SIGMA ECOFLEET 290S Self-Polishing Antifouling

EPIFANES COPPER CRUISE is a highly efficient antifouling containing copper and biocides with a self-polishing effect and excellent long-term fouling protection in fresh, brackish and salt water. Copper release technology combines the advantages of hard antifouling and self-polishing antifouling with significantly improved fouling protection. Compared to conventional copper-containing antifoulings, the active ingredients are optimized and released in much smaller quantities, which benefits the environment.Can be easily applied to most commercially available underwater primers, as well as hard and self-polishing antifoulings. Suitable for all sailing and motor boats with a maximum speed of 30 knots and for all boat building materials except aluminum. Not suitable for long-term moorings that are not moved or only moved a little throughout the season. This antifouling has a Dutch approval (approval no. 14301). Technical dataArea of application: Waters with medium to heavy foulingBoat type: motor and sailing boats up to 30 knotsSubstrate: all materials except aluminumCoverage: approx. 10 m²/lDilution: Not recommended, max. 2-3 % with EPIFANES Thinner D-100Application method: Brush, rollerDrying times at 20°C: Dust-dry: approx. 30 min., recoatable: after approx. 8 hoursService life (time between painting and wetting) at 20°C: min. 24 hours to 1 monthFor information on processing, please refer to the technical data sheet under "Downloads".&nbsp

EPIFANES FOUL-AWAY is a self-polishing, biocide-free underwater ship paint. Suitable for freshwater, brackish water and occasional saltwater areas. Suitable for all boat building materials. Adheres to all hard antifoulings and self-polishing antifoulings. Three coats are recommended for the first application.Note: The effectiveness of biocide-free underwater coatings depends on the area of operation and the boat's sailing characteristics. Regular inspection of the hull during the season is recommended. Any fouling that occurs can be minimized by gentle cleaning with a sponge or soft brush.Technical DataArea of use: Freshwater areas and temporary exposure in brackish and saltwaterBoat type: Sailing and motorboats Substrate(with suitable primer): Wood, steel, GRP, aluminium, existing hard or self-polishing antifoulingsPrimer: EPIFANES Interimcoat or EPIFANES Underwater PrimerCoverage: 10 m²/l at 50 µm dry film thicknessThinner: EPIFANES Thinner D-100Application method: Brush, roller, sprayDrying times: Dust dry after 1 hr at 20 °C; recoatable after 6 hrsRefloating time (time between painting and launching): 24 hrs to 6 monthsFurther information on processing can be found in the technical data sheet under "Downloads".

High-performance, self-polishing antifouling. Excellent fouling protection thanks to HEMPEL's patented binder technology.Especially for aluminum boats, but can also be used for boats made of GRP, wood, steel and drives. Can be applied with a roller or brush. Technical dataArea of application: Waters with medium to heavy foulingBoat type: Motor and sailing boatsSubstrate (with suitable primer): all materials, including aluminumSuitable primer: HEMPEL'S Underwater Primer, HEMPEL'S Light PrimerCoverage: approx. 13 m²/lThinner: HEMPEL THINNER 808Application method: Brush, rollerDrying times at 10°C: Surface dry: 8 hours, recoatable: after approx. 7 hoursRefloating time (time between painting and launching) at 20°C: min. 24 hours to 9 months For information on application, please refer to the technical data sheet under “Downloads”. 

Robust and reliable, self-eroding antifouling with copper compounds as the active ingredient. No sanding required before subsequent coating. Suitable for all boat building materials except aluminum. Economical protection for the entire season in salt, brackish and fresh water areas with moderate temperatures.This antifouling has a Dutch approval (approval no. 15010).Technical dataArea of application: Waters with medium to heavy foulingBoat type: Sailing and motor boats with normal speedSubstrate: GRP, wood, plywood, steel (not suitable for aluminum)Coverage: approx. 13 m²/L (theoretically at 40 µm dry film thickness)Thinner: Hempel's Thinner 808 (max. 5 % for brush/roller application)Application method: Brush, rollerDrying times (at 10 °C): Hand dry after approx. 30 min., recoatable after approx. 8 hrs.Reflotating time (time between painting and launching): 24 hours - 1 monthFurther information on application can be found in the technical data sheet under “Downloads”.

HEMPEL Ecopower Cruise is a biocide-free, self-polishing underwater hull coating for all materials, including aluminum. The innovative binder technology allows for controlled self-renewal of the surface, and seasonal fouling can be easily removed by mechanical cleaning. Ideal for sport and recreational boats in ecologically sensitive waters, this coating provides reliable seasonal protection with easy application.Note: The effectiveness of biocide-free underwater coatings depends on the cruising area and the boat’s performance. Regular hull inspections during the season are recommended. Emerging fouling can be minimized by gentle cleaning with a sponge or soft brush.Technical DataApplication Area: For areas with light fouling pressureBoat Type: For medium-speed motor and sailing boatsSubstrate: GRP, wood, plywood, steel (with appropriate primer), self-polishing antifoulings, traditional antifouling or hard old coatings in good conditionPrimer: HEMPEL Light Primer, HEMPEL Underwater PrimerCoverage: 14 m²/lThinner: Hempel's Thinner 808Application Method: Brush, rollerDrying Times: Touch dry after 30 min at 10 °C; recoatable after 8 hrs at 10 °CLaunch Time (time between painting and launching): 24 hrs to 9 monthsFurther information on application can be found in the technical data sheet under "Downloads".

HEMPEL'S ECOPOWER PROP Spray is a biocide-free spray paint for coating propellers, Z-drives and stern drives. Protects against fouling and facilitates cleaning. An advanced binder technology controls the self-renewing effect over the entire season.For use on uncoated surfaces, priming with HEMPEL'S Prop Primer is recommended.For existing, old or traditional antifouling, remove loose material and fouling beforehand. On surfaces with existing, old hard matrix or unknown antifouling, the surface should also be wet-sanded (180 grit). Then clean and dry the surface. If the condition of the previous antifouling layer is poor, seal with a layer of primer (e.g. HEMPELS Prop Primer).Note: The effectiveness of biocide-free underwater coatings depends on the area of operation and the boat's sailing characteristics. Regular inspection of the hull during the season is recommended. Any fouling that occurs can be minimized by gentle cleaning with a sponge or soft brush.Technical dataArea of application: Waters with light to medium fouling conditionsBoat type: motor and sailing boats Surface: all materials, including aluminumSuitable primer: HEMPEL'S Underwater Primer or HEMPEL'S Prop PrimerCoverage: approx. 11 m²/lDilution: noneApplication method: SprayingDrying times at 10°C: Hand dry: 30 minutes, recoatable: n.a.Refloation time (time between painting and launching) at 10°C: min. 24 hours to 1 monthFurther application information can be found in the technical data sheet under “Downloads”.

HEMPEL'S Mill NCT self-polishing premium antifouling has a highly effective fouling protection thanks to copper compounds and organic active ingredients.NCT technology (NewCopperTechnology) makes it possible to use the copper compounds in an even more controlled and continuous manner, making them even more economical and effective.The self-sanding effect of the antifouling always ensures a smooth, low-friction and bioactive surface and it does not need to be sanded before a subsequent coat.Suitable for all boat building materials (except aluminum) and for use in all waters.Technical DataArea of application: Waters with medium to heavy foulingBoat type: motor and sailing boatsSubstrate: all materials except aluminumCoverage: approx. 14 m²/lDilution: HEMPEL THINNER 808Application method: Brush, rollerDrying times at 10°C: Surface dry: 4 hours, recoatable: after approx. 8 hoursRefloating time (time between painting and launching) at 10°C: min. 24 hours to 9 months Further information on application can be found in the technical data sheet under “Downloads”.

Current delivery information: Unfortunately, this product is no longer available. However, you can coat LEFANT NAUTICA HARD ECO with all conventional self-polishing antifoulings from our range (biocide-containing or biocide-free). We recommend lightly roughening the surface with wet sandpaper before changing the system. NAUTICA HARD ECO is a biocide-free underwater hull coating from the Swedish company LEFANT, which is suitable for sailing and motor boats of all speed ranges. It forms a hard, polishing surface that protects the boat from fouling and is easy to clean.NAUTICA HARD ECO is suitable for use on aluminium hulls and is compatible with most self-polishing and hard antifouling. Two coats are sufficient for seasonal protection, additional coats may be required in areas of higher friction and wear such as the rudder, stern and waterline.Note: The effectiveness of biocide-free underwater coatings depends on the area of operation and the boat's sailing characteristics. Regular inspection of the hull during the season is recommended. Any fouling that occurs can be minimized by gentle cleaning with a sponge or soft brush.Technical DataArea of use: Suitable for waters with low to medium fouling pressureBoat type: For sailing and motorboats of all speed rangesSubstrate: Suitable for GRP, aluminium and most hard or semi-soft solvent-based antifoulingsPrimer: LEFANT EPOXY PRIMERCoverage: 13 m²/lThinner: NoneApplication method: Brush, rollerDrying times: recoatable after 12 hrs at 10 °CRefloating time (time between painting and launching): 24 hrs to 2 months at 20 °CFurther application information can be found in the technical data sheet under "Downloads".

SEAJET 021 EKO is a biocide-free underwater coating that forms a hydrolysis-based, erodible layer that is constantly renewed, making it difficult for dirt and fouling to adhere. It is applied like a conventional antifouling, two coats last a season. SEAJET 021 EKO can be painted on primed wood, GRP, steel and aluminum. Suitable for boats with maximum speeds of up to 40 knots.Application: For a new coating of the underwater hull, 2 coats of SEAJET 117 Epoxy Primer are suitable for priming, for wooden hulls SEAJET 015 Underwater Primer. Then apply 2 coats of SEAJET 021 EKO. When applying to existing antifouling, compatibility should be checked beforehand, e.g. using the SEAJET compatibility table (can be found under "Downloads"). Clean underwater coatings in good condition, apply 1 coat of SEAJET 015 Underwater Primer, then apply 2 coats of SEAJET 021 EKO.Note: The effectiveness of biocide-free underwater coatings depends on the area of operation and the boat's sailing characteristics. Regular inspection of the hull during the season is recommended. Any fouling that occurs can be minimized by gentle cleaning with a sponge or soft brush.Technical dataArea of application: Waters with light foulingBoat type: motor and sailing boats up to 40 knotsSubstrate: all materials (with suitable primer)Coverage: approx. 10 m²/lDilution: SEAJET THINNER AApplication method: Brush, roller, spraying (professional use only)Drying times at 10°C: Dust-dry: approx. 2 hours, recoatable: after approx. 7 hours.Time between painting and launching at 10°C: min. 12 hours.For information on processing, please refer to the technical data sheet under "Downloads".

Very effective, self-polishing antifouling, even in difficult fouling conditions.Suitable for all boat building materials except aluminum. Adheres to most hard and self-polishing antifoulings (not to those containing Teflon). Sanding before the next coat is not necessary. 2-3 coats last for 2 seasons.Technical dataArea of application: Waters with medium foulingBoat type: motor and sailing boats up to 40 knotsSubstrate: all materials except aluminumCoverage: approx. 8.8 m²/lDilution: SEAJET THINNER AApplication method: Brush, roller, spraying (professional use only)Drying times at 10°C: Dust-dry: approx. 2 hours, recoatable: after approx. 8 hoursTtime between painting and launching at 10°C: min. 18 hours to 6 monthsFor information on processing, please refer to the technical data sheet under "Downloads".

SEAJET 034 EMPEROR A SPRAY is a self-polishing antifouling in spray form. It is suitable for underwater coating of smaller areas, touch-ups (spot repair), saildrives, outboard motors, as well as for hard-to-reach areas. The formulation contains no metallic copper and, with the appropriate primer, is also suitable for aluminum surfaces. Forms a smooth, self-polishing surface and provides effective protection against algae and shellfish growth. Slight color changes may occur upon contact with water.Application: The surface must be clean, dry, free of grease, and sound. Existing antifouling in good condition can – after checking compatibility – be directly recoated. Unknown or incompatible old coatings must be isolated with SEAJET 015 UNDERWATER PRIMER (Art.No. 2559-015). If in poor condition, the old antifouling must be completely removed, and the substrate cleaned and degreased.  New build-up: Pre-coat GRP, steel, and aluminum with SEAJET 117 MULTIPURPOSE EPOXY PRIMER (Art.No. 2559-117), wood with SEAJET 015 UNDERWATER PRIMER (Art.No. 2559-015). Shake the spray can vigorously for at least 2 minutes before use. Application at 5–35 °C, substrate temperature 7–35 °C, max. 85 % relative humidity. Always ensure good ventilation during application, do not inhale vapors. Product is flammable.Technical DataArea of application: Waters with medium to heavy foulingBoat type: Motorboats and sailboats up to 40knSubstrate: GRP, wood, steel, aluminum (with suitable primer)Primer: SEAJET 015 UNDERWATER PRIMER (Art.No. 2559-015), SEAJET 117 MULTIPURPOSE EPOXY PRIMER (Art.No. 2559-117)Coverage: approx. 10,0 m²/l (theoretical); corresponds to approx. 0,75–1,0 m² per 400 ml spray can depending on film thickness and substrateApplication method: Spray canDrying times (at 20 °C): dust-dry after approx. 1 hr., dry after approx. 5 hrs.; recoatable after min. 5 hrs.Service life (time between application and launching): 24 hrs. up to max. 6 monthsFurther information on application can be found in the Technical Data Sheet under 'Downloads'.

SEAJET Emperor 034 A is a slowly eroding (=self-polishing) antifouling that contains no copper and is therefore also suitable for aluminum hulls. Its effective formulation makes it suitable for use in tropical saltwater areas with high fouling pressure.Technical dataArea of application: Waters with heavy foulingBoat type: motor and sailing boats up to 40 knotsSubstrate: all materials, including aluminum (with suitable primer)Coverage: approx. 10 m²/lDilution: SEAJET THINNER AApplication method: Brush, roller, sprayingDrying times: Dust-dry: approx. 3 hours, recoatable: after approx. 12 hoursTime between painting and wetting: min. 24 hours to 6 monthsFor further application information, please refer to the technical data sheet under "Downloads".

SEAJET PROFESSIONAL 032 is an economical, self-polishing antifouling with copper compounds as the active ingredient. This antifouling was developed for small commercial and work boats and traditional sailing boats in salt, brackish and fresh water areas.Suitable for all boat building materials except aluminum. No sanding required before a subsequent coat.Current delivery information: The container size 3.5l has been discontinued, the product is still available in 5l containers. Technical DataArea of application: Waters with medium foulingBoat type: motor and sailing boats up to 40 knotsSurface: all materials except aluminumCoverage: approx. 8.7 m²/lDilution: SEAJET THINNER AApplication method: Brush, roller, spraying (professional use only)Drying times at 10°C: Dust-dry: approx. 2 hours, recoatable: after approx. 7 hoursTime between painting and wetting at 10°C: min. 16 hours to 6 monthsFor information on processing, please refer to the technical data sheet under "Downloads".

SEAJET 031 SAMURAI is a slow-eroding antifouling with good all-round performance for waters with medium fouling conditions. It is suitable for all boatbuilding materials except aluminum and adheres to most hard and self-polishing antifoulings (not to Teflon and tin-containing antifoulings).Technical dataArea of application: Waters with medium foulingBoat type: motor and sailing boats up to 40 knotsSubstrate: all materials except aluminum (with suitable primer)Coverage: approx. 9 m²/lDilution: SEAJET THINNER AApplication method: Brush, roller, sprayingDrying times: Dust-dry: approx. 2 hours, recoatable: after approx. 6 hoursService life (time between painting and wetting): min. 24 hours to 6 monthsInformation on Application can be found in the technical data sheet under "Downloads".

Self-polishing long-term antifouling from commercial shipping, suitable for use in offshore waters with high fouling pressure.Ecofleet 290 S contains bioactive organic biocides and copper compounds, which are released in a controlled and effective manner through the continuous polishing rate. It therefore offers effective protection against fouling for 36 - 60 months (depending on sailing style and routes). Complies with the IMO Antifouling Systems Convention.Can be applied to most hard and self-polishing antifoulings (not to PTFE-containing antifoulings).Technical dataArea of application: Waters with heavy fouling, offshoreType of boat: Commercial vessels and slow-moving vessels, multihullsSubstrate (primed): all materials except aluminumCoverage (theoretical): 7,3 m²/l at 75 µm (spray application), 11 m²/l at 50 µm (roller application)Dilution: SIGMA 21-06 (max. 3% recommended)Application method: Spray gun (new coating), brush, roller (touch-ups)Drying times at 10°C: Recoatable: after approx. 10 hours.Standing time (time between painting and wetting) at 10°C: at least 12 hours.For information on application, please refer to the technical data sheet under "Downloads".

Reliable, self-polishing antifouling with copper compounds and organic, bioactive substances for northern European coastal and inland waters. Thanks to the self-eroding surface, the bioactive substances can always develop their optimum effect over the entire service life of the coating and it does not need to be sanded before a new coat is applied. Cannot be applied to Teflon-based coatings.YACHTCARE ANTIFOULING SP is compatible with most antifouling systems and is suitable for all boat types and boat building materials except aluminum. Technical dataArea of application: Waters with medium to heavy foulingBoat type: Motor and sailing boats with medium speedSubstrate (with appropriate primer): all materials except aluminum, check existing coatings for compatibility before applicationCoverage: approx. 12.7 m²/lDilution: YACHTCARE ANTIFOULING THINNERApplication method: Brush, roller, spraying (professional use only)Drying times at 20°C: Recoatable: after approx. 6 hoursFurther information on processing can be found in the technical data sheet under “Downloads”. 

YACHTCARE SAFEGUARD SP is a self-polishing, biocide-free underwater coating for cruising areas with light to moderate fouling. It is suitable for sailing and motorboats made of GRP, steel, wood or aluminum. The specially developed LUBRICATOR FLUID by YACHTCARE, a special additive, makes it harder for fouling to adhere to the surface and makes cleaning easier after hauling out the boat. SAFEGUARD SP can be applied to most sanded hard and self-polishing antifoulings without the need for a bonding primer. Not suitable for application on thin-film antifoulings.Note: The effectiveness of biocide-free underwater coatings depends on the cruising area and the boat’s performance. Regular hull inspections during the season are recommended. Emerging fouling can be minimized by gentle cleaning with a sponge or soft brush.Technical Data•    Application Area: Waters with light to moderate fouling•    Boat Type: Sailing and motorboats up to 25kn•    Substrate: all materials •    Coverage: approx. 11 m²/l•    Thinner: none•    Application Method: Brush, mohair or foam roller•    Drying Times at 20°C: Recoatable: after approx. 6 hours •    Launch Time (time between painting and launching) at 10°C: min. 24 hrs to 6 months For application information, please refer to the technical data sheet under “Downloads”.