Fuel filter TOC-DUO-N

Accessories for fuel filter OVENTROP.

Relaxed, bendable copper pipe for simple installation.Outer diameter 8 mm.

Electric fuel pump that can be used to bring fuel to a stove if the primary tank is below the level of the fuel regulator and the installation of a day tank is not possible.This membrane pressure pump with electrically regulated electromagnetic works is maintenance-free and nearly wear-free.Data:- Dimensions: 73 x 128 mm,- Output: 120 l/h,- Pressure lift: 0.25 bar (max. 2,5 m),- Suction lift: -0.10 bar (max. 1,0 m),- Attachement fittings for hose 8 mm on both sides.

For the hot-water circuit. Made of cleanly welded stainless steel plate.With fill closure, 1/2" bottom pipe fitting and 8 mm fuel pipe connection for the overflow line.

Filtercartridge for fuel filter OVENTROP.

Spare filter for OVENTROP oil filters.Type PN10.25my.

For diesel and heating oil. Brass housing, clear plastic filter, washable filter insert of nickel mesh 100-150 µm.Complete with holding bracket of galvanized steel and brass fuel pipe connection for 8 mm copper pipe.Comes without shut-off valve.

Fuel pipe connection for 8 mm pipe diameter.Melting cap for automatic closing during a fire.

Fuel pipe connection for 8 mm pipe diameter.Melting cap for TOBY oil metering valves for automatic closing in the event of a fire.

Brass compression fitting for 8mm tube.

Cleanly welded tanks of stainless steel plate.Complete with filler pipes, shut-off valves (1/4" threads) for 8 mm copper line with mounting tabs.Comes without separator pipe for level indicator.We can also finish tanks to your specifications. Please ask!

Cleanly welded tanks of stainless steel plate.Complete with filler pipes, shut-off valves (1/4" threads) for 8 mm copper line with mounting tabs.Comes with separator pipe as level indicator.We can also finish tanks to your specifications. Please ask!

OVENTROP brass OILPUR heating oil filters for stoves and heaters, which are operated in a sucking mode single line system. Nominal size DN10 (G 3/8"), with a clear plastic filter and a washable filter insert of nickel mesh 100-150 µm.Complete with holding bracket of galvanized steel and brass fuel pipe connection for 8 mm copper pipe.In the return pipe version the filter has two connectors with a male thread G 3/8" with internal cone fitting to the burner tubing and a hand venting valve in order to start the burner.

Pipe clip nylon, suitable for copper fuel pipes.

Pipe clip niro, suitable for copper fuel pipes.

Expansion tank for heat and pressure-water installations.Tank with integrated membrane for constant pressure (max. 8 bar).

Made from seawater-proof bronze (Rg 7). Essential for the control of, for example, fuel or tank connections.Red-painted aluminum handle.A switch cable can be attached at the handle bore hole - with firmly ancored valve - in order to open or shut the flow rate.The angle of the lever is approx. 30°.

7 litre petroleum pressure tank from TAYLOR's, e.g. for the 079K petroleum heater, the 028 petroleum cooker or the 029 petroleum cooker with grill.The tank is made of stainless steel and fitted with a bicycle valve (Dunlop or lorry valve). It has a level indicator and a pressure gauge.The pressurised tank can be mounted in any position and is connected to the heater or cooker with a copper pipe.Dimensions: 180 x 340 x 290 mm (D x L x H).

All REFLEKS heating systems with a water circuit should be equipped with this shut-off valve.The KBB fire protection valve is a compact valve in a corrosion-resistant, non-flammable design that operates purely mechanically and does not require a power supply.The temperature sensor is connected to the valve via a permanently soldered capillary line.As soon as the temperature at the sensor exceeds the set value (90°), the oil supply to the stove is immediately interrupted by the valve.The valve remains closed until the reset button is pressed.The valve can also be triggered manually by pulling the reset button.The valve (supplied with connection material for 8 mm pipes, SR 8 mm cutting ring fitting on both sides) is installed in the oil supply line directly upstream of the regulator.The temperature sensor measures the flow hot water temperature near the heater. If the set temperature (90°C) is exceeded, the oil supply is shut off immediately.To connect the sensor to the heating pipework, use a copper T-piece with two G ½" male threaded pipe fittings (please order item no. 4292-100 separately). The vertical branch of the T-piece does not have direct access to the water circuit of the heating system, but is soldered onto the water-carrying pipe and serves to accommodate the temperature sensor.Care must be taken during installation to ensure that the capillary line is not kinked under any circumstances. Length of the sensor line 200 cm.

Tool for loosening the union screw connection of fuel filters or for loosening filtercartridge.