2092-075 BENAR - Öl UVR glänzend
2092-003 BENAR - Öl UVR glänzend
BENAR UVR Wood Oil
BENAR UVR is a high-gloss wood oil based on long oil alkyd resin with an additional red-brown pigmented UV filter for outdoor use. It was specially developed for tropical and European hardwoods such as teak, mahogany or oak and forms an elastic, breathable protective film with very good weather resistance. The high vapor permeability prevents moisture from being trapped under the varnish film and thus prevents rotting. The high elasticity  
from €39.90*
Content:
0.7519
(€53.07* / 1 Liter)
€39.90*
Content:
0.7519 Liter
(€53.07* / 1 Liter)
Prices incl. VAT plus shipping costs
Description
BENAR UVR is a high-gloss wood oil based on long oil alkyd resin with an additional red-brown pigmented UV filter for outdoor use. It was specially developed for tropical and European hardwoods such as teak, mahogany or oak and forms an elastic, breathable protective film with very good weather resistance. The high vapor permeability prevents moisture from being trapped under the varnish film and thus prevents rotting. The high elasticity  
Downloads
Questions about the product?
Talk to craftsmen, boat builders and sailors. We understand your questions and provide the right answers.
Contact experts
Legal information about the product
| CLP Regulation | |
|---|---|
| Symbols | 
|
| Signalword | Danger! |
| H phrases | H319, H315, H317, H372, H410 |
| P phrases | P102, P260, P280, P273, P391, P333+P313, P305+P351+P338, P501 |
IMP fungicidal impregnating oil
From
€37.90 *
IMP IMPREGNATING OIL is a transparent wood priming oil made from a drying alkyd resin oil. It is used for the care and preservation of dimensionally stable wooden components above the waterline in indoor and outdoor areas.Thanks to its excellent penetration properties, it acts preventively against rot and fungal infestation when saturating the wood, as air and moisture are displaced. It dries quickly, is vapor-permeable and water-repellent. Suitable as a saturating primer for further coatings such as BENAR oils and other single-component paints. For sole treatment (matte surface) of spars and masts, the "wet-on-wet" application is recommended until the wood is fully saturated. Suitable for all types of wood.Application: The product is ready to use and should not be diluted. Stir well before use. Application can be done with a brush or roller. The oil is applied wet-on-wet until the wood pores are fully saturated. Material that has not penetrated must be removed immediately with a clean, lint-free cloth. Clean tools with white spirit.Technical DataField of application: Care and preservation agent for wood above the waterline (indoor and outdoor)Substrate: Clean, dry, free of grease and dust; for new tropical woodsCoverage: approx. 3–6 m²/l (theoretical, depending on absorbency)Thinning: No spray dilution intendedApplication method: Brush, rollerDrying times (at 20 °C): Dust-dry after 5 hrs, re-coatable after at least 24 hrs (max. 3 months), fully loadable after 2 days
BENAR glossy wood oil
From
€35.90 *
Current delivery notice: BENAR OIL CLEAR is currently not available. Please switch to alternative products such as BENAR UVR (2092-750) or varnish oils from OWATROL, LE TONKINOIS or EPIFANES.BENAR GLOSS is a high-gloss wood oil based on long-oil alkyd resin for the care and preservation of tropical and domestic hardwoods. The product forms an elastic, breathable protective film with good water vapor permeability and is suitable for use on surfaces with low UV exposure indoors and outdoors. The amber-colored varnish oil penetrates deeply into the wood and provides long-lasting protection against weathering. The high elasticity of the varnish oil additionally prevents flaking or chipping. This makes BENAR oil also very well suited for "working" solid woods. Application: Apply with a brush to clean, dry, grease-free surfaces. For highly absorbent and fungus-prone woods, a prior impregnation with IMP Impregnation Oil (Art.No. 2090-001) is recommended. Apply the first coat thinned (max. 15% white spirit substitute), further coats unthinned. Then apply at least three more unthinned coats outdoors (three coats are sufficient indoors). If a matte surface is desired, BENAR OIL MATT (Art.No. 2094-750) must be applied as the final coat. For soft and light-sensitive woods and for horizontal surfaces exposed to strong sunlight outdoors, we recommend BENAR OIL UVR (Art.No. 2092-003).Technical DataApplication area: Wood protection oil for indoor and outdoor useSubstrate: Clean, dry, load-bearing; max. 18% wood moisturePrimer: IMP Impregnation OilCoverage: 14–16 m²/l per coatThinning: White spirit substitute (only for first coat)Application method: Brush or airless (professional users)Drying times (at 23 °C): Dust-dry after approx. 6 hrs, recoatable after 24 hrsSafety note: Always use personal protective equipment during application. Further information on application can be found in the Technical Data Sheet under 'Downloads'.The shipping of this product is only possible in accordance with the Chemicals Prohibition Ordinance to resellers, professional users and public research and educational institutions.Do you belong to this customer group? Then send us your request here. We will gladly prepare a delivery offer for you.For private users, delivery is only possible in our Hamburg store against proof of use.
BENAR matte wood oil
€39.90 *
BENAR MATT is a clear wood oil based on long-oil alkyd resin for achieving a matte finish as a final coat on other BENAR products such as BENAR GLOSS (Art.No.2091-003). The product forms a matte, breathable protective film with good water vapor permeability and is suitable for use on surfaces with little UV exposure, both indoors and outdoors. Application: Apply with a brush on clean, dry, grease-free surfaces. Technical DataArea of application: matte wood protection oil for indoor and outdoor useSubstrate: surfaces coated with BENARCoverage: 14-16 m²/l per coatThinning: noneApplication method: brush or airless (professional users)Drying times (at 23 °C): dust-dry after approx. 6 hrs, recoatable after 24 hrsSafety Note: Always use personal protective equipment during application. For more information on application, please refer to the Technical Data Sheet under 'Downloads'.The shipment of this product is only possible to resellers, professional users, and public research and educational institutions in accordance with the Chemicals Prohibition Ordinance.Are you part of this customer group? Then send us your inquiry here. We will be happy to provide you with a delivery offer.For private users, sale is only possible in our retail store in Hamburg upon proof of intended use.
BENAR glossy wood oil
From
€35.90 *
Current delivery notice: BENAR OIL CLEAR is currently not available. Please switch to alternative products such as BENAR UVR (2092-750) or varnish oils from OWATROL, LE TONKINOIS or EPIFANES.BENAR GLOSS is a high-gloss wood oil based on long-oil alkyd resin for the care and preservation of tropical and domestic hardwoods. The product forms an elastic, breathable protective film with good water vapor permeability and is suitable for use on surfaces with low UV exposure indoors and outdoors. The amber-colored varnish oil penetrates deeply into the wood and provides long-lasting protection against weathering. The high elasticity of the varnish oil additionally prevents flaking or chipping. This makes BENAR oil also very well suited for "working" solid woods. Application: Apply with a brush to clean, dry, grease-free surfaces. For highly absorbent and fungus-prone woods, a prior impregnation with IMP Impregnation Oil (Art.No. 2090-001) is recommended. Apply the first coat thinned (max. 15% white spirit substitute), further coats unthinned. Then apply at least three more unthinned coats outdoors (three coats are sufficient indoors). If a matte surface is desired, BENAR OIL MATT (Art.No. 2094-750) must be applied as the final coat. For soft and light-sensitive woods and for horizontal surfaces exposed to strong sunlight outdoors, we recommend BENAR OIL UVR (Art.No. 2092-003).Technical DataApplication area: Wood protection oil for indoor and outdoor useSubstrate: Clean, dry, load-bearing; max. 18% wood moisturePrimer: IMP Impregnation OilCoverage: 14–16 m²/l per coatThinning: White spirit substitute (only for first coat)Application method: Brush or airless (professional users)Drying times (at 23 °C): Dust-dry after approx. 6 hrs, recoatable after 24 hrsSafety note: Always use personal protective equipment during application. Further information on application can be found in the Technical Data Sheet under 'Downloads'.The shipping of this product is only possible in accordance with the Chemicals Prohibition Ordinance to resellers, professional users and public research and educational institutions.Do you belong to this customer group? Then send us your request here. We will gladly prepare a delivery offer for you.For private users, delivery is only possible in our Hamburg store against proof of use.
BENAR matte wood oil
€39.90 *
BENAR MATT is a clear wood oil based on long-oil alkyd resin for achieving a matte finish as a final coat on other BENAR products such as BENAR GLOSS (Art.No.2091-003). The product forms a matte, breathable protective film with good water vapor permeability and is suitable for use on surfaces with little UV exposure, both indoors and outdoors. Application: Apply with a brush on clean, dry, grease-free surfaces. Technical DataArea of application: matte wood protection oil for indoor and outdoor useSubstrate: surfaces coated with BENARCoverage: 14-16 m²/l per coatThinning: noneApplication method: brush or airless (professional users)Drying times (at 23 °C): dust-dry after approx. 6 hrs, recoatable after 24 hrsSafety Note: Always use personal protective equipment during application. For more information on application, please refer to the Technical Data Sheet under 'Downloads'.The shipment of this product is only possible to resellers, professional users, and public research and educational institutions in accordance with the Chemicals Prohibition Ordinance.Are you part of this customer group? Then send us your inquiry here. We will be happy to provide you with a delivery offer.For private users, sale is only possible in our retail store in Hamburg upon proof of intended use.
BENAR UVR Wood Oil
From
€39.90 *
BENAR UVR is a high-gloss wood oil based on long oil alkyd resin with an additional red-brown pigmented UV filter for outdoor use. It was specially developed for tropical and European hardwoods such as teak, mahogany or oak and forms an elastic, breathable protective film with very good weather resistance. The high vapor permeability prevents moisture from being trapped under the varnish film and thus prevents rotting. The high elasticity  
BIO PIN natural boat oil
From
€19.90 *
Deeply penetrating natural oil, boiled from linseed oil, wood oil and hard spruce resin. Isoparaffinic serves as a solvent. BIO PIN boat oil dries to a high gloss and because of its composition is very long lasting, as well as water-, UV- and weather-resistant. It possesses a long-lasting elasticity, won't crack and no water can creep under. It is recommended as a base for BIO PIN.Coverage: approx. 12 m.sq./l.
EPIFANES Woodfinish Gloss
From
€24.89 *
Traditional oil varnish based on wood oil and alkyd resin for coating oily hardwoods such as teak and American softwoods. EPIFANES hardwood varnish oil serves as an alternative to pure oil systems and forms a grease and oil regulating clear varnish system in up to five coats.With a layer structure of less than five layers, the varnish oil still remains breathable. With more coats, the wood is completely sealed. Can be used for coating solid wood and plywood indoors and outdoors above the waterline, as well as for reworking existing one- and two-component lacquer systems.Application: Do not use the product below 8°C and avoid direct sunlight or strong wind. Apply the hardwood varnish oil with a brush. Do not apply wet on wet and avoid too thick layers to prevent drying problems, runs or craters. Intermediate sanding after the first coat after 24 hours by hand with a 280-320 grit paper, no intermediate sanding is necessary between subsequent coats as long as the drying times are observed. For oily woods, the manufacturer recommends a layer build-up of 5 coats, for other woods a layer build-up of 7 coats. 
EPIFANES Woodfinish Matte
€46.90 *
Clear varnish oil with a satin finish, specially suited for tropical woods, made from wood oil, phenol, and alkyd resin. EPIFANES Woodfinish Matte is suitable as a matte topcoat over a varnish build-up of EPIFANES Hardwood Varnish Oil Gloss or EPIFANES Clear Varnish. The varnish oil has very good resistance to solvents, alcohol, and household cleaners, as well as built-in UV protection.Application: The product can be applied with a high-quality brush to a previously sanded, clean surface. 1-2 coats are recommended, and no sanding between coats is necessary within 24-72 hours.Technical DataApplication area: Matte varnish oil finishSubstrate: clean, sanded clear coat systems such as EPIFANES Clear Varnish (Art.No. 2050-001) or Hardwood Varnish Oil Gloss (Art.No. 2051-001)Coverage: Approx. 13 m²/L at 35 µm dry film thicknessColor: clear, amberThinning: Brush: Epifanes Paint Thinner (Art.No. 2059-001), Spray: Epifanes 1-C Spray Thinner (Art.No. 2059-110)Application method: Brush, roller or spray gun (professional users)Drying times (at 20 °C): Dust dry after 3 hrs, sandable after 24 hrs, recoatable after 24 hrsFurther information on application can be found in the Technical Data Sheet under 'Downloads'.
LE TONKINOIS Clear Oil Varnish
From
€15.95 *
"TONKI" - the classic! Glossy, clear varnish oil for wood and metal. The formulation of LE TONKINOIS varnish oil is based on a special formula in which high-quality linseed oil and Chinese wood oil (tung oil) are cooked together. This creates a natural product without chemical additives. The varnish oil is suitable for indoor and outdoor use as well as for application under extreme weather conditions. It forms a resistant, elastic protective film with high UV resistance and highlights the natural grain of the wood.Application: LE TONKINOIS VARNISH is applied to untreated or cleanly sanded wood. Application is done with a brush or roller; for spray application, it can be diluted up to max. 10% with the appropriate LE TONKINOIS thinner. Only one thin coat should be applied per day. Stir well before use, do not apply below 12 °C.Technical DataArea of application: Wood and degreased metals indoors and outdoors, also under extreme weather conditionsSubstrate: Untreated wood, wood-based materials, limited use on corkCoverage: 20 m²/l Thinning: Max. 5–10% with LE TONKINOIS thinnerApplication method: Brush, flat brush, sprayingDrying times (at 20 °C): Dust dry after 6–8 h, reworkable after approx. 24 h, walkable after 3 days (with 2–3 coats)Further information on application can be found in the technical data sheet under 'Downloads'.
LE TONKINOIS Marine No.1 clear oil varnish
From
€35.90 *
"TONKI No.1" - the classic for sunny sailing areas. LE TONKINOIS MARINE NO.1 is a glossy, clear oil varnish specially developed for wooden surfaces in maritime environments. It is approved by the French Navy as a ship varnish and is suitable for both interior and exterior use. When applied properly, the product offers high weather and UV resistance, and is abrasion and impact resistant. Made from TONKINOIS varnish oil, but slightly thinner and faster-drying. The formulation is free from chemical additives, considered child-safe (according to DIN EN 71-3), and enables long-lasting surface protection with multiple applications.ApplicationMarine No. 1 is applied to untreated or appropriately pretreated wood. Application is done using a brush, flat brush, or by spraying. The coats are applied thinly, with only one layer per day. For exterior areas, six to ten coats are recommended; for interior areas, half is sufficient. A primer with Bio Impression is recommended for untreated or highly absorbent wood. The application temperature should be at least 12 °C.Technical DataApplication area: Wooden surfaces indoors and outdoors, seawater and UV resistantSubstrate: Untreated wood, wood-based materials, conditionally corkPrimer: Bio ImpressionCoverage: 20 m²/l per coatThinning: Use undiluted; when spraying max. 10% Le Tonkinois thinnerApplication method: Brushing, rolling, sprayingDrying times (at 20 °C): Dust-dry after 5–8 h, recoatable after at least 24 hFurther information on application can be found in the Technical Data Sheet under 'Downloads'.
LE TONKINOIS Yacht Oil Stain
From
€12.90 *
LE TONKINOIS Yacht Oil Stain is a plant oil-based, intensely colored wood pre-treatment for hardwood surfaces indoors and outdoors. The stain penetrates deeply into the wood and creates a uniform coloration with a pleasant feel. It is resistant to dirt and water-repellent, and the pigmentation increases UV protection. In boatbuilding it is suitable for matching the color of wooden surfaces on decks, superstructures and other heavily used surfaces. For adequate protection, a subsequent protective coating with LE TONKINOIS Vernis or Marine No.1 is recommended.Application: The surface must be dust- and grease-free and clean; the wood moisture should not exceed 15%. The stain is applied undiluted with a brush or roller to untreated wood. After a short exposure time, the excess is evenly distributed and removed with a lint-free cloth. It is recommended to create a test area beforehand. The processing temperature should be at least 12 °C. Walkability is achieved after three days with 2–3 coats.Technical DataField of application: Indoor and outdoor, e.g., boat decks, superstructures, wooden floorsSubstrate: Untreated wood, wood-based materialsCoverage: 35–50 ml/m² (depending on type of wood)Application method: Brushing with brush or rollerDrying times (at 20 °C): Dust-dry after 6–8 h, re-coatable after 12 h, walkable after 3 daysFor more information on processing, please refer to the technical data sheet under 'Downloads'.
OWATROL DECK SEALER Wood Protection
From
€32.90 *
Transparent protective and maintenance oil with UV protection for all exterior wood, particularly suitable for teak decks. OWATROL DECK SEALER is an air-drying natural oil with properties similar to OWATROL TEXTROL Transparent. Due to its excellent penetration properties, it penetrates deep into the wood and thus protects against weathering from the inside out. It is non-film-forming and open to diffusion, so that moisture exchange is guaranteed. The transparent oil does not change the original shade of the wood, but intensifies the shade as if the surface were wet.The product is leached out by weathering over time, so regular reworking in combination with DECK CLEANER is recommended, depending on the weather conditions.Technical dataArea of application: Exterior wood, e.g. decks, furniture, masts, walkwaysSurface: clean, dry, grease-free, sand if necessaryApplication: cloth, brush, fur roller, sprayerCoverage: approx. 5 m²/l (initial treatment), approx. 10 m²/l (maintenance)Dilution: noneApplication temperature: 5 °C to max. 35 °C (not in direct sunlight)Drying time (20 °C): 24-48 hoursFurther information on processing can be found in the technical data sheet under "Downloads".
OWATROL INTERIOEL Interior Wood Finish
From
€39.90 *
Protective and maintenance oil with high penetration capacity for all interior wood. OWATROL INTERIÖL is colourless and produces a silky matt surface that emphasizes the natural grain of the wood. A glossy finish can be achieved by applying a further coat 24 hours after the wood is saturated.Stabilizes raw, untreated wood from the inside out and reduces swelling and shrinkage due to saturation. Protects physically (moisture cannot penetrate) and thus prevents the infestation of mold and fungal infestation, completely without chemical fungal protection or pesticides. Application: Apply the oil wet-on-wet without intermediate drying (interval approx. 30 to 60 minutes) until the wood is saturated. Do not allow to dry between coats. According to the manufacturer, 4-6 coats are recommended when treating wooden floors. One hour after the last coat, the surface should be wiped with a clean, lint-free cloth to distribute and absorb excess material. Otherwise the surface may remain sticky. If this interval is exceeded, excess product can be removed mechanically by sanding or with a suitable paint remover (OWATROL DILUNETT, Art. No. 2511-001). Very absorbent woods should be treated again after 12 hours at the earliest. To achieve a perfect finish, the surface can be sanded with 120 grit sandpaper and INTERIÖL as a sanding liquid.Technical DataApplication area: Interior wood, e.g. furniture, floors, panels, kitchen countertopsSubstrate: bare, clean, dry, grease-free, soundApplication: soft flat brush, mohair roller, fine spray deviceCoverage: approx. 8-12 m²/l Thinner: noneApplication temperature: +8 °C to max. +35 °CDrying (20 °C): dust dry after 4–5 hrs, fully dry after 12–72 hrs.Further information on application can be found in the Technical Data Sheet under "Downloads".
TEXTROL-RUSTIKAL wood protection OWATROL
From
€32.90 *
Transparent protective and maintenance oil with UV protection for all exterior wood.OWATROL TEXTROL RUSTIC is an air-drying wood oil that penetrates deep into the wood and protects it from the inside out. It does not form a layer on the surface of the wood and therefore cannot flake off. Provides long-lasting protection against moisture, weathering and UV radiation and can be used on both horizontal and vertical surfaces. The oak color pigmentation provides additional protection against UV rays and graying.Application: Waxed or varnished wood should be treated with OWATROL NET-TROL (2508-001) before application. Also wood containing tannic acid such as oak should be cleaned beforehand and treated with NET-TROL. Apply two coats wet-on-wet on the bare wood at intervals of 15-30 minutes. A third coat is recommended for particularly dry or porous wood surfaces. Wait 30-60 minutes after applying the last coat and then wipe off any excess material with a clean cotton cloth to prevent a film from forming. Otherwise the surface may remain sticky or stained. Technical DataApplication area: Exterior wood, e.g. decking, cladding, furniture, fencesSubstrate: bare, clean, grease-free, dryApplication: brush, rollerCoverage: approx. 10–12 m²/lThinner: noneApplication temperature: min. +5 °C to max. +25 °C (avoid direct sunlight)Drying (20 °C): 24–48 hrsFurther information on application can be found in the Technical Data Sheet under "Downloads".
