Spare exenter for electric diaphragm pump EVS

We deliver a lot of spare parts for the WHALE GUSHER TITAN bilge pump.

Spare parts for WHALE GUSHER 30 bilge pump.The service kit (neoprene) contains all wearing parts for the GUSHER 30:2 membranes2 dampers2 inlet valve & seal1 outlet valve2 holder valves2 Valve gasket4 Nylon M10 washers2 screws No 6x11/4"The replacement lever is made of stainless steel (450mm) and is supplied with a safety line.A detailed overview of spare parts can be found under "Downloads". We can supply all spare parts on request.

We deliver a lot of spareparts for the WHALE GUSHER URCHIN bilge pump.

Deckplate and bridge for WHALE-pump Gusher 30, for deck or bulkhead mounting. Provides a neat cover over manual bilgepumps. Manufactured from aluminium cast. Snap-shut lid remains closed when pump is not in use.

The MARPOL Convention prohibits the discharge of oily wastewater into the sea. This filter removes the oily substances from the pumped bilge water by a patented filter system, so that the bilge water can be pumped out almost without oil residues and the water pollution is minimized.The filter is installed behind the bilge pump and in front of the ship's passage. It is suitable for oil residues, large dirt must be removed from the bilge before.Supplied with a stainless steel wall mounting plate.Replacement filter cartridges are available, annual replacement is recommended.LLOYD'S REGISTER Type Approved.

Holding brackets, fit our brass hand bilge pump.Stainless steel.

Deckplate for HENDERSON/WHALE pump MK5 for deck or bulkhead mounting. Provides a neat cover over manual bilgepumps. Manufactured from UV stabilised plasic, will not fade or discolor. Snap-shut lid remains closed when pump is not in use.

Deckring without lid for WHALE-pump MK5 (BP0535) for deck- or bulkhead mounting.Manufactured from white, UV-stabilised plastic.

Deckplate for WHALEpumps for deck or bulkhead mounting. Provides a neat cover over manual bilgepumps. Manufactured from UV stabilised plasic, will not fade or discolor. Snap-shut lid remains closed when pump is not in use.Article-no. 1860-110 (DP8904) fits for Gusher 10, Urchin, Titan.

Deckplate for WHALE-pumps for deck or bulkhead mounting. Provides a neat cover over manual bilgepumps. Manufactured from aluminium cast. Snap-shut lid remains closed when pump is not in use. 1860-111 (DP3804) fits for Gusher 10 and 30 or Gusher Urchin.

Accessory for bilge water filter WAVESTREAM.

Service kit for WHALE/HENDERSON deckplates suitable for underdeck models Gusher 30 and 10, Titan, Urchin, Mk5The kit includes a gaiter (diameter 108mm) and an O-ring.

Accessory for JABSCO impellers: JABSCO impeller grease, 2,5 ml tube.

The Italian FINNORD group produces impellers in OEM quality for different manufacturers of pumps and offers a wide assortment of replacement impellers under the name CEF at reasonable prices.Here we present a selection of popular impellers made from neoprene and nitrile rubber.Usualy shipping complete with matching paper cover gaskets. To see the matching image for the impeller, simply click on the part number in the table below.Other sizes are available.

Impeller of special nitril rubber. Original spare part for UP1, UP1-M and UP1/AC MARCO Pumps.Dimensions hight x Ø: 22 x 51.5 mm.Bore Ø: 8 mm.

Impeller IMP2 of special nitril rubber. Original spare part for UP1-J and UP1-JR MARCO pumps.Dimensions hight x Ø: 22 x 40.5 mm.Bore Ø: 8 mm.

Spare impeller for JABSCO pumps.

Original JABSCO impeller for installation on most cooling water bilge pumps and universal pumps.To keep motors and pumps running smoothly, choosing the right impeller is critical. In addition to the hub mount and size, the material of the impeller should match its application:Neoprene is the most commonly used material for impellers and is suitable wherever only small amounts of oil or diesel fuel are present. Neoprene impellers are therefore suitable for engine cooling and for salt or fresh water pumping.Nitrile is oil resistant and can also be used for heavily polluted water. Impellers made of nitrile are therefore suitable for bilge and bilge pumps.The impellers are usually supplied with a matching paper cover gasket.Other JABSCO impellers and spare parts are also available at short notice on request.To see the matching image for the impeller, simply click on the part number in the table below.

Outlet elbows for the diaphragm pump PLASTIMO model 11722.They are screwed and fitted with an O-ring for perfect water tightness and added safety (quick release facility). For a tube diameter of 38mm.

Repair kit #0350095 for the RHEINSTROM diaphragm pump M50 and M50E.The set consists of the pump membrane, a large seal and three valve flaps made from plastic.

Replacement filter AK1319 for WHALE pressure water pumps of the WATERMASTER and UNIVERSAL types. For 15 mm WHALE QUICK CONNECT system.Technical featuresDesign: coarse filterConnection: 15 mm Quick ConnectCover: transparent cover for visual inspection; cover can be removed for cleaningWHALE No.: AK1319For UNIVERSAL models: UF0812, UF0815, UF1212, UF1214, UF1215, UF1225, UF1815, UF1825, UF2014, UF2015, UF8015, UF8025For WATERMASTER models: FW0814, FW0814B, FW1214, FW1214B, FW1215, FW1215B, FW1225, FW1225B, FT0814, FT0814B, FT1214, FT1214B

Spares for FYNSPRAY galley pump WELLINGTON.Please check if your older pump has got a piston seal of leather or a newer pump one of rubber!

Accessories for brass hand bilge pump, manufactured before 2012.

Accessories for brass hand bilge pump.