Bilge strainer WHALE MULTI | TOPLICHT

To be able to use the full range of Shopware 6, we recommend activating Javascript in your browser.

Art. No.	model	D (mm)	B (mm)	L (mm)	H (mm)	Price (unit)	Delivery time	Note list	Buy

Description

Bilge strainer with check valve, easy to clean.
With 19 mm hose connector.
The connector can be mounted in three directions: standing, horizontal, sideways.

Downloads

Datenblatt

Questions about the product?

Talk to craftsmen, boat builders and sailors. We understand your questions and provide the right answers.

Contact experts

Multiflex hose PVC

Multiflex hose PVC

Green transparent PVC hose for drinking water, bilge pumps (also suction side) and on-board toilets.Spiral strengthened and thick-walled version for use as suction or pressure hose.Approved for human consumption. Limited resistance to oil and grease (may harden).

From €4.90 *

Bilge strainer WHALE

Bilge strainer WHALE

With integrated check valve for hoses of 25 mm and 38 mm.With sieve on the onboard side.

€35.90 *

Bilge strainer WHALE standing

Bilge strainer WHALE standing

With integrated check valve for hoses of 25 mm and 38 mm.With sieve on the outboard side.

€35.90 *

Brass bilge water strainer

Brass bilge water strainer

Special brass, with non-return valve, strainer can be unscrewed.

From €21.00 *

Electric diaphragm pump WHALE GULPER 220

Electric diaphragm pump WHALE GULPER 220

WHALE GULPER type 220: Electric membrane pump for pumping the bilge or emptying the head or holding tank (grey water pump). Self-priming. Suction lift max. 3 m, dicharge head max. 3 m, combined suction lift / discharge head max. 4m.Odorless running, vibration absorbing rubber feet.Universal installation due to swiveling pump heads.For tube 19mm. Weight 1.5 kg. Dimensions: L x W x H = 273 x 111 x 117 mm. Spare-parts sets available.

From €198.00 *

WHALE field sensor bilge switches BE9003 / BE9006

WHALE field sensor bilge switches BE9003 / BE9006

This electronic level switch does not require any mechanics or moving parts. Two field sensors ensure functional switching on and off of the connected pump. The switch turns on at 51 mm water level and turns off at 13 mm water level. The automatic sensor type BE9006 switches with an automatic 30 seconds switch-off delay. This delay allows water to be pumped out even below the switching level of 13 mm. The test function can be used to check the function of the pump after installation.Voltage: 12 V / 24 V.Max. switch current: 20 A.Residual current: 0,008 A.

From €69.00 *

Switch panel for bilge pump SEAWORLD

Switch panel for bilge pump SEAWORLD

Switch panel for automatic bilge pump. With sound and light alarm when pump is running automtically.With toggle switch, positions: "automatic/off/manual". With control lights and fuse 16 A/12 V. For 12 volt systems.

€25.89 *

Thru-hull hose fitting polished or chromed

Thru-hull hose fitting polished or chromed

Through-hull with attached hose nozzle. Made of brass (seawater resistant brass, depending on manufacturer CW602N - CuZn36Pb2AS or CW625N - CuZn35Pb1,5AlAs).Comes in rolled brass or with a chromed finish.Thread type: BSPThread form: parallelThe thread sizes are nominal sizes, they do not indicate the thread diameter.

From €11.00 *

More Products from Category Check valves & bilge strainers

Bilge strainer WHALE

Bilge strainer WHALE

With integrated check valve for hoses of 25 mm and 38 mm.With sieve on the onboard side.

€35.90 *

Bilge strainer WHALE MULTI

Bilge strainer WHALE MULTI

Bilge strainer with check valve, easy to clean.With 19 mm hose connector.The connector can be mounted in three directions: standing, horizontal, sideways.

€64.90 *

Bilge strainer WHALE standing

Bilge strainer WHALE standing

With integrated check valve for hoses of 25 mm and 38 mm.With sieve on the outboard side.

€35.90 *

Brass bilge water strainer

Brass bilge water strainer

Special brass, with non-return valve, strainer can be unscrewed.

From €21.00 *

Brass check valve

Brass check valve

Brass check valve, spring operated.To be fitted in the tube to prevent reflux of water.With inner threads on both sides. Strong body of brass, valve cage of nylon, spring of A2 stainless steel, seal of nitrile rubber.The valve works in any installation situation.Thread type: BSPThread form: parallelThe thread sizes are nominal sizes, they do not indicate the thread diameter.

From €10.90 *

Brass screw-in sieve filter with stainless steel sieve

Brass screw-in sieve filter with stainless steel sieve

Screw-in sieve filter consisting of a brass body with an inch external thread and a sieve made of A2 stainless steel.Good for protecting the pump from coarse impurities when drawing in outside water or bilge water. Depending on the intended use, we recommend screwing the suction basket into a standpipe, a pipe-to-hose fitting or a non-return valve. See the example photos with corresponding accessories (not included in the scope of delivery).Thread type: BSPThread form: parallelThe thread sizes are nominal sizes, they do not indicate the thread diameter.

From €6.90 *

Check valve PLASTIMO

Check valve PLASTIMO

Plastic non-return valve with oil-proof nitrile rubber valve. Suitable for bilge water systems or hand and electric bilge pumps.The valve housing is easy to open (for maintenance). In narrow spaces, the straight gland can be replaced with an angled one.Entire length 185mm.Non-return valves are integrated into the suction hose, support suction and prevent backflow of water.

From €6.90 *

Check valve WHALE

Check valve WHALE

Small, spring-loaded ball check valve especially for drinking water hand pumps.The valves are installed directly in the suction hose (13 mm), as close as possible to the tank.It makes sense to install the valve if there is a problem with backflow into the fresh water tank and water has to be pumped for a long time until it flows out of the tap.Cannot be used in pressurised water and bilge pump systems.

€15.90 *

Check valve WHALE LV1219

Check valve WHALE LV1219

Made of glass fibre reinforced PP plastic with high-quality nitrile lip valve. Suitable for bilge water systems or hand and electric bilge pumps.Non-return valves are integrated into the suction hose, support suction and prevent backflow of water.

From €29.90 *

Non return valve from TRUDESIGN

Non return valve from TRUDESIGN

Non return valve made from glass fibre reinforced composite plastic fitted on both ends with a hose connector.The valve plug is made from nylon with a stainless steel spring, the length is 85 mm.Suitable for fresh water pipe systems. TRUDESIGN is the world leader in fittings made from composite materials. From its founding in 1974 the fittings are manufactured in New Zealand. Every TRUDESIGN part is made from high tensile composite GRP, a glass fibre reinforced Polyamide (6). The advantages are a high rigidity, temperature-resistance -40° to 80° C, resistant to oil and chemicals, of low weight, absolutely corrosion-resistant, electrically non-conductive and therefore especially suited for ship building materials which are galvanically sensitive like aluminium and steel.Every TRUDESIGN fitting has a tapered Whitworth pipe thread BSP (British Standard Pipe Thread) according to ISO 228-1, it is therefore fully convertible with fittings from brass, bronze or stainless steel. The shuttle valves and through hulls are approved and IMCI certificated after ISO 9093-2 (sea cocks and through hulls for pleasure vessels).

From €13.90 *

Non return valve JABSCO

Non return valve JABSCO

Non return valve made from plastic by the global market leader JABSCO with hose connectors on both ends and a check valve made from Nitrile rubber.Non-return valves are integrated into the suction hose, support suction and prevent backflow of water.

From €35.90 *

Non return valve WHALE

Non return valve WHALE

Made of glass fibre reinforced PP plastic with high-quality nitrile lip valve. Suitable for bilge water systems or hand and electric bilge pumps.Non-return valves are integrated into the suction hose, support suction and prevent backflow of water.

€35.90 *

RM69 non-return valve RM825 38 mm

RM69 non-return valve RM825 38 mm

The RM69 RM825 check valve is made of plastic and designed for hose lines in onboard water and bilge pump systems. It is suitable for hose connections with an internal diameter of 38 mm and comes in white. Function by means of a nitrile lip valve. Check valves are installed in the suction hose, support priming, and prevent water backflow

€29.00 *

Last seen products

Request sent successfully

Request wasn't send - a error occured. Please try again.