter, bracket holder, knurled screws, sun cover. Documentation, mounting gasket, rear mounting bracket, 4 threaded bolts, 4 wing nuts, NMEA/power supply cable 1.5 m, DeviceNet to SeaTalkng adapter cable 1.2 mTechnical specificationsDisplay: IPS widescreen - WSVGA 1024 x 600Waterproof class IPX-7Power consumption: 7.34 WVoltage: 8-16 V DCDimensions bracket mounting: width: 25.4 mm (9.86 inches), height: 162.5 mm (6.4 inches), depth including cable: 218 mm (8.58 inches)Dimensions recessed mounting: width: 201.1 mm (7.92 inches), height: 133 mm (5.24 inches), depth including cable: 218 mm (8.58 inches)GPS: GPS, GLONASS, BeidouAccessories connection: USB micro BEthernet: RayNet (10/100 MBit/s)NMEA2000: DeviceNet (connector integrated in power cable) InternalAntenna: Ceramic chip is mounted near the top of the deviceBluetooth: V4.0, WLAN: 802.11/b/g/nInternal memory: 16 GB solid-state (14 GB usable)Encoder connections: 25-pin RealVision connector. Requires the A80490 adapter cable for CPT-S encodersExternal memory: MicroSDXC card slot x 1

The 9-inch plotter from Raymarine's AXIOM+ series is a powerful GPS chart plotter that is operated via a touch display. The latter is also very easy to read in sunlight and is around 25 percent brighter than the previous model series. It is ideal for navigation on sailing or motor boats that also want to network additional data from sensors in the on-board network. Whether wind display, echo sounder, AIS, radar, engine or tank displays, the plotter can integrate particularly important data such as course, speed, depth and more into the plotter image or display it on split screens and its own dashboard pages. This makes it easy for the crew to maintain an overview at all times.The AXIOM+ has an integrated GPS module for location and course data, but can also be optionally connected to an external GPS antenna. The display is water-repellent thanks to the HydroTech nano-coating and can therefore be operated even when wet. If required, the external RMK-10 control panel with rotary control and buttons can also be fitted. The AXIOM+ series offers plotters in 7, 9 and 12 inch sizes.The AXIOM runs the Raymarine Lighthouse 4 operating system and can display either the Lighthouse chart sets developed by Raymarine or Navionics charts. The software scope also includes autorouting, which makes route suggestions for a selected destination with ease. The laylines function is also very interesting for sailors, allowing them to determine the right time to tack or jibe towards their destination. The polar data of your own ship can be stored in the plotter for this purpose. This allows maneuvers to be ideally planned and also adapted to wind shifts.The AXIOM+9 is available as a bundle with the pre-installed Lighthouse chart sets for Northern Europe, Western Europe or the Mediterranean for an additional 100 euros. The map set sections can be found in the images below.Quad-core processor-AIS possible-Navionics chartsRadarScope of delivery: Plotter, bracket holder, knurled screws, sun cover. Documentation, mounting gasket, rear mounting bracket, 4 threaded bolts, 4 wing nuts, NMEA/power supply cable 1.5 m, DeviceNet to SeaTalkng adapter cable 1.2 mTechnical specificationsDisplay: IPS widescreen - HD 1280 x 720, 1500Waterproof class IPX-7Power consumption: 8.95 WVoltage: 8-16 V DCBracket mounting dimensions: Width: 265.03 mm (10.43 inches), height: 187.81 mm (7.39 inches), depth including cable: 178 mm (7.01 inches)Flush mounting dimensions: width: 244.08 mm (9.64 inches), height: 157.78 mm (6.21 inches), depth including cable: 178 mm (7.01 inches)GPS: GPS, GLONASS, BeidouAccessories connection: USB micro BEthernet: RayNet (10/100 MBit/s)NMEA2000: DeviceNet (connector integrated in power cable) InternalAntenna: Ceramic chip is mounted near the top of the deviceBluetooth: V4.0, WLAN: 802.11/b/g/nInternal memory: 16 GB solid-state (14 GB usable)Encoder connections: 25-pin RealVision connector Requires adapter cable A80490 for CPT-S encoder

AXIOM2 is the next generation of RAYMARINE's tried-and-tested, robust chartplotter series. Thanks to their good readability in the sun, intuitive touch operation and robustness, they are rightly popular with many skippers and owners. The plotters can be easily networked with transducers for depth, wind, speed and displays such as the i70 and are enormously expandable with connections for autopilots, AIS, radar, engine data cameras or on-board sensors. The data can either be integrated into the plotter image or displayed on split screens or separate dashboard pages. This makes it easy for the crew to maintain an overview. Chart sets from Raymarine's own Lighthouse standard can be displayed, as well as alternatives from Navionics or C-Map.The technical upgrade of the AXIOM2 to the previous Axiom+ version scores points with a faster 6-core processor, which makes starting, zooming and switching even smoother. The RAM has also been increased from 16 to 64 gigabytes. The robust HydroTough™ touch display also offers enhanced app and motor data integration. Important: The new plotters have the same installation dimensions as the previous Axiom+ series, so they fit into the existing cut-outs on board!In addition, the plotter will run with the new Lighthouse 5 operating system from Raymarine from mid-2025; the old plotters in the AXIOM+ series will not be updated and will continue to run on the older version 4. Raymarine offers a 3-year warranty!The AXIOM2 is available as a bundle with Lighthouse chart sets for Northern Europe, Western Europe or the Mediterranean for a small surcharge. The sets are then significantly cheaper than if they are purchased separately at a later date. The map set sections are shown in the pictures.Scope of delivery: Chart plotter, swivel bracket, knobs for bracket, gasket for surface mounting, sunshade, M3x5 screw, M3 spring washer and M3 crimp connector, 4 x M5 x 58 grub screws, 4x M5 wing nuts, instructions, DeviceNet-to-SeaTalk-NG adapter cable, 120 mm (4.7 in), power/NMEA-2000 cable (with 1.5 m (4.92 ft) power connection and 0.5 m (1.64 ft) NMEA-2000 connection).Technical dataDisplay: IPS widescreen - HD 1280 X 720Waterproof class IPX-7Power consumption (max): 17.64 WVoltage: 8-16 V DCBracket mounting dimensions: Width: 265.03 mm (10.43 inches), height: 187.81 mm (7.39 inches), depth including cable: 178 mm (7.01 inches)Recessed mounting dimensions: width: 244.08 mm (9.64 inches), height: 157.78 mm (6.21 inches), depth including cable: 178 mm (7.01 inches)GPS: GPS, GLONASS, Beidou, 10HzEthernet: RayNet (10/100/1000 MBit/s)NMEA2000: DeviceNet (connector integrated in power cable) InternalBluetooth: V4.0, WLAN: 802.11/b/g/nInternal memory: 64 GBEncoder connections: (RV models only!) 25-pin RealVision connector. Requires adapter cable A80490 for CPT-S encodersExternal memory: MicroSDXC card slot x 1compatible sensors: Radar, autopilot, sonar module, AIS transceiver, thermal imaging cameras and visible light cameras,VHF radios, engine integration, digital switching, assisted docking, augmented reality,Instruments, ship monitoring

AXIOM2 is the next generation of RAYMARINE's tried-and-tested, robust chartplotter series. Thanks to their good readability in the sun, intuitive touch operation and robustness, they are rightly popular with many skippers and owners. The plotters can be easily networked with transducers for depth, wind, speed and displays such as the i70 and are enormously expandable with connections for autopilots, AIS, radar, engine data cameras or on-board sensors. The data can either be integrated into the plotter image or displayed on split screens or separate dashboard pages. This makes it easy for the crew to maintain an overview. Chart sets from Raymarine's own Lighthouse standard can be displayed, as well as alternatives from Navionics or C-Map.The technical upgrade of the AXIOM2 to the previous Axiom+ version scores points with a faster 6-core processor, which makes starting, zooming and switching even smoother. The RAM has also been increased from 16 to 64 gigabytes. The robust HydroTough™ touch display also offers extended app and motor data integration. Important: The new plotters have the same installation dimensions as the previous Axiom+ series, so they fit into the existing cut-outs on board!In addition, the plotter will run with the new Lighthouse 5 operating system from Raymarine from mid-2025; the old plotters in the AXIOM+ series will not be updated and will continue to run on the older version 4. Raymarine offers a 3-year warranty!The AXIOM2 is available as a bundle with Lighthouse chart sets for Northern Europe, Western Europe or the Mediterranean for a small surcharge. The sets are then significantly cheaper than if they are purchased separately at a later date. The map set sections are shown in the pictures.Scope of delivery: Chart plotter, swivel bracket, knobs for bracket, gasket for surface mounting, sunshade, M3x5 screw, M3 spring washer and M3 crimp connector, 4 x M5 x 58 grub screws, 4x M5 wing nuts, instructions, DeviceNet to SeaTalk NG adapter cable, 120 mm (4.7 in), power/NMEA 2000 cable (with 1.5 m (4.92 ft) power connection and 0.5 m (1.64 ft) NMEA 2000 connection).Technical dataDisplay: IPS widescreen - WSVGA 1024 x 600Waterproof class IPX-7Power consumption (max): 16.56 WVoltage: 8-16 V DCBracket mounting dimensions: Width: 250.4 mm (9.86 inches), height: 162.5 mm (6.4 inches), depth including cable: 218 mm (8.58 inches)Dimensions recessed mounting: width: 201.1 mm (7.92 inches), height: 133 mm (5.24 inches), depth including cable: 218 mm (8.58 inches)GPS: GPS, GLONASS, Beidou, 10HzEthernet: RayNet (10/100/1000 MBit/s)NMEA2000: DeviceNet (connector integrated in power cable) InternalBluetooth: V4.0, WLAN: 802.11/b/g/nInternal memory: 64 GBEncoder connections: (RV models only!) 25-pin RealVision connector. Requires adapter cable A80490 for CPT-S encodersExternal memory: MicroSDXC card slot x 1compatible sensors: Radar, autopilot, sonar module, AIS transceiver, thermal imaging cameras and visible light cameras,VHF radios, engine integration, digital switching, assisted docking, augmented reality,Instruments, ship monitoring

Komplettes Instrument/Geber-Paket für die Anzeige von Winddaten, Tiefe- und Geschwindigkeit, basierend auf einem RAYMARINE i70s Display. Zum Set gehört der Geber DST 800 der Logge, Lot und Temperaturmesser in einem ist. Weiterhin die Wind-Masteinheit samt 30 m Kabel dabei, der ITC-5 Konverter für die analogen Geber-Eingäng, sowie die für das SeatalkNG-Netzwerk nötigen 5-Wege Connector mit 3 Metern-Backbone-Kabel und Endwiederständen. Alternativ gibt es für Eigner, die Logge und Lot in eigenen, getrennten Gebern haben möchte ein Bundle mit zwei Gebern gegen Aufpreis.Das Set ist damit eine komplett in sich geschlossene Lösung, das auch mit einem an Bord schon vorhandenen NMEA2000 oder älteren Seatalk Komponnennten (z.B. Autopiloten, Plotter u.ä.) verbunden werden kann. Dafür ist ein SeaTalkNG auf NMEA-2000 Konverter-Kabel nötig.Das Instrument i70s ist ein bewährtes, sehr vielseitiges Multifunktionsdisplay das fast alle Daten aus dem SeaTalkNG oder NMEA2000 Bord-Netzwerk anzeigen kann. Speed, Kurs, Winddaten, Tiefe, Tankanzeigen, Motordaten, AIS - es gibt kaum Informationen, die es nicht optisch klar und strukturiert darstellen kann. Die RAYMARINE-Bedienoberfläche "Lighthouse 4"  erlaubt eine einfache Installation und  Darstellung der Schiffsdaten über 7 vorkonfigurierte, intuitive optische Screens in Analog-Instrumenten-Optik. Darunter solche zu Kurs und Geschwindigkeit, Winddaten wie AWA,  TWA, Navigationsdaten, Tiefe , Heading. Auch Motor-Messdaten wie Umdrehungen, Wassertemperatur usw. sind darstellbar. Alternativ können Split-Screens mit bis zu sechs Info-Blöcken selbst völlig frei konfiguriert werden. Zudem können Alarme eingestellt werden, etwa für Tiefe, AIS, Kühlwassertemperatur.   Vier Tasten erlauben die einfache Bedienung, indem durch die Screens geklickt wird.  Auch mit Handschuhen und bei Regen oder Spritzwasser gibt es so keinerlei Probleme in der Bedienbarkeit.  Menü-Steuerung und Display-Helligkeitsregelung werden über den An/Aus- Knopf bedient. Dort wird auch auf den dimmbaren Nachtmodus umgeschaltet. Sehr gut in der Sonne ablesbares 4'1 Zoll-TFT-Display. Lieferumfang1x i70s Multifunktionsdisplay1x Wind-Masteinheit mit kurzem Arm mit 30m Kabel1x Logge/Lot/Temp-Geber DST 8001x iTC-5 Konverter2x SeaTalk NG Endwiderstand1x SeaTalk NG 5-Wege-Verbinder1x SeaTalk NG Backbone-Kabel / 3 m1x SeaTalk NG Stromkabel / 2 m2x SeaTalk NG Spur-Blindstecker

Proven, highly versatile multifunctional display that can show almost all data from the SeaTalkNG or NMEA2000 on-board network. Speed, course, wind data, depth, tank gauges, engine data, AIS - there is hardly any information that the i70s cannot display in a clear and structured way. Analog transducers from log/sounder, wind, etc. can also be integrated via an ITC-5 converter. Older RAYMARINE devices can also be connected via a converter.The RAYMARINE "Lighthouse 4" user interface allows easy installation and display of the ship's data via 7 preconfigured, intuitive visual screens in an analog instrument look. These include heading and speed, wind data such as AWA, TWA, navigation data, depth and heading. Engine measurement data such as rpm, water temperature etc. can also be displayed. Alternatively, split screens with up to six info blocks can be freely configured. Alarms can also be set, for example for depth, AIS and cooling water temperature.Four buttons allow easy operation by clicking through the screens, so there are no problems with usability even when wearing gloves and in the rain or splash water. Menu control and display brightness control are operated via the on/off button. This also switches to the dimmable night mode. The 4'1" TFT display is very easy to read in the sun.For connection to existing NMEA networks, a Seatalk-NMEA2000 converter plug from Raymarine or a Seatalk starter kit for multiple connections is required.Scope of delivery: i70s display with key pad and black cover frame, sun cover, SeaTalkNG track cable 40 cm (15.7 inch), seal, four M3x16 flat head pozi fastening screws, documentation.Technical data4.1-inch TFT LCD displayWaterproof to IPX6Mains voltage: 12 VVoltage: 9 to 16 V DC (protected up to 32 V DC)Power consumption: 1.7 WInterface: 1 x SeaTalkng (NMEA 2000 compatible)

The Bluetooth-based RCU-1 remote control allows you to operate all Raymarine EV-generation autopilots from anywhere on board. Ideal for maneuvers or sail changes on deck and for solo sailors. Just as you’re used to on the cockpit display, you can easily change course in 1- or 10-degree increments. The Point and Go feature is brand new: simply point the control unit in a direction or at a target and steer in that direction with the push of a button. You can preset via software how long this course should be steered.A brand-new safety feature is the available Solo Sailor mode: If the skipper (or a crew member) goes overboard with the remote control, causing the connection between the base station and the RCU to be lost, the RCU steers the boat into the wind. This requires a system with a wind sensor installed. Note: The Point and Go and Solo Sailor functions only work in conjunction with an Axiom chartplotter on board running at least Lighthouse version 4.11 or higher.The RCU is operated in conjunction with the WG-1 base station, which feeds the remote control’s Bluetooth signals into the onboard network via an NMEA2000/Device Net connection and can be installed below deck. The system’s range corresponds to the range of the Bluetooth network established between the base station and the RCU-1.The remote control runs on 2 AA batteries, which, according to the manufacturer, should last about 30 days depending on usage. In addition to autopilot data, the display can also show course, speed, depth, wind, or waypoint information if compatible Raymarine hardware such as an Axiom chartplotter or wind sensor is on board. The RCU-1 features a built-in compass, 3-axis accelerometer, 3-axis magnetometer, and 3-axis gyroscope.Note: The RCU-1 is not compatible with older autopilots from the SPX and X-Series, or older Seatalk1 devices.RCU-1 Technical SpecificationsDimensions: 150.87 mm x 59.83 mm x 31.51 mmWeight: 190 gWater resistance rating: IP 67Battery: AA alkaline, lithium, or rechargeable batteriesBluetooth range: 30 m with clear line of sight. WG-1Dimensions: 26.61 x 108.48 mm xWeight: 129 gProtection class: IPX6, IPX7IncludedRCU-1WG1 gateway6m NMEA2000 cable1m Seatalk NG to DeviceNet cable2 batteriesWall mountCarrying strap

Das Bedienpanel RMK-10 kann als Fernbedienung für Raymarine Plotter/Multifunktions-Displays benutzt werden und kann so entweder als Ergänzung für die ausschließlich per Touch bedienten Geräte, wie die der Axiom+ oder Axiom2- Serie benutzt werden oder als Zweit- oder Fernbedienung. Die Montage kann direkt neben dem Display oder weiter entfernt erfolgen, etwa am Steuerstand, Niedergang oder Flybridge erfolgen.Durch das RMK-10 kann ein reines Touch-Display vor allem im Cockpit auch bei starkem Regen, Gischt oder wenn die Crew Handschuhe trägt, jederzeit benutzt werden. Das RMK-10 kann senkrecht oder waagerecht montiert werden, zum Lieferumfang gehören entsprechend zwei unterschiedliche Abdeckungen für die Tasten. Ebenfalls enthalten sind ein 2-Meter-Kabel für die Stromzufuhr und ein weiteres zur Datenverbindung zum Raymarine-Gerät.   Lieferumfang: RMK-10, Tastaturabdeckung im Hochformat (vormontiert), Tastaturabdeckung im Querformat, Dichtung, Rechtwinkliges Stromkabel, 2 m, Raynet Netzwerkkabel 2m, 4x Befestigungsschrauben, Anleitung.Technische DatenStromversorgung: 12 oder 24 V, alternativ PoE: 48 V GleichstromStromverbrauch: Max. 4 W bei aktiver TastaturbeleuchtungSchutzklasse: IPX 6/ IPX 7Anschlüsse: 1y Raynet 10/100 MB/s, 1x Stromanschluss (SeatalkNG) 

The set contains all the necessary components to set up a small SeaTalkNG network on board. The 5-way connector acts as a short backbone to connect your new SeaTalkNG device via a trace cable (white-black). The supplied power cable supplies the backbone with power from the battery, and the two blue end resistors close the circuit.This allows a new Raymarine device to be put into operation or connected to other devices in an existing network. To connect to an existing NMEA 2000 network on board, a converter from SeaTalkNG to NMEA 2000 standard is also required.Scope of delivery1 x 5-way connector2 x end resistors1 x 3m SeaTalk track cable1 x SeaTalk power cable

The adapter cable allows Raymarine devices, or their backbone, with SeatalkNG data format to be fed into an NMEA2000 system/backbone. Raymarine backbone adapter cables can always be recognized by the blue plug/line color. It is plugged into a corresponding blue slot in the cabling of the new device and the NMEA2000 plug into a branch of the on-board network.The cable is 40 cm long.Note: If a Seatalk starter kit with 5-way distributor is installed, one end resistor must first be removed when fitting the adapter cable and the adapter plugged into the blue port.

AXIOM2 is the next generation of RAYMARINE's tried-and-tested, robust chartplotter series. Thanks to their good readability in the sun, intuitive touch operation and robustness, they are rightly popular with many skippers and owners. The plotters can be easily networked with transducers for depth, wind, speed and displays such as the i70 and are enormously expandable with connections for autopilots, AIS, radar, engine data cameras or on-board sensors. The data can either be integrated into the plotter image or displayed on split screens or separate dashboard pages. This makes it easy for the crew to maintain an overview. Chart sets from Raymarine's own Lighthouse standard can be displayed, as well as alternatives from Navionics or C-Map.The technical upgrade of the AXIOM2 to the previous Axiom+ version scores points with a faster 6-core processor, which makes starting, zooming and switching even smoother. The RAM has also been increased from 16 to 64 gigabytes. The robust HydroTough™ touch display also offers extended app and motor data integration. Important: The new plotters have the same installation dimensions as the previous Axiom+ series, so they fit into the existing cut-outs on board!In addition, the plotter will run with the new Lighthouse 5 operating system from Raymarine from mid-2025; the old plotters in the AXIOM+ series will not be updated and will continue to run on the older version 4. Raymarine offers a 3-year warranty!The AXIOM2 is available as a bundle with Lighthouse chart sets for Northern Europe, Western Europe or the Mediterranean for a small surcharge. The sets are then significantly cheaper than if they are purchased separately at a later date. The map set sections are shown in the pictures.Scope of delivery: Chart plotter, swivel bracket, knobs for bracket, gasket for surface mounting, sunshade, M3x5 screw, M3 spring washer and M3 crimp connector, 4 x M5 x 58 grub screws, 4x M5 wing nuts, instructions, DeviceNet-to-SeaTalk-NG adapter cable, 120 mm (4.7 in), power/NMEA-2000 cable (with 1.5 m (4.92 ft) power connection and 0.5 m (1.64 ft) NMEA-2000 connection).Technical dataDisplay: IPS widescreen - WXGA 1280 X 800Waterproof class IPX-7Power consumption (max): 20.64 WVoltage: 8-16 V DCBracket mounting dimensions: Width: 314.0 mm (12.36 inches), height: 226.72 mm (8.93 inches), depth including cable: 178 mm (7.01 inches)Dimensions recessed mounting: width: 314.08 mm (12.36 inches), height: 217.0 mm (8.54 inches), depth including cable: 178 mm (7.01 inches)GPS: GPS, GLONASS, Beidou, 10HzEthernet: RayNet (10/100/1000 MBit/s)NMEA2000: DeviceNet (connector integrated in power cable) InternalBluetooth: V4.0, WLAN: 802.11/b/g/nInternal memory: 64 GBEncoder connections: (RV models only!) 25-pin RealVision connector. Requires adapter cable A80490 for CPT-S encodersExternal memory: MicroSDXC card slot x 1compatible sensors: Radar, autopilot, sonar module, AIS transceiver, thermal imaging cameras and visible light cameras,VHF radios, engine integration, digital switching, assisted docking, augmented reality,Instruments, ship monitoring