This flue pipes matches the REFLEKS heating system and other gas or coal stoves with matching exhaust outlets.Made of acid-proof stainless steel (wall depth 0.6 mm).Plugs together: slightly conical with pressed sleeve on one side.
Thin flue cap, type YACHT.The design of this cap ensures a very secure fit and a good draft.Rain-proof and very compact.The rounded edges keep lines from hooking on it.
Guard for flue pipes that are installed in close quaters.Avaiable in stainless steel, brass or copper plate.The risk of contact burns is minimized, but the warmth of the pipe can still be enjoyed.Matches REFLEKS flue pipes of 70 mm or 90 mm.The flue guard is attached to the flue pipe and fixed with two stainless steel brackets, which are included in the package.Distance from flue pipe, 15 mm.
Rotating stainless steel vent that can also be used as a gas vent for all opening types, protected against backdrafts and supports the correct draft of the chimney.The (folding) extraction fan runs on ball bearings and is propelled by the wind.The flange is made of a light DURAL-INOX alloy. Available is also a version 240 C with a square ground plate (330 x 330mm) for profiles of 200 x 200mm up to 250 x 250mm. The enclosed attachment bolts allow mounting on pipes of varying diameters.Output data based on 3 beaufort wind velocity (10 kn).
Through-deck fitting with round, inclined deck plate.Made of stainless steel.Avaialable in various angles for adapting to the deck inclination.Fits the REFLEKS flue pipes.
This flue pipes matches the REFLEKS heating system and other gas or coal stoves with matching exhaust outlets.Made of acid-proof stainless steel (wall depth 0.6 mm).Plugs together: slightly conical with pressed sleeve on one side.
Thickness 0.6 mm, insulated with 10 mm of rock wool.Above all, at the lowest temperatures, double flue pipes are necessary outside, so that the draft through very cold pipes can be restricted.
The flue cap of the Danish fishermen.The cap offers the most safe adjustment and is exceptionally secure against down drafts.Fits the double-walled flue pipes.
By REFLEKS especially for their different stoves pre aligned oil metering valves by the swiss manufacturer TOBY.The oil metering valves are equipped with an attached safety valve with a fusible cut-out for the automatic cut-off when the stove is overheating above 100°C. Fitting tubing: copper tube with D = 8 mm;Inlet and overflow pipe: compression type fitting,Outlet: flare type fitting.The TOBY oil metering valve DVR 5 is a time-tested single compartment controller for oil stoves, that operates with the gasification technique. The controller serves to regulate the amount of oil flowing and thereby the heating output. At the same time it acts as the safety valve for the stove.Since the CC oil metering valves used by REFLEKS before 2012 are not produced any more, a change to the TOBY oil metering valve became necessary.
This flue pipes matches the REFLEKS heating system and other gas or coal stoves with matching exhaust outlets.Made of acid-proof stainless steel (wall depth 0.6 mm).Plugs together: slightly conical with pressed sleeve on one side.
Thickness 0.6 mm, insulated with 10 mm of rock wool.Above all, at the lowest temperatures, double flue pipes are necessary outside, so that the draft through very cold pipes can be restricted.
Pipe socket with draft flap for draw regulation and performance improvement of REFLEKS stoves.The exhaust ventilation is installed directly over the stove and when used automatically guides air into the exhaust guide pipe.Recommended for long or problematic exhaust leads.Length 330 mm.
It is possible, that a replacement becomes necessary after years of usage, since the burner chambers in all REFLEKS oil heater are made from steel plate.The chambers are shipped complete with welded infeed tube, with a stainless steel ring to direct the flame and in case of the small burners 66M, 71M and 62M also with the heater coil (catalyst) made from innox.With the larger burners the heater coil has to be ordered separately.Additional spare parts for the REFLEKS oil heaters not mentioned here, like burner base, new burner or heating coil are available on request.
Thickness 0.6 mm, insulated with 10 mm of rock wool.Above all, at the lowest temperatures, double flue pipes are necessary outside, so that the draft through very cold pipes can be restricted.
All REFLEKS heating systems with a water circuit should be equipped with this shut-off valve.The KBB fire protection valve is a compact valve in a corrosion-resistant, non-flammable design that operates purely mechanically and does not require a power supply.The temperature sensor is connected to the valve via a permanently soldered capillary line.As soon as the temperature at the sensor exceeds the set value (90°), the oil supply to the stove is immediately interrupted by the valve.The valve remains closed until the reset button is pressed.The valve can also be triggered manually by pulling the reset button.The valve (supplied with connection material for 8 mm pipes, SR 8 mm cutting ring fitting on both sides) is installed in the oil supply line directly upstream of the regulator.The temperature sensor measures the flow hot water temperature near the heater. If the set temperature (90°C) is exceeded, the oil supply is shut off immediately.To connect the sensor to the heating pipework, use a copper T-piece with two G ½" male threaded pipe fittings (please order item no. 4292-100 separately). The vertical branch of the T-piece does not have direct access to the water circuit of the heating system, but is soldered onto the water-carrying pipe and serves to accommodate the temperature sensor.Care must be taken during installation to ensure that the capillary line is not kinked under any circumstances. Length of the sensor line 200 cm.
Small reflector plate for heat protection behind flue pipes.Plate stainless steel.Measurements:50cm high, 15cm wide.Available as flat or recessed version.The flat plate must be mounted with spacers or insulation behind, the recessed plate can be mounted directly on the wall.
This adapter is suitable for the "SALAMANDER SE" and "LITTLE RANGE" stoves from SALAMANDER and enables the use of the stainless steel flue pipe system from REFLEKS with a diameter of 114 mm.
Sturdy bronze cover that provides a secure closure for the exhaust system of the marine stove or ship's oven. Suitable for our bronze through deck fitting and REFLEKS stainless steel thru deck fittings.The bronze cap is fixed and secured with a small knurled screw.
Functional cookies are absolutely necessary for the functionality of the web shop. These cookies assign a unique random ID to your browser so that your unhindered shopping experience can be guaranteed over several page views.
Session:
The session cookie stores your shopping data over several page views and is therefore essential for your personal shopping experience.
CSRF token:
The CSRF token cookie contributes to your security. It strengthens the security of forms against unwanted hacker attacks.
Timezone:
The cookie is used to provide the system with the user's current time zone.
Cookie settings:
The cookie is used to store the cookie settings of the site user over several browser sessions.
Cache handling:
The cookie is used to differentiate the cache for different scenarios and page users.
Information on origin:
The cookie stores the referrer and the first page visited by the user for further use.
Activated cookies:
Saves which cookies have already been accepted by the user for the first time.
CAPTCHA integration
Age check / minimum age:
Check of age for specific catgories and products
PayPal payments
Wishlist
YouTube video
Google Maps:
We use Google Maps to display maps. For this purpose, we integrate an external service from Google, which may access and evaluate personal data. Privacy policy of Google
Youtube / Vimeo:
This cookie is required for playing youtube videos which use cookies.
Matomo Tracking:
Tracking statistics for the optimization of user workflows. No personal data is stored.
language-redirected
Marketing cookies are used to display advertisements on the website in a targeted and individualized manner across multiple page views and browser sessions.
Google Analytics
Morayne:
Enables the optimization of various functions, such as the search in our shop.
Google Advertising
Stored data:
Shopware Analytics adds the following information to your browser's local storage until consent is revoked: _swa_anonymousId (a unique identifier of the visitor), _swa_userTraits (user traits of the visitor).
Google Tag Manager
Google Analytics
Google Ads
Here you can choose which cookies are enabled. You can choose between cookies that are necessary for the operation of the website and additional marketing cookies. If you select all cookies, we will collect data for the analysis and control of advertising campaigns.
Request sent successfully
Request wasn't send - a error occured. Please try again.
