Burner coil for REFLEKS oil heater 62

Adapter for SALAMANDER SE to REFLEKS exhaust pipe

Adapter suitable for oven SALAMANDER SE, which enables the use of REFLEKS stainless steel pipes of size 114 mm.

€49.00 *

Details

Cap for through-hull REFLEX

Closing cap, stainless steel. Suitable for all REFLEKS flue pipes.

From €48.00 *

Details

Deck through hull REFLEKS components

Components for mounting a through-deck fitting that matches your deck inclination perfectly.Pipe, a round deck plate and flange to weld locally.Made of stainless steel.Fits the REFLEKS flue pipes.

From €98.00 *

Details

Rotary ventilator ASPIROMATIC stainless steel

Rotating stainless steel vent that can also be used as a gas vent for all opening types, protected against backdrafts and supports the correct draft of the chimney.The (folding) extraction fan runs on ball bearings and is propelled by the wind.The flange is made of a light DURAL-INOX alloy. Available is also a version 240 C with a square ground plate (330 x 330mm) for profiles of 200 x 200mm up to 250 x 250mm. The enclosed attachment bolts allow mounting on pipes of varying diameters.Output data based on 3 beaufort wind velocity (10 kn).

From €298.00 *

Details

REFLEKS-adapter for ASPIROMATIC ventilator

Fits the REFLEKS 90 mm flue pipe system, in order to attach the small ASPIROMATIC ventilator (Art-Nr. 1836-160). Stainless steel, 1 mm wall thickness. Diameter 95 / 150 mm, height 95 mm.

€107.00 *

Details

Flue pipes REFLEKS

This flue pipes matches the REFLEKS heating system and other gas or coal stoves with matching exhaust outlets.Made of acid-proof stainless steel (wall depth 0.6 mm).Plugs together: slightly conical with pressed sleeve on one side.

From €29.90 *

Details

Flue pipe elbow 45° REFLEKS

This flue pipes matches the REFLEKS heating system and other gas or coal stoves with matching exhaust outlets.Made of acid-proof stainless steel (wall depth 0.6 mm).Plugs together: slightly conical with pressed sleeve on one side.

From €56.91 *

Details

Flue pipe elbow 90° REFLEKS

This flue pipes matches the REFLEKS heating system and other gas or coal stoves with matching exhaust outlets.Made of acid-proof stainless steel (wall depth 0.6 mm).Plugs together: slightly conical with pressed sleeve on one side.

From €61.00 *

Details

Flue pipe elbow 90° REFLEKS with cleanout door

This flue pipes matches the REFLEKS heating system and other gas or coal stoves with matching exhaust outlets.Made of acid-proof stainless steel (wall depth 0.6 mm).Plugs together: slightly conical with pressed sleeve on one side.

From €69.90 *

Details

Flue gas damper REFLEKS

Pipe socket with draft flap for draw regulation and performance improvement of REFLEKS stoves.The exhaust ventilation is installed directly over the stove and when used automatically guides air into the exhaust guide pipe.Recommended for long or problematic exhaust leads.Length 330 mm.

From €132.99 *

Details

Flue guard REFLEKS

Guard for flue pipes that are installed in close quaters.Avaiable in stainless steel, brass or copper plate.The risk of contact burns is minimized, but the warmth of the pipe can still be enjoyed.Matches REFLEKS flue pipes of 70 mm or 90 mm.The flue guard is attached to the flue pipe and fixed with two stainless steel brackets, which are included in the package.Distance from flue pipe, 15 mm.

From €109.00 *

Details

Wall shade inox

Small reflector plate for heat protection behind flue pipes.Plate stainless steel.Measurements:50cm high, 15cm wide.Available as flat or recessed version.The flat plate must be mounted with spacers or insulation behind, the recessed plate can be mounted directly on the wall.

From €35.90 *

Details

Wall mount for REFLEKS oil heaters 66 M/M-C

Wall bracket for REFLEKS ovens in the 66M series without hot water coil.This sturdy wall bracket is used to securely mount REFLEKS ovens from the 66M series on board. It enables self-supporting installation on a bulkhead and provides the necessary clearance to adjacent components. Wall mounting leaves the floor area free and easier to clean. The bracket is particularly suitable for installation in cramped ship interiors where floor mounting is not possible or not desired.The bracket is riveted to the stove body.

€69.81 *

Details

Spare burner pot REFLEKS

It is possible, that a replacement becomes necessary after years of usage, since the burner chambers in all REFLEKS oil heater are made from steel plate.The chambers are shipped complete with welded infeed tube, with a stainless steel ring to direct the flame and in case of the small burners 66M, 71M and 62M also with the heater coil (catalyst) made from innox.With the larger burners the heater coil has to be ordered separately.Additional spare parts for the REFLEKS oil heaters not mentioned here, like burner base, new burner or heating coil are available on request.

From €217.00 *

Details

Exhaust hood REFLEKS

Standard exhaust hoods REFLEKS.

From €131.00 *

Details

Exhaust hood Yacht REFLEKS

Thin flue cap, type YACHT.The design of this cap ensures a very secure fit and a good draft.Rain-proof and very compact.The rounded edges keep lines from hooking on it.

From €165.01 *

Details

H-exhaust hood REFLEKS

The flue cap of the Danish fishermen.The cap offers the most safe adjustment and is exceptionally secure against down drafts.Fits the double-walled flue pipes.

From €209.00 *

Details