Bronze boom fitting

Reefing claw and bond-bridge SPRENGER

Strong stainless steel boom fitting for sailing boats and small yachts.The boom claw has four nylon rings to protect the boom and the sail.Material thickness: 6 mm.Made in Germany!

From €56.00 *

Details

Brass reefing claw and bond-bridge

Classic boom fitting for sailing boats and small yachts with roller-reefing (with turning booms). The boom claw has four nylon rings to protect the boom and the sail.For simple sheet leads, use just one boom claw.By combining two boom claws, a complete, strong sheet car (lenght 300 mm) with three purchase points can be mounted, on which the mainsheet can be attached. Deliverable in two versions: a small one made from brass, cleanly polished or a bigger one made from aluminium bronze

From €116.00 *

Details

Bronze mast fitting

Classic mast-fitting set for round masts and round, oval, or square booms.Made in England, from high-quality marine bronze.The mast fitting is made up of two strong bolted rings of cast bronze, polished, and the screwed-on gooseneck.The (undrilled) boom fitting is cast in a single piece and can be either embedded in the boom or attached to the outer boom.The connected gooseneck is also a cleanly made cast piece.We offer this fitting mounted as a complete set, with a welded-on reefing hook fitting (for two reefs).D2 is the mast diameter.This fitting has a hand-crafted design and finish, and matches very well with our gaff saddle fitting.Other sizes and combinations are available on demand.

From €729.01 *

Details

Gaff saddle fitting

Traditional gaff claw (claw fitting).The sturdy gaff saddle has a hand sewn leather cover, which protects the mast finish and may be greased to ease sliding.The gaff end fitting is cast of marine bronze and hand-polished.Clew fitting with ring for the halyard and for the sail, made of welded bronze, shiny polished.This hand-finished fitting is a functional piece of art for any traditional boat or yacht.The complete set matches our mast and boom fittings in size and finish.D2 should not be less than 1.15 times the size of the largest mast diameter.Not appropriate for high peak or Gunter riggings. The inclination of the gaff should not be less than 40°.Other sizes and combinations are available on demand.

From €719.00 *

Details

Bronze mast traveller

Ring for lugger rigging, to hoist the yard (gaff).Beautiful simple bronze fitting, welded, cleanly sewn by hand with leather.The halyard suspension is constructed in such a way that the ring stays approximately horizontal under load and thus has little friction.D2 should be approximately 1.2 times the size of the largest mast diameter.

From €174.00 *

Details

Gunmetal mast band with 2 eyes DAVEY

Mast or bowsprit fitting with two attachment eyes for stays, shrouds, etc.Cylindrical. Hand-polished cast bronze.Undrilled. 2 eyes.

From €68.00 *

Details

Galvanized mast band with 2 eyes DL3416

Mast or bowsprit fitting with two attachment eyes for stays, shrouds, etc. Cylindrical.Hot-dip galvanized cast iron.Undrilled. 2 eyes.

€47.40 *

Details

Bronze mast band with 4 eyes DAVEY

Classic mast bands made of cast in gunmetal, also suitable as a jib boom fitting.With four fixing eyes for stays, shrouds etc..Cylindrical fitting that is best mounted on a spar recess.Undrilled.

From €78.00 *

Details

Bronze boom fitting

Made from cast bronze, equipped with a strong strap for the main sheet block.Surface: tumbled with matt finish, European make.

€278.00 *

Details

Boom fitting bronze

One-piece fitting, matches our gooseneck fittings (match the bolt diameter D4).Polished bronze.Also fits slightly tapered booms.

€131.99 *

Details

Bronze sliding goosneck

Functional bronze gooseneck applicable for small yachts.Matte-rolled finish. Track rails to screw on, car with holding screw as well as square spike that can be plugged on a wooden or aluminium boom.Track: L = 300 mm, W = 22 mm. Spike: 12 x 12 mm, L = 100 mm.This fitting allows the mainsail to be reefed by rotating the boom.The square socket in the boom (13 x 13 mm) has to be set up by the owner.

€118.00 *

Details

Bronze reefing gear DAVEY

This traditional three-part fitting of hand-polished cast bronze allows sails to be reefed by rolling them around the boom (simple roller reefing). Intended for yachts and small cruisers (with mainsail sizes up to about 10 square meters). The complete fitting is put together from three pieces. The boom can be removed from the tetrahedral fitting. To reef, the boom is simply pulled aft off the fitting and turned.The pieces must be installed separately: 1) Boom fitting forward (tack) for the the boom's diameter D1 = 50 mm with suitable space for the tetrahedron of the gooseneck fitting. 2) Boom fitting aft (clew) with the rolling frame for the topping lift and sheet; 3) Gooseneck with tetrahedral fitting, sized for various mast diameters: D2 = 50 to 87 mm.

From €89.00 *

Details

Backstay lever HIGHFIELD DAVEY

The HIGHFIELD lever is a reliable bronze backstay turnbuckle.An absolutely classic fitting, built the same way for the past 100 years. Not only robust hand quality by the British manufacturer DAVEY & Co., but also a piece of art on any deck.The whole fitting is made by hand from bronze, sand-cast and extensively hand-polished and hand mounted.The backstay wire must be pressed or spliced onto the bronze thimble. With the clamping lever, the wire can then be brought down tight to the deck.In the tensioned position, the wire sits below the pivot of the turnbuckle. Thus the locking device is automatically secured. The optional two-piece release fitting (must be ordered separately, available for size 1) allows the (loose) backstay wire to be hooked directly to the turnbuckle.

From €320.00 *

Details

Bronze Shroud Holder / Rigg Fitting

The shroud hanger is a traditional mast fitting for holding shrouds that are slipped over the mast with covered wire rope loops. The receiving width is 12mm. Heavy and solid, the fitting is made of cast bronze with a fine matt tumbled surface and has five countersunk holes with a diameter of 5 mm.For an additional charge, the fitting can also be supplied hollowed, i.e. precisely adapted to the required mast diameter. Just ask, we will be happy to advise you.

€179.00 *

Details

Brass Mast Cleat / Jam Cleat WILMEX

Brass cleat with curved base for direct attachment to the spar (bearing radius 41 mm). In addition to being used as a mast cleat for halyards, it can also be used on the main boom to attach reefing tackles and stretchers or on the jib boom to attach the jib ringhaul or the water stay. The elegant cleat is produced by WILMEX and is designed for rope diameters of 10-14 mm.

€198.00 *

Details

Bronze heavy duty mastbands EAST COAST

Strong mast fittings with a high breaking load that can also be used as bowsprit fittings. Made in England and finished in polished bronze. With very strong, drilled lugs and wide strap for secure fastening.Available with two or four lugs.

From €112.00 *

Details

Bowsprit traveller EAST COAST

Bowsprit traveller for hauling out the jib sail on the jib boom or bowsprit. Hergestellt in Enghland. Heavy-duty A4 stainless steel fitting with solidly constructed, drilled plates. Well suited for attaching a headsail furling system. Bolting the furling gear into plates reduces the tendency for the furling line to snarl up. The ring is neatly stitched with rigging leather. Comes without bolt. Other sizes on request. Please note that bowsprit travellers are specified by the bowsprit they will work on. Normally they are sized 30% larger in diameter than the bowsprit.

From €338.00 *

Details

Bronze bowsprit fitting EAST COAST

Open bowsprit fitting in very strong design with high breaking load. Made in England from polished bronze.The wide strap is equipped with drilled lugs on every side. The lug at the top has two holes. The front of the two eyes is usually used as an attachment point for a fixed stay or for bowsprit halyard (dutch sailing barges). The sail or an outhaul block for the bowsprit traveller can be attached to the inner eye.Well-suited for recessing into the wood, in order to have the fitting band and boom nock finish off in an attractive manner.

From €477.00 *

Details

Bronze sheet buffer

The traditional American-style sheet shock absorber is cast from solid bronze.The ring is attached to long V-brackets. The rubber rings attached centrally round the axle dampen the shock of the sheet block and thereby protect the fittings and the joints.Fastened from below with bolts (M20) to be screwed into the base.Surface: fine matt tumbled.Other sizes on request.

€2,399.00 *

Details

Bronze bowsprit fitting

Classic fittings made from rugged cast bronze with eyes to bend wires to the spar on all 4 sides.The two eyes for the stays on top and the one below for the bobstay have been designed especially robust.Surface: tumbled with matt finish, European make.Available in two types: as an open ring or closed end fitting.Additional sizes are available on request.

From €325.00 *

Details

Mon - Fri:	09 am - 06 pm
Sat:	09 am - 01 pm

Bronze boom fitting

Bronze boom fitting

Description