Skip to main content


The small cast iron stove Salamander SE has been specially developed for small rooms. Logs, coal or eco-briquettes can be burned in it. Its heating capacity is 4 kW.

The efficiency is a very good 81.4 percent. The low particle and gas emissions meet the European ECO DESIGN regulations and even fall below the new, stricter limits of the HETAS Cleaner Choice Scheme. This allows the Salamander SE to be operated in the so-called "smoke-free zones" in the UK. The HETAS Cleaner Choice Scheme is designed to help improve air quality in the UK by setting strict limits for smoke emissions and particulate matter.

The user-friendly air regulator on the front of the stove allows the secondary and tertiary air supply to be precisely adjusted. The firing rate and flame pattern can thus be controlled very precisely. The preheated tertiary air intake helps to ensure efficient, clean combustion. The secondary combustion technology keeps the large viewing window clean.

Installation is possible not only on board ships, but also in construction trailers or mobile Tiny Houses.

With the angled flue flange, the chimney pipe can be mounted on the back of the stove instead of on top. The stove base raises the stove by 158 mm and creates space for firewood.

The exhaust pipe connection has an inner diameter of 4" (100 mm) and a slightly tapered outer diameter of 115 mm. This means you can put pipes with an outer diameter of 100 mm into the flange or you can put on pipes with an inner diameter of 115 mm.
We offer an adapter for our REFLEKS stainless steel pipes in size 114 mm so that the entire REFLEKS flue pipe system can be used.

Accessories:

  • 4356-100: Stand to raise the height of the stove by 158 mm, this also creates space for firewood.
  • 4356-101: Rear flue wedge 90° for mounting the flue system on the back of the stove instead of on the top.
  • 4356-103: Vermiculite plates Cast iron heat storage plates inside the SALAMANDER SE can be replaced with Vermiculite plates.
    The SALAMANDER SE is supplied with cast iron heat storage plates as standard. Compared to cast iron plates, the firebox with vermiculite plates heats up much faster due to its insulating properties, which increases the efficiency of the stove.
  • 4356-108: Removable hot plate that increases the thermal mass of the SALAMANDER oven by 7 kg. The plate can be used to place washing kettles or pots to keep food warm. It can be used only if the flue pipe system is mounted on the back of the stove.
  • 4282-115: Exhaust pipe adapter, for REFLEKS stainless steel pipes size 114 mm.

Spare parts:
These items are included with each stove, but are also available as replacements.


Accessories

Adapter for SALAMANDER SE to REFLEKS exhaust pipe
Adapter suitable for oven SALAMANDER SE, which enables the use of REFLEKS stainless steel pipes of size 114 mm.

€44.00 *
Flue pipe elbow 45° REFLEKS
This flue pipes matches the REFLEKS heating system and other gas or coal stoves with matching exhaust outlets.Made of acid-proof stainless steel (wall depth 0.6 mm).Plugs together: slightly conical with pressed sleeve on one side.

From €56.90 *
Flue pipe elbow 90° REFLEKS
This flue pipes matches the REFLEKS heating system and other gas or coal stoves with matching exhaust outlets.Made of acid-proof stainless steel (wall depth 0.6 mm).Plugs together: slightly conical with pressed sleeve on one side.

From €61.00 *
Flue pipes REFLEKS
This flue pipes matches the REFLEKS heating system and other gas or coal stoves with matching exhaust outlets.Made of acid-proof stainless steel (wall depth 0.6 mm).Plugs together: slightly conical with pressed sleeve on one side.

From €29.90 *
Flue guard REFLEKS
Guard for flue pipes that are installed in close quaters.Avaiable in stainless steel, brass or copper plate.The risk of contact burns is minimized, but the warmth of the pipe can still be enjoyed.Matches REFLEKS flue pipes of 70 mm or 90 mm.The flue guard is attached to the flue pipe and fixed with two stainless steel brackets, which are included in the package.Distance from flue pipe, 15 mm.

From €109.00 *
Wall shade inox
Small reflector plate for heat protection behind flue pipes.Plate stainless steel.Measurements:50cm high, 15cm wide.Available as flat or recessed version.The flat plate must be mounted with spacers or insulation behind, the recessed plate can be mounted directly on the wall.

From €35.90 *
Deck ducts square REFLEKS
Deck through hull of stainless steel.With square deck plate.

From €115.50 *
Deck through hull REFLEKS
Deck through hull with round deck plate, stainless steel. Suitable for our REFLEKS flue pipes.

From €128.00 *
Through hull inclined REFLEKS
Through-deck fitting with round, inclined deck plate.Made of stainless steel.Avaialable in various angles for adapting to the deck inclination.Fits the REFLEKS flue pipes.

From €149.00 *
Deck through hull REFLEKS components
Components for mounting a through-deck fitting that matches your deck inclination perfectly.Pipe, a round deck plate and flange to weld locally.Made of stainless steel.Fits the REFLEKS flue pipes.

From €98.00 *
Cap for through-hull REFLEX
Closing cap, stainless steel. Suitable for all REFLEKS flue pipes.

From €48.00 *
Insulated flue pipe REFLEKS
Thickness 0.6 mm, insulated with 10 mm of rock wool.Above all, at the lowest temperatures, double flue pipes are necessary outside, so that the draft through very cold pipes can be restricted.

From €156.00 *
Insulated flue pipe elbow 45° REFLEKS
Thickness 0.6 mm, insulated with 10 mm of rock wool.Above all, at the lowest temperatures, double flue pipes are necessary outside, so that the draft through very cold pipes can be restricted.

From €168.00 *