A4 railing bracket 1"14TPI for GPS/radio antenna

These small diplexers allow the simultaneous use of a VHF radio, a FM/AM radio and an AIS device, using only a single antenna.Output max. 30W/channel, for frequencies 156-162 Mhz, 163 Mhz (AIS), 0,5-108 Mhz. Available are two versions: VHF / AIS / AM/FM:Active crossover switch, with output for VHF telephone, VHF/AM/FM radio, AIS receiver (only for receiving AIS informations, not for transmitting) Switch is wired for VHF telephone and AIS receiver with 50 cm of cable and matching PL plugs. Radio-out: F socket for F plug. Antenna-in: PL socket.Operating voltage: 12-24 V, current 0,04 Amps. Plastic housing. VHF / AIS transponder / AM/FM: Active crossover switch, with output for VHF, AM/FM radio, AIS transponder (receiving and transmitting of AIS informations). Completely wired for VHF and AIS with 100 cm cable and matching PL plugs.Operating voltage: 10-30 V, current 0,1 Amps. Metal housing.

Stainless steel adapter to fit a CX antenna to a standard tube with outer diam. 26mm.One side with 1" BSP outer thread for the union nut f the antenna, opposite side to a tube with outer diameter 26mm.Hex socket screws to fix the adapter to the tube.The cable may go through the fitting into the tube..

Adapter tube made of A4 stainless steel, for mounting a CX antenna (with union nut 1" BSP) on an antenna base with thread 1" x 14TPI.Adapter threads:matching 1" BSP male thread on one side for the union nut of the CX antenna,one side female thread 1" x 14TPI, suitable for antenna bases with 1" x 14TPI male thread.The tube has a long slot on the side through which the antenna cable can be routed to the outside.

Masthead bracket GLOMEX V9173 from stainless steel - mast mount with standard thread 1" x convolution 14 standard thread (1" x 14TPI).Can be installed on sailingboats & motorboats.Weight: 330g.

Masthead bracket from stainless steel with arm for side mount. Male thread 1" x 14 TPI.

Masthead bracket from stainless steel with flat screw nut 1" 14TPI.May be installed on sailboat or motorboat masts.

Rotatable antenna mounts made from stainless steel for the installation of GPS and VHF antennas on horizontal rails of 22mm - 25mm. Standard antenna thread: 1" x 14 TPI.

Antenna mounts made from stainless steel for the installation of GPS and VHF antennas on horizontal rails of 22mm - 25mm. Standard antenna thread: 1" x 14 TPI.

Tiltable socket for VHF or GPS antennas with standard thread 1"x14TPI. For deck or bulkhead mounting.Sturdy version made from stainless steel A4.

Rotatable antenna mounts made from white polyamide (PA) for the installation of GPS and VHF antennas on horizontal rails of 22mm - 25mm. Standard antenna thread: 1" x 14 TPI.

Antenna mounts made from white polyamide (PA) for the installation of GPS and VHF antennas on horizontal rails of 22mm - 25mm. Standard antenna thread: 1" x 14 TPI.

Different types of antenna sockets. All sockets are suitable for VHF or GPS antennas or active radar target enhancer with standard theads 1" x 14 TPI. Available versions:GLOMEX long, stainless steelstandard long, stainless steelstandard short, stainless steelstandard short, white plastic (PA)

Tiltable antenna base with a base plate for deck or bulkhead mounting.The mount is suitable for VHF and GPS antennas with a 1"x14TPI thread.Made of white polyamide (PA) plastic. The adjustment knob prevents lines from getting caught on the mount.

Practical wind indicator for the VHF antenna, suitable for all 2,5mm stainless steel rod antennae.Easy to mount, with adjustable angular arms, 380 mm pointer length.Delivery without VHF antenna.

Ground plates made from special porous material from bronze, with as large a surface as possible, are especially well suited for VHF radios.They improve the reception and range. They proved their worth with GPS units, weather decoders, weather fax receiver, as well as ham and shortwave radios.The plates are fixed with bolts to the hull and connected to the apparatus via cable.Shipping with screws and nuts from bronze.

GLOMEX V9124 Universal Mount made of electropolished A4 stainless steel.This non-threaded mount is suitable for 25 mm (1") pipe mounts on TV antennas or Wi-Fi antennas. It has a height of 150 mm.Compatible with GLOMEX IT1205EPLUS or IT1205EPLUS/BK weBBoat® ePlus 5G / Black Wi-Fi antennaGLOMEX VT300 or VT300-BK Avior / Avior Black TV antennaGLOMEX V9125AGCU/DAB20 Talitha AGC DAB 20 TV antennaGLOMEX V9126AGC Altair AGC TV antennaGLOMEX V9112AGCU/DAB20 Nashira AGC DAB 20 TV AntennaGLOMEX V9150AGC/DAB20 Adhara AGC DAB 20 TV Antenna

The robust adapter allows you to connect an external antenna with BNC connector to an ICOM handheld radio.The external antenna (e.g. in the masthead of your sailing yacht) can be used to significantly extend the range of the handheld radio (e.g. after a failure of the built-in radio).The antenna adapter fits the ICOM handheld radios IC-M25 EURO EVO, M33, M35, M37E, M73, M91D, M93D, M94DE.

Isolator for installation on antenna wires or stays which are used for antennas. Lloyd Register qualified.Skilled processing means the breaking load of the appropriate wires is not reduced.Approved Norseman terminals on both sides.

With this isolator backstays and shrouds can be made into effective radio antennas. The isolator must be installed in two intertwined wire eyes. The cleanly milled grooves thereby allow the wires a large bending radius, through which they are able to retain their strength.Made from the saltwater-resistant plastic Polyacetal (POM).

The Philippi UKW 3130 control panel is a compact protection device for onboard VHF radio systems. The switch, featuring a two-pole thermal circuit breaker (10 A) and an integrated LED status indicator, is designed to visually complement Philippi control panels from the 100 Series (e.g., STV 088 or STV 08) or the 200 Series.Technical SpecificationsA two-pole thermal circuit breaker (10 A) reliably protects the VHF radio system against overloadIntegrated LED operating indicator shows the switch status at a glanceDimensions: W x H x D 65 x 50 x 60 mm

PL-plugs and accessories for VHF-antennas.

KOAX cable for VHF, D=10mm.

Fibreglass antenna with practical mounting bracket, which can be used to continue operating the radio system on superstructures or stationary equipment in an emergency (after mast breakage or similar damage), for example.Permanently mounted cable (4.5 m long) with PL plug, which can be quickly connected to any stationary radio device.Supplied with cable in practical plastic bag.Antenna length 240 mm.

Fiberglass VHF rod antenna CX, 156-163MHz. 3 dB gain.Length overall 130 cm, antenna 120 cm, weight 0.5 kg.With chromed union nut 1"BSP and PL-socket.For mounting with a standard deck or rail fitting with 1"x14TPI threads an additional adaptor Art-Nr. 3940-102 is required (which is not supplied with the antenna).