Advaced development of the AIRO-NAUTIC epoxy filler with decidedly lower mass per unit area (approx. 0,5-0,7 kg/l).Inexpensive all-around epoxy resin - fine filler.Two component finishing filler for all boatbuilding materials.Does not absorb water, thus is very good for underwatersurfaces and is intended as an osmosis barrier. Good filler for osmosis repair.A thin layer results in a very fine surface.Colour: light grey.

Simple, single-component fine and smoothing filler for wood and single-component paint systems above the waterline. Suitable for leveling unevenness on surfaces, for example as an intermediate step after priming and before the first coat of paint.&nbsp

EPIFANES 1500 is a non-shrinking, two-component epoxy-based filler.This filler provides smooth surfaces and can be applied in thick coats. It is exceptionally easy to sand and is suitable for all common boatbuilding materials above and below water. It can be applied to vertical surfaces in layers up to 2 cm thick in one operation, and even thicker in horizontal surfaces without shrinking during curing.After thorough degreasing and sanding, the cured filler can then be recoated with a 2-component system. Smaller repair areas can also be overcoated with 1K paints, such as EPIFANES MULTI-MARINE Primer. Mixing ratio 2:1.Tip: EPIFANES Fibreglass Prep Cleaner is suitable as a cleaner for degreasing the filled surface.

Two-component, resistant epoxy fine filler that does not shrink during curing and achieves a particularly smooth surface. Before mixing, the individual components should first be stirred well alone and then together. The filler can then be applied in thin layers (up to 1 mm layer thickness on vertical surfaces). If the surface is to be painted with 1-component varnish afterwards, a layer of 2-component varnish or primer must be applied first.Color: gray.

Two-component filler for minor repairs above the waterline for steel and GRP (polyester), which can also be applied in thick layers. Can be overcoated with 1- and 2-component paints and lacquers.Application: Place the desired amount of filler on a clean mixing board and add 2-4% hardener. Mix both thoroughly. Work quickly. It is advisable to mix smaller quantities more frequently, especially when working at higher temperatures. This helps to avoid mixing too much; additionally, larger amounts of mixed filler harden faster.Tip: Sand immediately after drying and prime with 20% diluted paint to prevent moisture absorption and shrinkage of the paint layers.Safety note: Contains styrene. Use only outdoors or in well-ventilated areas and wear personal protective equipment (mask, eye protection, gloves) during application. The shipment of this product is only permitted in accordance with the EU Chemicals Prohibition Ordinance  (REACH) to resellers, professional users, and public research and educational institutions. Are you part of this customer group? Then send us your inquiry here. We will be happy to provide you with a delivery offer.Technical DataApplication: Surface touch-ups, small repairsSubstrate: GRP or existing paint systems above the waterline Application method: Manual fillingSubsequent coating: with all common 1K and 2K products from EPIFANESPot life (working time): 5-10 minutesDrying times at 18°C: 30-60 minutes 

Solvent free, two component fine filler based on epoxy, that is especially waterproof.This very effective putty can be employed above or below water on all surfaces sealed with any kind of epoxy primer.It hardens to a smart, glue free surface, that is easy to sand and does not shrink up to a lamination strength of 20mm.Content: 500g, colour: light greyProduct Safety: For this product the hazard pictograms and signal words shown above apply, as well as the following hazard statements: H302, H314, H315, H319, H317, H411, H412..

Solvent free, two component fine filler based on epoxy and compounded with special fibres, that is waterproof and especially well suited for applications where high mechanical strains have to be absorbed.This very effective putty can be employed above or below water on all surfaces sealed with any kind of epoxy primer.Also very well suited for the filling of very rough unevenness.Laminations of up to 30mm are possible in one working cycle.It hardens to a smart, glue free surface, that is easy to sand and does not shrink.Content: 500g, colour: light blue.

AIRO - NAUTIC epoxy filler. Inexpensive all-around epoxy resin - fine filler. Two component finishing filler for all boatbuilding materials. Does not absorb water, thus is very good for underwater surfaces and is intended as an osmosis barrier. A thin layer results in a very fine surface.Colour: Light grey. Also available in exceptionally cheap large containers.

YACHTCARE EPOXY FEINSPACHTEL is a quick-drying 2-component epoxy filler with the highest surface quality. The thixotropic fine filler, which is particularly easy to sand, produces a surface with very low pore volume. It is used for the fine processing of surfaces from painting, as well as for the reconditioning and covering of various materials in above and below water areas. YACHTCARE EPOXY FEINSPACHTEL is solvent-free and is characterised by its high water resistance and good sanding properties. Area of application: Universal for all imaginable fine filling work above and below water. Suitable for boat building materials such as GFK, CFK, steel, aluminium and non-working wood. GRP, steel and aluminium substrates must be primed with a 2-component epoxy primer such as EPOXY PRIMER. Colour: cream white.

Easy-to-use fine layer filler for repairing minor damage to the gelcoat layer.The filler is formulated so that it does not sag on vertical surfaces and can also be used in an environment with high humidity.After curing, the gelcoat filler forms a high-gloss, hard and non-sticky surface.