ENO No. 72645 Electronic ignition box with 4 connections.The ENO / FORCE 10 high-voltage ignition part is a genuine spare component for marine stoves and cookers. It reliably generates the required ignition spark, ensuring safe operation of your onboard gas cooking systems. Its compact design allows for easy integration into existing ENO / FORCE 10 appliances.Built with a durable construction, it is specifically designed to withstand the demanding conditions at sea. Replacing this part restores full functionality of the ignition system and ensures the operational safety of your cooking equipment.

ENO No. 72655 Electronic ignition box with 6 connections.The ENO / FORCE 10 high-voltage part for electric ignition is an original spare part for marine stoves and stoves. It reliably generates the necessary ignition spark and ensures the safe start-up of gas hobs on board. The compact design facilitates installation in existing ENO / FORCE 10 cooking systems.The robust construction is specially designed for use in a maritime environment and withstands the typical stresses at sea. Replacing this high-voltage part restores the full functionality of the ignition system and ensures the operational safety of your cooking appliances.

ENO No. 60026 Burner cap for large burners, outer diameter 95 mm.The cap is positioned above the upper part of the burner (flame ring) and is locked in place by a rotating movement on two pins protruding from the stove surface. This fixation ensures that both the upper part of the burner and the burner cap remain attached to the burner and cannot come loose due to vibrations.

ENO No. 63622 Pot holder left, for ENO / FORCE 10, stoves and ranges, made of stainless steel. Total length without locking knob 227 mm. Suitable for GASCOGNE, OPEN SEA, THE ONE from 12/2006 and various FORCE 10 models. The pot holder is fixed to the pot grate frame by screwing in the handwheel and can be moved back and forth as required by loosening it.Supplied without locking knob.

ENO No. 63624 Pot holder left, for ENO / FORCE 10, stoves and ranges, made of stainless steel. Total length without locking knob 272 mm. Suitable for GASCOGNE, OPEN SEA, THE ONE from 12/2006 and various current FORCE 10 models. The pot holder is fixed to the pot grate frame by screwing in the locking knob and can be moved back and forth as required by loosening it.Supplied without locking knob.

ENO No. 63623 Pot holder right, for ENO / FORCE 10, stoves and ranges, made of stainless steel. Total length without locking knob 227 mm. Suitable for GASCOGNE, OPEN SEA, THE ONE from 12/2006 and various FORCE 10 models. The pot holder is fixed to the pot grate frame by screwing in the handwheel and can be moved back and forth as required by loosening it.Supplied without locking knob.

ENO No. 63625 Pot holder left, for ENO / FORCE 10, stoves and ranges, made of stainless steel. Total length without locking knob 272 mm. Suitable for GASCOGNE, OPEN SEA, THE ONE from 12/2006 and various FORCE 10 models. The pot holder is fixed to the pot grate frame by screwing in the handwheel and can be moved back and forth as required by loosening it.Supplied without locking knob.

ENO No. 60032 All FORCE 10 stoves are equipped with a thermal sensor and an electric ignition on each gas burner.The thermocouples are sensors that only allow gas to escape from the valve when the flame is burning. As soon as the flame goes out - for example due to a gust of wind or boiling pots - the thermal sensor cools down and the gas supply is interrupted immediately.When igniting a gas burner, it should be noted that the thermocouple must first reach a certain temperature before the gas supply is released. This is done by holding down the gas control button for the corresponding burner for approx. 20 seconds after ignition so that the thermosensor does not interrupt the gas supply.The thermal sensors of the top burners on the stoves have been further developed over the years.SABAF II gas burners were used from 2000 to 2012, after which the more advanced SABAF III burners were used.The SABAF II burners can be recognized by the fact that their burner caps are fixed with two screws.the following thermocouples were installed in the top burners of the FORCE 10 gas stoves:Year of manufacture 2000 - 2012 Thermal sensor ENO no. F89216 (TOPLICHT item no. 4730-108)Year of construction 2012 - 2020 Thermal sensor ENO no. 60032 (TOPLICHT item no. 4730-107)after year of construction 2020 Thermal sensor ENO no. 71673 (TOPLICHT item no. 4730-114)

ENO No. 71673 All FORCE 10 stoves are equipped with a thermal sensor and an electric ignition on each gas burner.The thermocouples are sensors that only allow gas to escape from the valve when the flame is burning. As soon as the flame goes out - for example due to a gust of wind or boiling pots - the thermal sensor cools down and the gas supply is interrupted immediately.When igniting a gas burner, it should be noted that the thermocouple must first reach a certain temperature before the gas supply is released. This is done by holding down the gas control button for the corresponding burner for approx. 20 seconds after ignition so that the thermosensor does not interrupt the gas supply.The thermal sensors of the top burners on the stoves have been further developed over the years.SABAF II gas burners were used from 2000 to 2012, after which the more advanced SABAF III burners were used.The SABAF II burners can be recognized by the fact that their burner caps are fixed with two screws.the following thermocouples were installed in the top burners of the FORCE 10 gas stoves:Year of manufacture 2000 - 2012 Thermal sensor ENO no. F89216 (TOPLICHT item no. 4730-108)Year of construction 2012 - 2020 Thermal sensor ENO no. 60032 (TOPLICHT item no. 4730-107)after year of construction 2020 Thermal sensor ENO no. 71673 (TOPLICHT item no. 4730-114)

ENO No. 72647 Battery holder for holding an AA 1.5 volt battery to supply the ignition box of the ENO / FORCE 10 gas stoves with power and thus reliably and conveniently ignite the individual gas burners.

ENO No. 55036 This black locking knob is suitable for ENO / FORCE 10 pot holders.The knob has a diameter of 34 mm and has an integrated 4 mm threaded screw.The pot holder is fixed by screwing the handwheel into the pot frame and can be moved back and forth by loosening it.

ENO No. F89248 Gas burner control knob for FORCE 10 stoves. 3-part, consisting of base plate, stainless steel spring and rotary knob. Outer diameter of the base plate 46 mm.