Wind chargers

A wind generator that has proven its quality, reliability and performance on yachts, ships and on shore for almost 20 years. This generator delivers energy autonomously and unattended even under extreme conditions. Perfectly matched components result in an overall system of highest operational safety and reliability.Similar to a large wind turbine, the SUPERWIND 350 adjusts its rotor blades, thus limiting aerodynamic loads where they occur, directly on the rotor. High loads on the entire structure are avoided and the service life is increased. The control mechanism is fully integrated into the hub and thus protected against environmental influences.The SUPERWIND Type 350-II features even better bearing technology, making it suitable for very rough sites. The patented, fully synchronized rotor hub ensures a very high turbulence resistance and, together with the optimized rotor bearing, increases stability and durability.Combination with solar systems is possible.Available for 12V, 24V and 48 on-board power supply.The optional stop switch is used to electromechanically stop the wind generator if it is not to be operated or if the rotor is to be prevented from starting. When used on sailing yachts, the installation of the stop switch is strongly recommended in order to be able to shut down the Superwind at sea in extreme weather.The charge controller, which must be ordered separately, also includes the load resistors that dissipate excess energy when the battery is fully charged.A mounting spigot for a 1 1/2" pipe mast (inner diameter = 44.3 mm) and an adapter sleeve for a 2" pipe (with different inner diameters) are included.Technical dataRated power 350 WNominal wind speed 12,5 m/sswitch-on wind speed 3.5 m/sshut-off wind speed nonerotor diameter 1.22 mNumber of blades 3Rotor blade material CFRPspeed 500 - 1300 rpmGenerator Permanent magnet, 3-phase with rectifier, neodymium magnetsRated voltage Available in 12 V DC , 24 V DC and 48 V DCspeed and power control Rotor blade pitch control, fully synchronizedmain brake generator short circuittotal mass 11.5 kgRotor thrust, operation 70 Nrotor thrust, extreme gust 220 N

Lightweight, robust generator with high energy output (420 watts at 12 volts) and effective start-up even in light winds (from 4.3 knots wind). Hand-laminated rigid carbon rotor blades ensure extremely quiet running in virtually maintenance-free continuous operation.The body and the wind vane are made of powder-coated, seawater-resistant aluminum. The scope of delivery includes anExternal MPPT hybrid charge controller (220 x 150 x 82 mm, weight 2.6 kg) with additional connection for solar panels (up to 300 Wp), with integrated electronic stop switch and external antenna for good Bluetooth connection. The charge controller is of course also suitable for Lihtium batteries.Thanks to the Bluetooth interface, an external smartphone or tablet can be used to display not only all relevant operating parameters but also the amount of energy charged and the consumption of the devices connected to the load output in Ah.Suitable for a mast with an outer diameter of 48 mm.A mounting kit and replacement rotor blades are available.Technical data:Rotor diameter: 1150 mm.Rotation circle: 1170 mm.Length: 650 mmWeight: 6.8 kg.Voltage: 12/24/48 VPower: 420 W/450/500 W (12V/24V/48V)

Mounting kit for the mast of the Silentwind generator consisting of a mast base with rubber damper, two mast clamps and two deck fittings for side struts, all made of polished stainless steel. Suitable for tubes with an outer diameter of 48 mm (or 1 1/2 inch).The mast base is fitted with a rubber damper that provides noise and vibration decoupling between the mast and the hull. The mast base has a central opening for the cable feed-through into the deck so that it does not have to be routed out of the mast tube to the side. The bracket can also be used for mounting masts for radar and satellite systems. It can be swiveled and can therefore also be mounted on sloping surfaces. Rubber adapters allow the device to be adapted to different internal pole tube diameters.Pole tube and tubes of the side supports are not included in the scope of delivery.Scope of delivery:Pole base pre-assembled: Center section with cable guide, 2x mounting bracket, rubber mast mount, mast washer, mounting accessoriesPole clamps pre-assembled: 2x pole clamp, 2x rubber damping profile, 2x strut end piece, mounting accessories2x lower strut end piece with mounting plateRubber adapter sleeve for mast base

The external temperature sensor for the SCR charge controllers from SUPERWIND ensures optimum adjustment of the charge termination voltage of the charge controller.