OWATROL TRANSYL Rust Remover

BALLISTOL UNIVERSAL OIL is a biodegradable, skin-friendly multifunctional oil for cleaning, maintenance, lubrication, and corrosion protection. The oil has been manufactured since 1904 using an unchanged formula and is based on a mildly alkaline composition with lanolin and is free of silicone, PTFE, and acid. It does not resinify and is emulsifiable in water.Usable in industry, shipping, agriculture, household, outdoor activities as well as for machines, tools, leather, wood, rubber, and even for use on humans and animals.Application: BALLISTOL Universal Oil can be used as a rust protection, lubricant, penetrating or contact oil. It dissolves tar, grease, adhesive residues, and other unsuitable oils, neutralizes weak acids (e.g. hand sweat), and is suitable for the care of leather, natural wood, and oil-resistant plastics. Application is done with a cloth or brush. Technical DataApplication area: Corrosion protection, lubrication, cleaning, maintenanceSubstrate: Steel, iron, leather (except suede), natural wood, rubber, plasticCoverage: depends on application method Thinning: not requiredApplication method: cloth, brushDrying times: not applicable; remains active and does not resinifyFor more information on application, please refer to the Technical Data Sheet under 'Downloads'.

BALLISTOL UNIVERSAL OIL is a biodegradable, skin-friendly multifunctional oil for cleaning, care, lubrication and corrosion protection. The oil has been produced according to the same recipe since 1904 and is based on a slightly alkaline formula with lanolin and is free from silicone, PTFE and acids. It does not resinify and can be emulsified in water.Can be used in industry, shipping, agriculture, household, outdoor activities as well as for machines, tools, leather, wood, rubber and even for use on humans and animals.Application: BALLISTOL Universal Oil can be used as a rust protection, lubricating, penetrating or contact oil. It dissolves tar, grease, adhesive residues and other unsuitable oils, neutralizes weak acids (e.g. hand perspiration) and is suitable for the care of leather, natural wood and oil-resistant plastics. It is applied by spraying &nbsp

The BALLISTOL PTFE Dry Lubrication Spray is suitable for clean dry lubrication of sensitive areas. It is free from oil, grease, and silicone. Finest PTFE particles adhere even to microscopically small surface irregularities, thereby reducing adhesion, sliding, and rolling friction, and protecting against dirt and dust deposits. The spray is highly compatible with materials and suitable for all common materials.The spray is suitable for consistent and long-lasting lubrication of rollers and bearings, sliding guides and rails, cable pulls and telescopic guides, gears and cogs, as well as plastics of all kinds.Application: Shake well before use. Spray the product onto the cleaned surface from a distance of 10–25 cm and allow it to dry for a few minutes. A barely visible, dry film remains.Hazard information: Extremely flammable aerosol. Container is under pressure: it may burst when heated above 50°C. Causes serious eye irritation. Further information can be found below under "Downloads & Information".Technical dataApplication area: Dry lubrication in guides, bearings, gears, cable pulls, plastic and metal jointsSurface: Metal, plastic, rubber – clean, grease-free, dryPrimer: not requiredYield: dependent on application area (spray application)Thinning: not requiredApplication method: Aerosol sprayDrying times: short, depending on ambient temperatureFurther processing information can be found in the technical data sheet under 'Downloads'.

Penetrating oil based on natural oils, which is used as an additive to improve the flow properties of conventional and semi-synthetic paints. It reduces visible brush strokes, impregnates wood and has a rust-inhibiting effect on steel by penetrating deep into the substrate. This means that a favorable result can be achieved even under difficult conditions.

The Zinc Spray from EURO LOCK offers a fast-drying corrosion protection with excellent long-term effect for all metals. It is suitable for use on thermally stressed parts such as intake manifolds, heat exchangers, oil coolers, etc. It is electrically conductive and heat resistant up to 500 °C.Additionally, it is suitable for reworking or repairing defects on hot-dip galvanized parts, and for touching up damaged zinc coatings.Also suitable for refreshing galvanized anchors, anchor chains, and for repairing welding and sheet metal work. Prevents rust and provides good protection against extreme weather conditions. Zinc content approx. 95% in the dry film. Can be overpainted with most one- and two-component primers and paints.Technical DataSubstrates: All metalsPretreatment:Surface must be clean, dry, free of grease and oilShake can well for approx. 2 minutes before useTest spraying recommendedSubsequent coating: Can be overpainted with many paint systems (own testing recommended)Coverage: No informationApplication method: Spray from approx. 20–30 cm distance in a crisscross patternDrying times at 20 °C: Dust-dry after approx. 8 min; tack-free after 20–30 min; fully dry after 48 hrsFurther information on application can be found in the technical data sheet under "Downloads".

Thixotropes Rostschutzmittel auf Lanolin-Basis in der Sprühdose, das zugleich als Rostlöser und Gleitmittel wirkt. FLUID FILM AS-R SPRAY bildet einen klaren, glänzenden Schutzfilm und eignet sich zur Konservierung und Pflege von Metalloberflächen in Fahrzeugen, Booten, Maschinen und Haushaltsgeräten.Das Produkt wird durch Regen und Seewasser weder abgewaschen oder verändert, außerdem verhält es sich temperaturstabil und ist äußerst widerstandsfest gegen alle Witterungseinflüsse, auch Schnee.  Im Gegensatz zu herkömmlichen Produkten ist FLUID FILM AS-R durch seine lösungsmittelfreie Zusammensetzung umweltfreundlicher und sparsamer im Gebrauch. Die Sprühflasche enthält FLUID FILM NAS mit Propan-Butan als Treibgas.Anwendung: Untergründe von losen Verschmutzungen befreien, Flächen können trocken oder feucht sein, jedoch ohne Oberflächenwasser. Gleichmäßig aufsprühen, auch in schwer zugänglichen Bereichen mit Sprühröhrchen. Dose sprüht in jeder Lage. Anwendung bei Bedarf wiederholen. Sicherheitsvorschriften beachten: Dose steht unter Druck, nicht über 50 °C erhitzen, nicht ins Feuer sprühen, brennbar.Technische DatenAnwendungsbereich: Fahrzeuge, Boote, Industrieanlagen, Werkzeuge, Maschinen, Waffen, Freizeit- und HaushaltsgeräteUntergrund: Trockene oder feuchte Oberflächen, frei von losen VerschmutzungenViskosität: niedrig (wie Sirup)Ergiebigkeit: Abhängig von Objektgröße und AnwendungApplikationsmethode: Sprühen mit Standarddüse oder SprühröhrchenTrocknungszeiten (bei 20 °C): Kriechend und haftend, bildet nach kurzer Zeit einen beständigen SchutzfilmWeitere Informationen zur Verarbeitung finden Sie im Technischen Datenblatt unter 'Downloads'.

Solvent-free, soft coating material based on lanolin (wool fat). FLUID FILM Gel BN is a physiologically safe and environmentally friendly corrosion protection agent. It serves as a single-layer long-term protective coating for ships, docks, offshore units, and similar objects when surface preparation is limited to high-pressure washing. The viscous gel can be used as a lubricant for machines, equipment, winches, and for wire rope preservation. The product offers excellent corrosion protection, lasting up to 20 years in enclosed spaces. It penetrates residual rust, and promotes the self-healing effect in case of damage to existing coatings. FLUID FILM Gel BN is temperature stable from -45 °C to +70 °C. Complies with MIL-Spec C-23050 guidelines. Preparation: Loose components, dirt, rust, and standing water must be removed before application. Surfaces must be dry.Application: FLUID FILM Gel BN can be applied using a brush, roller, spatula, or airless spray. The greater the layer thickness, the better the corrosion protection. Due to its gel-like consistency, thicker layers up to 1000 µm can be applied. The material can be used directly from the container. For areas with strong water turbulence, it is recommended to subsequently apply an additional layer of PERMA FILM (Art.No. 2718-501). Technical DataApplication area: Long-term protection for ballast tanks, voids, offshore structures, and metal partsSubstrate: Clean, dry, free from loose components; high-pressure cleaning recommendedLayer thickness: 600–1000 µm (airless spraying), 80 µm (brush/roller)Coverage: approx. 1.6 m²/l (at 600 µm), approx. 12 m²/l (at 80 µm)Application temperature: -10 °C to +40 °CApplication methods: Brush, roller, spatula, airless sprayingColor: Transparent (Gel BN)Temperature resistance: -45 °C to +70 °CFurther information on application can be found in the Technical Data Sheet under 'Downloads'.

FLUID FILM LIQUID A is a transparent, solvent-free, oil-based corrosion protection based on lanolin (wool grease) for soft coating of steel surfaces in above and underwater areas.The product displaces water, penetrates existing rust, and forms an elastic, adhesive protective film. It was originally intended for flooding repair-needed ballast water tanks on ships, floating docks, offshore units, for flooding coating of cavities, ballast water tanks, offshore structures, and hard-to-reach areas. The protective film lasts up to two years in enclosed cavities. Additionally, it is suitable for loosening seized rust or making rusted metal parts movable. Application on damp or slightly corroded surfaces is also possible.The product contains no solvents, is environmentally friendly, and easy to apply. Available as spray (type AS-R), in cans or containers (for dipping, spraying, or brushing).Application: Application is carried out depending on the area of use by flooding, brushing, rolling, or spraying. The material should be homogenized before use. After application, the gel time when flooding is about 3–4 hours. Application is possible at any temperature. Ensure adequate ventilation and personal protective equipment.Technical DataField of application: Single-layer corrosion protection on steel surfacesSubstrate: Steel (bare, rusty or damp); no special pretreatment necessaryPrimer: not requiredCoverage: approx. 12 m²/l at 80 µm wet film (roller, brush application)Thinning: not necessaryApplication method: Brush, roller, spraygun, flooding (professional users)Drying times: none; forms a non-drying, oily protective filmFor more information on application, refer to the technical data sheet under 'Downloads'.

Classic metal preservation from the commercial shipping industry. HANSALUX U SCHIFFSBODENÖL is an aromatic-free, high-solids coating based on linseed oil and a special alkyd resin. It is suitable for wooden substrates and hand-rusted steel surfaces above water.This aromatic-free preservative is primarily used where sandblasting and the use of a rust machine are out of the question, such as on inboard walls, in the bilge or in the anchor locker.&nbsp

"TONKI" - the classic! Glossy, clear varnish oil for wood and metal. The formulation of LE TONKINOIS varnish oil is based on a special formula in which high-quality linseed oil and Chinese wood oil (tung oil) are cooked together. This creates a natural product without chemical additives. The varnish oil is suitable for indoor and outdoor use as well as for application under extreme weather conditions. It forms a resistant, elastic protective film with high UV resistance and highlights the natural grain of the wood.Application: LE TONKINOIS VARNISH is applied to untreated or cleanly sanded wood. Application is done with a brush or roller; for spray application, it can be diluted up to max. 10% with the appropriate LE TONKINOIS thinner. Only one thin coat should be applied per day. Stir well before use, do not apply below 12 °C.Technical DataArea of application: Wood and degreased metals indoors and outdoors, also under extreme weather conditionsSubstrate: Untreated wood, wood-based materials, limited use on corkCoverage: 20 m²/l Thinning: Max. 5–10% with LE TONKINOIS thinnerApplication method: Brush, flat brush, sprayingDrying times (at 20 °C): Dust dry after 6–8 h, reworkable after approx. 24 h, walkable after 3 days (with 2–3 coats)Further information on application can be found in the technical data sheet under 'Downloads'.

Universal marine grease for the many lubricating points on board, water-repellent, saltwater resistant and stable to ageing and liquefying.

Premium primer that combines the properties of a rust protection primer and an air-drying natural oil with high solids content and exceptional penetrating properties. Thanks to the formulation with OWATROL oil, OWATROL CIP has a low surface tension and is three times "wetter" than water. This allows it to optimally wet surfaces and penetrate even hard-to-reach corners that may not be mechanically derusted. It penetrates thick rust layers down to the "sound" metal and displaces moisture and air.The oil dries completely, even in thick layers given sufficient drying time. After drying, it remains elastic but is hard enough due to the added primer to be coated with a subsequent one- or two-component system such as an epoxy or chlorinated rubber primer. Suitable for all areas exposed to extreme climatic conditions, such as ballast tanks. Active ingredients: water-displacing penetrating oil and iron oxide.Technical DataSubstrate: Iron, steel, cast iron, stainless steel, light metals (bare or rusted)Surface preparation:Remove loose paint and rustFirm rust may remainSurface must be dry, grease-free and cleanFor chemically exposed surfaces: thorough cleaning with water or steamTopcoat: All one- or two-component systems including epoxy, polyurethane, chlorinated rubber etc.Coverage: up to 15 m²/l (depending on substrate and rust depth)Thinner: noneApplication method: Brush, lambskin roller, spray gun (professional use)Drying times at 20 °C: Touch dry after approx. 6 hrs; recoatable after 48 hrs.Further information on applying this product can be found in the technical data sheet under “Downloads”.Safety note: Cloths soaked with drying oils can self-ignite, therefore always spread out to dry before disposal or collect in sealed metal containers.

OWATROL GELCOAT RESTORER, also known as POLYTROL, is a tried and tested color refresher for metals, plastics, paints and gelcoats.The product refreshes faded colors of plastic or gelcoat surfaces, regenerates faded surfaces of marble, tiles or slate and restores shine to dull surfaces without leaving a greasy or oily film.The product is acid- and silicone-free, extremely penetrating and penetrates deep and sealing into microporous surfaces.Also suitable for the care of brass, bronze and stainless steel fittings.Application: Apply and spread evenly with a brush or clean cloth, spray from a distance of approx. 30 cm. After a maximum of 10 minutes, rub the surface dry with a absorbent, lint-free cloth, removing any excess product.Technical DataApplication area: Restores color and gloss on weathered plastic, gelcoat, paint, metal, plastic partsSubstrate: dry, clean, grease-freeApplication: cloth or lint-free rag; remove excess within 20 minCoverage: approx. 18 m²/l (depending on porosity and surface)Thinner: noneApplication temperature: +5 °C to +35 °CDrying (20 °C): fully dry after 24 hrs; no buffing requiredFurther information on application can be found in the Technical Data Sheet under "Downloads".

OWATROL OIL, which is based on natural oils and has exceptionally good penetration properties, is the basic product for many applications.It is three times wetter than water, i.e. it even creeps upwards. On rusty metal, it creeps deep into the rust pores and displaces the air and moisture (i.e. the actual cause of corrosion) even from inaccessible areas. After drying, the leaf rust can be removed more easily and the soaked residual rust is consolidated, preserved and sealed for the long term and can be painted with all turpentine-substitute thinnable paints.For use on larger surfaces or as a paint additive, OWATROL is suitable for painting from the can.Technical dataSubstrates: Rusty and bare metals (iron, steel, aluminum), new and weathered woodPre-treatment: depending on the material: remove loose rust, non-adherent old paint, oil and grease

OWATROL OIL, which is based on natural oils and has exceptionally good penetration properties, is the basic product for many applications.It is three times wetter than water, i.e. it even creeps upwards. On rusty metal, it creeps deep into the rust pores and displaces the air and moisture (i.e. the actual cause of corrosion) even from inaccessible areas. After drying (24 hours at 20°C), the leaf rust can be removed more easily and the soaked residual rust is consolidated, preserved, sealed and can be painted with all turpentine substitute thinnable paints.OWATROL-OIL is also ideal as an additive (color additive) for 1-component paints. Instead of using turpentine substitute as a thinner, it significantly improves the coating and flow properties and ensures optimized adhesion without compromising the quality of the paint. On the contrary, the addition of 10-15% OWATROL OIL makes paints and varnishes even more porous and durable on the surface.OWATROL spray is suitable for minor touch-ups.Technical dataSubstrates: Rusty and bare metals (iron, steel, aluminum), new and weathered woodPre-treatment: depending on the material: remove loose rust, non-adherent old paint, oil and grease

Highly penetrating, acid-free universal oil in a practical spray bottle for precise dosing.OWATROL TRANSYL is an excellent screw remover, displaces moisture, breaks down rust and prevents new rust formation. A good lubricant that does not attack substrates such as metals, plastics and paints.Application: Shake spray thoroughly before use. Do not spray on hot surfaces. Cover adjacent areas. Spray the product onto the areas to be treated, either selectively or over the entire surface &nbspTechnical DataApplication area: Metal connections, bolts, hinges, bearings, guidesSubstrate: rusty or bare metal, plastics, paintApplication: spray canCoverage: depends on usage (spot or area-wide)Thinner: noneApplication temperature: –30 °C to +50 °CDrying (20 °C): very slow evaporation, leaves lasting lubricating filmFurther information on application can be found in the Technical Data Sheet under "Downloads".

Zinc dust-containing (67%), surface-tolerant 2-component epoxy primer with high penetration properties, even on steel surfaces that have only been derusted by hand or water-blasted. The pigment-rich formulation results in a very well adhering and robust cathodic corrosion protection layer for use above and below water.HANSAZINC ST tolerates residual moisture (no wetness) and slight flash rust formation. Can be painted over with two-component paints as well as with bitumen, vinyl and chlorinated rubber primers, but not with alkyd resin-based paints and paints containing zinc phosphate. Not suitable for use on galvanized, stainless, light or non-ferrous metals, wood, mineral substrates or plastics.Application: The mixing ratio is 93:7 (base:hardener) by volume. The pot life is 3-4 hours. Depending on the substrate, the product can be applied by spraying, brushing or rolling. On hand-rusted surfaces, the coating must be worked in intensively; a bristle brush is best suited for this. Ideal processing and surface temperatures are between 15 °C and 25 °C and at least 5 °C above the dew point.&nbsp

Permanently elastic, slow-drying, single-component thick grey film paint that can be applied to surfaces preserved with FLUID FILM Liquid A and prevents washout. This calcium phosphate compound dissolved in resin provides effective corrosion protection for all bare, rusted, or previously painted ferrous metals. PERMA FILM AL is suitable for ballast water tanks, offshore structures, machine components, and hard-to-derust areas such as the bilge.The lamellar pigment structure forms a barrier against water and oxygen, even on incompletely derusted or damp substrates. The paint can also be applied at low temperatures and is particularly resistant to saltwater.Surface preparation: Clean the surface (high-pressure wash) and remove loose particles with a wire brush. Surfaces may be surface damp but without water droplets. A thin coat of FLUID FILM LIQUID A is recommended as a primer. This combination keeps the system flexible, cures on the surface, and combines the positive properties of FLUID FILM’s penetration capability with those of a solid protective layer.Application: The product can be applied by airless spraying, brush, or roller. PERMA FILM can be processed directly from the container; thinning is not necessary at temperatures above 15 °C. For a new coating, apply two layers; the first with 150, the second with 250 µm wet film thickness (equivalent to 100 and 150 µm dry film thickness).During application and drying, sufficient ventilation must be ensured to guarantee uniform drying. A respirator must be worn when spraying. The drying process can be accelerated by using warm air.Technical DataApplication area: Coating of ballast water tanks, offshore installations, machines, equipment, steel surfacesSubstrate: Steel, also hand-derusted (St 2/St 3) or HD-cleaned (Wa 2); dry or damp surfacesPretreatment: optional: FLUID FILM LIQUID A (Art.No. 2717-001) Coverage: approx. 2.5 m²/l at 250 µm dry film thicknessThinning: optional, at temperatures below +15 °C: Special cable cleaner PF-SolventApplication method: Brush, roller, airless (professional users)Drying times (at 20 °C): water-resistant after approx. 30 hrs at 200 µm film thicknessFurther information on application can be found in the Technical Data Sheet under 'Downloads'.

WICHINOX PASSIVATION GEL from french manufacturer WICHARD is a cleaning and passivation agent for the maintenance of stainless steel parts in maritime and industrial environments. The gel formulation makes application easier even in hard-to-reach areas and ensures effective restoration of the protective passive layer on stainless steel.The product helps to remove tarnished surfaces and light corrosion marks on stainless steel fittings from Wichard, as well as other stainless steel components such as stanchions, handrails, or fenders. Application: Dismantle the parts to be treated if possible to avoid damaging adjacent surfaces. Ensure adequate ventilation and appropriate protective measures (e.g. gloves, safety goggles) during use. Stir before use. Apply the gel to the stainless steel surfaces to be treated with a brush and allow to act for 5–15 minutes. After the exposure time, rinse thoroughly. Do not apply to galvanized, painted, or anodized surfaces. Safety Note: Contains phosphoric acid. Harmful if swallowed. Causes severe skin burns and serious eye damage.Further information can be found in the Technical Data Sheet under 'Downloads'.