Go to homepage
€0.00*
Jobs
Catalogue
Quick order
2577-910 HEMPEL HEMPASPEED TF Antifouling 750ml 2577-910 HEMPEL HEMPASPEED TF Antifouling 750ml
2577*36 HEMPEL HEMPASPEED TF Dünnfilm-Unterwasser-Beschichtung - Bild 2 2577*36 HEMPEL HEMPASPEED TF Dünnfilm-Unterwasser-Beschichtung - Bild 2
2577-910 HEMPEL HEMPASPEED TF Antifouling 750ml
2577*36 HEMPEL HEMPASPEED TF Dünnfilm-Unterwasser-Beschichtung - Bild 2

HEMPEL'S Hempaspeed TF is a hard, biocide-free thin-layer coating for all sports boats with GRP, steel or aluminum hulls, including regatta and trailer boats. Thanks to the special hydrogel technology, it forms an ultra-smooth surface that minimizes fouling and also reduces friction. Suitable for fresh, salt and brackish water as well as inland areas. Particularly recommended in areas where the use of biocides is prohibited or restricted (also in the Netherlands). 

Application on existing antifouling layer: It is possible to switch from a conventional antifouling to Hempaspeed TF. The old coating (if still intact) does not need to be removed. A coat of HEMPEL Conversion Primer should be applied as an adhesion primer, followed by two coats of Hempaspeed TF.

Application as a new coating: When applying a new coating, the substrate must first be sealed with HEMPEL Light Primer before applying HEMPEL Conversion Primer and two coats of Hempaspeed TF.

Note: The effectiveness of biocide-free underwater coatings depends on the area of operation and the boat's sailing characteristics. Regular inspection of the hull during the season is recommended. Any fouling that occurs can be minimized by gentle cleaning with a sponge or soft brush.

Technical Data

  • Area of use: For fresh and saltwater with medium fouling; mechanical cleaning may be necessary in high fouling areas
  • Boat type: For sport and racing boats, suitable for high-speed vessels
  • Substrate: GRP, steel, aluminium; suitable over existing antifouling in good condition
  • Primer: HEMPEL Conversion Primer
  • Coverage: 11 m²/l
  • Thinner: HEMPEL'S Thinner 808
  • Application method: Brush, roller, airless spray (professional use)
  • Drying times: Touch dry after 30 min at 10 °C; recoatable after 8 hrs at 10 °C
  • Refloating time (time between painting and launching): 24 hrs to 3 months

Further information on processing can be found in the technical data sheet under “Downloads”.

more information

from €42.90*

Content: 0.7519 (€57.06* / 1 Liter)

€42.90*

Content: 0.7519 Liter (€57.06* / 1 Liter)

Prices incl. VAT plus shipping costs

colour
contents
Geb
View article in the TOPLICHT catalogue

Description

HEMPEL'S Hempaspeed TF is a hard, biocide-free thin-layer coating for all sports boats with GRP, steel or aluminum hulls, including regatta and trailer boats. Thanks to the special hydrogel technology, it forms an ultra-smooth surface that minimizes fouling and also reduces friction. Suitable for fresh, salt and brackish water as well as inland areas. Particularly recommended in areas where the use of biocides is prohibited or restricted (also in the Netherlands). 

Application on existing antifouling layer: It is possible to switch from a conventional antifouling to Hempaspeed TF. The old coating (if still intact) does not need to be removed. A coat of HEMPEL Conversion Primer should be applied as an adhesion primer, followed by two coats of Hempaspeed TF.

Application as a new coating: When applying a new coating, the substrate must first be sealed with HEMPEL Light Primer before applying HEMPEL Conversion Primer and two coats of Hempaspeed TF.

Note: The effectiveness of biocide-free underwater coatings depends on the area of operation and the boat's sailing characteristics. Regular inspection of the hull during the season is recommended. Any fouling that occurs can be minimized by gentle cleaning with a sponge or soft brush.

Technical Data

  • Area of use: For fresh and saltwater with medium fouling; mechanical cleaning may be necessary in high fouling areas
  • Boat type: For sport and racing boats, suitable for high-speed vessels
  • Substrate: GRP, steel, aluminium; suitable over existing antifouling in good condition
  • Primer: HEMPEL Conversion Primer
  • Coverage: 11 m²/l
  • Thinner: HEMPEL'S Thinner 808
  • Application method: Brush, roller, airless spray (professional use)
  • Drying times: Touch dry after 30 min at 10 °C; recoatable after 8 hrs at 10 °C
  • Refloating time (time between painting and launching): 24 hrs to 3 months

Further information on processing can be found in the technical data sheet under “Downloads”.

Downloads

Questions about the product?
Questions about the product?
Talk to craftsmen, boat builders and sailors. We understand your questions and provide the right answers.
Contact experts
Legal information about the product
CLP Regulation
Symbols ghs02 ghs07 ghs09
Signalword Attention!
H phrases H226, H335, H336, H411
P phrases P304, P312, P405, P403+P233, P501, P102, P101, P210, P271, P273, P260, P391, EUH208
2577-918 HEMPEL CONVERSION Primer
HEMPEL CONVERSION Primer
HEMPEL CONVERSION Primer is a two-component epoxy resin-based adhesion primer. It was developed to facilitate the change from conventional antifoulings to the biocide-free thin-film antifouling HEMPASPEED TF from HEMPEL. The primer can be applied to existing antifoulings (including International VC-17m) as well as to one- and two-component primers, provided the surface is intact and stable. Caution: The primer does NOT provide corrosion protection, but merely acts as an adhesion promoter. Prime uncoated surfaces with a corrosion protection primer beforehand. Two-component primers based on epoxy resin (e.g. HEMPEL Light Primer) are recommended. Technical DataSubstrate: Existing antifouling in good condition (not suitable for bare surfaces)Surface preparation:Wet sand old antifouling with water and waterproof paperRinse with fresh water, clean and allow to drySurface must be clean, dry and free of greaseTopcoat: HEMPEL's Silic One Tiecoat, Hempaspeed TFCoverage: approx. 15 m²/l at 25 µm dry film thicknessThinner: Do not thinApplication method: Brush, roller Mixing ratio: 3:1 (Base:Hardener by volume)Pot life: 8 hrs at 20 °CDrying times at 20 °C: Dust dry after 1¼ hrs; recoatable after 2 hrs (Silic One Tiecoat), 30 min (Hempaspeed TF); fully cured after 7 daysFurther information on processing can be found in the technical data sheet under “Downloads”.

From €48.90 *
Details
2577*13 HEMPEL LIGHT PRIMER
HEMPEL LIGHT PRIMER
HEMPEL LIGHT PRIMER is a high-quality two-component primer based on epoxy resin for underwater and above-water applications. It serves as a good barrier against penetrating water vapor on rigid substrates, for osmosis prevention and repair on GRP and as corrosion protection on metals. It can also be used on plywood and hardwood. Suitable for interior and exterior use above and below the waterline, as well as for coating keels and rudders.Within the specified recoating intervals, LIGHT PRIMER can also be recoated directly with a subsequent product without intermediate sanding. The surface should be almost dry, but still slightly tacky. For a subsequent coat of antifouling, a coat of HEMPEL UNDERWATER PRIMER (Art. No. 2577-053) is recommended as an adhesion primer.Technical dataSubstrates: GRP, plywood, steel, aluminum, existing coatingsPre-treatment:GRP: sand, clean, remove dustPlywood: seal with a suitable sealerSteel: high-pressure cleaning, sandblasting or mechanical rust removal, dust removalOld coatings: sand, clean, dryPorous surfaces: prime first coat of Light Primer with 20% thinnerSubsequent coat: standard 1K and 2K products (see data sheet)Coverage: 8.2 m²/l at 60 µm dry film thicknessThinner: HEMPEL'S THINNER 845 (Art. No. 2577-022)Application method: Brush, roller, airless spraying (professional users)Drying times at 10 °C: Hand dry after 6 hours; recoatable after 9 hours.Further information on application can be found in the technical data sheet under "Downloads".

From €24.89 *
Details
More Products from Category Thinfilm antifouling
2570*01 SEALINE Dünnschicht-Antifouling SILVER RACING
SEA-LINE THIN FILM SILVER RACING Antifouling
Very smooth and extremely fast-drying thin-layer antifouling with PTFE anti-adhesion technology and copper oxides as biocidal active ingredients.For medium fouling conditions in salt water, brackish water, fresh water and lakes. Can be applied to all epoxy underwater primers and is compatible with PTFE thin-film antifoulings such as VC 17m and Hempel Waterglide.Before applying SEA-LINE THIN FILM to an already painted surface, please refer to the compatibility table. Do not use on aluminum or zinc surfaces. Technical DataArea of application: Waters with medium foulingBoat type: motor and sailing boats up to 40 knotsSubstrate: all materials except aluminumCoverage: approx. 11-12 m²/lDilution: Not recommendedApplication method: Brush, roller, spraying (professional use only)Drying times at 15°C: Dust-dry: approx. 30 minutes, recoating interval: min. 10 hoursRefloating (time between painting and launching) at 15°C: 3 hours to 6 months Further application information can be found in the technical data sheet under “Downloads”.

From €49.90 *
Details
Last seen products